drm/i915/execlists: Assert there are no simple cycles in the dependencies

The dependency chain must be an acyclic graph. This is checked by the
swfence, but for sanity, also do a simple check that we do not corrupt
our list iteration in execlists_schedule() by a shallow dependency
cycle.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-10-chris@chris-wilson.co.uk

drm/i915: Assert all signalers we depended on did indeed signal

Back up our comment that all signalers should have been signaled before
we ourselves were retired with an assert to that effect.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-9-chris@chris-wilson.co.uk

drm/i915: Hold rpm wakeref for modifying the global seqno

To modify the global seqno may require rewriting a few registers, which
requires us to hold the rpm wakeref. We must therefore take it around
the call to i915_gem_set_global_seqno() in debugfs, on behalf of the
user.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-15-chris@chris-wilson.co.uk

drm/i915/execlists: Tidy enabling execlists

Move the register settings for enabling execlists into its own function
for clarity.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-18-chris@chris-wilson.co.uk

drm/i915/execlists: Record elsp offset during engine setup

Currently, we record the elsp register offset inside init-hw but we only
need to do it once during engine setup (after we know the mmio
iomapping).

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-17-chris@chris-wilson.co.uk

drm/i915/execlists: Clear context-switch interrupt earlier in the reset

Move the clearing of the CS-interrupt into the engine reset phase,
before the current init-hw phase. This helps clarify that we clear the
pending interrupts prior to any restarting of the execlists.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-16-chris@chris-wilson.co.uk

drm/i915: Delete defunct i915_gem_request_assign()

i915_gem_request_assign() is not used since commit 77f0d0e925e8
("drm/i915/execlists: Pack the count into the low bits of the
port.request"), so remove the defunct code

References: 77f0d0e925e8 ("drm/i915/execlists: Pack the count into the low bits of the port.request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-1-chris@chris-wilson.co.uk

drm/i915/selftests: Allow random array allocation to fail

In the selftests, we don't want to force an oom and would rather
ENOMEM be reported. In this case, we would rather the allocation for the
random array to fail.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171223110407.21402-2-chris@chris-wilson.co.uk

drm/i915/selftests: Tweak igt_ggtt_page to speed it up

Reduce the number of GGTT PTE operations to speed the test up, but we
reduce the likelihood of spotting a coherency error in those operations.
However, Broxton is sporadically timing on this test, presumably because
its GGTT operations are all uncached.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171223110407.21402-1-chris@chris-wilson.co.uk

i915/drrs/debugfs: psr status info addition

Existing debugfs entry i915_drrs_status is updated with whether PSR
is the cause for DRRS disabled state.

[v2]: Dropped the module parameter details as ctl moved from module
      parameter to debugfs. [Rodrigo]

[v3]: Crtc ID information is dropped as there is no immediate usecase.
      [Rodrigo].

Signed-off-by: C, Ramalingam <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511151827-6596-1-git-send-email-ramalingam.c@intel.com

drm/i915: Runtime disable for eDP DRRS

Debugfs called i915_drrs_ctl is added to enable and disable the
eDP DRRS. Writing 0 will disable the feature, whereas non-zero
will enable the feature.

Possibility of disabling the DRRS, enables the testing of the
frontbuffer tracking based features (FBC, DRRS and PSR) as
standalone or any combination of the set.

[v2]: ctl interface is moved from module parameter to debugfs [Rodrigo]

Signed-off-by: C, Ramalingam <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1510079903-29441-1-git-send-email-ramalingam.c@intel.com

drm/i915/vlv: Add cdclk workaround for DSI

At least on the Chuwi Vi8 (non pro/plus) the LCD panel will show an image
shifted aprox. 20% to the left (with wraparound) and sometimes also wrong
colors, showing that the panel controller is starting with sampling the
datastream somewhere mid-line. This happens after the first blanking and
re-init of the panel.

After looking at drm.debug output I noticed that initially we inherit the
cdclk of 333333 KHz set by the GOP, but after the re-init we picked 266667
KHz, which turns out to be the cause of this problem, a quick hack to hard
code the cdclk to 333333 KHz makes the problem go away.

I've tested this on various Bay Trail devices, to make sure this not does
cause regressions on other devices and the higher cdclk does not cause
any problems on the following devices:
-GP-electronic T701      1024x600   333333 KHz cdclk after this patch
-PEAQ C1010              1920x1200  333333 KHz cdclk after this patch
-PoV mobii-wintab-800w    800x1280  333333 KHz cdclk after this patch
-Asus Transformer-T100TA 1368x768   320000 KHz cdclk after this patch

Also interesting wrt this is the comment in vlv_calc_cdclk about the
existing workaround to avoid 200 Mhz as clock because that causes issues
in some cases.

This commit extends the "do not use 200 Mhz" workaround with an extra
check to require atleast 320000 KHz (avoiding 266667 KHz) when a DSI
panel is active.

Changes in v2:
-Change the commit message and the code comment to not treat the GOP as
 a reference, the GOP should not be treated as a reference

Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171220105017.11259-1-hdegoede@redhat.com

drm/i915: Apply Display WA #1183 on skl, kbl, and cfl

Display WA #1183 was recently added to workaround
"Failures when enabling DPLL0 with eDP link rate 2.16
or 4.32 GHz and CD clock frequency 308.57 or 617.14 MHz
(CDCLK_CTL CD Frequency Select 10b or 11b) used in this
 enabling or in previous enabling."

This workaround was designed to minimize the impact only
to save the bad case with that link rates. But HW engineers
indicated that it should be safe to apply broadly, although
they were expecting the DPLL0 link rate to be unchanged on
runtime.

We need to cover 2 cases: when we are in fact enabling DPLL0
and when we are just changing the frequency with small
differences.

This is based on previous patch by Rodrigo Vivi with suggestions
from Ville Syrjälä.

Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171204232210.4958-1-lucas.demarchi@intel.com

drm/i915: Update DRIVER_DATE to 20171222

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915: Show HWSP in intel_engine_dump()

Looking at a CI failure with an ominous line of
[  362.550715] hangcheck current seqno ffffff6b, last ffffff8c, hangcheck ffffff6b [6016 ms], inflight 118
with no apparent cause for the seqno to be negative, left me wondering
if someone had scribbled over the HWSP. So include the HWSP in the
engine dump to see if there are more signs of random scribbling.

v2: Fix row pointer, i is now incremented by 8 so doesn't need scaling
by 8, and we don't need to keep volatile here as the status_page isn't
marked up as volatile itself.
v3: Use hexdump, with suppression of identical lines. (Tvrtko)
    Which results in

HWSP:
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
*
00000040 00000001 00000000 00000018 00000002 00000001 00000000 00000018 00000000
00000060 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000003
00000080 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
*
000000c0 00000002 00000000 00000000 00000000 00000000 00000000 00000000 00000000
000000e0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
*

    instead of 128 lines of mostly 0s.
v4: Tidy up the locals

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222182521.18106-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Assert that the request is on the execution queue before being removed

We should only attempt to remove requests from the execution queue that
are on the execution queue. These are the requests that have been
assigned a global_seqno, so we can assert that we only attempt to remove
requests with a nonzero global_seqno. Afterwards we assert that we
remove them in order, i.e. the global_seqno matches the engine's seqno,
but that leaves a small loophole for an unattached request on an unused
engine.

We can then make the same assertion on queuing the request to the
execution engine, it must have a zero global_seqno or else we are queuing
the same request twice.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222141959.3006-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915/execlists: Show preemption progress in GEM_TRACE

We already emit a GEM_TRACE for when we start preemption, but we lack
one to show when the preemption is completed and we return to the regular
queue. This is to continue the investigation into the mysterious

<0>[  197.854177]   <idle>-0       1..s1 197837017us : execlists_submission_tasklet: rcs0 cs-irq head=0 [0], tail=0 [0]
<0>[  197.854209] drv_self-6008    2.... 197837390us : reset_common_ring: rcs0 seqno=15515
<0>[  197.854240] drv_self-6008    2.... 197837415us : reset_common_ring: bcs0 seqno=0
<0>[  197.854270] drv_self-6008    2.... 197837443us : reset_common_ring: vcs0 seqno=0
<0>[  197.854300] drv_self-6008    2.... 197837463us : reset_common_ring: vcs1 seqno=0
<0>[  197.854330] drv_self-6008    2.... 197837482us : reset_common_ring: vecs0 seqno=0
<0>[  197.854360] ksoftirq-23      2..s. 197838341us : execlists_submission_tasklet: bcs0 in[0]:  ctx=0.1, seqno=1dce7
<0>[  197.854392]   <idle>-0       1..s1 197838347us : execlists_submission_tasklet: bcs0 cs-irq head=0 [0], tail=0 [0]
<0>[  197.854423] ksoftirq-23      2..s. 197838354us : execlists_submission_tasklet: vcs0 in[0]:  ctx=0.1, seqno=1d027
<0>[  197.854456] ksoftirq-23      2.Ns. 197838361us : execlists_submission_tasklet: vcs1 in[0]:  ctx=0.1, seqno=1e738
<0>[  197.854488] ksoftirq-23      2.Ns. 197838366us : execlists_submission_tasklet: vecs0 in[0]:  ctx=0.1, seqno=235aa
<0>[  197.854520] ksoftirq-23      2.Ns. 197838376us : execlists_submission_tasklet: rcs0 in[0]:  ctx=0.1, seqno=15518
<0>[  197.854552]   <idle>-0       1..s1 197853285us : execlists_submission_tasklet: rcs0 cs-irq head=0 [0], tail=7 [7]
<0>[  197.854584]   <idle>-0       1..s1 197853285us : execlists_submission_tasklet: rcs0 csb[1]: status=0x00000018:0x00000000
<0>[  197.854616]   <idle>-0       1..s1 197853286us : execlists_submission_tasklet: rcs0 out[0]: ctx=0.0, seqno=0

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222132742.4272-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

Merge tag 'gvt-next-2017-12-22' of https://github.com/intel/gvt-linux into drm-intel-next-queued

gvt-next-2017-12-22:

- more mmio switch optimization (Weinan)
- cleanup i915_reg_t vs. offset usage (Zhenyu)
- move write protect handler out of mmio handler (Zhenyu)

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222085141.vgewlvvni37dljdt@zhen-hp.sh.intel.com

drm/i915: Put all non-blocking modesets onto an ordered wq

We have plenty of global registers and whatnot programmed without
any further locking by the modeset code. Currently non-bocking
modesets are allowed to execute in parallel which could corrupt
said registers.

To avoid the problem let's run all non-blocking modesets on an
ordered workqueue. We still put page flips etc. to system_unbound_wq
allowing page flips on one pipe to execute in parallel with page flips
or a modeset on a another pipe (assuming no known state is shared
between them, at which point they would have been added to the same
atomic commit and serialized that way).

Blocking modesets are already serialized with each other by
connection_mutex, and thus are safe. To serialize them with
non-blocking modesets we just flush the workqueue before executing
blocking modesets.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 94f050246b42 ("drm/i915: nonblocking commit")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171113133622.8593-1-ville.syrjala@linux.intel.com
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Disable GMBUS clock gating around GMBUS transfers on gen9+

Gen9+ need to disable GMBUS clock gating when doing multi part
transfers. Otherwise clock gating will kick in when GMBUS is in
the WAIT state and presumably that will corrupt the transfer.
This is documented as Display WA #0868.

Apparently older hardware doesn't allow clock gating in the WAIT
state and thus are unaffected by this problem.

v2: Limit the PCH w/a to gen9 and gen10 only (DK)
    Actually change it to check the PCH type instead since
    it's the PCH that actually contains the GMBUS hardware

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20171221202432.17373-1-ville.syrjala@linux.intel.com

drm/i915: Clean up the PNV bit banging vs. GMBUS clock gating w/a

Give a proper name for the GMBUS clock gating disable bit on PNV,
and rename intel_i2c_quirk_set() to pnv_gmbus_clock_gating() for
clarity.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171208213739.16388-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: No need to power up PG2 for GMBUS on BXT

GMBUS lives in PG1, so no need to power up PG2. We do want to prevent
the DMC from making a mess of things though, so add GMBUS to the DC off
power well.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171208213739.16388-2-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>

drm/i915: Disable DC states around GMBUS on GLK

Prevent the DMC from destroying GMBUS transfers on GLK. GMBUS
lives in PG1 so DC off is all we need.

Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171208213739.16388-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>

drm/i915: Do not enable movntdqa optimization in hypervisor guest

Our QA reported a problem caused by movntdqa instructions. Currently,
the KVM hypervisor doesn't support VEX-prefix instructions emulation.
If users passthrough a GPU to guest with vfio option 'x-no-mmap=on',
then all access to the BARs will be trapped and emulated. The KVM
hypervisor would raise an inertal error to qemu which cause the guest
killed. (Since 'movntdqa' ins is not supported.)

This patch try not to enable movntdqa optimization if the driver is
running in hypervisor guest.

Signed-off-by: Changbin Du <changbin.du@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1513924309-3113-1-git-send-email-changbin.du@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Dump device info at once

We are dumping device info separately for sw_only and runtime part
but to simplify the code we can also do it from one place once
we complete driver load.

v2: use dedicated welcome function (Chris)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171221185334.17396-8-michal.wajdeczko@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171221215735.30314-7-chris@chris-wilson.co.uk

drm/i915: Add pretty printer for runtime part of intel_device_info

During initialization of the runtime part of the intel_device_info
we are dumping that part using DRM_DEBUG_DRIVER mechanism.
As we already have pretty printer for const part of the info,
make similar function for the runtime part and use it separately.

v2: add runtime dump to debugfs (Chris)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171221185334.17396-7-michal.wajdeczko@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171221215735.30314-6-chris@chris-wilson.co.uk

drm/i915: Update intel_device_info_runtime_init() parameter

As we try to follow object-verb pattern in our functions, update
intel_device_info_runtime_init() parameter from dev_priv to info.

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171221185334.17396-6-michal.wajdeczko@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171221215735.30314-5-chris@chris-wilson.co.uk

drm/i915: Move intel_device_info definitions to its own header

We already keep intel_device_info functions in dedicated file.
Add matching header file and move related definitions there.

v2: add gen boundaries (Chris)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171221185334.17396-5-michal.wajdeczko@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171221215735.30314-4-chris@chris-wilson.co.uk

drm/i915: Move opregion definitions to dedicated intel_opregion.h

We already have dedicated file for opregion related code, dedicated
header will make our life easier.

v2: reorder includes (Chris)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171221185334.17396-4-michal.wajdeczko@intel.com
[ickle: quieten checkpatch]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171221215735.30314-3-chris@chris-wilson.co.uk

drm/i915: Move display related definitions to dedicated header

We already have separate files for display related code, there
is no reason to keep all display definitions in master header.

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171221185334.17396-3-michal.wajdeczko@intel.com
[ickle: quieten checkpatch]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171221215735.30314-2-chris@chris-wilson.co.uk

drm/i915: Move some utility functions to i915_util.h

We have dedicated header file for utility functions and macros.

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171221185334.17396-2-michal.wajdeczko@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171221215735.30314-1-chris@chris-wilson.co.uk

drm/i915/gvt: move write protect handler out of mmio emulation function

It's a bit confusing that page write protect handler is live in
mmio emulation handler. This moves it to stand alone gvt ops.

Also remove unnecessary check of write protected page access
in mmio read handler and cleanup handling of failsafe case.

v2: rebase

Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: cleanup usage for typed mmio reg vs. offset

We had previous hack that tried to accept either i915_reg_t or offset
value to access vGPU virtual/shadow regs which broke that purpose to
be type safe in context. This one trys to explicitly separate the usage
of typed mmio reg with real offset.

Old vgpu_vreg(offset) helper is used only for offset now with new
vgpu_vreg_t(reg) is used for i915_reg_t only. Convert left usage
of that to new helper.

Also fixed left KASAN warning issues caused by previous hack.

v2: rebase, fixup against recent mmio switch change

Reviewed-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Fix pipe A enable as default for vgpu

observed igt drv_module_reload test case failure on 4.15.0
rc2 kernel with panic due to no active pipe available.

the gpu will reset during unload/load and make pipe config reg
lost which can cause kernel panic issue happen.

this patch is to move pipe enabling to emulate_mointor_status_chagne
to handle vgpu reset case as well.

Fixes: 7e6059020894 ("drm/i915/gvt: enabled pipe A default on creating vgpu")
Signed-off-by: Xiaolin Zhang <xiaolin.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
(cherry picked from commit f5f00e7dcc4161f07b76ff1a854e8b1ea7a1ed41)

drm/i915/gvt: always use i915_reg_t for MMIO handler definition

Always requires properly defined i915_reg_t type for MMIO handler
definition.

Fix kasan warning of "drivers/gpu/drm/i915/gvt/handlers.c:2397:1: error: the frame size of 32120 bytes is larger than 8192 bytes"

Reviewed-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915: Show FBC worker status in debugfs

Include the pending update from the FBC worker in i915_fbc_status.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171220205848.8510-1-chris@chris-wilson.co.uk
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>

drm/i915: Disable all planes for load detection, v2.

We don't need any active planes during load detection, so just disable
them all. This saves us from having to come up with a suitable
framebuffer. And we also avoid leaving sprite/cursor planes on and
potentially presenting them at a peculiar location during the load
detection.

Changes since v1 (Maarten):
- Add missing call to add_all_affected_planes.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102707
Link: https://patchwork.freedesktop.org/patch/msgid/20171220093545.613-4-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

i915: Reject CCS modifiers for pipe C on Geminilake

Current code advertises (on the modifiers blob property) support for CCS
modifier for pipe C on GLK, only to reject it later when validating the
request before the atomic commit.

This fixes the tests igt@kms_ccs@pipe-c-*, which should skip on GLK for
pipe C (see bug 104096).

A relevant discussion is archived at:

https://lists.freedesktop.org/archives/intel-gfx/2017-December/150646.html

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104096
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171220002410.5604-1-krisman@collabora.co.uk

drm/i915/cfl: Adding more Coffee Lake PCI IDs.

Spec has been updated with more reserved IDs for existent SKUs.

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Anuj Phogat <anuj.phogat@gmail.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa<anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171220182919.21108-1-rodrigo.vivi@intel.com

drm/i915: Tidy up GEM_TRACE around execlists

Looking at the coordination of resets with the submission of execlists,
it will be useful to have a GEM_TRACE for when we issue the reset.
Whilst there tidy up the other GEM_TRACE to always include the engine
name, and be careful not to trust any pointers prior to asserts.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171220090626.31643-1-chris@chris-wilson.co.uk

drm/i915/psr: Fix register name mess up.

Commit 77affa31722b ("drm/i915/psr: Fix compiler warnings for
hsw_psr_disable()") swapped status and control registers while fixing
indentation. The _ctl at the end of the status register name must have to
led to this.

Fixes: 77affa31722b ("drm/i915/psr: Fix compiler warnings for hsw_psr_disable()")
References: https://www.mrc-cbu.cam.ac.uk/people/matt.davis/cmabridge/
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171220043520.2599-1-dhinakaran.pandiyan@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Avoid context dereference inside execlists_submission_tasklet

A lesson that has to be relearnt over and over again is that the request
does not keep a reference to the context and so we cannot freely
dereference the context from inside the execlists_submission_tasklet. In
particular, we try to do so in the new GEM_TRACE() so convert those over
to the port->context_id we keep for GEM debugging. This means the
tracing now depends on DRM_I915_GEM_DEBUG.

Fixes: bccd3b831185 ("drm/i915: Use trace_printk to provide a death rattle for GEM")
References: https://bugs.freedesktop.org/show_bug.cgi?id=104066
References: https://bugs.freedesktop.org/show_bug.cgi?id=104162
References: https://bugs.freedesktop.org/show_bug.cgi?id=104242
References: https://bugs.freedesktop.org/show_bug.cgi?id=104310
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171219220916.30882-1-chris@chris-wilson.co.uk

drm/i915: Remove pointer indirection for hangcheck_state local

Use the local on-stack struct directly rather than hide it behind a
pointer. This should be both clearer for the reader and the compiler (we
rely on the compiler seeing through the functions to spot uninitialized
uses of the local).

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171219130948.6282-1-chris@chris-wilson.co.uk

drm/i915: Show if we consider the engine is idle in the GPU error state

Useful for verifying our bookkeeper when we encounter is knowing whether
we think the engine is idle at the time of the GPU hang.

References: https://bugs.freedesktop.org/show_bug.cgi?id=104305
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171219131419.13117-1-chris@chris-wilson.co.uk

drm/i915: Implement WaDisableEarlyEOT.

There seems to be another clock gating issue which the workaround is
described as:

   "WA: Set 0xE4F0[1] = 1 to disable Early EOT of thread."

Signed-off-by: Rafael Antognolli <rafael.antognolli@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171216001117.14232-2-rafael.antognolli@intel.com

drm/i915: Implement WaDisableVFclkgate.

This workaround supposedly fixes some hangs in the VF unit.

Signed-off-by: Rafael Antognolli <rafael.antognolli@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171216001117.14232-1-rafael.antognolli@intel.com

drm/i915: Add pretty printer for modparams

We dump modparams in few places (debugfs, gpu_error) using different
functions. Lets add reusable function to avoid code duplication.

add/remove: 1/0 grow/shrink: 0/2 up/down: 1096/-2339 (-1243)
Function                                     old     new   delta
i915_params_dump                               -    1096   +1096
i915_capabilities                           1353     185   -1168
i915_error_state_to_str                     5507    4336   -1171
Total: Before=1285716, After=1284473, chg -0.10%

v2: use forward decl rather than include (Chris)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171219114346.26308-3-michal.wajdeczko@intel.com

drm/i915: Convert intel_device_info_dump into pretty printer

Convert intel_device_info_dump into pretty printer to be
consistent with the rest of the driver code.

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171219114346.26308-2-michal.wajdeczko@intel.com

drm/i915: Add pretty printer for device info flags

We dump device flags in few places (init_early, debugfs, gpu_error)
using different functions. Lets add reusable function to avoid
code duplication.

add/remove: 1/0 grow/shrink: 0/3 up/down: 1296/-3572 (-2276)
Function                                     old     new   delta
intel_device_info_dump_flags                   -    1296   +1296
i915_capabilities                           2435    1353   -1082
i915_error_state_to_str                     6642    5507   -1135
intel_device_info_dump                      1507     152   -1355
Total: Before=1287992, After=1285716, chg -0.18%

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171219114346.26308-1-michal.wajdeczko@intel.com

drm/i915: Fix indentation for intel_ddi_clk_select

drivers/gpu/drm/i915/intel_ddi.c:2098 intel_ddi_clk_select() warn: inconsistent indenting

References: 8edcda1266f9 ("drm/i915: Protect DDI port to DPLL map from theoretical race.")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171219112649.9388-1-chris@chris-wilson.co.uk

drm/i915: Add a strong mb to resetting the has-CS-interrupt bit

After a reset, the state of the CSB registers are scrubbed and not valid
until a powercontext is reloaded. We only know when a powercontext has
been reloaded once we see a CS-interrupt, before then we must ignore the
CSB registers within the execlists_submission_tasklet. However, glk is
sporadically dying with an illegal CSB pointer value (both in the HSWP
and mmio) suggesting that it is running with the CS-interrupt bit set
before the powercontext has been reloaded. Make sure the clearing of
that bit is serialised on reset with the re-enabling of the tasklet.

References: https://bugs.freedesktop.org/show_bug.cgi?id=104262
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171219090110.11153-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915/cnl: Add support for horizontal plane flipping

CNL supports horizontal plane flipping on non-linear plane formats.

v2:
- Avoid BUG unlike elsewhere in the code (Ville)
- Hoist the rotation-tiling restriction check (Ville)

v3 (Rodrigo):
- Rebased after a while.
- Fix small indentation issues.

Bspec: 7656
Suggested-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171215213800.7896-1-rodrigo.vivi@intel.com

drm/i915: Protect DDI port to DPLL map from theoretical race.

In case we have multiple modesets for different connectors
happening in parallel we could have a race on the RMW on these
shared registers.

This possibility was initially raised by Paulo when reviewing
commit '555e38d27317 ("drm/i915/cnl: DDI - PLL mapping")'
but the original possibility comes from commit '5416d871136d
("drm/i915/skl: Set the eDP link rate on DPLL0")'. Or maybe
later when atomic commits entered into picture.

Apparently the discussion around this topic showed that the
right solution would be on serializing the atomic commits in
a way that we don't have the possibility of races here since
if that parallel modeset happenings apparently many other
things will be on fire.

Code is there since SKL and there was no report of issue,
but since we never looked back to that serialization possibility,
and also we don't have an igt case for that it is better to at
least protect this corner.

Suggested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Fixes: 555e38d27317 ("drm/i915/cnl: DDI - PLL mapping")
Fixes: 5416d871136d ("drm/i915/skl: Set the eDP link rate on DPLL0")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst maarten.lankhorst@linux.intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst maarten.lankhorst@linux.intel.com
Link: https://patchwork.freedesktop.org/patch/msgid/20171215224310.19103-1-rodrigo.vivi@intel.com

drm/i915/selftests: Fix up igt_reset_engine

Now that we skip a per-engine reset on an idle engine, we need to update
the selftest to take that into account. In the process, we find that we
were not stressing the per-engine reset very hard, so add those missing
active resets.

v2: Actually test i915_reset_engine() by loading it with requests.

Fixes: f6ba181ada55 ("drm/i915: Skip an engine reset if it recovered before our preparations")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104313
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171217132852.30642-3-chris@chris-wilson.co.uk
Reviewed-by: Michel Thierry <michel.thierry@intel.com>

drm/i915/trace: add hw_id to gem requests trace points

When monitoring the GPU with i915 perf, reports are tagged with a hw
id. Gem context creation tracepoints already have a hw_id field,
unfortunately you only get this correlation between a process id and a
hw context id once when the context is created. It doesn't help if you
started monitoring after the process was initialized or if the drm fd
was transfered from one process to another.

This change adds the hw_id field to gem requests, so that correlation
can also be done on submission.

v2: Place hw_id at the end of the tracepoint to not disrupt too much
    existing tools (Chris)

v3: Reorder hw_id field again (Chris)

v4: Add missing hw_id to i915_gem_request_wait_begin tracepoint (Chris)

Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171218151959.14073-3-lionel.g.landwerlin@intel.com

drm/i915: reorder field in gem_request tracepoints

Let's make the order of the fields of the tracepoints involving gem
request match across i915. This makes userspace processing of
tracepoint a bit easier.

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171218151959.14073-2-lionel.g.landwerlin@intel.com

drm/i915: Show IPEIR and IPEHR in the engine dump

A useful bit of information for inspecting GPU stalls from
intel_engine_dump() are the error registers, IPEIR and IPEHR.

v2: Fixup gen changes in register offsets (Tvrtko)
v3: Old FADDR location as well
v4: Use I915_READ64_2x32

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171218123914.19027-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: prefer i915_gem_object_has_pages()

We have an existing helper for testing obj->mm.pages, so use it.

Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171218103855.25274-1-matthew.auld@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Re-enable GGTT earlier after GPU reset

Inside i915_gem_reset(), we start touching the HW and so require the
low-level HW to be re-enabled, in particular the PCI BARs.

Fixes: 7b6da818d86f ("drm/i915: Restore the kernel context after a GPU reset on an idle engine")
References: 0db8c9612091 ("drm/i915: Re-enable GTT following a device reset")
Testcase: igt/drv_hangman #i915g/i915gm
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171217132852.30642-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915/gvt: load host render mocs once in mocs switch

Load host render mocs registers once for delta update of mocs switch, it
reduces mmio read times obviously, then brings performance improvement
during multi-vms switch.

Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: refine mocs save restore policy

Save and restore the mocs regs of one VM in GVT-g burning too much CPU
utilization. Add LRI command scan to monitor the change of mocs registers,
save the state in vreg, and use delta update policy to restore them.
It can obviously reduce the MMIO r/w count, and improve the performance
of context switch.

Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: optimize for vGPU mmio switch

Now mmio switch between vGPUs need to switch to host first then to expected
vGPU, it waste one time mmio save/restore. r/w mmio usually is
time-consuming, and there are so many mocs registers need to save/restore
during vGPU switch. Combine the switch_to_host and switch_to_vgpu can
reduce 1 time mmio save/restore, it will reduce the CPU utilization and
performance while there is multi VMs with heavy work load.

Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: refine trace_render_mmio

Refine trace_render_mmio to show the vm id before and after vgpu switch,
tag host id as '0', this patch will be used in the future patch for refine
mocs switch policy.

Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

Merge tag 'drm-intel-next-2017-12-14' into gvt-next

- Fix documentation build issues (Randy, Markus)
- Fix timestamp frequency calculation for perf on CNL (Lionel)
- New DMC firmware for Skylake (Anusha)
- GTT flush fixes and other GGTT write track and refactors (Chris)
- Taint kernel when GPU reset fails (Chris)
- Display workarounds organization (Lucas)
- GuC and HuC initialization clean-up and fixes (Michal)
- Other fixes around GuC submission (Michal)
- Execlist clean-ups like caching ELSP reg offset and improving log readability (Chri\
s)
- Many other improvements on our logs and dumps (Chris)
- Restore GT performance in headless mode with DMC loaded (Tvrtko)
- Stop updating legacy fb parameters since FBC is not using anymore (Daniel)
- More selftest improvements (Chris)
- Preemption fixes and improvements (Chris)
- x86/early-quirks improvements for Intel graphics stolen memory. (Joonas, Matthew)
- Other improvements on Stolen Memory code to be resource centric. (Matthew)
- Improvements and fixes on fence allocation/release (Chris).

GVT:

- fixes for two coverity scan errors (Colin)
- mmio switch code refine (Changbin)
- more virtual display dmabuf fixes (Tina/Gustavo)
- misc cleanups (Pei)
- VFIO mdev display dmabuf interface and gvt support (Tina)
- VFIO mdev opregion support/fixes (Tina/Xiong/Chris)
- workload scheduling optimization (Changbin)
- preemption fix and temporal workaround (Zhenyu)
- and misc fixes after refactor (Chris)

drm/i915: Unifying debugfs return codes for unsupported features

Instead of trying different seq_puts messages, lets use common
-ENODEV error code to indicate missing/unsupported feature.

v2: don't forget about guc_log_control fops (Sagar)

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Sujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171215143635.17884-1-michal.wajdeczko@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Restore the kernel context after a GPU reset on an idle engine

As part of the system requirement for powersaving is that we always have
a context loaded. Upon boot and resume, we load the kernel_context to
ensure that some valid state is set before powersaving kicks in, we
should do so after a full GPU reset as well. We only need to do so for
an idle engine, as any active engines will restart by executing the
stuck request, loading its context. For the idle engine, we create a
new request to load the kernel_context instead.

For whatever reason, perfoming a dummy execute on the idle engine after
reset papers over a subsequent GPU hang in rare circumstances, even on
machines not using contexts (e.g. Pineview).

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104259
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104261
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171216000334.8197-1-chris@chris-wilson.co.uk

drm/i915: Skip an engine reset if it recovered before our preparations

At the beginning of a reset, we disable the submission method and find
the stuck request. We expect to find a stuck request for we have
declared the engine stalled. However, if we find no active request, the
engine must have recovered from its stall before we could issue a reset,
so let the engine continue on without a reset. If the engine is truly
stuck, we will back soon enough with the next reset attempt.

v2: Remove the stale debug message.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171216002206.31737-1-chris@chris-wilson.co.uk

x86/gpu: add CFL to early quirks

CFL was missing from intel_early_ids[]. The PCI ID needs to be there to
allow the memory region to be stolen, otherwise we could have RAM being
arbitrarily overwritten if for example we keep using the UEFI framebuffer,
depending on how BIOS has set up the e820 map.

Fixes: b056f8f3d6b9 ("drm/i915/cfl: Add Coffee Lake PCI IDs for S Skus.")
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86@kernel.org
Cc: <stable@vger.kernel.org> # v4.13+ 0890540e21cf drm/i915: add GT number to intel_device_info
Cc: <stable@vger.kernel.org> # v4.13+ 41693fd52373 drm/i915/kbl: Change a KBL pci id to GT2 from GT1.5
Cc: <stable@vger.kernel.org> # v4.13+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213200425.2954-1-lucas.demarchi@intel.com

drm/i915/lpe: Remove double-encapsulation of info string

Just printk the string, or at least do not double up on the newlines!

Fixes: eef57324d926 ("drm/i915: setup bridge for HDMI LPE audio driver")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Jerome Anand <jerome.anand@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213182858.2159-1-chris@chris-wilson.co.uk

drm/i915: Allow internal page allocations to fail

Internal objects consistent of scratch pages not subject to the
persistence guarantees of user facing objects. They are used for
example, in ring buffers where they are only required for temporary
storage of commands that will be rewritten every time. As they are
temporary constructs, quietly report -ENOMEM back along the callchain
rather than subject the system to oomkiller if an allocation fails.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171215101753.1519-1-chris@chris-wilson.co.uk

drm/i915: Update DRIVER_DATE to 20171214

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Merge tag 'gvt-next-2017-12-14' of https://github.com/intel/gvt-linux into drm-intel-next-queued

gvt-next-2017-12-14:

- fixes for two coverity scan errors (Colin)
- mmio switch code refine (Changbin)
- more virtual display dmabuf fixes (Tina/Gustavo)
- misc cleanups (Pei)

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171214033434.jlppjlyal5d67ya7@zhen-hp.sh.intel.com

drm/i915: properly init lockdep class

The code has an ifdef and uses two functions to either init the bare
spinlock or init it and set a lock-class. It is possible to do the same
thing without an ifdef.
With this patch (in debug case) we first use the "default" lock class
which is later overwritten to the supplied one. Without lockdep the set
name/class function vanishes.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171214131009.7479-1-joonas.lahtinen@linux.intel.com
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Show engine state when hangcheck detects a stall

Knowing the state of the engine when hangcheck thinks it is stalling is
useful for both debugging hangcheck itself and the potential cause of an
unwanted stall.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171214122613.26134-1-chris@chris-wilson.co.uk

drm/i915: make CS frequency read support missing more obvious

As suggested by Chris, we should make this more obvious for people
working with newer generations.

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213171154.6201-1-lionel.g.landwerlin@intel.com

drm/i915/guc: Extract doorbell verification into a function

We have the selftest that's checking doorbell create/destroy, so there's
no need to check all doorbells delaying the reset every time.
We do want to have that extra sanity check at module load/unload though.

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213221352.7173-7-michal.winiarski@intel.com

drm/i915/guc: Extract clients allocation to submission_init

We can now move the clients allocation to submission_init path, rather
than keeping the condition inside submission_enable called on every
reset.

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213221352.7173-6-michal.winiarski@intel.com

drm/i915/guc: Extract doorbell creation from client allocation

Full GPU reset causes GuC to be reset. This means that every time we're
doing a reset, we need to talk to GuC and tell it about doorbells.
Let's separate the communication part (create_doorbell) from our
internal bookkeeping (reserve_doorbell) so that we can cleanly separate
the initialization done at module load from reinitialization done at
reset in the following patch.
While I'm here, let's also add a proper (although slightly asymetric)
cleanup that doesn't try to communicate with GuC after it's already
gone, getting rid of "expected" warnings caused by GuC action failures
on module unload.

Note that I've also removed one of the tests (bitmap out of sync), since
it doesn't make much sense anymore - bitmaps are now not expected to
change during the lifetime of a client.

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213221352.7173-5-michal.winiarski@intel.com

drm/i915/guc: Call invalidate after changing the vfunc

To make this operation a bit cleaner, we should make sure that the HW
can catch up by calling the new implementation right away.
Note that currently we're only touching the vfunc at module load time
(before GuC is even loaded), so this shouldn't cause any functional
changes.

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213221352.7173-4-michal.winiarski@intel.com

drm/i915/guc: Extract guc_init from guc_init_hw

After GPU reset, GuC HW needs to be reinitialized (with FW reload).
Unfortunately, we're doing some extra work there (mostly allocating stuff),
work that can be moved to guc_init and called once at driver load time.

As a side effect we're no longer hitting an assert in
i915_ggtt_enable_guc on suspend/resume.

v2: Do not duplicate disable_communication / reset_guc_interrupts
v3: Add proper teardown after rebase

References: 04f7b24eccdf ("drm/i915/guc: Assert that we switch between known ggtt->invalidate functions")
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213221352.7173-3-michal.winiarski@intel.com

drm/i915/guc: Move GuC workqueue allocations outside of the mutex

This gets rid of the following lockdep splat:

======================================================
WARNING: possible circular locking dependency detected
4.15.0-rc2-CI-Patchwork_7428+ #1 Not tainted
------------------------------------------------------
debugfs_test/1351 is trying to acquire lock:
 (&dev->struct_mutex){+.+.}, at: [<000000009d90d1a3>] i915_mutex_lock_interruptible+0x47/0x130 [i915]

but task is already holding lock:
 (&mm->mmap_sem){++++}, at: [<000000005df01c1e>] __do_page_fault+0x106/0x560

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #6 (&mm->mmap_sem){++++}:
       __might_fault+0x63/0x90
       _copy_to_user+0x1e/0x70
       filldir+0x8c/0xf0
       dcache_readdir+0xeb/0x160
       iterate_dir+0xe6/0x150
       SyS_getdents+0xa0/0x130
       entry_SYSCALL_64_fastpath+0x1c/0x89

-> #5 (&sb->s_type->i_mutex_key#5){++++}:
       lockref_get+0x9/0x20

-> #4 ((completion)&req.done){+.+.}:
       wait_for_common+0x54/0x210
       devtmpfs_create_node+0x130/0x150
       device_add+0x5ad/0x5e0
       device_create_groups_vargs+0xd4/0xe0
       device_create+0x35/0x40
       msr_device_create+0x22/0x40
       cpuhp_invoke_callback+0xc5/0xbf0
       cpuhp_thread_fun+0x167/0x210
       smpboot_thread_fn+0x17f/0x270
       kthread+0x173/0x1b0
       ret_from_fork+0x24/0x30

-> #3 (cpuhp_state-up){+.+.}:
       cpuhp_issue_call+0x132/0x1c0
       __cpuhp_setup_state_cpuslocked+0x12f/0x2a0
       __cpuhp_setup_state+0x3a/0x50
       page_writeback_init+0x3a/0x5c
       start_kernel+0x393/0x3e2
       secondary_startup_64+0xa5/0xb0

-> #2 (cpuhp_state_mutex){+.+.}:
       __mutex_lock+0x81/0x9b0
       __cpuhp_setup_state_cpuslocked+0x4b/0x2a0
       __cpuhp_setup_state+0x3a/0x50
       page_alloc_init+0x1f/0x26
       start_kernel+0x139/0x3e2
       secondary_startup_64+0xa5/0xb0

-> #1 (cpu_hotplug_lock.rw_sem){++++}:
       cpus_read_lock+0x34/0xa0
       apply_workqueue_attrs+0xd/0x40
       __alloc_workqueue_key+0x2c7/0x4e1
       intel_guc_submission_init+0x10c/0x650 [i915]
       intel_uc_init_hw+0x29e/0x460 [i915]
       i915_gem_init_hw+0xca/0x290 [i915]
       i915_gem_init+0x115/0x3a0 [i915]
       i915_driver_load+0x9a8/0x16c0 [i915]
       i915_pci_probe+0x2e/0x90 [i915]
       pci_device_probe+0x9c/0x120
       driver_probe_device+0x2a3/0x480
       __driver_attach+0xd9/0xe0
       bus_for_each_dev+0x57/0x90
       bus_add_driver+0x168/0x260
       driver_register+0x52/0xc0
       do_one_initcall+0x39/0x150
       do_init_module+0x56/0x1ef
       load_module+0x231c/0x2d70
       SyS_finit_module+0xa5/0xe0
       entry_SYSCALL_64_fastpath+0x1c/0x89

-> #0 (&dev->struct_mutex){+.+.}:
       lock_acquire+0xaf/0x200
       __mutex_lock+0x81/0x9b0
       i915_mutex_lock_interruptible+0x47/0x130 [i915]
       i915_gem_fault+0x201/0x760 [i915]
       __do_fault+0x15/0x70
       __handle_mm_fault+0x85b/0xe40
       handle_mm_fault+0x14f/0x2f0
       __do_page_fault+0x2d1/0x560
       page_fault+0x22/0x30

other info that might help us debug this:

Chain exists of:
  &dev->struct_mutex --> &sb->s_type->i_mutex_key#5 --> &mm->mmap_sem

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&mm->mmap_sem);
                               lock(&sb->s_type->i_mutex_key#5);
                               lock(&mm->mmap_sem);
  lock(&dev->struct_mutex);

 *** DEADLOCK ***

1 lock held by debugfs_test/1351:
 #0:  (&mm->mmap_sem){++++}, at: [<000000005df01c1e>] __do_page_fault+0x106/0x560

stack backtrace:
CPU: 2 PID: 1351 Comm: debugfs_test Not tainted 4.15.0-rc2-CI-Patchwork_7428+ #1
Hardware name:                  /NUC6i5SYB, BIOS SYSKLi35.86A.0057.2017.0119.1758 01/19/2017
Call Trace:
 dump_stack+0x5f/0x86
 print_circular_bug+0x230/0x3b0
 check_prev_add+0x439/0x7b0
 ? lockdep_init_map_crosslock+0x20/0x20
 ? unwind_get_return_address+0x16/0x30
 ? __lock_acquire+0x1385/0x15a0
 __lock_acquire+0x1385/0x15a0
 lock_acquire+0xaf/0x200
 ? i915_mutex_lock_interruptible+0x47/0x130 [i915]
 __mutex_lock+0x81/0x9b0
 ? i915_mutex_lock_interruptible+0x47/0x130 [i915]
 ? i915_mutex_lock_interruptible+0x47/0x130 [i915]
 ? i915_mutex_lock_interruptible+0x47/0x130 [i915]
 i915_mutex_lock_interruptible+0x47/0x130 [i915]
 ? __pm_runtime_resume+0x4f/0x80
 i915_gem_fault+0x201/0x760 [i915]
 __do_fault+0x15/0x70
 __handle_mm_fault+0x85b/0xe40
 handle_mm_fault+0x14f/0x2f0
 __do_page_fault+0x2d1/0x560
 page_fault+0x22/0x30
RIP: 0033:0x7f98d6f49116
RSP: 002b:00007ffd6ffc3278 EFLAGS: 00010283
RAX: 00007f98d39a2bc0 RBX: 0000000000000000 RCX: 0000000000001680
RDX: 0000000000001680 RSI: 00007ffd6ffc3400 RDI: 00007f98d39a2bc0
RBP: 00007ffd6ffc33a0 R08: 0000000000000000 R09: 00000000000005a0
R10: 000055e847c2a830 R11: 0000000000000002 R12: 0000000000000001
R13: 000055e847c1d040 R14: 00007ffd6ffc3400 R15: 00007f98d6752ba0

v2: Init preempt_work unconditionally (Chris)
v3: Mention that we need the enable_guc=1 for lockdep splat (Chris)

Testcase: igt/debugfs_test/read_all_entries # with i915.enable_guc=1
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213221352.7173-2-michal.winiarski@intel.com

drm/i915/guc: Move shared data allocation away from submission path

We need shared data for actions (e.g. guc suspend/resume), and we're
using those with GuC submission disabled.
Let's introduce intel_guc_init and move shared data alloc there.

This fixes GPF during module unload with HuC, but without GuC submission:

BUG: unable to handle kernel NULL pointer dereference at 000000005aee7809
IP: intel_guc_suspend+0x34/0x140 [i915]
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: i915(O-) netconsole x86_pkg_temp_thermal
intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul ghash_clmulni_intel
mei_me i2c_i801 mei prime_numbers [last unloaded: i915]
CPU: 2 PID: 2794 Comm: rmmod Tainted: G     U  W  O 4.15.0-rc2+ #297
Hardware name: /NUC6i5SYB, BIOS SYSKLi35.86A.0054.2016.0930.1102 09/30/2016
task: 0000000055945c61 task.stack: 00000000264ccb43
RIP: 0010:intel_guc_suspend+0x34/0x140 [i915]
RSP: 0018:ffffc90000483df8 EFLAGS: 00010286
RAX: 0000000000000000 RBX: ffff880829180000 RCX: 0000000000000000
RDX: 0000000000000006 RSI: ffff880844c2c938 RDI: ffff880844c2c000
RBP: ffff880829180000 R08: 00000000a29c58c1 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffffffffa040ba40
R13: ffffffffa040bab0 R14: ffff88084a195060 R15: 000055df3ef357a0
FS:  00007ff43c043740(0000) GS:ffff88084e200000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000000f9 CR3: 000000083f179005 CR4: 00000000003606e0
Call Trace:
 i915_gem_suspend+0x9d/0x130 [i915]
 ? i915_driver_unload+0x68/0x180 [i915]
 i915_driver_unload+0x70/0x180 [i915]
 i915_pci_remove+0x15/0x20 [i915]
 pci_device_remove+0x36/0xb0
 device_release_driver_internal+0x15f/0x220
 driver_detach+0x3a/0x80
 bus_remove_driver+0x58/0xd0
 pci_unregister_driver+0x29/0x90
 SyS_delete_module+0x150/0x1e0
 entry_SYSCALL_64_fastpath+0x23/0x9a
RIP: 0033:0x7ff43b51b5c7
RSP: 002b:00007ffe6825a758 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007ff43b51b5c7
RDX: 000000000000000a RSI: 0000000000000800 RDI: 000055df3ef35808
RBP: 0000000000000000 R08: 00007ffe682596d1 R09: 0000000000000000
R10: 00007ff43b594880 R11: 0000000000000206 R12: 000055df3ef357a0
R13: 00007ffe68259740 R14: 000055df3ef35260 R15: 000055df3ef357a0
Code: 00 00 02 74 03 31 c0 c3 53 48 89 fb 48 83 ec 10 e8 52 0f
f8 ff 48 b8 01 05 00 00 02 00 00 00 48 89 44 24 04 48 8b 83 00 12 00 00 <f6> 80
f9 00 00 00 01 0f 84 a7 00 00 00 f6 80 98 00 00 00 01 0f
RIP: intel_guc_suspend+0x34/0x140 [i915] RSP: ffffc90000483df8
CR2: 00000000000000f9
---[ end trace 23a192a61d937a3e ]---

Fixes: b8e5eb960b28 ("drm/i915/guc: Allocate separate shared data object for GuC communication")
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213221352.7173-1-michal.winiarski@intel.com

drm/i915: Unwind i915_gem_init() failure

Since Michal introduced new user controllable errors other than -EIO
during i915_gem_init(), we need to actually unwind on the error path as
we have to abort the module load (and we expect to do so cleanly!).

As we now teardown key state and then mark the driver as wedged (on
EIO), we have to be careful to not allow ourselves to resume and
unwedge, thus attempting to use the uninitialised driver.

v2: Try not to free driver state for the suppressed EIO
v3: Use load-fault-injection to test both error/recovery paths.

References: 8620eb1dbbf2 ("drm/i915/uc: Don't use -EIO to report missing firmware")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213134347.4608-1-chris@chris-wilson.co.uk

drm/i915: Ratelimit request allocation under oom

If we fail to allocate a request, we can reap the outstanding requests
and push them to the request's slab's freelist before trying again. This
forces us to ratelimit malicious clients that tie up all of the system
resources in requests, instead of causing a system-wide oom.

Testcase: igt/gem_shrink/execbuf1
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171212180652.22061-3-chris@chris-wilson.co.uk

drm/i915: Allow fence allocations to fail

If a fence allocation fails in a blocking context, we will sleep on the
fence as a last resort. We can therefore allow ourselves to fail and
sleep on the fence instead of triggering a system-wide oom. This allows
us to throttle malicious clients that are consuming lots of system
resources by capping the amount of memory used by fences.

Testcase: igt/gem_shrink/execbufX
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171212180652.22061-2-chris@chris-wilson.co.uk

drm/i915: Mark up potential allocation paths within i915_sw_fence as might_sleep

As kmalloc is allowed to block (if given the right flags), mark up the
two i915_sw_fence routines that may call kmalloc as potential sleeping
routines.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171212180652.22061-1-chris@chris-wilson.co.uk

drm/i915: Don't check #active_requests from i915_gem_wait_for_idle()

i915_gem_wait_for_idle() is called from inside the shrinker, to ensure
that we drain the last resources from the GPU in dire circumstances (OOM).
As we may allocate whilst building a request, it is then possible to hit
the shrinker with a request under construction, and so we must account
for the incomplete request whilst waiting. In particular, we
preincrement (in reserve_engine) the i915->gt.active_requests counter
and mark the GPU as busy, therefore we can not use that counter for
shortcircuiting the wait-for-idle.

[  950.859024] GEM_BUG_ON(i915->gt.active_requests)
[  950.859041] WARNING: CPU: 2 PID: 2178 at drivers/gpu/drm/i915/i915_gem.c:3615 i915_gem_wait_for_idle.part.56+0x166/0x4e0
[  950.859041] Modules linked in: ccm tun fuse nf_conntrack_netbios_ns nf_conntrack_broadcast ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 nf_conntrack_ipv6 nf_defrag_ipv6 nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack libcrc32c ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_mangle iptable_security iptable_raw arc4 iwldvm mac80211 snd_hda_codec_hdmi snd_hda_codec_idt snd_hda_codec_generic snd_hda_intel snd_hda_codec btusb snd_hda_core btrtl btbcm iwlwifi snd_hwdep btintel bluetooth snd_seq snd_seq_device snd_pcm ecdh_generic x86_pkg_temp_thermal tpm_infineon coretemp tpm_tis crc32_pclmul wmi_bmof crc32c_intel iTCO_wdt hp_wmi snd_timer iTCO_vendor_support sparse_keymap tpm_tis_core mei_me cfg80211
[  950.859082]  snd joydev tpm mei rfkill pcspkr wmi soundcore lpc_ich hp_accel lis3lv02d input_polldev binfmt_misc e1000e ptp serio_raw pps_core
[  950.859094] CPU: 2 PID: 2178 Comm: gem_exec_nop Tainted: G     U           4.15.0-rc2+ #900
[  950.859102] Hardware name: Hewlett-Packard HP ProBook 6360b/1620, BIOS 68SCF Ver. B.42 12/29/2010
[  950.859107] task: c5119cb4 task.stack: f3ccb8d8
[  950.859112] EIP: i915_gem_wait_for_idle.part.56+0x166/0x4e0
[  950.859113] EFLAGS: 00010296 CPU: 2
[  950.859114] EAX: 00000024 EBX: f36c1888 ECX: f777a044 EDX: 00000007
[  950.859115] ESI: f36c1888 EDI: edd53958 EBP: edd53970 ESP: edd53938
[  950.859116]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[  950.859117] CR0: 80050033 CR2: b7f39000 CR3: 2f2b3000 CR4: 000406d0
[  950.859118] Call Trace:
[  950.859125]  ? drm_printk+0x70/0x70
[  950.859129]  i915_gem_wait_for_idle+0x18/0x30
[  950.859133]  i915_gem_shrink+0x360/0x410
[  950.859138]  ? vmpressure+0xa8/0xf0
[  950.859142]  ? ktime_get+0x4a/0x100
[  950.859147]  i915_gem_shrink_all+0x21/0x40
[  950.859151]  i915_gem_shrinker_oom+0x23/0x130
[  950.859156]  notifier_call_chain+0x4e/0x70
[  950.859160]  __blocking_notifier_call_chain+0x2f/0x60
[  950.859164]  blocking_notifier_call_chain+0x11/0x20
[  950.859169]  out_of_memory+0x207/0x280
[  950.859174]  __alloc_pages_nodemask+0xd47/0xe60
[  950.859179]  new_slab+0x32d/0x450
[  950.859183]  ___slab_alloc.constprop.81+0x358/0x4e0
[  950.859189]  ? i915_sw_fence_await_dma_fence+0x53/0x160
[  950.859193]  ? __slab_free+0x1fe/0x310
[  950.859197]  ? native_sched_clock+0x1e/0xc0
[  950.859201]  ? i915_gem_request_alloc+0xcf/0x510
[  950.859205]  ? sched_clock+0x9/0x10
[  950.859209]  __slab_alloc.constprop.80+0x29/0x40
[  950.859212]  ? __slab_alloc.constprop.80+0x29/0x40
[  950.859216]  kmem_cache_alloc_trace+0x160/0x1a0
[  950.859220]  ? i915_sw_fence_await_dma_fence+0x53/0x160
[  950.859224]  i915_sw_fence_await_dma_fence+0x53/0x160
[  950.859229]  i915_gem_request_await_dma_fence+0x1eb/0x390
[  950.859233]  i915_gem_request_await_object+0xee/0x230
[  950.859239]  i915_gem_do_execbuffer+0xc16/0x1200
[  950.859246]  ? irqtime_account_irq+0x3e/0xc0
[  950.859251]  ? irq_exit+0x4f/0xb0
[  950.859257]  ? smp_apic_timer_interrupt+0x5f/0x110
[  950.859261]  ? apic_timer_interrupt+0x35/0x3c
[  950.859266]  i915_gem_execbuffer2_ioctl+0x212/0x440
[  950.859270]  ? apic_timer_interrupt+0x35/0x3c
[  950.859274]  ? i915_gem_do_execbuffer+0x1200/0x1200
[  950.859279]  ? insn_get_seg_base+0x1b/0x50
[  950.859283]  ? i915_gem_do_execbuffer+0x1200/0x1200
[  950.859287]  drm_ioctl_kernel+0x51/0xa0
[  950.859291]  drm_ioctl+0x2a3/0x350
[  950.859294]  ? i915_gem_do_execbuffer+0x1200/0x1200
[  950.859300]  ? sched_clock+0x9/0x10
[  950.859303]  ? drm_getunique+0x70/0x70
[  950.859308]  do_vfs_ioctl+0x7d/0x640
[  950.859311]  ? native_sched_clock+0x1e/0xc0
[  950.859315]  ? sched_clock+0x9/0x10
[  950.859319]  ? sched_clock_cpu+0x13/0x120
[  950.859323]  SyS_ioctl+0x4e/0x80
[  950.859326]  do_fast_syscall_32+0x75/0x250
[  950.859331]  ? irq_exit+0x4f/0xb0
[  950.859334]  entry_SYSENTER_32+0x47/0x71
[  950.859338] EIP: 0xb7f81d11
[  950.859339] EFLAGS: 00000296 CPU: 2
[  950.859340] EAX: ffffffda EBX: 00000003 ECX: 40406469 EDX: bfde4c20
[  950.859340] ESI: 00000003 EDI: 40406469 EBP: 00000003 ESP: bfde4b38
[  950.859341]  DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 007b
[  950.859343] Code: e8 30 60 01 00 83 c4 10 83 c3 04 39 f3 75 e0 8b 45 d8 8b 80 14 37 00 00 85 c0 74 13 68 dd 33 e4 c0 68 49 6f e3 c0 e8 4a 55 be ff <0f> ff 5e 5f b8 fe ff ff 3f bb 0a 00 00 00 e8 b7 14 c4 ff 8b 15

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171212132148.8124-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915/fence: Use rcu to defer freeing of irq_work

It is illegal to perform an immediate free of the struct irq_work from
inside the irq_work callback (as irq_work_run_list modifies work->flags
after execution of the work->func()). As we use the irq_work to
coordinate the freeing of the callback from two different softirq paths,
we need to defer the kfree from inside our irq_work callback, for which
we can use kfree_rcu.

Fixes: 81c0ed21aa91 ("drm/i915/fence: Avoid del_timer_sync() from inside a timer")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213094802.28243-1-chris@chris-wilson.co.uk

drm/i915: Dump the engine state before declaring wedged from wait_for_engines()

If wait_for_engines() fails and we resort to declaring the HW wedged,
dump the engine state for debugging.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171211194135.27095-2-chris@chris-wilson.co.uk

drm/i915: Bump timeout for wait_for_engines()

Extract the timeout we use in i915_gem_idle_work_handler() and reuse it
for wait_for_engines() in i915_gem_wait_for_idle(). It too has the same
problem in sometimes having to wait for an extended period before the HW
settles, so make use of the same timeout.

References: 5427f207852d ("drm/i915: Bump wait-times for the final CS interrupt before parking")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171211194135.27095-1-chris@chris-wilson.co.uk

drm/i915: Downgrade misleading "Memory usable" message

It never meant what it said, as it was always the total size of the
Global GTT and not a limit upon memory usage. Originally it served as a
quick guide to the largest batch that could be submitted by userspace,
an approximation to its maximum RSS, but was phrased badly. Today with
the 48b ppgtt, it is even more meaningless. Replace with a more specific
debug message; those wanting to know how much "video ram" they have
should consult the userspace libraries for the relevant approximation.

v2: Rebase

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171212113532.22574-1-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Print an error message for a reset failure on gen2

Since on gen2, we do not universally have a GPU reset implementation, we
fail i915_reset() at intel_has_gpu_reset(). However, this is also
intentionally disabled for CI testing and so it only has a debug
message. Promote that debug message to a user-facing error message that
should explain why their machine became unusable following the GPU hang.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171211204040.22858-1-chris@chris-wilson.co.uk

docs: fix, intel_guc_loader.c has been moved to intel_guc_fw.c

With commit d9e2e0143c the 'GuC-specific firmware loader' doc
section was removed from intel_guc_loader.c without a
replacement.  So lets remove it from the Kernel-doc::

  .. kernel-doc:: drivers/gpu/drm/i915/intel_guc_loader.c
     :doc: GuC-specific firmware loader

With commit e8668bbcb0 intel_guc_loader.c was renamed to to
intel_guc_fw.c and to name just one, intel_guc_init_hw() was
renamed to intel_guc_fw_upload(). Since we get errors in the
Sphinx build like:

- Error: Cannot open file ./drivers/gpu/drm/i915/intel_guc_loader.c

Change the kernel-doc directive from intel_guc_loader.c to
intel_guc_fw.c

Signed-off-by: Markus Heiser <markus.heiser@darmarit.de>
[danvet: Rebase onto the partial fix 006c23327f8d
("documentation/gpu/i915: fix docs build error after file rename")]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1513078717-12373-1-git-send-email-markus.heiser@darmarit.de

drm/i915: prefer resource_size_t for everything stolen

Keeps things consistent now that we make use of struct resource. This
should keep us covered in case we ever get huge amounts of stolen
memory.

v2: bunch of missing conversions (Chris)

Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171211151822.20953-10-matthew.auld@intel.com

drm/i915: give stolen_usable_size a more suitable home

Kick it out of i915_ggtt and keep it grouped with dsm and dsm_reserved,
where it makes the most sense.

Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171211151822.20953-9-matthew.auld@intel.com

drm/i915: make mappable struct resource centric

Now that we are using struct resource to track the stolen region, it is
more convenient if we track the mappable region in a resource as well.

v2: prefer iomap and gmadr naming scheme
    prefer DEFINE_RES_MEM

Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171211151822.20953-8-matthew.auld@intel.com

drm/i915: make reserved struct resource centric

Now that we are using struct resource to track the stolen region, it is
more convenient if we track the reserved portion of that region in a
resource as well.

v2: s/<= end + 1/< end/ (Chris)
v3: prefer DEFINE_RES_MEM

Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171211151822.20953-7-matthew.auld@intel.com

drm/i915: make dsm struct resource centric

Now that we are using struct resource to track the stolen region, it is
more convenient if we track dsm in a resource as well.

v2: check range_overflow when writing to 32b registers (Chris)
    pepper in some comments (Chris)
v3: refit i915_stolen_to_dma()
v4: kill ggtt->stolen_size
v5: some more polish

Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171211151822.20953-6-matthew.auld@intel.com

drm/i915: nuke the duplicated stolen discovery

We duplicate the stolen discovery code in early-quirks and in i915,
however now that the stolen region is exported as a resource from
early-quirks we can nuke the duplication.

v2: check overflows_type

Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171211151822.20953-5-matthew.auld@intel.com

x86/early-quirks: replace the magical increment start values

Replace the magical +2, +9 etc. with +MB, which is far easier to read.

Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: x86@kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171211151822.20953-4-matthew.auld@intel.com