ath9k: set diversity group for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add fast_div_bias configuration for diversity group 1

The patch adds the missing configuration code for diversity
group 1.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove superfluous parentheses

Also remove two empty lines.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix antenna diversity configuration for non AR9485 chips

The current values must be used only on AR9485 chips. Other chips
requires different values.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add a missing case statement to ath_ant_div_comb_alt_check

The 'ar9003_hw_antdiv_comb_conf_get' function sets div_group to 2
however that value is not used in 'ath_ant_div_comb_alt_check'.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use correct max_streams for AR9330

The AR9330 is a single stream chip.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: enable antenna diversity for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: set NF limits for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: configure xpa bias level for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use correct EEPROM base for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: enable tuning capacitance configuration for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: skip internal regulator configuration for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: enable TX/RX data byte swap for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: configure RF channel frequency for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix channel frequency calculation for AR9340

A multiplication is missing from the current formula.

Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: read spur frequency information from eeprom for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: don't enable LDPC for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use different BB watchdog timeout value for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add AR9330 specific PLL initialization

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: initialize rx gain table for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: initialize tx gain table for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: initialize mode registers for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add AR9330 initvals

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add platform device id for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add MAC revision detection for AR9330

The AR9330 1.0 and 1.1 are using the same revision,
thus it is not possible to distinguish the two chips.
The platform setup code can distinguish the chips based
on the SoC revision.

Add a callback function to ath9k_platform_data in order
to allow getting the revision number from the platform code.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: define device id for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: define mac version for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix calculation of PAPRD training power at 5Ghz

higher the chainmask, lesser the power_delta to be added
to the paprd_training_power

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: use netlink consistent dump feature for BSS dumps

Use the new consistent dump feature from (generic) netlink
to advertise when dumps are incomplete.

Readers may note that this does not initialize the
rdev->bss_generation counter to a non-zero value. This is
still OK since the value is modified only under spinlock
when the list is modified. Since the dump code holds the
spinlock, the value will either be > 0 already, or the
list will still be empty in which case a consistent dump
will actually be made (and be empty).

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove casts of void pointers

In some cases local pointers are used to cast void pointers passed to
the function. Those unnecessary local pointers are also removed.

This patch was inspired by Joe Perches' patch
[PATCH net-next 1/2] wireless: Remove casts of void *;
and the comments from Julian Calaby.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Cc: Joe Perches <joe@perches.com>
Cc: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: detect stalled beacon interrupt faster

As USB_INT_ID_RETRY_FAILED can override USB_INT_ID_REGS, beacon interrupt
(CR_INTERRUPT) might be lost. Problem is that when device trigger CR_INTERRUPT
it disables HW interrupt. Now if USB_INT_ID_REGS with CR_INTERRUPT gets lost,
beacon interrupt stays disabled until beacon watchdog notices the stall. This
happen very often on heavy TX. Improve watchdog to trigger earlier, after three
missing beacon interrupts.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: don't let zd_mac_config_beacon() run too long from beacon interrupt handler

zd_mac_config_beacon() has only limited time to set up beacon when called from
beacon interrupt handler/worker. So do not let it retry acquiring beacon fifo
semaphore in interrupt handler. Beacon fifo semaphore should not be locked by
firmware anyway at this time, it's only locked when device is using/txing
beacon.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: handle lost read-reg interrupts

Device losses read-reg interrupts. By looking at usbmon it appears that
USB_INT_ID_RETRY_FAILED can override USB_INT_ID_REGS. This causes read
command to timeout, usually under heavy TX.

Fix by retrying read registers again if USB_INT_ID_RETRY_FAILED is received
while waiting for USB_INT_ID_REGS.

However USB_INT_ID_REGS is not always lost but is received after
USB_INT_ID_RETRY_FAILED and is usually received by the retried read
command. USB_INT_ID_REGS of the retry is then left unhandled and might
be received by next read command. Handle this by ignoring previous
USB_INT_ID_REGS that doesn't match current read command request.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: only update HW beacon if new beacon differs from currect

Update HW beacon only when needed. This appears to make device work in AP-mode
(dtim_period=1) somewhat more stable.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: make 'handle_rx_packet: invalid, small RX packet' message debug-only

This message is should be debug-only as it tells almost nothing useful. It also
happens very often and just floods logs.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: fix invalid signal values from device

Driver uses IEEE80211_HW_SIGNAL_UNSPEC and so signal values reported to
mac80211 should be in range 0..100. Sometimes device return out of range
values. These out of range values can then trigger warning in
cfg80211_inform_bss_frame.

This patch adds checks to enforce range returned from driver to
mac80211 be in 0..100 range.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

netlink: advertise incomplete dumps

Consider the following situation:
 * a dump that would show 8 entries, four in the first
   round, and four in the second
 * between the first and second rounds, 6 entries are
   removed
 * now the second round will not show any entry, and
   even if there is a sequence/generation counter the
   application will not know

To solve this problem, add a new flag NLM_F_DUMP_INTR
to the netlink header that indicates the dump wasn't
consistent, this flag can also be set on the MSG_DONE
message that terminates the dump, and as such above
situation can be detected.

To achieve this, add a sequence counter to the netlink
callback struct. Of course, netlink code still needs
to use this new functionality. The correct way to do
that is to always set cb->seq when a dumpit callback
is invoked and call nl_dump_check_consistent() for
each new message. The core code will also call this
function for the final MSG_DONE message.

To make it usable with generic netlink, a new function
genlmsg_nlhdr() is needed to obtain the netlink header
from the genetlink user header.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: calibrate radio after switching channel

After uploading radio values calibration goes in. In MMIO dump it is:
 radio_read(0x002b) -> 0x0008
radio_write(0x002b) <- 0x0008
 radio_read(0x002e) -> 0x0004
radio_write(0x002e) <- 0x0000
 radio_read(0x002e) -> 0x0000
radio_write(0x002e) <- 0x0004
 radio_read(0x002b) -> 0x0008
radio_write(0x002b) <- 0x0009
To find masks and sets, MMIO hacks were used to fool closed driver.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: reset usb devices at probe

When module is reloaded, device may fail to work, with messages:

[  342.211926] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x0059, type=2.
[  342.314254] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x004a, type=2.
[  342.416458] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 3183 max 2432.
[  342.518605] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00c9, type=2.
[  342.620836] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00ae, type=1.
[  342.723201] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[  342.825399] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[  342.927624] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[  343.029804] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 2491 max 2432.
[  343.132008] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 2576 max 2432.
[  343.234326] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x004c, type=1.
[  343.438723] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00e6, type=1.

Whereas replugging device make it functional. To solve that problem
force reset device during probe.

With patch messages are gone. Unfortunately device may sometimes
still does not operate correctly after module reload (fail to receive
data after associate), but such cases are rarer than without the patch.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: fix possible memory corruption in case of invalid rxdesc.size

Sometimes rxdesc descriptor provided by hardware contains invalid
(random) data. For example rxdesc.size can be bigger than actual
size of the buffer. When this happen rt2x00crypto_rx_insert_iv()
corrupt memory doing memmove outside of buffer boundaries.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: move declarations of chantables functions to correct files

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: update switching analog on/off

Specs were recently updated.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: switch radio to requested channel

Switching channel happens after specific SHM write to B43_SHM_SH_CHAN.
This is the way we found it in BCM4331 MMIO dumps. By comparing with
N-PHY code we noticed there is routing used for SYN and TX/RX.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: add place for implementing channel switching

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: define standard structs for channel switching

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: enable radio

The trick was to find 0x810 PHY reg ops close to analog enabling code.
To find out proper masks and sets, MMIO hacks were used.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: implement killing radio

Closed drivers kill radio right after reading radio version and MACCTL,
so it was easy to find related PHY ops:
 phy_read(0x0810) -> 0x0000
phy_write(0x0810) <- 0x0000
To find out the mask of above OP, MMIO hack was used to fake read val:
 phy_read(0x0810) -> 0xffff
phy_write(0x0810) <- 0x0000

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of /linux/kernel/git/padovan/bluetooth-next-2.6

Bluetooth: Fix not setting the chan state

When the connection is ready we should set the connection
to CONNECTED so userspace can use it.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Merge /linux/kernel/git/padovan/bluetooth-2.6

Conflicts:
net/bluetooth/l2cap_core.c

rtlwifi: rtl8192{c,ce,cu,se}: Remove comparisons of booleans with true

These are a potential source of confusion, as most C code treats all
non-zero values as true.

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192cu: Remove unused parameter

rtl_ps_set_rf_state's protect_or_not parameter is not set to
true anywhere, except for commented out code.

It enables some legacy locking code, which is no longer used,
so delete the parameter and the old locking code.

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Fix typo in variable name

offchan_deley should be offchan_delay

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: clean exports of functions

Function managing IRQs is needed for external drivers like b43.
On the other side we do not expect writing any hosts drivers outside of
bcma, so this is safe to do not export functions related to this.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: add missing ieee80211_free_hw() on unload in AHB code

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: free sc->ah in ath5k_deinit_softc

Nothing else is freeing it, and this mirrors the error handling path
already in ath5k_init_softc.

https://bugzilla.kernel.org/show_bug.cgi?id=37592

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Tsyvarev Andrey <tsyvarev@ispras.ru>

bcma: fix BCM43224 rev 0 workaround

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: enable support for 14e4:4357 (BCM43225)

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: make sure PAPRD training is properly done

checking the status of PAPRD_AGC2_POWER(Log(ADC_power) measured after
last gain-change in dB) field suggests whether the PAPRD is completely/properly
done. This is an additional check apart from polling for PAPRD done bit being set.
        Susinder suggests that the ideal power range value should be
0xf0 to 0xfe. With AR9382 we do have the values in this range. to have a
common check for all platforms we take agc2_power should be atleast greater
than 0xe0

Cc: susinder@qca.qualcomm.com
Cc: senthilb@qca.qualcomm.com
Cc: kmuthusa@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix a corner case failure in sending PAPRD frames in HT40

when the AP is configured with HT40/2.4GHz and when PAPRD is enabled in station
we have PAPRD training frames never sent out because of the following
failure "PAPRD target power delta out of range". This consistently happens
in channel 10,11 in Over The Air testing and rarely in channel 6 under wired
setup.
        the reason behind this issue is all the HT40 rates target power
are 0 when we operate in channel 10/11 at 2.4GHz

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: quiesce vif before suspending

Cancel all relevant timers/works before suspending (wowlan).

This patch handles the following warning:
WARNING: at net/mac80211/util.c:565 queueing ieee80211 work while going to suspend
Backtrace:
[<bf07b598>] (ieee80211_can_queue_work+0x0/0x4c [mac80211])
[<bf07c28c>] (ieee80211_queue_work+0x0/0x30 [mac80211])
[<bf0690dc>] (ieee80211_sta_timer+0x0/0x3c [mac80211])
[<c00a3008>] (run_timer_softirq+0x0/0x220)
[<c009e530>] (__do_softirq+0x0/0x130)
[<c009e660>] (irq_exit+0x0/0xb4)
[<c004c4a0>] (ipi_timer+0x0/0x4c)
[<c0046350>] (do_local_timer+0x0/0x88)
[<c00488ec>] (cpu_idle+0x0/0xe0)
[<c05294e8>] (rest_init+0x0/0xe0)
[<c0008958>] (start_kernel+0x0/0x314)

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bluetooth: Remove useless access to the socket

We already have access to the chan, we don't have to access the
socket to get its imtu.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Fix crash when setting a LE socket to ready

We should not try to do any other type of configuration for
LE links when they become ready.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6

rtlwifi: include mac80211.h from core.h

core.h references ieee80211_ops but doesn't include mac80211.h, which issues
a warning once mac80211-compat.h is taken into use.

Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: include mac80211.h from zd_chip.h

zd_chip.h contains one function with a pointer to ieee80211_hw but doesn't
include mac80211.h. As a temporary solution include mac80211.h to avoid
a warning.

Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix stop/wake queue hacks

The hacks break once mac80211-compat.h is taken into use. Fix it by adding
an ifdef check.

Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: fix stop/wake queue hacks

The hacks break once mac80211-compat.h is taken into use. Fix it by adding
an ifdef check.

Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: remove incorrect define

Remove unused and incorrect EEPROM define

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: merge duplicate code into single function

Same operation needed by multiple devices, move to single function.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: code alignment

Code alignment, no functional changes.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: add offset define for subsystem id

Add offset define for subsystem id in EEPROM

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: Add power_level module parameter

Add power_level module parameter to set the default power save level.
Power save level has range from 1 - 5, default power save level is 1.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: add power_save module parameter

Add power_save module parameter to enable power management if needed
Default power management is disabled.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: store the irq number to iwl_bus just like dev

Since the irq number is just an unsigned int, store it inside iwl_bus
instead of calling the get_irq ops every time it is needed.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: warn about nested SYNC commands

Since there is no protection around SYNC host command mechanism, at least WARN
when collision happens between two SYNC host comamnds. I am not sure there is a
real  issue (beyond the HCMD_ACTIVE flag maintenance) with having two SYNC host
commands at the same time, but at least now, we will know about it.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: fix misplaced bracket

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: waterfall the bus level if prepare card failed

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: finally kill the pointer to pci_dev from iwl-dev.h

All pci related stuff is in iwl-pci.c.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: add a get_irq method to iwl_bus_ops and use it

In order to remove a few more dereference to priv->pdev that will be killed
[Asoon, there is now a method to get the IRQ number.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: don't read the PCI_REVISION_ID from iwl-agn.c

The PCI_REVISION_ID is read and printed in iwl_pci_probe anyway using pr_info

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: add a method to get the HW ID description as a string to iwl_bus_ops

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: move PCI power related functions to the PCI layer

Continue to popule the PCI layer and the iwl_bus_ops with the power related
stuff.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: don't use the PCI wrappers for DMA operation

Get a pointer to the struct device during probe and get the rid of all the PCI
specific DMA wrappers.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: move PCI related operations from probe and remove to PCI layer

Since we have now a PCI layer, all the init and deinit code that is PCI
related should move to there.

Also move the IO functions: read8/read32/write32. They need hw_base which
is killed from priv.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: add get_dev to iwl_bus_ops

Bus specific layer must know how to return the struct device* of the device.
Implement that as a callback of iwl_bus_ops and use that callback instead of
using the priv->pdev pointer which is meant to disappear soon.

Since the struct device * is needed in hot path, iwl_bus holds a pointer to it
instead of calling get_dev all the time.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: introduce iwl_bus and iwl_bus_ops

iwl_bus will represent a bus, and iwl_bus_ops all the operations that can be
done on this bus.
For the moment only set_prv_data is implemented. More to come...

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: remove uneeded include to pci.h and dma_mapping.h from a few files

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: add a iwl_pci.[ch] files that will contain all PCI specific code

Move some PCI functionality to the new iwl_pci.[ch] files:
* the PCI_DEVICE_TABLE
* the pci_driver struct definition
* the PCI probe / remove functions
* the PCI suspend / resume functions

All these functions are now split: the trigger comes from the PCI layer which
calls to the bus generic code located in the other files.

This is the beginning only. There are still a lot of PCI related code needs
to be gathered.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: don't disable interrupts after the NIC has been reset

It is superfluous to disable the interrupts after we reset the NIC. The only
entity that could enable the interrupts after the NIC is reset is the driver.
So remove this pointless action.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: Support flush queues for specified interface

Flush command can target specified interface or all interfaces

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: add PAN to tx flush

When issue tx flush, also consider PAN

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: Remove un-necessary indirect call

After driver split, no need to make indirect call to txfifo flush function

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Bluetooth: Fix locking in blacklist code

There was no unlock call on the errors path

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

b43: HT-PHY: implement switching analog

Turning it on is always done between reading PHY version and radio
version, so it was easy to find it in MMIO dumps from ndiswrapper.
Turning off is done by writing different values to the same registers.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: implement radio ops

Every PHY has some specific bit used for reading radio regs. Analyze of
MMIO dumps from BCM4331 and ndiswrapper has shown it is 0x200 for HT.
 radio_read(0x037f) -> 0x0073
radio_write(0x017f) <- 0x0072

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: annotate reg in ath5k_hw_nic_reset() as __iomem

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: minor cleanup

Move an extern variable declaration to a header file.  Prefix all
functions with "ath5k_".  Make ath5k_intr() static.  Remove unneeded
forward declarations.  Remove pointless "extern" in a function
declaration.

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: typo fix in a comment

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use standard max(), remove A_MAX macro

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>