Andrew Cameron [Wed, 26 Jun 2019 21:40:54 +0000 (16:40 -0500)]
ath79: add support for TP-Link CPE510-v2/v3
TP-Link CPE510-v2/v3 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- Based on the same underlying hardware as the TP-Link CPE510
- Power, LAN, and 4 green LEDs
- 1 10/100Mbps Shielded Ethernet Port (Passive PoE in)
- Built-in 13dBi 2x2 dual-polarized directional MIMO antenna
- Adjustable transmission power from 0 to 23dBm/200mw
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[whitespace fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Pramod Pancha [Fri, 5 Jul 2019 17:45:19 +0000 (13:45 -0400)]
ath79: add support for Trendnet TEW-823DRU
Trendnet TEW-823DRU is a dual-band AC1750 router.
The router is based on Qualcomm/Atheros QCA9558 + QCA9880.
Specification:
720 MHz CPU
256 MB of RAM
16 MB of FLASH
3T3R 2.4 GHz
3T3R 5 GHz
5x 10/100/1000 Mbps Ethernet
Firmware can be flashed from the web interface. Tested on 3 routers
with no issues.
Signed-off-by: Pramod Pancha <pancha@vill.com>
[whitespace fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Christoph Krapp [Tue, 16 Jul 2019 18:47:49 +0000 (20:47 +0200)]
ath79: add support for TP-Link RE355 v1 and RE450 v1
Specification:
SoC: Qualcomm Atheros QCA9558
RAM: 64/128MiB
Flash: 8MiB SPI-NOR
Wifi:
- 2.4GHz: 3T3R (QCA9558)
- 5GHz: 3T3R (QCA9880)
LAN: 1x 10/100/1000 Mbps
UART:
- TP1: Tx
- TP2: Rx
- TP3: Gnd
- TP4: 3v3
Flash instructions:
Flash factory image through stock firmware WEB UI.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
Georgi Vlaev [Wed, 17 Apr 2019 18:17:45 +0000 (21:17 +0300)]
ramips: add support for TP-Link RE650 v1
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
Petr Štetiar [Wed, 17 Jul 2019 21:04:22 +0000 (23:04 +0200)]
mtd: cleanup unused code and variables in fis.c
While compile checking mtd changes in PR#1359 I've noticed following
compiler warnings and cleaned them up:
fis.c: In function 'fis_remap':
fis.c:143:25: warning: variable 'redboot' set but not used [-Wunused-but-set-variable]
struct fis_image_desc *redboot = NULL;
^~~~~~~
fis.c:142:25: warning: variable 'fisdir' set but not used [-Wunused-but-set-variable]
struct fis_image_desc *fisdir = NULL;
^~~~~~
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Daniel Gimpelevich [Sat, 1 Sep 2018 02:28:35 +0000 (19:28 -0700)]
ath79: add support for Bluesocket BSAP1880 board
This board was used in dual-band 802.11n enterprise access points, models
BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was
acquired by Adtran in 2011, who has now EOL'ed them. They differed only in
that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were
inside the case. They have an external RJ-45 console port, which works with
standard Cisco 72-3383-01 console cables.
Specification:
- System-On-Chip: AR7161
- CPU/Speed: 600 MHz
- Flash-Chip: Macronix MX25L12845E
- Flash size: 16 MiB
- RAM: 64 MiB
- Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn
- Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an
- PHY: Vitesse VSC8601, Rev. B
Installation:
1. Connect to the serial console using a terminal that supports YMODEM at
115200 bps, 8 data bits, no parity, 1 stop bit
2. Interrupt the bootloader using its password, which is: r00t
3. Issue the "fis init" command, confirming if prompted
4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin
file, and substitute it below, instead of where I have "LeNgTh"
5. Issue the following command, and upload this file using YMODEM protocol
load -r -v -b 0x80060000 -m ymodem
6. Issue the following commands, substituting as mentioned above:
fis create -b 0x80060000 -l LeNgTh vmlinux_2
load -r -v -b 0x80100000 -m ymodem
7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin
8. Issue the "fis free" command, and for the first range in its response,
use a hexadecimal calculator to subtract the start from the end in order
to substitute it below, with the leading "0x" to specify it in
hexadecimal, instead of where I have "LeNgTh"
9. Issue the following commands, substituting as mentioned above:
fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs
reset
10.Wait for the status LED to go solid green
Tested-by: Brian Gonyer <bgonyer@gmail.com>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[fixed obsolete $ARGV in platform_do_upgrade]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Daniel Gimpelevich [Wed, 26 Jun 2019 19:56:47 +0000 (12:56 -0700)]
ath79: widen RedBoot directory search and add PHY
The Bluesocket BSAP1880 board has a Vitesse PHY, for which the driver was
not being included, and its RedBoot directory block is earlier in the
flash than the search was allowing. This commit prepares for supporting it.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Daniel Gimpelevich [Wed, 26 Jun 2019 19:39:37 +0000 (12:39 -0700)]
ath79: support "rgmii-id" PHY mode in ag71xx
The ag71xx code did not include a case for the "rgmii-id" PHY mode in the
code. There are devices that need this mode, so I'm adding it.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Daniel Gimpelevich [Sat, 1 Sep 2018 01:14:24 +0000 (18:14 -0700)]
mtd: add CRC signature to RedBoot partition map
The code for calculating the CRC32 signatures for RedBoot FIS partitions
was already included, but for unknown reasons, it was never invoked. Some
bootloaders enforce checking these for loaded kernels, so they should be
written. This patch does so.
Tested-by: Brian Gonyer <bgonyer@gmail.com>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Martin Schiller [Tue, 28 May 2019 10:50:15 +0000 (12:50 +0200)]
openvpn: add new list option tls_ciphersuites
To configure the list of allowable TLS 1.3 ciphersuites, the option
tls_ciphersuites is used instead of tls_ciphers.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Zachary Cook [Thu, 11 Jul 2019 20:09:15 +0000 (16:09 -0400)]
brcm47xx: fix 831-old_gpio_wdt.patch for linux 4.19
Fix the following compilation error when using linux 4.19 on brcm47xx:
drivers/watchdog/old_gpio_wdt.c:236:2: error: implicit declaration of function 'setup_timer'
setup_timer was removed and replaced by timer_setup in linux >=4.15:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=
513ae785
Update the patch to use the timer_setup interface
Signed-off-by: Zachary Cook <zachcook1991@gmail.com>
Petr Štetiar [Wed, 17 Jul 2019 13:19:54 +0000 (15:19 +0200)]
ath79: ar9330: add missing watchdog node
It was reported in FS#2385, that Carambola2 doesn't currently have
working watchdog so fix it by adding watchdog node.
Ref: FS#2385
Signed-off-by: Petr Štetiar <ynezz@true.cz>
INAGAKI Hiroshi [Thu, 27 Jun 2019 03:27:27 +0000 (12:27 +0900)]
ramips: add MT7615 wireless support for ELECOM WRC-1167GHBK2-S
ELECOM WRC-1167GHBK2-S has a MediaTek MT7615D chip for 2.4/5 GHz
wireless.
A driver package for MT7615 chip is added to OpenWrt in
a0e5ca4f3523b9eef96bff32e45f6fa8275b982f,
so add preliminary MT7615 chip support for WRC-1167GHBK2-S.
Note: Currently, DBDC mode for MT7615 is not supported in mt76 driver.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Petr Štetiar [Tue, 16 Jul 2019 19:43:08 +0000 (21:43 +0200)]
perf: simplify the build process
Redirect the build output to PKG_BUILD_DIR instead of copying over
complete source code.
Build tested on following targets:
x86/64 ar7/generic ipq40xx/generic imx6/generic ar71xx/generic
ramips/mt7621 ramips/mt7620 sunxi/cortexa7
Run tested on imx6/apalis.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Tue, 16 Jul 2019 19:46:49 +0000 (21:46 +0200)]
kernel: generic: fix perf build breakage on 4.19
Drop 211-host_tools_portability.patch which is breaking perf build on
4.19 kernels by removing the include directory from the host's CFLAGS
leading to the following build breakage:
pmu-events/jevents.c:48:10: fatal error: linux/list.h: No such file or directory
#include <linux/list.h>
^~~~~~~~~~~~~~
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Tue, 16 Jul 2019 20:06:40 +0000 (22:06 +0200)]
imx6: apalis: add missing jffs2reset to ramfs during sysupgrade
jffs2reset is used to cleanup the rootfs_data overlay, but it's
currently missing in the ramfs during sysupgrade leading to the
following error:
Switching to ramdisk...
Performing system upgrade...
/lib/upgrade/do_stage2: line 27: jffs2reset: not found
Fixes: 2f1a11d0089c ("imx6: apalis: fix config survival after sysupgrade -n")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Tue, 16 Jul 2019 08:23:18 +0000 (10:23 +0200)]
imx6: apalis: fix sysupgrade paths
We can't use $board_name in sysupgrade paths for kernel and rootfs as we
currently generate one image which could be used on two different base
boards.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Alberto Bursi [Sun, 14 Jul 2019 01:11:00 +0000 (03:11 +0200)]
x86: add modern network modules to Generic target
Many Atom-based embedded/industrial x86 boards can't run 64bit operating
systems due to either processor or board firmware limitations, but they
have modern interfaces (PCIe) or have modern Intel gigabit controllers
onboard. With the current default package selection for x86 Generic
target their network won't work.
Add the modern gigabit network modules needed or most likely going to be
used as add-in cards, similar to what is the list on x86_64 target.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Felix Fietkau [Wed, 17 Jul 2019 07:36:33 +0000 (09:36 +0200)]
mt76: update to the latest version
3d7f738 mt76: mt7615: add missing register initialization
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 19 Jun 2019 10:32:20 +0000 (12:32 +0200)]
mac80211: add config tweak for tx bursting when using VHT
By default, set BE tx queue TXOP limit to 1.0 in the hostapd config
Many vendor drivers are doing similar things to boost throughput.
On MT7612 under ideal conditions, it improves tx throughput from 470 Mbit/s
to about 570 Mbit/s.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rafał Miłecki [Sun, 14 Jul 2019 17:00:00 +0000 (19:00 +0200)]
base-files: don't set ARGV and ARGC
Those are not used by any image check function anymore.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Sun, 14 Jul 2019 16:59:59 +0000 (18:59 +0200)]
mvebu: sysupgrade: don't use $ARGV in platform_check_image()
sysupgrade passes image path to platform_check_image() as an argument so
it can be simply accessed using $1
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Sun, 14 Jul 2019 17:03:19 +0000 (19:03 +0200)]
treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()
stage2 passes image path to platform_do_upgrade() as an argument so it
can be simply accessed using $1
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Fri, 12 Jul 2019 12:05:49 +0000 (14:05 +0200)]
ramips: get rid of platform_pre_upgrade()
The only step between platform_pre_upgrade() and platform_do_upgrade()
is switching to ramdisk. It should be fine to "mtd erase firmware" from
the later callback and get rid of the first one.
This change wasn't tested on affected target but identical code logic
was verified to work as expected on brcm47xx with initramfs firmware.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Fri, 12 Jul 2019 12:05:47 +0000 (14:05 +0200)]
ar71xx: get rid of platform_pre_upgrade()
The only step between platform_pre_upgrade() and platform_do_upgrade()
is switching to ramdisk. It should be fine to "mtd erase firmware" from
the later callback and get rid of the first one.
This change wasn't tested on affected target but identical code logic
was verified to work as expected on brcm47xx with initramfs firmware.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Etienne Champetier [Sun, 14 Jul 2019 02:43:28 +0000 (19:43 -0700)]
ar71xx: enable SGMII fixup on Mikrotik wAP AC
fixes intermittent loss of connectivity on 1Gbit port, with log message:
> 803x_aneg_done: SGMII link is not ok
Thanks to David Bauer for pointing me in the right direction.
I just had to figure out the right bus_id, which you find in this log:
> ag71xx ag71xx.1: connected to PHY at gpio-1:00 [uid=
004dd074,
driver=Atheros 8031 ethernet]
Fixes FS#2236
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
[Wrapped commit message - Fixed whitespace erors]
Signed-off-by: David Bauer <mail@david-bauer.net>
Chuanhong Guo [Tue, 16 Jul 2019 11:38:27 +0000 (19:38 +0800)]
ath79: add seama header fixup for Qihoo C301
This script is copied from ar71xx. Without a header fixup, u-boot
checksum for kernel will fail after the first boot.
Fixes: a9360452f0 ("ath79: add support for Qihoo C301")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Tue, 16 Jul 2019 11:35:12 +0000 (19:35 +0800)]
package: mtd: add fixseama command for ath79
This is needed by Qihoo C301.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Rafał Miłecki [Sun, 14 Jul 2019 20:11:40 +0000 (22:11 +0200)]
orion: sysupgrade: change platform_check_image() args validation
sysupgrade passes image to check as argument so use $# instead of $ARGC.
It also fits this function better as it checks $1 and not $ARGV.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Sun, 14 Jul 2019 20:08:58 +0000 (22:08 +0200)]
mvebu: sysupgrade: drop platform_copy_config_sdcard() argument
That function doesn't take any arguments so don't pass anything when
calling it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Adrian Schmutzler [Mon, 15 Jul 2019 15:50:36 +0000 (17:50 +0200)]
ramips: Remove left-over mistyped device string from 02_network
In 2011 (!), network setup for nexaira,bc2 was moved to network
defaults script with a typo so it became b2c:
295e04084c ("ramips: setup bc2 mac addresses from the generic network script")
This patch just removes the useless entry without replacement,
since it seems to have worked for 8 years anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Chuanhong Guo [Fri, 21 Jun 2019 10:33:53 +0000 (18:33 +0800)]
ath79: add wmac migration for all ar93xx/qca95xx SoCs
Add migration for all ar71xx device path as well as previously
incorrect ath79 path.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Fri, 21 Jun 2019 10:25:12 +0000 (18:25 +0800)]
ath79: ar93xx/qca95xx: move gmac/wmac/pcie node out of apb bus
according to functional block diagram in datasheet, these devices
don't belong to apb bus.
Move these nodes out to match datasheet description.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Mon, 15 Jul 2019 11:43:31 +0000 (19:43 +0800)]
ath79: add support for Qihoo C301
Specifications:
- SoC: AR9344
- RAM: 128MB
- Flash: 2 * 16MB (MX25L12845)
- Ethernet: 2 * FE LAN & 1 * FE WAN
- WiFi: 2.4G: AR9344 5G: QCA9882
Flash instruction:
1. Hold reset and power up the router
2. Set your IP to 192.168.1.x
3. Open 192.168.1.1 and upload the generated *factory* firmware
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Sat, 13 Jul 2019 09:59:03 +0000 (17:59 +0800)]
ramips: mtk-mmc: mt76x8: check ESD_MODE before applying AGPIO_CFG
Since mt76x8an ver1 eco2, SDXC pins can be switched to the
following pinmap:
sd_d1 -> PAD_I2S_SDI
sd_d0 -> PAD_I2S_WS
sd_cmd -> PAD_I2S_CLK
sd_d3 -> PAD_I2C_SCLK
sd_d2 -> PAD_I2C_SD
sd_clk -> PAD_GPIO0
sd_wp -> PAD_TXD1
sd_cd -> PAD_RXD1
To use this pinmap, one would need to set ESD_MODE bit (bit 15)
to 1 in GPIO1_MODE and switch other used pads into GPIO mode.
In this mode, we don't need to switch ethernet pins to digital
pad.
Check ESD_MODE bit before applying AGPIO_CFG and use rt_sysc_m32
to set it.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Moritz Warning [Sun, 14 Jul 2019 08:53:27 +0000 (10:53 +0200)]
mpc85xx: split up DEVICE_TITLE
Splits up DEVICE_TITLE into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Rafał Miłecki [Sun, 14 Jul 2019 20:24:54 +0000 (22:24 +0200)]
libroxml: bump to the 3.0.2 version
* Fix for memory leak regression
* Support for (un)escaping
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Eneas U de Queiroz [Mon, 15 Jul 2019 17:08:00 +0000 (14:08 -0300)]
target/toolchain/files/wrapper.sh: simplify 'case'
Removed an eglibc remnant, and while at it, grouped all of the
TOOLCHAIN_PLATFORMs using the same FLAGS together.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Eneas U de Queiroz [Mon, 15 Jul 2019 17:07:59 +0000 (14:07 -0300)]
libs/toolchain: remove eglibc remnant file
This removes package/libs/toolchain/eglibc-files/etc/nsswitch.conf.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Moritz Warning [Sun, 14 Jul 2019 08:35:21 +0000 (10:35 +0200)]
tegra: split up DEVICE_TITLE
Splits up DEVICE_TITLE into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Rafał Miłecki [Wed, 3 Jul 2019 09:16:22 +0000 (11:16 +0200)]
ubox: implement service_running() in log init.d script
It allows checking if service is running.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Wed, 3 Jul 2019 09:16:21 +0000 (11:16 +0200)]
rpcd: implement service_running() in init.d script
It allows checking if service is running.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Petr Štetiar [Sun, 14 Jul 2019 20:10:37 +0000 (22:10 +0200)]
fstools: add direct dependencies on libblobmsg-json and libjson-c
The OpenWrt buildroot ABI version rebuild tracker does not handle
transient dependencies, therefore add all libraries linked by
block-mount and blockd as direct dependencies to the corresponding
binary package definition.
This ensures that block-mount and blockd is automatically rebuilt and
relinked if any of these libraries has its ABI_VERSION updated in the
future.
Fixes: FS#2373
[jow: similar fix for procd and 98.42% of commit message]
Signed-off-by: Jo-Philip Wich <jow@mein.io>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
David Bauer [Tue, 11 Jun 2019 15:27:51 +0000 (17:27 +0200)]
ath79: add support for devolo WiFi pro 1750x
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN: 1x Reset
LED: 1x LED Power (non-controllable)
1x LED Status (internal)
1x LED LAN (controlled by PHY)
1x LED WLAN
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to external-LED header.
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
Linus Walleij [Wed, 10 Jul 2019 17:46:12 +0000 (19:46 +0200)]
gemini: Stop enforcing command line
The command line enforced by the kernel is harmful, we want to
use the command line passed from the device tree. This is
especially important for the SQ201, Teltonika RUT and WBD111
which has a console set to 115200n8 and not 19200n8 like all
the others, so their consoles will be confusingly changing
baudrate between boot loader and kernel. The setting in the
device tree corresponds to what the boot loader is using.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
David Bauer [Tue, 2 Jul 2019 21:57:18 +0000 (23:57 +0200)]
gpio-button-hotplug: unify polled and interrupt code
This patch unifies the polled and interrupt-driven gpio_keys code
paths as well implements consistent handling of the debounce
interval set for the GPIO buttons and switches.
Hotplug events will only be fired if
1. The input changes its state and remains stable for the duration
of the debounce interval (default is 5 ms).
2. In the initial stable (no state-change for duration of the
debounce interval) state once the driver module gets loaded.
Switch type inputs will always report their stable state.
Unpressed buttons will not trigger an event for the initial
stable state. Whereas pressed buttons will trigger an event.
This is consistent with upstream's gpio-key driver that uses
the input subsystem (and dont use autorepeat).
Prior to this patch, this was handled inconsistently for interrupt-based
an polled gpio-keys. Hence this patch unifies the shared logic into the
gpio_keys_handle_button() function and modify both implementations to
handle the initial state properly.
The changes described in 2. ) . can have an impact on the
failsafe trigger. Up until now, the script checked for button
state changes. On the down side, this allowed to trigger the
failsafe by releasing a held button at the right time. On the
plus side, the button's polarity setting didn't matter.
Now, the failsafe will only engage when a button was pressed
at the right moment (same as before), but now it can
theoretically also trigger when the button was pressed the
whole time the kernel booted and well into the fast-blinking
preinit phase. However, the chances that this can happen are
really small. This is because the gpio-button module is usually
up and ready even before the preinit state is entered. So, the
initial pressed button event gets lost and most devices behave
as before.
Bisectors: If this patch causes a device to permanently go into
failsafe or experience weird behavior due to inputs, please
check the following:
- the GPIO polarity setting for the button
- the software-debounce value
Run-tested for 'gpio-keys' and 'gpio-keys-polled' on
- devolo WiFi pro 1200e
- devolo WiFi pro 1750c
- devolo WiFi pro 1750x
- Netgear WNDR4700
- Meraki MR24
- RT-AC58U
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [further
cleanups, simplification and unification]
Álvaro Fernández Rojas [Sat, 13 Jul 2019 11:33:44 +0000 (13:33 +0200)]
brcm2708: Add Raspberry Pi 4 support
- Support added to bcm2709 subtarget (32 bit).
- 64 bit kernel still requires many hacks on RPi 4B.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Sat, 13 Jul 2019 11:30:57 +0000 (13:30 +0200)]
brcm2708: switch to linux-firmware SDIO NVRAM
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Sat, 13 Jul 2019 11:34:59 +0000 (13:34 +0200)]
linux-firmware: add RPi SDIO NVRAM packages
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Tue, 9 Jul 2019 18:17:31 +0000 (20:17 +0200)]
brcm2708-gpu-fw: add support for Raspberry Pi 4
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Tue, 9 Jul 2019 18:32:28 +0000 (20:32 +0200)]
brcm2708: add linux 4.19 support
Boot tested on Raspberry Pi B+ (BCM2708) and Raspberry Pi 2 (BCM2709)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Felix Fietkau [Sat, 13 Jul 2019 14:00:43 +0000 (16:00 +0200)]
mt76: revert an accidental leftover debug change
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hans Dedecker [Sat, 13 Jul 2019 11:24:56 +0000 (13:24 +0200)]
procd: update to latest git HEAD
31f0765 procd: check strchr() result before using it
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Felix Fietkau [Fri, 12 Jul 2019 14:11:45 +0000 (16:11 +0200)]
mt76: update to the latest version
8fc3e6e mt76: mt7615: fix using VHT STBC rates
b21b991 mt76: mt7615: fix PS buffering of action frames
3d43dd8 mt76: mt7615: fix invalid fallback rates
0ce4682 mt76: mt7603: fix invalid fallback rates
3b08966 Revert "mt76: usb: use full intermediate buffer in mt76u_copy"
48800e7 Revert "mt76: usb: remove unneeded {put,get}_unaligned"
439354d Revert "mt76: usb: fix endian in mt76u_copy"
8c1da93 mt76: usb: fix endian in mt76u_copy
307be50 mt76: usb: remove unneeded {put,get}_unaligned
5d29829 mt76: mt76x02: use params->ssn value directly
f74d117 mt76: mt7603: use params->ssn value directly
649f2e8 mt76: mt7615: use params->ssn value directly
b647180 mt76: mt7615: unlock dfs bands
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hauke Mehrtens [Thu, 11 Jul 2019 23:12:11 +0000 (01:12 +0200)]
mac80211: Do not build b43legacy on BRCM47xx mips74 subtarget
b43legacy needs ssb support and we do not compile the mips74 subtarget
of the brcm47xx target with SSB support. This causes a build failure in
the mac80211 package and only some of the kernel modules are being
created.
I am not aware of any device with a BRCM47xx mips74 CPU which uses a
b43legacy compatible device.
Fixes: FS#2334
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
David Bauer [Thu, 11 Jul 2019 15:15:48 +0000 (17:15 +0200)]
ramips: add support for ASUS RT-AC57U
SoC: MediaTek MT7621AT
RAM: 128M (Winbond W631GG6KB-15)
FLASH: 16MB (Spansion S25FL128SA)
WiFi: MediaTek MT7603EN bgn 2SS
WiFi: MediaTek MT7612EN nac 2SS
BTN: Reset - WPS
LED: - Power
- LAN {1-4}
- WAN
- WiFi 2.4 GHz
- WiFi 5 GHz
- USB
UART: UART is present next to the Power LED.
TX - RX - GND - 3V3 / 57600-8N1
3V3 is the nearest one to the Power LED.
Installation
------------
Via TFTP:
1. Set your computers IP-Address to 192.168.1.75.
2. Power up the Router with the Reset button pressed.
3. Release the Reset button after 5 seconds.
4. Upload OpenWRT sysupgrade image via TFTP:
> tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE>
Via SSH:
Note: User/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt sysupgrade image via scp:
> scp owrt.bin admin@192.168.1.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.1.1
5. Write the OpenWrt image to flash.
> mtd-write -i /tmp/owrt.bin -d linux
6. Reboot the router
> reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
Colby Whitney [Tue, 2 Jul 2019 17:18:00 +0000 (11:18 -0600)]
lua5.3: build shared library
Update the lua5.3 package to build a shared object just like the old lua
package. Ported / recreated the same patch number as the other lua
package. Built and tested library / interpreter on BCM5301X.
Signed-off-by: Colby Whitney <colby.whitney@luxul.com>
Chuanhong Guo [Thu, 11 Jul 2019 15:21:19 +0000 (23:21 +0800)]
ramips: fix mqmaker witi case in fixup-mac-address
This commit fixes a forgotten case in previous commit.
Fixes: 087e14ab59 ("ramips: mt7621: merge two variants of MQmaker WiTi together")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Rafał Miłecki [Wed, 3 Jul 2019 07:51:49 +0000 (09:51 +0200)]
base-files: move stage2 upgrade to separated file
do_upgrade_stage2() isn't really any common code. It isn't used anywhere
except for /sbin/sysupgrade that passes it to the stage2.
Moving its code to separated file also simplifies COMMAND variable.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Chuanhong Guo [Wed, 10 Jul 2019 15:57:36 +0000 (23:57 +0800)]
ramips: mt7621: merge two variants of MQmaker WiTi together
Since we can auto-detect memory now, we don't need 2 dts for two
memory variants.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Wed, 10 Jul 2019 05:53:59 +0000 (13:53 +0800)]
ramips: dts: drop memory nodes
mt7621 and mt7628 now have the ability to detect memory size
automatically.
Drop memory nodes and let kernel determine memory size.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Wed, 10 Jul 2019 03:05:41 +0000 (11:05 +0800)]
ramips: mt7621: add support for memory detection
mt7621 has the following memory map:
0x0-0x1c000000: lower 448m memory
0x1c000000-0x2000000: peripheral registers
0x20000000-0x2400000: higher 64m memory
detect_memory_region in arch/mips/kernel/setup.c only add the first
memory region and isn't suitable for 512m memory detection because
it may accidentally read the memory area for peripheral registers.
This commit adds memory detection capability for mt7621:
1. add the highmem area when 512m is detected.
2. guard memcmp from accessing peripheral registers:
This only happens when some weird user decided to change
kernel load address to 256m or higher address. Since this
is a quite unusual case, we just skip 512m testing and return
256m as memory size.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Daniel Golle [Wed, 10 Jul 2019 17:28:35 +0000 (19:28 +0200)]
ramips: fix bogus MTK_SOC (typo)
Belkin F7C027 is clearly Rt5350 SoC, as shown on internal
photographs filed for FCC approval[1].
[1]: https://fcc.io/K7S/F7C027
Fixes commit
3b0264eddbc
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adrian Schmutzler [Sun, 7 Jul 2019 14:27:51 +0000 (16:27 +0200)]
ramips: Sort all subtarget Makefiles
This patch applies sorting to the definitions as whole blocks.
Sorting has been performed fully automatic, line count differences
originate from double empty lines removed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 3 Jul 2019 21:22:47 +0000 (23:22 +0200)]
ramips: Reapply sorting to board.d files
This patch is cosmetical:
It only applies sorting based on device names, whereas renames
already took place in earlier patches.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 3 Jul 2019 21:22:44 +0000 (23:22 +0200)]
kernel/om-watchdog: Apply device renames from ramips
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 3 Jul 2019 21:22:42 +0000 (23:22 +0200)]
uboot-envtools: Apply ramips device renames
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 3 Jul 2019 21:22:39 +0000 (23:22 +0200)]
ramips: Remove base-files/lib/ramips.sh
Having converted the target to use device compatible, ramips.sh
is obsolete now.
The only remaining entry for the mt7688 evaluation board seems to
be orphaned.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 3 Jul 2019 21:22:36 +0000 (23:22 +0200)]
ramips/rt305x: Name DTS files based on scheme
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 3 Jul 2019 21:22:34 +0000 (23:22 +0200)]
ramips/rt288x,rt3883: Name DTS files based on scheme
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 3 Jul 2019 21:22:31 +0000 (23:22 +0200)]
ramips/mt76x8: Name DTS files based on scheme
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 3 Jul 2019 21:22:28 +0000 (23:22 +0200)]
ramips/mt7621: Name DTS files based on scheme
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 3 Jul 2019 21:22:25 +0000 (23:22 +0200)]
ramips/mt7620: Name DTS files based on scheme
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 3 Jul 2019 21:22:22 +0000 (23:22 +0200)]
ramips: Derive DTS name from device name in Makefile
This will automatically derive the DTS name as in ath79 and thus
makes specifying DTS for every device obsolete.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
---
This patch only introduces the mechanism and is then followed by
commits with renames and Makefile adjustments per subtarget.
Eventually, those can be all squashed into a single commit or left
as they are to enhance overview.
Adrian Schmutzler [Wed, 3 Jul 2019 21:22:19 +0000 (23:22 +0200)]
ramips/rt305x: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 3 Jul 2019 21:22:16 +0000 (23:22 +0200)]
ramips/rt288x,rt3883: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 3 Jul 2019 21:22:13 +0000 (23:22 +0200)]
ramips/mt76x8: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 3 Jul 2019 21:22:08 +0000 (23:22 +0200)]
ramips/mt7621: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 3 Jul 2019 21:22:02 +0000 (23:22 +0200)]
ramips/mt7620: Synchronize Makefiles with DTS compatible
This will "rename" devices in Makefiles to the pattern used in
DTS compatible. This will systematize naming of devices
enormously.
As device names are used to for default SUPPORTED_DEVICES entries,
we need to adjust the source for /tmp/sysinfo/board_name, too.
So remove relevant entries from base-files/lib/ramips.sh and
use device compatible for that.
Despite that, base-files are updated, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 3 Jul 2019 21:21:54 +0000 (23:21 +0200)]
ramips: Improve compatible for TP-Link Archer devices
Include "Archer" in compatible as it is part of the device name.
Update Makefile device names where necessary to match compatible.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Chen Minqiang [Sun, 7 Jul 2019 08:02:49 +0000 (16:02 +0800)]
ath79: fix missing DEVICE_VENDOR for some devices
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Daniel Golle [Wed, 10 Jul 2019 15:15:49 +0000 (17:15 +0200)]
ramips: add missing DEVICE_VENDOR
Fixes commit
ee66fe4ea9a6f5e3f47a063f850bac57e1fb411a
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Luis Araneda [Sat, 6 Jul 2019 02:26:00 +0000 (22:26 -0400)]
sunxi: convert to multi-variable device title
Use data from the linux-sunxi community wiki to
fill-in missing device information
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Luis Araneda [Sat, 6 Jul 2019 04:50:32 +0000 (00:50 -0400)]
ipq40xx: convert to multi-variable device title
Additionally, fix some vendor and board names
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Moritz Warning [Sun, 7 Jul 2019 13:17:31 +0000 (15:17 +0200)]
kirkwood: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Moritz Warning [Sun, 7 Jul 2019 13:17:11 +0000 (15:17 +0200)]
ath25: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Daniel Golle [Sat, 6 Jul 2019 19:21:34 +0000 (21:21 +0200)]
oxnas: convert DEVICE_TITLE to new variables
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fredrik Olofsson [Thu, 4 Jul 2019 11:58:15 +0000 (13:58 +0200)]
kernel: cherry pick patch removing __linux__ check
This is already included in newer upstream. Needed to build BPF programs
using the MIPS kernel include files.
Without this patch, clang fails with "#error Use a Linux compiler or
give up." in sgidefs.h when building BPF programs.
Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
John Crispin [Wed, 10 Jul 2019 11:32:24 +0000 (13:32 +0200)]
include/package.mk: Add support for src-checkout/ folder
This feature is similar to the SRC_TREE_OVERRIDE. However instead of having
to manually create a symlink inside the package folder, the buildsystem
will check if $(TOP_DIR)/src-checkout/$(PKG_NAME)/.git is present and use
this instead.
Signed-off-by: John Crispin <john@phrozen.org>
Adrian Schmutzler [Tue, 9 Jul 2019 11:05:46 +0000 (13:05 +0200)]
ath79: Fix whitespace errors in 11-ath10k-caldata
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 8 Jul 2019 08:17:28 +0000 (10:17 +0200)]
base-files: Fix path check in get_mac_binary
Logic was inverted when changing from string check to file check.
Fix it.
Fixes: 8592602d0a88 ("base-files: Really check path in get_mac_binary")
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 8 Jul 2019 21:14:03 +0000 (23:14 +0200)]
rb532: Fix missing DEVICE_TITLE
This fixes the collection of target info during build, where the
device title for rb532/nand is just empty:
tmp/.config-target.in:44925:warning: leading whitespace ignored
tmp/.config-target.in:123738:warning: leading whitespace ignored
tmp/.config-target.in:123786:warning: leading whitespace ignored
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Koen Vandeputte [Tue, 9 Jul 2019 10:43:23 +0000 (12:43 +0200)]
kernel: bump 4.19 to 4.19.57
Refreshed all patches.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Tue, 9 Jul 2019 10:18:49 +0000 (12:18 +0200)]
kernel: bump 4.14 to 4.14.132
Refreshed all patches.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Kevin Darbyshire-Bryant [Tue, 9 Jul 2019 12:40:32 +0000 (13:40 +0100)]
netsupport: move out sch_cake from kmod-sched
Fix file installation clash between kmod-sched & kmod-sched-cake as both
try to install sch_cake.ko
Remove cake from kmod-sched package as cake is supposed to be the
optional qdisc.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Lucian Cristian [Sun, 30 Jun 2019 06:31:15 +0000 (09:31 +0300)]
kernel: x86: enable NVME support for 64 bit target
Newer motherboards support NVMe U.2 connectors but also NVMe storage can
be used on add-on pcie adapters.
Enable kernel driver on x86 for now so the NVMe flash storage can be used
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Chuanhong Guo [Thu, 27 Jun 2019 12:44:27 +0000 (20:44 +0800)]
ramips: use upstream RAW_APPENDED_DTB instead of our OWRTDTB
Upstream kernel added support for RAW_APPENDED_DTB on ralink arch
in the following commit:
02564fc89d3d ("ralink: Introduce fw_passed_dtb to arch/mips/ralink")
Use upstream solution and get rid of our OWRTDTB hack.
This commit set DEVICE_DTS to $$(DTS) instead of replacing DTS with
DEVICE_DTS in device profile because DTS variable will be dropped
in later commits.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on mt7621/mt76x8]
Tested-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on rt305x/mt7620]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Rosen Penev [Sun, 7 Jul 2019 21:30:17 +0000 (14:30 -0700)]
usbreset: Add missing header
Fixes undefined reference to strtoul
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Konstantin Demin [Fri, 28 Jun 2019 18:30:50 +0000 (21:30 +0300)]
netsupport: move out mqprio from kmod-sched
Currently, there's unable to install "kmod-sched-mqprio" after
"kmod-sched" (or vice versa), because "sch_mqprio.ko" is
shipped in both packages.
Fixes: f83522fa6361 ("linux: Add kmod-sched-mqprio")
Fixes: 6af639e0bf78 ("linux: Add kmod-sched-act-vlan")
Fixes: 72c7e2dc467c ("linux: Add kmod-sched-flower")
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
[Add cls_flower and act_vlan]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Daniel Engberg [Sat, 15 Jun 2019 10:20:44 +0000 (10:20 +0000)]
util-linux: Update to 2.34
Update util-linux to 2.34
Refresh patch
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
projects / openwrt / staging / jow.git / log