git.openwrt.org Git - openwrt/staging/blogic.git/log

irqchip/gic-v3-its: Don't assume GICv3 hardware supports 16bit INTID

The current ITS driver is assuming every ITS hardware implementation
supports minimum of 16bit INTID. But this is not true, as per GICv3
specification, INTID field is IMPLEMENTATION DEFINED in the range of
14-24 bits. We might see an unpredictable system behavior on systems
where hardware support less than 16bits and software tries to use
64K LPI interrupts.

On Qualcomm Datacenter Technologies QDF2400 platform, boot log shows
confusing information about number of LPI chunks as shown below. The
QDF2400 ITS hardware supports 24bit INTID.

This patch allocates the memory resources for PEND/PROP tables based
on discoverable value which is specified in GITS_TYPER.IDbits. Also
it fixes the log message that reflects the correct number of LPI
chunks were allocated.

ITS@0xff7efe0000: allocated 524288 Devices @3c0400000 (indirect, esz 8, psz 64K, shr 1)
ITS@0xff7efe0000: allocated 8192 Interrupt Collections @3c0130000 (flat, esz 8, psz 64K, shr 1)
ITS@0xff7efe0000: allocated 8192 Virtual CPUs @3c0140000 (flat, esz 8, psz 64K, shr 1)
ITS: Allocated 524032 chunks for LPIs
PCI/MSI: ITS@0xff7efe0000 domain created
Platform MSI: ITS@0xff7efe0000 domain created

Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/gic-v3-its: Add ACPI NUMA node mapping

Add code to parse SRAT ITS Affinity sub table as defined in ACPI 6.2.
Later in per device probe, ITS devices are mapped to numa node using
ITS Id to proximity domain mapping.

[maz: fix dependency on ACPICA, fixed structure name, minor cleanups]

Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/gic-v3-its-platform-msi: Make of_device_ids const

of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/gic-v3-its: Make of_device_ids const

of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/irq-mvebu-icu: Add new driver for Marvell ICU

The Marvell ICU unit is found in the CP110 block of the Marvell Armada
7K and 8K SoCs. It collects the wired interrupts of the devices located
in the CP110 and turns them into SPI interrupts in the GIC located in
the AP806 side of the SoC, by using a memory transaction.

Until now, the ICU was configured in a static fashion by the firmware,
and Linux was relying on this static configuration. By having Linux
configure the ICU, we are more flexible, and we can allocate dynamically
the GIC SPI interrupts only for devices that are actually in use.

The driver was initially written by Hanna Hawa <hannah@marvell.com>.

Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/irq-mvebu-gicp: Add new driver for Marvell GICP

This commit adds a simple driver for the Marvell GICP, a hardware unit
that converts memory writes into GIC SPI interrupts. The driver provides
a number of functions to the ICU driver to allocate GICP interrupts, and
get the physical addresses that the ICUs should write to to set/clear
interrupts.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

dt-bindings/interrupt-controller: Add DT binding for the Marvell ICU

This commit adds the Device Tree binding documentation for the Marvell
ICU interrupt controller, which collects wired interrupts from the
devices located into the CP110 hardware block of Marvell Armada 7K/8K,
and converts them into SPI interrupts in the GIC located in the AP
hardware block, using the GICP extension.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

genirq/irqdomain: Remove auto-recursive hierarchy support

It did seem like a good idea at the time, but it never really
caught on, and auto-recursive domains remain unused 3 years after
having been introduced.

Oh well, time for a late spring cleanup.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

irqchip/MSI: Use irq_domain_update_bus_token instead of an open coded access

Now that we have irq_domain_update_bus_token(), switch everyone over
to it. The debugfs code thanks you for your continued support.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

genirq/irqdomain: Add irq_domain_update_bus_token helper

We can have irq domains that are identified by the same fwnode
(because they are serviced by the same HW), and yet have different
functionnality (because they serve different busses, for example).
This is what we use the bus_token field.

Since we don't use this field when generating the domain name,
all the aliasing domains will get the same name, and the debugfs
file creation fails. Also, bus_token is updated by individual drivers,
and the core code is unaware of that update.

In order to sort this mess, let's introduce a helper that takes care
of updating bus_token, and regenerate the debugfs file.

A separate patch will update all the individual users.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

genirq/affinity: Assign vectors to all present CPUs

Currently the irq vector spread algorithm is restricted to online CPUs,
which ties the IRQ mapping to the currently online devices and doesn't deal
nicely with the fact that CPUs could come and go rapidly due to e.g. power
management.

Instead assign vectors to all present CPUs to avoid this churn.

Build a map of all possible CPUs for a given node, as the architectures
only provide a map of all onlines CPUs. Do this dynamically on each call
for the vector assingments, which is a bit suboptimal and could be
optimized in the future by provinding a mapping from the arch code.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-nvme@lists.infradead.org
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20170603140403.27379-5-hch@lst.de

x86/apic: Mark single target interrupts

If the interrupt destination mode of the APIC is physical then the
effective affinity is restricted to a single CPU.

Mark the interrupt accordingly in the domain allocation code, so the core
code can avoid pointless affinity setting attempts.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235447.508846202@linutronix.de

genirq/cpuhotplug: Avoid irq affinity setting for single targets

Avoid trying to add a newly online CPU to the effective affinity mask of an
started up interrupt. That interrupt will either stay on the already online
CPU or move around for no value.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235447.431321047@linutronix.de

genirq: Introduce IRQD_SINGLE_TARGET flag

Many interrupt chips allow only a single CPU as interrupt target. The core
code has no knowledge about that. That's unfortunate as it could avoid
trying to readd a newly online CPU to the effective affinity mask.

Add the status flag and the necessary accessors.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235447.352343969@linutronix.de

genirq/cpuhotplug: Handle managed IRQs on CPU hotplug

If a CPU goes offline, interrupts affine to the CPU are moved away. If the
outgoing CPU is the last CPU in the affinity mask the migration code breaks
the affinity and sets it it all online cpus.

This is a problem for affinity managed interrupts as CPU hotplug is often
used for power management purposes. If the affinity is broken, the
interrupt is not longer affine to the CPUs to which it was allocated.

The affinity spreading allows to lay out multi queue devices in a way that
they are assigned to a single CPU or a group of CPUs. If the last CPU goes
offline, then the queue is not longer used, so the interrupt can be
shutdown gracefully and parked until one of the assigned CPUs comes online
again.

Add a graceful shutdown mechanism into the irq affinity breaking code path,
mark the irq as MANAGED_SHUTDOWN and leave the affinity mask unmodified.

In the online path, scan the active interrupts for managed interrupts and
if the interrupt is functional and the newly online CPU is part of the
affinity mask, restart the interrupt if it is marked MANAGED_SHUTDOWN or if
the interrupts is started up, try to add the CPU back to the effective
affinity mask.

Originally-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20170619235447.273417334@linutronix.de

genirq: Handle managed irqs gracefully in irq_startup()

Affinity managed interrupts should keep their assigned affinity accross CPU
hotplug. To avoid magic hackery in device drivers, the core code shall
manage them transparently and set these interrupts into a managed shutdown
state when the last CPU of the assigned affinity mask goes offline. The
interrupt will be restarted when one of the CPUs in the assigned affinity
mask comes back online.

Add the necessary logic to irq_startup(). If an interrupt is requested and
started up, the code checks whether it is affinity managed and if so, it
checks whether a CPU in the interrupts affinity mask is online. If not, it
puts the interrupt into managed shutdown state.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235447.189851170@linutronix.de

genirq: Add force argument to irq_startup()

In order to handle managed interrupts gracefully on irq_startup() so they
won't lose their assigned affinity, it's necessary to allow startups which
keep the interrupts in managed shutdown state, if none of the assigend CPUs
is online. This allows drivers to request interrupts w/o the CPUs being
online, which avoid online/offline churn in drivers.

Add a force argument which can override that decision and let only
request_irq() and enable_irq() allow the managed shutdown
handling. enable_irq() is required, because the interrupt might be
requested with IRQF_NOAUTOEN and enable_irq() invokes irq_startup() which
would then wreckage the assignment again. All other callers force startup
and potentially break the assigned affinity.

No functional change as this only adds the function argument.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235447.112094565@linutronix.de

genirq: Split out irq_startup() code

Split out the inner workings of irq_startup() so it can be reused to handle
managed interrupts gracefully.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235447.033235144@linutronix.de

genirq: Introduce IRQD_MANAGED_SHUTDOWN

Affinity managed interrupts should keep their assigned affinity accross CPU
hotplug. To avoid magic hackery in device drivers, the core code shall
manage them transparently. This will set these interrupts into a managed
shutdown state when the last CPU of the assigned affinity mask goes
offline. The interrupt will be restarted when one of the CPUs in the
assigned affinity mask comes back online.

Introduce the necessary state flag and the accessor functions.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.954523476@linutronix.de

x86/apic: Implement effective irq mask update

Add the effective irq mask update to the apic implementations and enable
effective irq masks for x86.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.878370703@linutronix.de

xen/events: Add support for effective affinity mask

Update the effective affinity mask when an interrupt was successfully
targeted to a CPU.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.799944725@linutronix.de

x86/apic: Add irq_data argument to apic->cpu_mask_to_apicid()

The decision to which CPUs an interrupt is effectively routed happens in
the various apic->cpu_mask_to_apicid() implementations

To support effective affinity masks this information needs to be updated in
irq_data. Add a pointer to irq_data to the callbacks and feed it through
the call chain.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.720739075@linutronix.de

x86/apic: Move cpumask and to core code

All implementations of apic->cpu_mask_to_apicid_and() and the two incoming
cpumasks to search for the target.

Move that operation to the call site and rename it to cpu_mask_to_apicid()

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.641575516@linutronix.de

x86/apic: Move online masking to core code

All implementations of apic->cpu_mask_to_apicid_and() mask out the offline
cpus. The callsite already has a mask available, which has the offline CPUs
removed. Use that and remove the extra bits.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.560868224@linutronix.de

x86/uv: Use default_cpu_mask_to_apicid_and()

Same functionality except the extra bits ored on the apicid.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.482841015@linutronix.de

x86/apic: Move flat_cpu_mask_to_apicid_and() into C source

No point in having inlines assigned to function pointers at multiple
places. Just bloats the text.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.405975721@linutronix.de

genirq/cpuhotplug: Use effective affinity mask

If the architecture supports the effective affinity mask, migrating
interrupts away which are not targeted by the effective mask is
pointless.

They can stay in the user or system supplied affinity mask, but won't be
targetted at any given point as the affinity setter functions need to
validate against the online cpu mask anyway.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.328488490@linutronix.de

genirq: Introduce effective affinity mask

There is currently no way to evaluate the effective affinity mask of a
given interrupt. Many irq chips allow only a single target CPU or a subset
of CPUs in the affinity mask.

Updating the mask at the time of setting the affinity to the subset would
be counterproductive because information for cpu hotplug about assigned
interrupt affinities gets lost. On CPU hotplug it's also pointless to force
migrate an interrupt, which is not targeted at the CPU effectively. But
currently the information is not available.

Provide a seperate mask to be updated by the irq_chip->irq_set_affinity()
implementations. Implement the read only proc files so the user can see the
effective mask as well w/o trying to deduce it from /proc/interrupts.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.247834245@linutronix.de

genirq/proc: Replace ever repeating type cast

The proc file setup repeats the same ugly type cast for the irq number over
and over. Do it once and hand in the local void pointer.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.160866358@linutronix.de

genirq: Remove pointless gfp argument

All callers hand in GPF_KERNEL. No point to have an extra argument for
that.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.082544752@linutronix.de

genirq: Remove pointless arg from show_irq_affinity

The third argument of the internal helper function is unused. Remove it.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.004958600@linutronix.de

genirq: Move irq_fixup_move_pending() to core

Now that x86 uses the generic code, the function declaration and inline
stub can move to the core internal header.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235445.928156166@linutronix.de

x86/irq: Use irq_migrate_all_off_this_cpu()

The generic migration code supports all the required features
already. Remove the x86 specific implementation and use the generic one.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235445.851311033@linutronix.de

x86/irq: Restructure fixup_irqs()

Reorder fixup_irqs() so it matches the flow in the generic migration code.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235445.774272454@linutronix.de

genirq/cpuhotplug: Set force affinity flag on hotplug migration

Set the force migration flag when migrating interrupts away from an
outgoing CPU.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235445.681874648@linutronix.de

genirq/cpuhotplug: Add support for conditional masking

Interrupts which cannot be migrated in process context, need to be masked
before the affinity is changed forcefully.

Add support for that. Will be compiled out for architectures which do not
have this x86 specific issue.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235445.604565591@linutronix.de

genirq/cpuhotplug: Add support for cleaning up move in progress

In order to move x86 to the generic hotplug migration code, add support for
cleaning up move in progress bits.

On architectures which have this x86 specific (mis)feature not enabled,
this is optimized out by the compiler.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235445.525817311@linutronix.de

genirq/cpuhotplug: Do not migrated shutdown irqs

Interrupts, which are shut down are tried to be migrated as well. That's
pointless because the interrupt cannot fire and the next startup will move
it to the proper place anyway.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235445.447550992@linutronix.de

genirq/cpuhotplug: Reorder check logic

Move the checks for a valid irq chip and the irq_set_affinity() callback
right in front of the whole migration logic. No point in doing a gazillion
of other things when the interrupt cannot be migrated at all.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235445.354181630@linutronix.de

genirq/cpuhotplug: Dont claim success on error

In case the affinity of an interrupt was broken, a printk is emitted.

But if the affinity cannot be set at all due to a missing
irq_set_affinity() callback or due to a failing callback, the message is
still printed preceeded by a warning/error.

That makes no sense whatsoever.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235445.274852976@linutronix.de

genirq/cpuhotplug: Remove irq disabling logic

This is called from stop_machine() with interrupts disabled. No point in
disabling them some more.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235445.198042748@linutronix.de

genirq: Move pending helpers to internal.h

So that the affinity code can reuse them.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20170619235445.109426284@linutronix.de

genirq: Move initial affinity setup to irq_startup()

The startup vs. setaffinity ordering of interrupts depends on the
IRQF_NOAUTOEN flag. Chained interrupts are not getting any affinity
assignment at all.

A regular interrupt is started up and then the affinity is set. A
IRQF_NOAUTOEN marked interrupt is not started up, but the affinity is set
nevertheless.

Move the affinity setup to startup_irq() so the ordering is always the same
and chained interrupts get the proper default affinity assigned as well.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235445.020534783@linutronix.de

genirq: Rename setup_affinity() to irq_setup_affinity()

Rename it with a proper irq_ prefix and make it available for other files
in the core code. Preparatory patch for moving the irq affinity setup
around.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.928501004@linutronix.de

genirq: Remove mask argument from setup_affinity()

No point to have this alloc/free dance of cpumasks. Provide a static mask
for setup_affinity() and protect it proper.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.851571573@linutronix.de

x86/irq: Cleanup pending irq move in fixup_irqs()

If an CPU goes offline, the interrupts are migrated away, but a eventually
pending interrupt move, which has not yet been made effective is kept
pending even if the outgoing CPU is the sole target of the pending affinity
mask. What's worse is, that the pending affinity mask is discarded even if
it would contain a valid subset of the online CPUs.

Use the newly introduced helper to:

- Discard a pending move when the outgoing CPU is the only target in the
pending mask.

- Use the pending mask instead of the affinity mask to find a valid target
for the CPU if the pending mask intersects with the online CPUs.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.774068557@linutronix.de

genirq: Provide irq_fixup_move_pending()

If an CPU goes offline, the interrupts are migrated away, but a eventually
pending interrupt move, which has not yet been made effective is kept
pending even if the outgoing CPU is the sole target of the pending affinity
mask. What's worse is, that the pending affinity mask is discarded even if
it would contain a valid subset of the online CPUs.

Implement a helper function which allows to avoid these issues.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.691345468@linutronix.de

genirq: Add missing comment for IRQD_STARTED

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.614913014@linutronix.de

genirq/debugfs: Add proper debugfs interface

Debugging (hierarchical) interupt domains is tedious as there is no
information about the hierarchy and no information about states of
interrupts in the various domain levels.

Add a debugfs directory 'irq' and subdirectories 'domains' and 'irqs'.

The domains directory contains the domain files. The content is information
about the domain. If the domain is part of a hierarchy then the parent
domains are printed as well.

# ls /sys/kernel/debug/irq/domains/
default     INTEL-IR-2     INTEL-IR-MSI-2  IO-APIC-IR-2  PCI-MSI
DMAR-MSI    INTEL-IR-3     INTEL-IR-MSI-3  IO-APIC-IR-3  unknown-1
INTEL-IR-0  INTEL-IR-MSI-0  IO-APIC-IR-0    IO-APIC-IR-4  VECTOR
INTEL-IR-1  INTEL-IR-MSI-1  IO-APIC-IR-1    PCI-HT

# cat /sys/kernel/debug/irq/domains/VECTOR
name:   VECTOR
size:   0
mapped: 216
flags:  0x00000041

# cat /sys/kernel/debug/irq/domains/IO-APIC-IR-0
name:   IO-APIC-IR-0
size:   24
mapped: 19
flags:  0x00000041
parent: INTEL-IR-3
    name:   INTEL-IR-3
     size:   65536
     mapped: 167
     flags:  0x00000041
     parent: VECTOR
        name:   VECTOR
         size:   0
         mapped: 216
         flags:  0x00000041

Unfortunately there is no per cpu information about the VECTOR domain (yet).

The irqs directory contains detailed information about mapped interrupts.

# cat /sys/kernel/debug/irq/irqs/3
handler:  handle_edge_irq
status:   0x00004000
istate:   0x00000000
ddepth:   1
wdepth:   0
dstate:   0x01018000
            IRQD_IRQ_DISABLED
            IRQD_SINGLE_TARGET
            IRQD_MOVE_PCNTXT
node:     0
affinity: 0-143
effectiv: 0
pending:
domain:  IO-APIC-IR-0
hwirq:   0x3
chip:    IR-IO-APIC
  flags:   0x10
             IRQCHIP_SKIP_SET_WAKE
parent:
    domain:  INTEL-IR-3
     hwirq:   0x20000
     chip:    INTEL-IR
      flags:   0x0
     parent:
        domain:  VECTOR
         hwirq:   0x3
         chip:    APIC
          flags:   0x0

This was developed to simplify the debugging of the managed affinity
changes.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.537566163@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

genirq/irqdomain: Add map counter

Add a map counter instead of counting radix tree entries for
diagnosis. That also gives correct information for linear domains.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.459397746@linutronix.de

PCI/vmd: Create named irq domain

Use the fwnode to create a named domain so diagnosis works.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.379861978@linutronix.de

x86/msi: Create named irq domains

Use the fwnode to create named irq domains so diagnosis works.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.299024560@linutronix.de

x86/msi: Remove unused remap irq domain interface

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.221049665@linutronix.de

iommu/amd: Use named irq domain interface

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Joerg Roedel <joro@8bytes.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: iommu@lists.linux-foundation.org
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.142270582@linutronix.de

iommu/vt-d: Use named irq domain interface

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Joerg Roedel <joro@8bytes.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: iommu@lists.linux-foundation.org
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.063083997@linutronix.de

x86/msi: Provide new iommu irqdomain interface

Provide a new interface for creating the iommu remapping domains, so that
the caller can supply a name and a id in order to create named irqdomains.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: iommu@lists.linux-foundation.org
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235443.986661206@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

x86/uv: Create named irq domain

Use the fwnode to create a named domain so diagnosis works.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235443.907511074@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

x86/htirq: Create named domain

Use the fwnode to create a named domain so diagnosis works.

Mark the init function __init while at it.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235443.829047007@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

x86/ioapic: Create named irq domain

Use the fwnode to create a named domain so diagnosis works, but only when
the the ioapic is not device tree based.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235443.752782603@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

x86/vector: Create named irq domain

Use the fwnode to create a named domain so diagnosis works.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235443.673635238@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

genirq: Allow fwnode to carry name information only

In order to provide proper debug interface it's required to have domain
names available when the domain is added. Non fwnode based architectures
like x86 have no way to do so.

It's not possible to use domain ops or host data for this as domain ops
might be the same for several instances, but the names have to be unique.

Extend the irqchip fwnode to allow transporting the domain name. If no node
is supplied, create a 'unknown-N' placeholder.

Warn if an invalid node is supplied and treat it like no node. This happens
e.g. with i2 devices on x86 which hand in an ACPI type node which has no
interface for retrieving the name.

[ Folded a fix from Marc to make DT name parsing work ]

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235443.588784933@linutronix.de

genirq/msi: Prevent overwriting domain name

Prevent overwriting an already assigned domain name. Remove the extra check
for chip->name, because if domain->name is NULL overwriting it with NULL is
not a problem.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235443.510684976@linutronix.de

iommu/vt-d: Add name to irq chip

Add the missing name, so debugging will work proper.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Joerg Roedel <joro@8bytes.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: iommu@lists.linux-foundation.org
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235443.431939968@linutronix.de

iommu/amd: Add name to irq chip

Add the missing name, so debugging will work proper.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Joerg Roedel <joro@8bytes.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: iommu@lists.linux-foundation.org
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235443.343236995@linutronix.de

x86/apic: Add name to irq chip

Add the missing name, so debugging will work proper.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235443.266561988@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

dt-bindings/interrupt-controller: Add DT binding for the Marvell GICP

This commit adds the Device Tree binding documentation for the Marvell
GICP, an extension to the GIC that allows to trigger GIC SPI interrupts
using memory transactions. It is used by the ICU unit in the Marvell
CP110 block to turn wired interrupts inside the CP into SPI interrupts
at the GIC level in the AP.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/qcom: Use builtin_platform_driver to simplify the code

Use the builtin_platform_driver() macro to make the code simpler.

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/aspeed-i2c-ic: Add I2C IRQ controller for Aspeed

The Aspeed 24XX/25XX chips share a single hardware interrupt across 14
separate I2C busses. This adds a dummy irqchip which maps the single
hardware interrupt to software interrupts for each of the busses.

Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/aspeed-i2c-ic: Add binding docs for Aspeed I2C Interrupt Controller

Added device tree binding documentation for Aspeed I2C Interrupt
Controller.

Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/aspeed-vic: Add AST2500 compatible string

In addition to introducing the new compatible string the bindings
description is reworked to be more generic.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/aspeed-vic: Constify irq_domain_ops

struct irq_domain_ops is not modified, so it can be made const.

Cc: Joel Stanley <joel@jms.id.au>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Revert "irqchip/armada-370-xp: Fix regression by clearing IRQ_NOAUTOEN"

This reverts commit 353d6d6c82e5d2533ba22e7f9fb081582bf50dc2, which is
no longer needed, now that the irq-armada-370-xp driver properly
re-enables per-CPU interrupt on both the boot CPU and secondary CPUs
after resume.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/armada-370-xp: Re-enable per-CPU interrupts at resume time

Commit d17cab4451df1 ("irqchip: Kill off set_irq_flags usage") changed
the code of armada_370_xp_mpic_irq_map() from using set_irq_flags() to
irq_set_probe().

While the commit log seems to imply that there are no functional
changes, there are indeed functional changes introduced by this commit:
the IRQ_NOAUTOEN flag is no longer cleared. This functional change
caused a regression on Armada XP, which no longer works properly after
suspend/resume because per-CPU interrupts remain disabled. This
regression was temporarly worked around in commit
353d6d6c82e5d ("irqchip/armada-370-xp: Fix regression by clearing
IRQ_NOAUTOEN"), but it is not the most satisfying solution. This commit
implements the solution that was initially discussed with Thomas
Gleixner.

Due to how the hardware registers work, the irq-armada-370-xp cannot
simply save/restore a bunch of registers at suspend/resume to make sure
that the interrupts remain in the same state after resuming. Therefore,
it relies on the kernel to say whether the interrupt is disabled or not,
using the irqd_irq_disabled() function. This was all working fine while
the IRQ_NOAUTOEN flag was cleared.

With the change introduced by Rob Herring in d17cab4451df1, the
IRQ_NOAUTOEN flag is now set for all interrupts. irqd_irq_disabled()
returns false for per-CPU interrupts, and therefore our per-CPU
interrupts are no longer re-enabled after resume.

This commit fixes that by using irqd_irq_disabled() only for global
interrupts, and using the newly introduced irq_percpu_is_enabled() for
per-CPU interrupts.

Also, it fixes a related problems that per-CPU interrupts were only
re-enabled on the boot CPU and not other CPUs. Until now this wasn't a
problem since on this platform, only the local timers are using per-CPU
interrupts and the local timers of secondary CPUs are turned off/on
during CPU hotplug before suspend, after after resume. However, since
Linux 4.4, we are also be using per-CPU interrupts for the network
controller, so we need to properly restore the per-CPU interrupts on
secondary CPUs as well.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/armada-370-xp: Document the overall driver logic

Since the overall logic of the driver to handle the global and per-CPU
masking of the interrupts is far from trivial, this commit adds a long
comment detailing how the hardware operates and what strategy the
driver implements on top of that.

Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/armada-370-xp: Re-order register definitions

In order to clarify to which register base the various register
definitions apply, this commit re-orders them, and adds a comment that
clearly indicate which registers are relative to "main_int_base" and
which registers are relative to "per_cpu_int_base".

Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/gicv3-its: Skip irq affinity setting when target cpu is the same as current setting

Just skip the irq affinity setting when the target cpu is the same as
current setting.
This is a small optimization for irq affinity setting logic.

Signed-off-by: MaJun <majun258@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/gic-v3-its: Fix MSI alias accounting

The call to pci_for_each_dma_alias() in the ITS PCI code has aroused
suspicion in the past, and upon closer inspection does turn out to be
completely backwards. Rather than iterating through each RID alias of
the given device, what we actually want to be doing here is iterating
through all the *other* devices which may also alias the same RID, in
order to size the table for the worst case.

Do the right thing by ignoring the initial DMA aliases themselves and
just using that walk to detect an aliasing bridge, then walking back
down the bus topology as necessary to actually count everything else.

Our alias handling still isn't perfect, since we don't account for the
cases of certain bridges only taking ownership of transactions under
particular circumstances, but without completely reworking the ITS code
to cope with the notion of multiple DevIDs per device, it'll have to do.

Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/irq-renesas-h8s: Constify irq_domain_ops

struct irq_domain_ops is not modified, so it can be made const.

Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/irq-renesas-h8300h: Constify irq_domain_ops

struct irq_domain_ops is not modified, so it can be made const.

Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/irq-mips-gic: Constify irq_domain_ops

struct irq_domain_ops is not modified, so it can be made const.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/irq-mbigen: Constify irq_domain_ops

struct irq_domain_ops is not modified, so it can be made const.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/irq-imx-gpcv2: Constify irq_domain_ops

struct irq_domain_ops is not modified, so it can be made const.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/i8259: Constify irq_domain_ops

struct irq_domain_ops is not modified, so it can be made const.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/sunxi-nmi: Support sun6i-a31-r-intc compatible

The R_INTC on the A31 is undocumented. It was previously supported
by the sun6i-a31-sc-nmi compatible. This compatible however required
the register region to start at the first used register, rather than
the boundaries laid out in the SoC's memory map. The new compatible
fixes the alignment, while also naming it properly.

Since the only difference between the old and new compatibles are
a fixed offset for the registers, and since the old one is deprecated,
this patch adds a set of register defines for the new compatible,
while modifying the old set to reference the new set minus a fixed
offset.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

dt-bindings/interrupt-controller: sunxi-nmi: Add compatible for A31 R_INTC

The A31 and later have an R_INTC block which handles the NMI interrupt
pin on the SoC. This interrupt pin is used by the external PMIC to
signal interrupts to the SoC.

While this hardware block is undocumented, the interrupt offsets
combined with the register regions for the existing "sun6i-a31-sc-nmi"
compatible line up with the old interrupt controller found on the A10.
Experiments show that only the first 32 interrupt lines can be enabled,
and only the first (NMI) interrupt is actually connected.

This patch adds a new, properly named compatible for the A31 R_INTC
block, which requires the register region to be properly aligned to
the block boundary. For comparison, the old "sun6i-a31-sc-nmi"
compatible had its register region aligned with the first used
register. This didn't match up with the memory map in the SoC's
datasheet/user manual.

Since the new compatible supercedes the old one, deprecate the old one.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/sunxi-nmi: Const-ify sunxi_sc_nmi_reg_offs structures

The sunxi_sc_nmi_reg_offs, which hold the register offsets for the
various variants, is never modified, and only used at init time within
the init functions referenced by IRQCHIP_DECLARE, which themselves are
tagged __init.

Const-ify the sunxi_sc_nmi_reg_offs structures, and tag them as
__initconst.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/sunxi-nmi: Reorder sunxi_sc_nmi_reg_offs' in ascending order

This is a pure code move to reorder the various sunxi_sc_nmi_reg_offs'
by family and alphabetical order. No functionality changes.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/sunxi-nmi: Document interrupt disabling and clearing at probe time

The sunxi-nmi disables all its interrupts and clears any pending
interrupts at probe time.

Add comments documenting it, just to make it clear.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irqchip/sunxi-nmi: Convert magic numbers to defines

The sunxi-nmi driver has a bunch of raw register offsets and bit values.

Convert them into define macros for better readability.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

irq/generic-chip: Provide devm_irq_setup_generic_chip()

Provide a resource managed variant of irq_setup_generic_chip().

Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Link: http://lkml.kernel.org/r/1496246820-13250-6-git-send-email-brgl@bgdev.pl

irq/generic-chip: Provide devm_irq_alloc_generic_chip()

Provide a resource managed variant of irq_alloc_generic_chip().

Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Link: http://lkml.kernel.org/r/1496246820-13250-5-git-send-email-brgl@bgdev.pl

irq/generic-chip: Export irq_init_generic_chip() locally

This function will be used in the devres variant of
irq_alloc_generic_chip().

Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Link: http://lkml.kernel.org/r/1496246820-13250-4-git-send-email-brgl@bgdev.pl

irq/generic-chip: Provide irq_destroy_generic_chip()

Most users of irq_alloc_generic_chip() call irq_setup_generic_chip()
too. To simplify the cleanup provide a function that both removes a
generic chip and frees its memory.

Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Link: http://lkml.kernel.org/r/1496246820-13250-3-git-send-email-brgl@bgdev.pl

irq/generic-chip: Provide irq_free_generic_chip()

Currently there's no way for users of irq_alloc_generic_chip() to free
the allocated memory other than calling kfree() manually on the
returned pointer. This may lead to errors if the internals of
irq_alloc_generic_chip() ever change. Provide a routine to free the
generic chip.

Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Link: http://lkml.kernel.org/r/1496246820-13250-2-git-send-email-brgl@bgdev.pl

Merge branch 'linus' into irq/core

Get upstream changes so pending patches won't conflict.

mm: larger stack guard gap, between vmas

Stack guard page is a useful feature to reduce a risk of stack smashing
into a different mapping. We have been using a single page gap which
is sufficient to prevent having stack adjacent to a different mapping.
But this seems to be insufficient in the light of the stack usage in
userspace. E.g. glibc uses as large as 64kB alloca() in many commonly
used functions. Others use constructs liks gid_t buffer[NGROUPS_MAX]
which is 256kB or stack strings with MAX_ARG_STRLEN.

This will become especially dangerous for suid binaries and the default
no limit for the stack size limit because those applications can be
tricked to consume a large portion of the stack and a single glibc call
could jump over the guard page. These attacks are not theoretical,
unfortunatelly.

Make those attacks less probable by increasing the stack guard gap
to 1MB (on systems with 4k pages; but make it depend on the page size
because systems with larger base pages might cap stack allocations in
the PAGE_SIZE units) which should cover larger alloca() and VLA stack
allocations. It is obviously not a full fix because the problem is
somehow inherent, but it should reduce attack space a lot.

One could argue that the gap size should be configurable from userspace,
but that can be done later when somebody finds that the new 1MB is wrong
for some special case applications. For now, add a kernel command line
option (stack_guard_gap) to specify the stack gap size (in page units).

Implementation wise, first delete all the old code for stack guard page:
because although we could get away with accounting one extra page in a
stack vma, accounting a larger gap can break userspace - case in point,
a program run with "ulimit -S -v 20000" failed when the 1MB gap was
counted for RLIMIT_AS; similar problems could come with RLIMIT_MLOCK
and strict non-overcommit mode.

Instead of keeping gap inside the stack vma, maintain the stack guard
gap as a gap between vmas: using vm_start_gap() in place of vm_start
(or vm_end_gap() in place of vm_end if VM_GROWSUP) in just those few
places which need to respect the gap - mainly arch_get_unmapped_area(),
and and the vma tree's subtree_gap support for that.

Original-patch-by: Oleg Nesterov <oleg@redhat.com>
Original-patch-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
"Stream of fixes has slowed down, only a few this week:

   - Some DT fixes for Allwinner platforms, and addition of a clock to
     the R_CCU clock controller that had been missed.

   - A couple of small DT fixes for am335x-sl50"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: allwinner: a64: Add PLL_PERIPH0 clock to the R_CCU
  ARM: sunxi: h3-h5: Add PLL_PERIPH0 clock to the R_CCU
  ARM: dts: am335x-sl50: Fix cannot claim requested pins for spi0
  ARM: dts: am335x-sl50: Fix card detect pin for mmc1
  arm64: allwinner: h5: Remove syslink to shared DTSI
  ARM: sunxi: h3/h5: fix the compatible of R_CCU