drm/amd/display: dont set  otg offset

move the update of otg instance outside of hw programming logic,
since this is sw state, it should always be updated and should
never be optimized away.

Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Explicitly specify update type per plane info change

[Why]
The bit for flip addr is being set causing the determination for
FAST vs MEDIUM to always return MEDIUM when plane info is provided
as a surface update. This causes extreme stuttering for the typical
atomic update path on Linux.

[How]
Don't use update_flags->raw for determining FAST vs MEDIUM. It's too
fragile to changes like this.

Explicitly specify the update type per update flag instead. It's not
as clever as checking the bits itself but at least it's correct.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Eryk Brol <Eryk.Brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Rename EDID_BLOCK_SIZE to DC_EDID_BLOCK_SIZE

Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Use VCP for extended colorimetry

DPRX should send the VCP extended colorimetry packet if the
sink supports DPCD rev1.4 and reports the extended colorimetry
bit.

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Use DCN functions instead of DCE

[WHY]
DCN code should make as few references to DCE as possible

[HOW]
Copy DCE110 implementation of find_first_free_match_stream_enc_for_link
into DCN10

Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Engine-specific encoder allocation

[WHY]
From DCE110 onward, we have the ability to assign DIG BE and FE
separately for any display connector type; before, we could only do this
for DP.

Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: enabling stream after HPD low to high happened

[Why]
1. No real HPD plug in/out but HPD happens,
 the driver notifies OS connection changed.
2. No display in target.

When HPD goes low to high,
the driver should regard as HPD and enter setmode flow.

[How]
In this case, even stream didn't change but still retrain.

Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Program VTG params after programming Global Sync

[Why]
VTG has a parameter FP2, which is defined as:
    if VSTARTUP is before VSYNC:
        FP2 = number of lines in between VSTARTUP and VSYNC
    else
        FP2 = 0
Currently, FP2 is only programmed during "program_timing". However, the
position of VSTARTUP is affected by the prefetching requirements on all pipes,
so the position might change when we do memory request control on another pipe, so we need
to make sure that FP2 stays up-to-date whenever we adjust VSTARTUP.

[How]
 - refactor VTG_CONTROL programming into a new function "set_vtg_params"
 - call it after calling "program_global_sync"
   - make sure it's called after because it relies on the cached dlg params

Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add null checks and set update flags

* add plane state null checks
* add and set update surface flags

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: 3.2.30

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Reuse MPC OGRAM for 1D blender

[Why & How]
Reuse existent code path and in order to do that apply de gamma
in 1D blender LUT and re use MPC OGAM.
Follow up is required.

Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Remove DPMS state dependency for fast boot

[Why]
The DPMS state of a display should not impact whether we want to enable fast boot.
Currently fast boot is not enabled when resuming from S4 because of this.

[How]
Remove check for DPMS state when determining if fast boot
can be applied.

Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Hook up CRC capture support for dce120

[Why]
Many IGT tests require CRC capture in order to confirm that the output
is visually correct.

These skip on dce120 because configure_crc and get_crc aren't set.

[How]
Hook up is_tg_enabled, configure_crc and get_crc functions on dce120's
timing generator.

The logic should be the same as DCE and DCN with some minor register
naming differences.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: define v_total_min and max parameters

add these parameters for future use

Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: support sw smu hotspot and memory temperature retrieval

Support hotspot and memory temperature retrieval on sw smu routine.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: support uclk activity retrieve on sw smu routine

Support realtime uclk activity report.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: honor hw limit on fetching metrics data

Request too frequently may get corrupt data.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: support ppfeatures sysfs interface on sw smu routine

Support ppfeatures sysfs interface on Vega20 sw smu routine.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: drop redundant smu call

smu_get_clk_info_from_vbios() was called repeatedly. It
seems a merge error.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: drop unnecessary sw smu check

There is already sw smu check on IP block adding.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Drop DCN1_01 guards

[WHY]
These were only needed for bringup. They're not needed anymore.

Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Don't load DMCU for Raven 1 (v2)

[WHY]
Some early Raven boards had a bad SBIOS that doesn't play nicely with
the DMCU FW. We thought the issues were fixed by ignoring errors on DMCU
load but that doesn't seem to be the case. We've still seen reports of
users unable to boot their systems at all.

[HOW]
Disable DMCU load on Raven 1. Only load it for Raven 2 and Picasso.

v2: Fix ifdef (Alex)

Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add ASICREV_IS_PICASSO

[WHY]
We only want to load DMCU FW on Picasso and Raven 2, not on Raven 1.

Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/amdgpu: Report firmware versions with sysfs v2

Firmware versions can be found as separate sysfs files at:
/sys/class/drm/cardX/device/fw_version (where X is the card number)
The firmware versions are displayed in hexadecimal.
v2: Moved sysfs files to subfolder

Signed-off-by: Ori Messinger <ori.messinger@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: make VCN DPG pause mode detached from general VCN

It should be attached to VCN 1.0

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: move the VCN DPG mode read and write to VCN

Since this is VCN specific and only used by VCN

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/sriov: Need to initialize the HDP_NONSURFACE_BAStE

it requires to initialize HDP_NONSURFACE_BASE, so as to avoid
using the value left by a previous VM under sriov scenario.

v2: it should not hurt baremetal, generalize it for both sriov
and baremetal

Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Tiecheng Zhou <Tiecheng.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: suppress repeating tmo report

only report once per TMO job and the timer would
be restarted upon the job finished if it's just slow.

Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: remove static GDS, GWS and OA allocation

As far as we know this was never used by userspace and so should be removed.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: update Vega10 ACG Avfs Gb parameters

Update Vega10 ACG Avfs GB parameters.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: force to update all clock tables on OD reset

On OD reset, the clock tables in SMU need to be reset to default.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: update Vega10 power state on OD

Update Vega10 top performance level power state accordingly
on OD.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: avoid repeat AVFS enablement/disablement

No need to enable or disable AVFS if it's already in wanted
state.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: valid Vega10 DPMTABLE_OD_UPDATE_VDDC settings V2

With user specified voltage(DPMTABLE_OD_UPDATE_VDDC), the AVFS
will be disabled. However, the buggy code makes this actually not
working as expected.

- V2: clear all OD flags excpet DPMTABLE_OD_UPDATE_VDDC

Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: fix Vega10 mclk/socclk voltage link setup

This may affects the Vega10 MCLK OD functionality.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: check no_user_fence flag for engines

To replace checking ring type and make them generic

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/VCN: set no_user_fence flag to true

There is no user fence support for VCN

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/VCE: set no_user_fence flag to true

There is no user fence support for VCE

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/UVD: set no_user_fence flag to true

There is no user fence support for UVD

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add no_user_fence flag to ring funcs

So we can generalize the no user fence supported engine

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: sdma handle ras resume

During S3/S4 bootloader will re-init ras state behind us.
Resume might fail or raise a gpu reset.

Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: gfx handle ras resume

During S3/S4 bootloader will re-init ras state behind us.
Resume might fail or raise a gpu reset.

Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: gmc handle ras resume

During S3/S4 bootloader will re-init ras state behind us.
Resume might fail or raise a gpu reset.

Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: enable ras suspend/resume

suspend/resume will change ras state behind us. Let driver get notified.

Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: ras support suspend/resume

add ras suspend function. rename ras_post_init to amdgpu_ras_resume.

Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add badpages sysfs interafce

add badpages node.
it will output badpages list in format
gpu pfn : gpu page size : flags

example
0x00000000 : 0x00001000 : R
0x00000001 : 0x00001000 : R
0x00000002 : 0x00001000 : R
0x00000003 : 0x00001000 : R
0x00000004 : 0x00001000 : R
0x00000005 : 0x00001000 : R
0x00000006 : 0x00001000 : R
0x00000007 : 0x00001000 : P
0x00000008 : 0x00001000 : P
0x00000009 : 0x00001000 : P

flags can be one of below characters
R: reserved.
P: pending for reserve.
F: failed to reserve for some reasons.

Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Fix S3 test issue

During S3 test, when system wake up and resume, ras interface
is already allocated. Move workaround before ras jumps to resume
step in gfx_v9_0_ecc_late_init, and make sure workaround applied
during resume. Also remove unused mmGB_EDC_MODE clearing.

Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Make some functions static

Fix the following sparse warnings:

drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:483:21: warning: symbol 'dce120_clock_source_create' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:506:6: warning: symbol 'dce120_clock_source_destroy' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:513:6: warning: symbol 'dce120_hw_sequencer_create' was not declared. Should it be static?

Fixes: b8fdfcc6a92c ("drm/amd/display: Add DCE12 core support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai26@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: RLC to program regs for Vega10 SR-IOV

Under Vega10 SR-IOV, with new RLC's new feature, VF should call RLC
to program some registers if supported

Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add basic func for RLC program reg

New feature for RLC, some registers can be programmed by
RLC interface under SR-IOV VF:

WREG32_SOC15_RLC_SHADOW:
1, for GRBM_GFX_CNTL, firstly the new register value should be be
programmed to SCRATCH_REG2
1, for GRBM_GFX_INDEX, firstly the new register value should be be
programmed to SCRATCH_REG3

WREG32_RLC:
for registers supported to be programmed by RLC interface, the
following sequence should be used:
1, write the value to SCRATCH_REG0
2, write reg | 0x80000000 to SCRATCH_REG1
3, write 0x1 to RLC_SPARE_INT to notify RLC
4, polling SCRATCH_REG1 to check if finished

Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Skip setting some regs under Vega10 VF

For Vega10 SR-IOV VF, skip setting some regs due to:
1, host will program them
2, avoid VF register programming violations

Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Support PSP VMR ring for Vega10 VF

Add VMR ring support for Vega10 SR-IOV VF if PSP supported

Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: call psp to program ih cntl in SR-IOV

call psp to program ih cntl in SR-IOV if supported

Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: implement PSP cmd GFX_CMD_ID_PROG_REG

Add implementation to program regs by PSP, currently the following
IH registers are supported:
IH_RB_CNTL
IH_RB_CNTL_RING1
IH_RB_CNTL_RING2

Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Add new PSP cmd GFX_CMD_ID_PROG_REG

Add new PSP command GFX_CMD_ID_PROG_REG definition

Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: initialize PSP before IH under SR-IOV

In order to support new PSP feature that PSP may provide interface
to program IH CNTL register, initialize PSP before IH under Vega10
SR-IOV VF

Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: init vega10 SR-IOV reg access mode

Set different register access mode according to the features
provided by firmware

Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: gpu reset will run ras post init

ras need initialize proper state after late init

Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: sdma support ras gpu reset

request a gpu reset if ras return EAGAIN.
we will run late init again so it is ok to do nothing this time.

Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: gfx support ras gpu reset

request a gpu reset if ras return EAGAIN.
we will run late init again so it is ok to do nothing this time.

Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: gmc support ras gpu reset

request a gpu reset if ras return EAGAIN.
we will run late init again so it is ok to do nothing this time.

Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: handle ras reset

add another flag to allow IP do a gpu reset after device init.

Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Issue ras TA disable/enable cmd forcely on boot

Check ras TA error code and return EAGAIN.
Issue ras enable/disable cmd without checking currect state.
Looks like ras TA will handle current state == target state case.

Now driver might need do a reset to satisfy ras TA.

Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Revert "drm/amdgpu: skip gpu reset when ras error occured"

Enable this now to reset the GPU on RAS errors.

This reverts commit 138352e5752aa3e694951d70c8fe8730219f4edf.

Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: gpu reset will run late_init

ras need late init to initialize proper state.

Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add df perfmon regs and funcs for xgmi

v6: Squash in warning fix (Colin Ian King)
v5: Fix warnings (Alex)
v4: fixed mixed delaration and code warnings and minor errors
v3: exposing df funcs in amdgpu_df_funcs in amdgpu.h
v2: moving permonctl/perfmonctr from default to offset

- adding df perfmonctl and perfmonctr registers for df counters
- adding df funcs to set perfmonctl and get perfmonctr for
df and xgmi counters
- exposing df funcs in amdgpu_df_funcs

Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add gfx9 gpr EDC workaround when RAS is enabled

When RAS is enabled, initializes the VGPRs/LDS/SGPRs and
resets EDC error counts. This is done in late_init, before
RAS TA GFX enable.

Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add EDC counter register

Add EDC counter register to support gfx9 gpr EDC workaround to
clear all EDC counters.

Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Reserve shared fence for eviction fence

Need to reserve space for the shared eviction fence when initializing
a KFD VM.

Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Expose send immediate sdp message interface

[Why]
To send sdp message immediately from a single slot.

[How]
Modify the generic SDP message interface, and use GSP4 to send immediate
sdp message.

Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fill plane attrs only for valid pxl format

[Why]
In fill_plane_buffer_attributes() we calculate chroma/luma
assuming that the surface_pixel_format is always valid.
If it's not the case, there's a risk of divide by zero error.

[How]
Check if format valid before calculating pixel format attributes

Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: move back vbios cmd table for set dprefclk

[Why]
Upon closer inspection, our previous implementation is missing
code for programming de-spread and DP DTO. Porting this logic
into driver is rather involved, as there are a lot of table
look ups. So for now move back to calling vbios cmd table

[How]
Go back to calling vbios cmd table for set dp_refclk

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix acquire_first_split_pipe function

This function needs to re-calculate the scaling on the pipe
that loses it's half.

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: stop external access to internal optc sync params

These are internal otg params and should be handled as such.
Thich change passes the params as function arguments.

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: move signal type out of otg dlg params

It makes no logical sense being there

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: reset retimer/redriver below 340Mhz

[Description]
This is for HDMI 6Ghz mode before we load the driver, because VBIOS
not support HDMI (6Ghz mode)

Reset to redriver/retimer setting for the setting for below 340Mhz.

Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: color space ycbcr709 support

Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Duke Du <Duke.Du@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Define Byte 14 on AVI InfoFrame

[Why]
Part of HDMI 2.1 requires AVI InfoFrame version update
from current V2 to V4 for new colorimetry.

[How]
Define V4 AVI InfoFrame ACE0-ACE3 bit.

Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: 3.2.29

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Disable cursor when offscreen in negative direction

[Why]
When x or y is negative we set the x and y values to 0 and compensate
with a positive cursor hotspot in DM since DC expects positive cursor
values.

When x or y is less than or equal to the maximum cursor width or height
the cursor hotspot is clamped so the hotspot doesn't exceed the
cursor size:

if (x < 0) {
        xorigin = min(-x, amdgpu_crtc->max_cursor_width - 1);
        x = 0;
}

if (y < 0) {
        yorigin = min(-y, amdgpu_crtc->max_cursor_height - 1);
        y = 0;
}

This incorrectly forces the cursor to be at least 1 pixel on the screen
in either direction when x or y is sufficiently negative.

[How]
Just disable the cursor when it goes far enough off the screen in one
of these directions.

This fixes kms_cursor_crc@cursor-256x256-offscreen.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fill prescale_params->scale for RGB565

[Why]
An assertion is thrown when using SURFACE_PIXEL_FORMAT_GRPH_RGB565
formats on DCE since the prescale_params->scale wasn't being filled.

Found by a dmesg-fail when running the
igt@kms_plane@pixel-format-pipe-a-planes test on Baffin.

[How]
Fill in the scale parameter.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Support AVI InfoFrame V3 and V4

[Why]
Part of HDMI 2.1 requires AVI InfoFrame version update
from current V2 to V3 for new VICs, and V4 for
new colorimetry.

[How]
Implement V3 and V4 AVI InfoFrame.
If (C1, C0)=(1, 1) and (EC2, EC1, EC0)=(1, 1, 1),
the Source shall use 20 AVI InfoFrame Version 4.
If VIC >= 128, the Source shall use AVI InfoFrame Version 3

Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: block passive dongle EDID Emulation for USB-C ports

[Why]
Emulating passive dongle on USB-C port causes issue on some asics.

[How]
Check for DP_IS_USB_C flag in bios parser and propagate it to
encoder features flags. If DP_IS_USB_C flag is set and it is trying to
emulate passive dongle, then return fail.

Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add SW_USE_I2C_REG request.

[Description]
This is for DC_I2c arbitration use between HW use/SW use and DMCU use.

Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add support for disconnected eDP panels

[why]
On some configurations, eDP from GPU is muxed with another GPU.  DC does
not know state of mux, but DM has this knowledge.  This flag allows DC to ignore
creating EDP link when DM informs DC that EDP mux is not connected.

[how]
Add flag to dc, populate flag in DM

Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Set dispclk and dprefclock directly

[Why]
To simply logic for setting DCN specific clocks, we will send
SMU message directly through the VBIOS message box.

[How]
Add new structure in pp_smu to hold functions to set clocks
through vbios message box

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix multi display seamless boot case

[Why]
There is a scenario that causes eDP to become blank if
there are multiple displays connected, and the external
display is set as the primary display such that the first
flip comes to the external display.

In this scenario, we call our optimize function before
the eDP even has a chance to flip.

[How]
There is a check that prevents bandwidth optimize from
occurring before first flip is complete on the seamless boot
display.
But actually it assumed the seamless boot display is the
first one to flip. But in this scenario it is not.
Modify the check to ensure the steam with the seamless
boot flag set is the one that has completed the first flip.

Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Refactor program watermark.

Refactor programming watermark function:
Divided into urgent watermark, stutter watermark and pstate watermark.

Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: 3.2.28

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: rename amdgpu_prime.[ch] into amdgpu_dma_buf.[ch]

We are getting a dma-buf implementation completely separate from drm prime,
so rename the files now and cleanup the code a bit.

No functional change.

Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/amdgpu: Add MEM_LOAD to amdgpu_pm_info debugfs file

Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Cosmetic cleanup

Fix some spacing issues, log output, uses of !=NULL/==NULL, unneeded
extra lines and clean up a declaration from =1 to =true for clarity

Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Fix CIK references in gmc_v8

gmc_v8 is for VI, not CIK, so fix those references

Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Add PCIe replay count sysfs file

Add a sysfs file for reporting the number of PCIe replays (NAKs). This
returns the sum of NAKs received and NAKs generated

Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Add replay counter defines to NBIO headers

Add the PCIE_RX_NUM_NACK and PCIE_RX_NUM_NACK_GENERATED values to the
NBIO SMN headers in preparation for exposing the number of PCIe replays
via sysfs

Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Update latest xgmi topology info after each device is enumulated

Adjust the sequence of set/get xgmi topology, so driver can have the latest
XGMI topology info for future usage

Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: enable separate timeout setting for every ring type V4

Every ring type can have its own timeout setting.

 - V2: update lockup_timeout parameter format and cosmetic fixes
 - V3: invalidate 0 and negative values
 - V4: update lockup_timeout parameter format

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add new sysfs interface for memory realtime utilization

A new sysfs interface mem_busy_percent is added for telling
how busy the VRAM is(in percentage).

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: expose SMU7 asics realtime memory utilization

Enable realtime memory utilization report on SMU7 asics.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: expose Vega12 realtime memory utilization

Enable realtime memory utilization report on Vega12.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>