Troy Kisky [Mon, 11 Feb 2008 21:44:07 +0000 (14:44 -0700)]
davinci: interrupts: get_irqnr_and_base: save an instruction
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Chaithrika U S [Mon, 19 Jan 2009 08:43:05 +0000 (14:13 +0530)]
davinci: use 32-bit accesses for low-level debug macros
This patch defines debug macros for low-level debugging for Davinci
based platforms
Tested on :
- DM644x DaVinci EVM
- DM646X DaVinciHD EVM
- DM355 EVM
This patch attempts to solve the low-level debug issue in DM646x. The
UART on DM646x SoC allows only 32-bit access. The existing
debug-macro.S uses the macros from debug-8250.S file. This led to
garbage serial out in the case of DM646x.
The inclusion of debug-8250.S does not allow for run time fix for this
issue. There are compile time errors due to multiple definitions of
the macros. Also when building a single image for multiple DaVinci
Platforms, the ifdefs cannot be relied upon.
The solution below does not include the debug-8250.S file and defines
the necessary macros. This solution was arrived at after observing
that word access does not affect the low-level debug messages on
DM644x/DM355.
The other approach to this issue is to use the UART module information
available in the peripheral registers to decide the access
mechanism. But this will have to be done for every access of UART
specifically for DM646x. Also this calls for a modification of the
debug-8250.S file.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Mon, 11 May 2009 18:04:53 +0000 (11:04 -0700)]
davinci: fixups for banked GPIO interrupt handling
This patch seems to get me much more reliable performance using the
GPIO banked interrupts on dm355 for the dm9000 driver.
Changes include:
- init GPIO handling along with normal GPIO init
- mask the level-sensitive bank IRQ during handling
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
David Brownell [Mon, 4 May 2009 20:14:27 +0000 (13:14 -0700)]
davinci: gpio irq enable tweaks
Fix two IRQ triggering bugs affecting GPIO IRQs:
- Make sure enabling with IRQ_TYPE_NONE ("default, unspecified")
isn't a NOP ... default to both edges, at least one must work.
- As noted by Kevin Hilman, setting the irq trigger type for a
banked gpio interrupt shouldn't enable irqs that are disabled.
Since GPIO IRQs haven't been used much yet, it's not clear these
bugs could have affected anything. The few current users don't
seem to have been obviously suffering from these issues.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Linus Torvalds [Sat, 23 May 2009 21:47:00 +0000 (14:47 -0700)]
Linux 2.6.30-rc7
Linus Torvalds [Sat, 23 May 2009 20:44:00 +0000 (13:44 -0700)]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] mpt2sas: fix driver version inconsistency
[SCSI] 3w-xxxx: scsi_dma_unmap fix
[SCSI] 3w-9xxx: scsi_dma_unmap fix
[SCSI] ses: fix problems caused by empty SES provided name
[SCSI] fc-transport: Close state transition-window during rport deletion.
[SCSI] initialize max_target_blocked in scsi_alloc_target
[SCSI] fnic: Add new Cisco PCI-Express FCoE HBA
Linus Torvalds [Sat, 23 May 2009 20:42:53 +0000 (13:42 -0700)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Avoid open on possible directories since Samba now rejects them
Steve French [Sat, 23 May 2009 18:57:25 +0000 (18:57 +0000)]
[CIFS] Avoid open on possible directories since Samba now rejects them
Small change (mostly formatting) to limit lookup based open calls to
file create only.
After discussion yesteday on samba-technical about the posix lookup
regression, and looking at a problem with cifs posix open to one
particular Samba version, Jeff and JRA realized that Samba server's
behavior changed in this area (posix open behavior on files vs.
directories). To make this behavior consistent, JRA just made a
fix to Samba server to alter how it handles open of directories (now
returning the equivalent of EISDIR instead of success). Since we don't
know at lookup time whether the inode is a directory or file (and
thus whether posix open will succeed with most current Samba server),
this change avoids the posix open code on lookup open (just issues
posix open on creates). This gets the semantic benefits we want
(atomicity, posix byte range locks, improved write semantics on newly
created files) and file create still is fast, and we avoid the problem
that Jeff noticed yesterday with "openat" (and some open directory
calls) of non-cached directories to one version of Samba server, and
will work with future Samba versions (which include the fix jra just
pushed into Samba server). I confirmed this approach with jra
yesterday and with Shirish today.
Posix open is only called (at lookup time) for file create now.
For opens (rather than creates), because we do not know if it
is a file or directory yet, and current Samba no longer allows
us to do posix open on dirs, we could end up wasting an open call
on what turns out to be a dir. For file opens, we wait to call posix
open till cifs_open. It could be added here (lookup) in the future
but the performance tradeoff of the extra network request when EISDIR
or EACCES is returned would have to be weighed against the 50%
reduction in network traffic in the other paths.
Reviewed-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Tested-by: Jeff Layton <jlayton@redhat.com>
CC: Jeremy Allison <jra@samba.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Breno Leitao [Sat, 23 May 2009 00:30:39 +0000 (21:30 -0300)]
icom: fix rmmod crash
Actually the icom driver is crashing when is being removed because
the driver is kfreeing the adapter structure before calling
pci_release_regions(), which result in the following error:
Unable to handle kernel paging request for data at address 0x6b6b6b6b6b6b6d33
Faulting instruction address: 0xc000000000246b80
Oops: Kernel access of bad area, sig: 11 [#1]
....
[
c000000012d436a0] [
c0000000001002d0] .kfree+0x120/0x34c (unreliable)
[
c000000012d43730] [
c000000000246d60] .pci_release_selected_regions+0x3c/0x68
[
c000000012d437c0] [
d000000002d54700] .icom_kref_release+0xf4/0x118 [icom]
[
c000000012d43850] [
c000000000232e50] .kref_put+0x74/0x94
[
c000000012d438d0] [
d000000002d56c58] .icom_remove+0x40/0xa4 [icom]
[
c000000012d43960] [
c000000000249e48] .pci_device_remove+0x50/0x90
[
c000000012d439e0] [
c0000000002d68d8] .__device_release_driver+0x94/0xd4
[
c000000012d43a70] [
c0000000002d7104] .driver_detach+0xf8/0x12c
[
c000000012d43b00] [
c0000000002d549c] .bus_remove_driver+0xbc/0x11c
[
c000000012d43b90] [
c0000000002d71dc] .driver_unregister+0x60/0x80
[
c000000012d43c20] [
c00000000024a07c] .pci_unregister_driver+0x44/0xe8
[
c000000012d43cb0] [
d000000002d56bf4] .icom_exit+0x1c/0x40 [icom]
[
c000000012d43d30] [
c000000000095fa8] .SyS_delete_module+0x214/0x2a8
[
c000000012d43e30] [
c00000000000852c] syscall_exit+0x0/0x40
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: stable@kernel.org
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 22 May 2009 20:38:52 +0000 (13:38 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: Kill truncate warning by shortening Sigmatel-specific AC97 control name
ALSA: hda - fix audio on HP TX25xx series notebooks
ALSA: pcsp - fix printk format warning again
Takashi Iwai [Fri, 22 May 2009 17:29:08 +0000 (19:29 +0200)]
Merge branch 'fix/misc' into for-linus
* fix/misc:
ALSA: Kill truncate warning by shortening Sigmatel-specific AC97 control name
ALSA: pcsp - fix printk format warning again
Andreas Mohr [Fri, 22 May 2009 15:48:58 +0000 (17:48 +0200)]
ALSA: Kill truncate warning by shortening Sigmatel-specific AC97 control name
ALSA sound/core/control.c:232: Control name 'Sigmatel Surround Phase
Inversion Playback Switch' truncated to 'Sigmatel Surround Phase
Inversion Playback ' bootup message by omitting weird Sigmatel prefix
in this case; also fix up the related ca0106 mixer control removal
part by using identical naming there.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Fri, 22 May 2009 15:41:13 +0000 (08:41 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ryusuke/nilfs2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
nilfs2: fix memory leak in nilfs_ioctl_clean_segments
Linus Torvalds [Fri, 22 May 2009 15:22:39 +0000 (08:22 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/bart/ide-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
via82cxxx: Add VIA VX855 PCI Device ID
ide: report timeouts in ide_busy_sleep()
ide: improve failed opcode reporting
ide: fix printk() levels in ide_dump_ata[pi]_error()
ide: fix OOPS during ide-cd error recovery
ide: fix 40-wire cable detection for TSST SH-S202* ATAPI devices (v2)
Linus Torvalds [Fri, 22 May 2009 14:38:28 +0000 (07:38 -0700)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] fix posix open regression
Linus Torvalds [Fri, 22 May 2009 14:37:42 +0000 (07:37 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: IP32: Remove unnecessary if not even harmful volatile keywords.
MIPS: IP32: Fix build error due to uninitialized variable.
MIPS: Fix sparse warning in incompatiable argument type of clear_user.
Linus Torvalds [Fri, 22 May 2009 14:33:49 +0000 (07:33 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/maple: Add a quirk to disable MSI for IPR on Bimini
Linus Torvalds [Fri, 22 May 2009 14:33:38 +0000 (07:33 -0700)]
Merge branch 'sh/for-2.6.30' of git://git./linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.30' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
video: stop sh_mobile_lcdcfb only if started
sh: ap325 camera without i2c driver fix
Corey Minyard [Wed, 20 May 2009 18:36:17 +0000 (13:36 -0500)]
ipmi: fix ipmi_si modprobe hang
Instead of queuing IPMB messages before channel initialization, just
throw them away. Nobody will be listening for them at this point,
anyway, and they will clog up the queue and nothing will be delivered
if we queue them.
Also set the current channel to the number of channels, as this value
is used to tell if the channel information has been initialized.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Ferenc Wagner <wferi@niif.hu>
Cc: Dan Frazier <dannf@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Harald Welte [Fri, 22 May 2009 14:23:39 +0000 (16:23 +0200)]
via82cxxx: Add VIA VX855 PCI Device ID
This patch adds the PCI Device ID 0xc409 to the PCI ID table of via82cxxx.c,
as well as the 0x8409 south bridge ID.
This is required to make the IDE driver work on the VX855/VX875 integrated
chipset.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Bruce Chang <BruceChang@via.com.tw>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 14:23:38 +0000 (16:23 +0200)]
ide: report timeouts in ide_busy_sleep()
* change 'hwif' argument to 'drive'
* report an error on timeout
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 14:23:38 +0000 (16:23 +0200)]
ide: improve failed opcode reporting
Nowadays we (almost) always store the currently executing command
in hwif->cmd so we can use it for the failed opcode reporting.
Cc: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 14:23:37 +0000 (16:23 +0200)]
ide: fix printk() levels in ide_dump_ata[pi]_error()
Fixes "<3>" in error messages like this one:
hdc: cdrom_decode_status: error=0x40 <3>{ LastFailedSense=0x04 }
Reported-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 14:23:37 +0000 (16:23 +0200)]
ide: fix OOPS during ide-cd error recovery
On Tuesday 19 May 2009 20:29:28 Martin Lottermoser wrote:
> hdc: cdrom_decode_status: error=0x40 <3>{ LastFailedSense=0x04 }
> ide: failed opcode was: unknown
> hdc: DMA disabled
> ------------[ cut here ]------------
> kernel BUG at drivers/ide/ide-io.c:872!
It is possible for ide-cd to ignore ide_error()'s return value under
some circumstances. Workaround it in ide_intr() and ide_timer_expiry()
by checking if there is a device/port reset pending currently.
Fixes bug #13345:
http://bugzilla.kernel.org/show_bug.cgi?id=13345
Reported-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Reported-and-tested-by: Modestas Vainius <modestas@vainius.eu>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 14:23:36 +0000 (16:23 +0200)]
ide: fix 40-wire cable detection for TSST SH-S202* ATAPI devices (v2)
Since 2.6.26 we support UDMA66 on ATAPI devices requiring IVB quirk:
commit
8588a2b732928b343233af9b1855705b8286bed4
("ide: add SH-S202J to ivb_list[]")
We also later added support for more such devices in:
commit
e97564f362a93f8c248246c19828895950341252
("ide: More TSST drives with broken cable detection")
and in:
commit
3ced5c49bd2d1f2c7f769e3a54385883de63a652
("ide: add TSSTcorp CDDVDW SH-S202H to ivb_list[]")
It turns out that such devices lack cable detection altogether
(which in turn results in incorrect detection of 40-wire cables
by our current cable detection strategy) so always handle them
by trusting host-side cable detection only.
v2:
Model detection fixup from Martin.
Reported-and-tested-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Ralf Baechle [Fri, 22 May 2009 09:58:43 +0000 (10:58 +0100)]
MIPS: IP32: Remove unnecessary if not even harmful volatile keywords.
They are unneeded and as the issue fixed in lmo commit
63f7ec59053e3f850ab67a9938e631bcba64c6ce shows even harmful.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Fri, 22 May 2009 09:48:17 +0000 (10:48 +0100)]
MIPS: IP32: Fix build error due to uninitialized variable.
CC arch/mips/sgi-ip32/ip32-reset.o
cc1: warnings being treated as errors
arch/mips/sgi-ip32/ip32-reset.c: In function 'debounce':
arch/mips/sgi-ip32/ip32-reset.c:97: error: 'reg_a' is used uninitialized in this function
The issues is old but due to the volatile keyword gcc older than 4.4 did
not warn about this obvious bug.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Wu Zhangjin [Wed, 20 May 2009 21:50:01 +0000 (05:50 +0800)]
MIPS: Fix sparse warning in incompatiable argument type of clear_user.
The type of the second argument of access_ok should be (void __user *).
The unnecessary conversion of the clear_user address argument was causing
sparse to emit warnings on the __chk_user_ptr check.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ryusuke Konishi [Fri, 22 May 2009 11:36:21 +0000 (20:36 +0900)]
nilfs2: fix memory leak in nilfs_ioctl_clean_segments
This fixes a new memory leak problem in garbage collection. The
problem was brought by the bugfix patch ("nilfs2: fix lock order
reversal in nilfs_clean_segments ioctl").
Thanks to Kentaro Suzuki for finding this problem.
Reported-by: Kentaro Suzuki <k_suzuki@ms.sylc.co.jp>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Takashi Iwai [Fri, 22 May 2009 06:23:39 +0000 (08:23 +0200)]
Merge branch 'fix/hda' into for-linus
* fix/hda:
ALSA: hda - fix audio on HP TX25xx series notebooks
Adam Williamson [Thu, 21 May 2009 22:32:59 +0000 (18:32 -0400)]
ALSA: hda - fix audio on HP TX25xx series notebooks
Fixes https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4121
Taken from https://bugzilla.redhat.com/show_bug.cgi?id=498060
Signed-off-by: Adam Williamson <awilliam@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Michael Ellerman [Thu, 21 May 2009 19:10:23 +0000 (19:10 +0000)]
powerpc/maple: Add a quirk to disable MSI for IPR on Bimini
Something in the HW or FW setup is busted and MSIs aren't working with
IPR on Bimini, so until we figure out exaxtly what's up, we quirk them
out
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Magnus Damm [Wed, 20 May 2009 14:34:43 +0000 (14:34 +0000)]
video: stop sh_mobile_lcdcfb only if started
This patch fixes the LCDC driver to avoid calling the
function sh_mobile_lcdc_start_stop(priv, 0) unless the
same function has been called before to start the LCDC
hardware.
Triggered when sh_mobile_lcdcfb.c failed to probe() due to
missing MSTP clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 20 May 2009 14:30:06 +0000 (14:30 +0000)]
sh: ap325 camera without i2c driver fix
This patch fixes the ap325rxa ncm03j camera code to handle
the case where no i2c driver is present. Without this fix
i2c_transfer() may be passed NULL as adapter which results
in a crash.
Triggered when i2c-sh_mobile.c failed to probe() due to
missing MSTP clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Steve French [Thu, 21 May 2009 22:21:53 +0000 (22:21 +0000)]
[CIFS] fix posix open regression
Posix open code was not properly adding the file to the
list of open files. Fix allocating cifsFileInfo
more than once, and adding twice to flist and tlist.
Also fix mode setting to be done in one place in these
paths.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Reviewed-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Tested-by: Jeff Layton <jlayton@redhat.com>
Tested-by: Luca Tettamanti <kronos.it@gmail.com>
Hugh Dickins [Thu, 21 May 2009 19:33:58 +0000 (20:33 +0100)]
hugh: update email address
My old address will shut down in a few days time: remove it from the tree,
and add a tmpfs (shmem filesystem) maintainer entry with the new address.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 20 May 2009 23:44:37 +0000 (16:44 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI PM: Fix initialization and kexec breakage for some devices
Linus Torvalds [Wed, 20 May 2009 23:40:24 +0000 (16:40 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/drm-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-2.6:
drm: Copy back ioctl data to userspace regardless of return code.
drm: Round size of SHM maps to PAGE_SIZE
Linus Torvalds [Wed, 20 May 2009 23:32:19 +0000 (16:32 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: 64-bit: Fix system lockup.
MIPS: IP28: Change to build with -mr10k-cache-barrier=store
MIPS: IP22: Fix hang in power button interrupt handler
MIPS: IP32: Fix hang on shutdown in power button interrupt handler.
Linus Torvalds [Wed, 20 May 2009 23:30:36 +0000 (16:30 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm: (25 commits)
[ARM] 5519/1: amba probe: pass "struct amba_id *" instead of void *
[ARM] 5517/1: integrator: don't put clock lookups in __initdata
[ARM] 5518/1: versatile: don't put clock lookups in __initdata
[ARM] mach-l7200: fix spelling of SYS_CLOCK_OFF
[ARM] Double check memmap is actually valid with a memmap has unexpected holes V2
[ARM] realview: fix broadcast tick support
[ARM] realview: remove useless smp_cross_call_done()
[ARM] smp: fix cpumask usage in ARM SMP code
[ARM] 5513/1: Eurotech VIPER SBC: fix compilation error
[ARM] 5509/1: ep93xx: clkdev enable UARTS
ARM: OMAP2/3: Change omapfb to use clkdev for dispc and rfbi, v2
ARM: OMAP3: Fix HW SAVEANDRESTORE shift define
ARM: OMAP3: Fix number of GPIO lines for 34xx
[ARM] S3C: Do not set clk->owner field if unset
[ARM] S3C2410: mach-bast.c registering i2c data too early
[ARM] S3C24XX: Fix unused code warning in arch/arm/plat-s3c24xx/dma.c
[ARM] S3C64XX: fix GPIO debug
[ARM] S3C64XX: GPIO include cleanup
[ARM] nwfpe: fix 'floatx80_is_nan' sparse warning
[ARM] nwfpe: Add decleration for ExtendedCPDO
...
Alessandro Rubini [Wed, 20 May 2009 21:39:08 +0000 (22:39 +0100)]
[ARM] 5519/1: amba probe: pass "struct amba_id *" instead of void *
The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.
Change suggested by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Michel Dänzer [Wed, 20 May 2009 11:32:00 +0000 (13:32 +0200)]
drm: Copy back ioctl data to userspace regardless of return code.
Fixes a regression from commit
9d5b3ffc42f7820e8ee07705496955e4c2c38dd9
('drm: fixup some of the ioctl function exit paths'): The vblank ioctl
needs to update the userspace parameters when interrupted by a signal,
which was prevented by the return code check. This could cause the X
server to hang in drmWaitVBlank().
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Greg Ungerer [Wed, 20 May 2009 06:12:32 +0000 (16:12 +1000)]
MIPS: 64-bit: Fix system lockup.
The address range size calculation inside local_flush_tlb_kernel_range()
is being truncated by a too small size variable holder on 64-bit systems.
The truncated size can result in an erroneous tlbsize check that means we
sit spinning inside a loop trying to flush a hige number of TLB entries.
This is for all intents and purposes a system hang. Fix by using an
appropriately sized valiable to hold the size.
[Ralf: Greg's original patch submission identified the issue and fixed one
instance in tlb-r4k.c but there there were several more. For consistency
I also modified tlb-r3k.c even though that file is only used on 32-bit.]
Signed-off-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
peter fuerst [Sun, 17 May 2009 21:49:45 +0000 (23:49 +0200)]
MIPS: IP28: Change to build with -mr10k-cache-barrier=store
Richard Sandiford's new code for inserting the cache-barriers, for GCC
4.3 and above and already incorporated in the current GCC-release, uses
a slightly different option-syntax.
Signed-off-by: peter fuerst <post@pfrst.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Sat, 16 May 2009 11:23:45 +0000 (12:23 +0100)]
MIPS: IP22: Fix hang in power button interrupt handler
The hang was caused by the use of disable_irq() from the interrupt handler
itself. Fixed by the use of disable_irq_nosync(). The issue was
triggered by:
commit
3aa551c9b4c40018f0e261a178e3d25478dc04a9
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Mon Mar 23 18:28:15 2009 +0100
genirq: add threaded interrupt handler support
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Andrew Randrianasulu [Thu, 14 May 2009 18:29:27 +0000 (11:29 -0700)]
MIPS: IP32: Fix hang on shutdown in power button interrupt handler.
The hang was caused by the use of disable_irq() from the interrupt handler
itself. Fixed by the use of disable_irq_nosync(). The issue was
triggered by:
commit
3aa551c9b4c40018f0e261a178e3d25478dc04a9
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Mon Mar 23 18:28:15 2009 +0100
genirq: add threaded interrupt handler support
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds [Wed, 20 May 2009 15:56:10 +0000 (08:56 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cdrom: beyond ARRAY_SIZE of viocd_diskinfo
xen/blkfront: fix warning when deleting gendisk on unplug/shutdown
xen/blkfront: allow xenbus state transition to Closing->Closed when not Connected
Linus Torvalds [Wed, 20 May 2009 15:36:53 +0000 (08:36 -0700)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: fix pointer initialization and checks in cifs_follow_symlink (try #4)
Takashi Iwai [Wed, 20 May 2009 15:05:52 +0000 (17:05 +0200)]
ALSA: pcsp - fix printk format warning again
The commit
5a641bcd6398841cc4606b0a732d41a09256fd94 changed the
printk format to '%lu', but the value passed seems to be dependent
on the architecture. On x86-64, I got a new warning now because an
int value is passed actaully.
As a workaround, just cast the value always to unsigned long.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Roel Kluin [Wed, 20 May 2009 06:42:06 +0000 (08:42 +0200)]
cdrom: beyond ARRAY_SIZE of viocd_diskinfo
Do not go beyond ARRAY_SIZE of viocd_diskinfo
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Linus Torvalds [Wed, 20 May 2009 01:44:09 +0000 (18:44 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sameo/mfd-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: pcf50633: fix unsafe disable_irq()
mfd: Keep a cache of WM8350 volatile values
Linus Torvalds [Wed, 20 May 2009 01:43:50 +0000 (18:43 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ipv4: make default for INET_LRO consistent with help text
net: fix skb_seq_read returning wrong offset/length for page frag data
pkt_sched: gen_estimator: use 64 bit intermediate counters for bps
be2net: add two new pci device ids to pci device table
sch_teql: should not dereference skb after ndo_start_xmit()
tcp: fix MSG_PEEK race check
Doc: fixed descriptions on /proc/sys/net/core/* and /proc/sys/net/unix/*
Neterion: *FIFO1_DMA_ERR set twice, should 2nd be *FIFO2_DMA_ERR?
mv643xx_eth: fix PPC DMA breakage
bonding: fix link down handling in 802.3ad mode
bridge: fix initial packet flood if !STP
bridge: relay bridge multicast pkgs if !STP
NET: Meth: Fix unsafe mix of irq and non-irq spinlocks.
mlx4_en: Fix not deleted napi structures
ipconfig: handle case of delayed DHCP server
netpoll: don't dereference NULL dev from np
wimax/i2400m: fix device crash: fix optimization in _roq_queue_update_ws
Linus Torvalds [Wed, 20 May 2009 01:43:21 +0000 (18:43 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
TPM: get_event_name stack corruption
Linus Torvalds [Wed, 20 May 2009 01:42:45 +0000 (18:42 -0700)]
Merge branch 'core/urgent' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: setup writeable mapping for futex ops which modify user space data
Benjamin Herrenschmidt [Mon, 18 May 2009 01:56:16 +0000 (11:56 +1000)]
drm: Round size of SHM maps to PAGE_SIZE
Currently, userspace can fail to obtain the SAREA mapping (among other
reasons) if it passes SAREA_MAX to drmAddMap without aligning it to the
page size. This breaks for example on PowerPC with 64K pages and radeon
despite the kernel radeon actually doing the right rouding in the first
place.
The way SAREA_MAX is defined with a bunch of ifdef's and duplicated
between libdrm and the X server is gross, ultimately it should be
retrieved by userspace from the kernel, but in the meantime, we have
plenty of existing userspace built with bad values that need to work.
This patch works around broken userspace by rounding the requested size
in drm_addmap_core() of any SHM map to the page size. Since the backing
memory for SHM maps is also allocated within addmap_core, there is no
danger of adjacent memory being exposed due to the increased map size.
The only side effect is that drivers that previously tried to create or
access SHM maps using a size < PAGE_SIZE and failed (getting -EINVAL),
will now succeed at the cost of a little bit more memory used if that
happens to be when the map is created.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Eric Paris [Wed, 13 May 2009 16:50:40 +0000 (12:50 -0400)]
TPM: get_event_name stack corruption
get_event_name uses sprintf to fill a buffer declared on the stack. It fills
the buffer 2 bytes at a time. What the code doesn't take into account is that
sprintf(buf, "%02x", data) actually writes 3 bytes. 2 bytes for the data and
then it nul terminates the string. Since we declare buf to be 40 characters
long and then we write 40 bytes of data into buf sprintf is going to write 41
characters. The fix is to leave room in buf for the nul terminator.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Rafael J. Wysocki [Sun, 17 May 2009 18:17:06 +0000 (20:17 +0200)]
PCI PM: Fix initialization and kexec breakage for some devices
Recent PCI PM changes introduced a bug that causes some devices to be
mishandled after kexec and during early initialization. The failure
scenario in the kexec case is the following:
* Assume a PCI device is not power-manageable by the platform and has
PCI_PM_CTRL_NO_SOFT_RESET set in PMCSR.
* The device is put into D3 before kexec (using the native PCI PM).
* After kexec, pci_setup_device() sets the device's power state to
PCI_UNKNOWN.
* pci_set_power_state(dev, PCI_D0) is called by the device's driver.
* __pci_start_power_transition(dev, PCI_D0) is called and since the
device is not power-manageable by the platform, it causes
pci_update_current_state(dev, PCI_D0) to be called. As a result
the device's current_state field is updated to PCI_D3, in
accordance with the contents of its PCI PM registers.
* pci_raw_set_power_state() is called and it changes the device power
state to D0. *However*, it should also call pci_restore_bars() to
reinitialize the device, but it doesn't, because the device's
current_state field has been modified earlier.
To prevent this from happening, modify pci_platform_power_transition()
so that it doesn't use pci_update_current_state() to update the
current_state field for devices that aren't power-manageable by the
platform. Instead, this field should be updated directly for devices
that don't support the native PCI PM.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Thomas Gleixner [Mon, 18 May 2009 19:20:10 +0000 (21:20 +0200)]
futex: setup writeable mapping for futex ops which modify user space data
The futex code installs a read only mapping via get_user_pages_fast()
even if the futex op function has to modify user space data. The
eventual fault was fixed up by futex_handle_fault() which walked the
VMA with mmap_sem held.
After the cleanup patches which removed the mmap_sem dependency of the
futex code commit
4dc5b7a36a49eff97050894cf1b3a9a02523717 (futex:
clean up fault logic) removed the private VMA walk logic from the
futex code. This change results in a stale RO mapping which is not
fixed up.
Instead of reintroducing the previous fault logic we set up the
mapping in get_user_pages_fast() read/write for all operations which
modify user space data. Also handle private futexes in the same way
and make the current unconditional access_ok(VERIFY_WRITE) depend on
the futex op.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
CC: stable@kernel.org
Nico Schottelius [Sat, 16 May 2009 12:00:56 +0000 (14:00 +0200)]
Fix scripts/setlocalversion with tagged git commit
Produce correct output for
- tagged commit (v2.6.30-rc6)
- past tagged commit (
v2.6.30-rc5-299-g7c7327d)
- no tag
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nelson Castillo [Tue, 12 May 2009 20:26:47 +0000 (13:26 -0700)]
mfd: pcf50633: fix unsafe disable_irq()
Without this change Openmoko Freerunner (GTA02) bootstrap will deadlock.
As pointed out in other patches this issue is in the wild since the merge
of:
: commit
3aa551c9b4c40018f0e261a178e3d25478dc04a9
: Author: Thomas Gleixner <tglx@linutronix.de>
: Date: Mon Mar 23 18:28:15 2009 +0100
:
: genirq: add threaded interrupt handler support
:
: Add support for threaded interrupt handlers
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <balajirrao@openmoko.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Thu, 30 Apr 2009 13:48:36 +0000 (14:48 +0100)]
mfd: Keep a cache of WM8350 volatile values
Due to the way that the WM8350 audio driver handles CODEC_ENA many of
the WM8350 audio registers are marked as volatile when they aren't
actually so. Allow the audio driver to see a cache of these values for
inspection during interrupt context.
To do this we need to stop satisfying any bits from volatile registers
from cache - there's no real benefit from doing so anyway, we did the
read already.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Linus Torvalds [Tue, 19 May 2009 18:31:56 +0000 (11:31 -0700)]
Merge branch 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze
* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Fix kind-of-intr checking against number of interrupts
microblaze: Update Microblaze defconfig
Linus Torvalds [Tue, 19 May 2009 18:31:24 +0000 (11:31 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: da903x: add missing __devexit_p()
Linus Torvalds [Tue, 19 May 2009 18:25:35 +0000 (11:25 -0700)]
Avoid ICE in get_random_int() with gcc-3.4.5
Martin Knoblauch reports that trying to build 2.6.30-rc6-git3 with
RHEL4.3 userspace (gcc (GCC) 3.4.5
20051201 (Red Hat 3.4.5-2)) causes an
internal compiler error (ICE):
drivers/char/random.c: In function `get_random_int':
drivers/char/random.c:1672: error: unrecognizable insn:
(insn 202 148 150 0 /scratch/build/linux-2.6.30-rc6-git3/arch/x86/include/asm/tsc.h:23 (set (reg:SI 0 ax [91])
(subreg:SI (plus:DI (plus:DI (reg:DI 0 ax [88])
(subreg:DI (reg:SI 6 bp) 0))
(const_int -4 [0xfffffffffffffffc])) 0)) -1 (nil)
(nil))
drivers/char/random.c:1672: internal compiler error: in extract_insn, at recog.c:2083
and after some debugging it turns out that it's due to the code trying
to figure out the rough value of the current stack pointer by taking an
address of an uninitialized variable and casting that to an integer.
This is clearly a compiler bug, but it's not worth fighting - while the
current stack kernel pointer might be somewhat hard to predict in user
space, it's also not generally going to change for a lot of the call
chains for a particular process.
So just drop it, and mumble some incoherent curses at the compiler.
Tested-by: Martin Knoblauch <spamtrap@knobisoft.de>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Layton [Tue, 19 May 2009 13:57:03 +0000 (09:57 -0400)]
cifs: fix pointer initialization and checks in cifs_follow_symlink (try #4)
This is the third respin of the patch posted yesterday to fix the error
handling in cifs_follow_symlink. It also includes a fix for a bogus NULL
pointer check in CIFSSMBQueryUnixSymLink that Jeff Moyer spotted.
It's possible for CIFSSMBQueryUnixSymLink to return without setting
target_path to a valid pointer. If that happens then the current value
to which we're initializing this pointer could cause an oops when it's
kfree'd.
This patch is a little more comprehensive than the last patches. It
reorganizes cifs_follow_link a bit for (hopefully) better readability.
It should also eliminate the uneeded allocation of full_path on servers
without unix extensions (assuming they can get to this point anyway, of
which I'm not convinced).
On a side note, I'm not sure I agree with the logic of enabling this
query even when unix extensions are disabled on the client. It seems
like that should disable this as well. But, changing that is outside the
scope of this fix, so I've left it alone for now.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Christoph Hellwig <hch@inraded.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Ian Campbell [Tue, 19 May 2009 06:27:42 +0000 (08:27 +0200)]
xen/blkfront: fix warning when deleting gendisk on unplug/shutdown
Currently blkfront gives a warning when hot unplugging due to calling
del_gendisk() with interrupts disabled (due to blkif_io_lock).
WARNING: at kernel/softirq.c:124 local_bh_enable+0x36/0x84()
Modules linked in: xenfs xen_netfront ext3 jbd mbcache xen_blkfront
Pid: 13, comm: xenwatch Not tainted 2.6.29-xs5.5.0.13 #3
Call Trace:
[<
c012611c>] warn_slowpath+0x80/0xb6
[<
c0104cf1>] xen_sched_clock+0x16/0x63
[<
c0104710>] xen_force_evtchn_callback+0xc/0x10
[<
c0104e32>] check_events+0x8/0xe
[<
c0104d9b>] xen_restore_fl_direct_end+0x0/0x1
[<
c0103749>] xen_mc_flush+0x10a/0x13f
[<
c0105bd2>] __switch_to+0x114/0x14e
[<
c011d92b>] dequeue_task+0x62/0x70
[<
c0123b6f>] finish_task_switch+0x2b/0x84
[<
c0299877>] schedule+0x66d/0x6e7
[<
c0104710>] xen_force_evtchn_callback+0xc/0x10
[<
c0104710>] xen_force_evtchn_callback+0xc/0x10
[<
c012a642>] local_bh_enable+0x36/0x84
[<
c022f9a7>] sk_filter+0x57/0x5c
[<
c0233dae>] netlink_broadcast+0x1d5/0x315
[<
c01c6371>] kobject_uevent_env+0x28d/0x331
[<
c01e7ead>] device_del+0x10f/0x120
[<
c01e7ec6>] device_unregister+0x8/0x10
[<
c015f86d>] bdi_unregister+0x2d/0x39
[<
c01bf6f4>] unlink_gendisk+0x23/0x3e
[<
c01ac946>] del_gendisk+0x7b/0xe7
[<
d0828c19>] blkfront_closing+0x28/0x6e [xen_blkfront]
[<
d082900c>] backend_changed+0x3ad/0x41d [xen_blkfront]
We can fix this by calling del_gendisk() later in blkfront_closing, after
releasing blkif_io_lock. Since the queue is stopped during the interrupts
disabled phase I don't think there is any danger of an event occuring between
releasing the blkif_io_lock and deleting the disk.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Ian Campbell [Tue, 19 May 2009 06:25:48 +0000 (08:25 +0200)]
xen/blkfront: allow xenbus state transition to Closing->Closed when not Connected
This situation can occur when attempting to attach a block device whose
backend is an empty physical CD-ROM driver. The backend in this case
will go directly from the Initialising state to Closing->Closed.
Previously this would result in a NULL pointer deref on info->gd
(xenbus_dev_fatal does not return as
a1a15ac5 seems to expect)
Cc: stable@kernel.org
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Frans Pop [Tue, 19 May 2009 04:48:38 +0000 (21:48 -0700)]
ipv4: make default for INET_LRO consistent with help text
Commit
e81963b1 ("ipv4: Make INET_LRO a bool instead of tristate.")
changed this config from tristate to bool. Add default so that it is
consistent with the help text.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Chenault [Tue, 19 May 2009 04:43:27 +0000 (21:43 -0700)]
net: fix skb_seq_read returning wrong offset/length for page frag data
When called with a consumed value that is less than skb_headlen(skb)
bytes into a page frag, skb_seq_read() incorrectly returns an
offset/length relative to skb->data. Ensure that data which should come
from a page frag does.
Signed-off-by: Thomas Chenault <thomas_chenault@dell.com>
Tested-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Filz [Mon, 18 May 2009 21:41:40 +0000 (17:41 -0400)]
nfs: Fix NFS v4 client handling of MAY_EXEC in nfs_permission.
The problem is that permission checking is skipped if atomic open is
possible, but when exec opens a file, it just opens it O_READONLY which
means EXEC permission will not be checked at that time.
This problem is observed by the following sequence (executed as root):
mount -t nfs4 server:/ /mnt4
echo "ls" >/mnt4/foo
chmod 744 /mnt4/foo
su guest -c "mnt4/foo"
Signed-off-by: Frank Filz <ffilzlnx@us.ibm.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Tested-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Dumazet [Tue, 19 May 2009 02:26:37 +0000 (19:26 -0700)]
pkt_sched: gen_estimator: use 64 bit intermediate counters for bps
gen_estimator can overflow bps (bytes per second) with Gb links, while
it was designed with a u32 API, with a theorical limit of 34360Mbit
(2^32 bytes)
Using 64 bit intermediate avbps/brate counters can allow us to reach
this theorical limit.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Mon, 18 May 2009 22:38:55 +0000 (15:38 -0700)]
be2net: add two new pci device ids to pci device table
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 18 May 2009 22:12:31 +0000 (15:12 -0700)]
sch_teql: should not dereference skb after ndo_start_xmit()
It is illegal to dereference a skb after a successful ndo_start_xmit()
call. We must store skb length in a local variable instead.
Bug was introduced in 2.6.27 by commit
0abf77e55a2459aa9905be4b226e4729d5b4f0cb
(net_sched: Add accessor function for packet length for qdiscs)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Sun, 10 May 2009 20:32:34 +0000 (20:32 +0000)]
tcp: fix MSG_PEEK race check
Commit
518a09ef11 (tcp: Fix recvmsg MSG_PEEK influence of
blocking behavior) lets the loop run longer than the race check
did previously expect, so we need to be more careful with this
check and consider the work we have been doing.
I tried my best to deal with urg hole madness too which happens
here:
if (!sock_flag(sk, SOCK_URGINLINE)) {
++*seq;
...
by using additional offset by one but I certainly have very
little interest in testing that part.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Frans Pop <elendil@planet.nl>
Tested-by: Ian Zimmermann <itz@buug.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Moore [Mon, 18 May 2009 18:57:24 +0000 (12:57 -0600)]
[SCSI] mpt2sas: fix driver version inconsistency
In Commit
commit
3b8b5c9b1f08660583e5dfe095c24170df62f1d2
Author: Eric Moore <eric.moore@lsi.com>
Date: Tue Apr 21 15:44:27 2009 -0600
[SCSI] mpt2sas : bump driver version to 01.100.02.00
The MPT2SAS_MAJOR_VERSION didn't get bumped from 00 to 01 so
applications will see it incorrectly as 00.100.02.00 driver instead of
01.100.02.00. Fix by making MPT2SAS_MAJOR_VERSION match the major
number in MPT2SAS_DRIVER_VERSION
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Linus Torvalds [Mon, 18 May 2009 17:22:04 +0000 (10:22 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Explicit alignment for .data.cacheline_aligned
powerpc/ps3: Update ps3_defconfig
powerpc/ftrace: Fix constraint to be early clobber
powerpc/ftrace: Use pr_devel() in ftrace.c
powerpc: Do not assert pte_locked for hugepage PTE entries
Linus Torvalds [Mon, 18 May 2009 17:11:06 +0000 (10:11 -0700)]
Merge branches 'sched-fixes-for-linus-2' and 'core-fixes-for-linus-2' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix fallback sched_clock()'s offset when using jiffies
* 'core-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: increase MAX_LOCKDEP_ENTRIES and MAX_LOCKDEP_CHAINS
Rabin Vincent [Mon, 18 May 2009 16:26:08 +0000 (17:26 +0100)]
[ARM] 5517/1: integrator: don't put clock lookups in __initdata
Remove the __initdata annotation for the clock lookups, since they
will be needed when loading modules which use clk_get().
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rabin Vincent [Mon, 18 May 2009 16:29:30 +0000 (17:29 +0100)]
[ARM] 5518/1: versatile: don't put clock lookups in __initdata
Remove the __initdata annotation for the clock lookups, since they
will be needed when loading modules which use clk_get().
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Mon, 18 May 2009 16:17:37 +0000 (09:17 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix performance regression caused by paravirt_ops on native kernels
xen: use header for EXPORT_SYMBOL_GPL
x86, 32-bit: fix kernel_trap_sp()
x86: fix percpu_{to,from}_op()
x86: mtrr: Fix high_width computation when phys-addr is >= 44bit
x86: Fix false positive section mismatch warnings in the apic code
Linus Torvalds [Mon, 18 May 2009 16:15:41 +0000 (09:15 -0700)]
Merge branch 'tracing-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Append prompt in /debug/tracing/README file
x86/function-graph: fix constraint for recording old return value
David Woodhouse [Mon, 18 May 2009 12:07:35 +0000 (13:07 +0100)]
Fix oops on close of hot-unplugged FTDI serial converter
Commit
c45d6320 ("fix reference counting of ftdi_private") stopped
ftdi_sio_port_remove() from directly freeing the port-private data, with
the intention if the port was still open, it would be freed when
ftdi_close() is eventually called and releases the last refcount on the
structure.
That's all very well, but ftdi_sio_port_remove() still contains a call
to usb_set_serial_port_data(port, NULL) -- so by the time we get to
ftdi_close() for the port which was unplugged, it _still_ oopses on
dereferencing that NULL pointer, as it did before (and does in 2.6.29).
The fix is just not to clear the private data in ftdi_sio_port_remove().
Then the refcount is properly reduced to zero when the final kref_put()
happens in ftdi_close().
Remove a bogus comment too, while we're at it. And stop doing things
inside "if (priv)" -- it must _always_ be there.
Based loosely on an earlier patch by Daniel Mack, and suggestions by
Alan Stern.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Korsgaard [Mon, 18 May 2009 10:13:54 +0000 (11:13 +0100)]
mtd_dataflash: unbreak erase support
Commit
5b7f3a50 (fix dataflash 64-bit divisions) unfortunately
introduced a typo. Erase addr and len were swapped in the pageaddr
calculation, causing the wrong sectors to get erased.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roel Kluin [Mon, 18 May 2009 01:18:58 +0000 (18:18 -0700)]
asm-generic: fix local_add_unless macro
`local_add_unless(x, y, z)' will be expanded to `(&(x)->y, (y), (x))', but
`&(x)->y' should be `&(x)->a'
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Simek [Thu, 14 May 2009 11:35:52 +0000 (13:35 +0200)]
microblaze: Fix kind-of-intr checking against number of interrupts
+ Fix typographic fault.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Michal Simek [Mon, 11 May 2009 07:24:47 +0000 (09:24 +0200)]
microblaze: Update Microblaze defconfig
Signed-off-by: Michal Simek <monstr@monstr.eu>
Pavel Roskin [Tue, 12 May 2009 20:36:46 +0000 (13:36 -0700)]
[ARM] mach-l7200: fix spelling of SYS_CLOCK_OFF
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mel Gorman [Wed, 13 May 2009 16:34:48 +0000 (17:34 +0100)]
[ARM] Double check memmap is actually valid with a memmap has unexpected holes V2
pfn_valid() is meant to be able to tell if a given PFN has valid memmap
associated with it or not. In FLATMEM, it is expected that holes always
have valid memmap as long as there is valid PFNs either side of the hole.
In SPARSEMEM, it is assumed that a valid section has a memmap for the
entire section.
However, ARM and maybe other embedded architectures in the future free
memmap backing holes to save memory on the assumption the memmap is never
used. The page_zone linkages are then broken even though pfn_valid()
returns true. A walker of the full memmap must then do this additional
check to ensure the memmap they are looking at is sane by making sure the
zone and PFN linkages are still valid. This is expensive, but walkers of
the full memmap are extremely rare.
This was caught before for FLATMEM and hacked around but it hits again for
SPARSEMEM because the page_zone linkages can look ok where the PFN linkages
are totally screwed. This looks like a hatchet job but the reality is that
any clean solution would end up consumning all the memory saved by punching
these unexpected holes in the memmap. For example, we tried marking the
memmap within the section invalid but the section size exceeds the size of
the hole in most cases so pfn_valid() starts returning false where valid
memmap exists. Shrinking the size of the section would increase memory
consumption offsetting the gains.
This patch identifies when an architecture is punching unexpected holes
in the memmap that the memory model cannot automatically detect and sets
ARCH_HAS_HOLES_MEMORYMODEL. At the moment, this is restricted to EP93xx
which is the model sub-architecture this has been reported on but may expand
later. When set, walkers of the full memmap must call memmap_valid_within()
for each PFN and passing in what it expects the page and zone to be for
that PFN. If it finds the linkages to be broken, it assumes the memmap is
invalid for that PFN.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mike Frysinger [Fri, 15 May 2009 18:50:33 +0000 (14:50 -0400)]
regulator: da903x: add missing __devexit_p()
The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Liam Girdwood <lrg@slimlogic.co.uk>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Eric Miao <eric.miao@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Benjamin Herrenschmidt [Sun, 17 May 2009 18:29:03 +0000 (18:29 +0000)]
powerpc: Explicit alignment for .data.cacheline_aligned
I don't think anything guarantees that the objects in data.page_aligned
are a multiple of PAGE_SIZE, thus the section may end on any boundary.
So the following section, .data.cacheline_aligned needs an explicit
alignment.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Geoff Levand [Fri, 15 May 2009 08:01:59 +0000 (08:01 +0000)]
powerpc/ps3: Update ps3_defconfig
Refresh and set these options:
CONFIG_SYSFS_DEPRECATED_V2: y -> n
CONFIG_INPUT_JOYSTICK: y -> n
CONFIG_HID_SONY: n -> m
CONFIG_RTC_DRV_PS3: - -> m
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Steven Rostedt [Fri, 15 May 2009 04:33:54 +0000 (04:33 +0000)]
powerpc/ftrace: Fix constraint to be early clobber
After upgrading my distcc boxes from gcc 4.2.2 to 4.4.0, the function
graph tracer broke. This was discovered on my x86 boxes.
The issue is that gcc used the same register for an output as it did for
an input in an asm statement. I first thought this was a bug in gcc and
reported it. I was notified that gcc was correct and that the output had
to be flagged as an "early clobber".
I noticed that powerpc had the same issue and this patch fixes it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Wed, 13 May 2009 20:30:24 +0000 (20:30 +0000)]
powerpc/ftrace: Use pr_devel() in ftrace.c
pr_debug() can now result in code being generated even when #DEBUG
is not defined. That's not really desirable in the ftrace code
which we want to be snappy.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
3334 672 4 4010 faa arch/powerpc/kernel/ftrace.o
size after:
text data bss dec hex filename
2616 360 4 2980 ba4 arch/powerpc/kernel/ftrace.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mel Gorman [Thu, 30 Apr 2009 10:59:19 +0000 (10:59 +0000)]
powerpc: Do not assert pte_locked for hugepage PTE entries
With CONFIG_DEBUG_VM, an assertion is made when changing the protection
flags of a PTE that the PTE is locked. Huge pages use a different pagetable
format and the assertion is bogus and will always trigger with a bug looking
something like
Unable to handle kernel paging request for data at address 0xf1a00235800006f8
Faulting instruction address: 0xc000000000034a80
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=32 NUMA Maple
Modules linked in: dm_snapshot dm_mirror dm_region_hash
dm_log dm_mod loop evdev ext3 jbd mbcache sg sd_mod ide_pci_generic
pata_amd ata_generic ipr libata tg3 libphy scsi_mod windfarm_pid
windfarm_smu_sat windfarm_max6690_sensor windfarm_lm75_sensor
windfarm_cpufreq_clamp windfarm_core i2c_powermac
NIP:
c000000000034a80 LR:
c000000000034b18 CTR:
0000000000000003
REGS:
c000000003037600 TRAP: 0300 Not tainted (2.6.30-rc3-autokern1)
MSR:
9000000000009032 <EE,ME,IR,DR> CR:
28002484 XER:
200fffff
DAR:
f1a00235800006f8, DSISR:
0000000040010000
TASK =
c0000002e54cc740[2960] 'map_high_trunca' THREAD:
c000000003034000 CPU: 2
GPR00:
4000000000000000 c000000003037880 c000000000895d30 c0000002e5a2e500
GPR04:
00000000a0000000 c0000002edc40880 0000005700000393 0000000000000001
GPR08:
f000000011ac0000 01a00235800006e8 00000000000000f5 f1a00235800006e8
GPR12:
0000000028000484 c0000000008dd780 0000000000001000 0000000000000000
GPR16:
fffffffffffff000 0000000000000000 00000000a0000000 c000000003037a20
GPR20:
c0000002e5f4ece8 0000000000001000 c0000002edc40880 0000000000000000
GPR24:
c0000002e5f4ece8 0000000000000000 00000000a0000000 c0000002e5f4ece8
GPR28:
0000005700000393 c0000002e5a2e500 00000000a0000000 c000000003037880
NIP [
c000000000034a80] .assert_pte_locked+0xa4/0xd0
LR [
c000000000034b18] .ptep_set_access_flags+0x6c/0xb4
Call Trace:
[
c000000003037880] [
c000000003037990] 0xc000000003037990 (unreliable)
[
c000000003037910] [
c000000000034b18] .ptep_set_access_flags+0x6c/0xb4
[
c0000000030379b0] [
c00000000014bef8] .hugetlb_cow+0x124/0x674
[
c000000003037b00] [
c00000000014c930] .hugetlb_fault+0x4e8/0x6f8
[
c000000003037c00] [
c00000000013443c] .handle_mm_fault+0xac/0x828
[
c000000003037cf0] [
c0000000000340a8] .do_page_fault+0x39c/0x584
[
c000000003037e30] [
c0000000000057b0] handle_page_fault+0x20/0x5c
Instruction dump:
7d29582a 7d200074 7800d182 0b000000 3c004000 3960ffff 780007c6 796b00c4
7d290214 7929a302 1d290068 7d6b4a14 <
800b0010>
7c000074 7800d182 0b000000
This patch fixes the problem by not asseting the PTE is locked for VMAs
backed by huge pages.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Wang Tinggong [Thu, 14 May 2009 22:49:36 +0000 (22:49 +0000)]
Doc: fixed descriptions on /proc/sys/net/core/* and /proc/sys/net/unix/*
Signed-off-by: Wang Tinggong <wangtinggong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
roel kluin [Fri, 15 May 2009 10:19:51 +0000 (10:19 +0000)]
Neterion: *FIFO1_DMA_ERR set twice, should 2nd be *FIFO2_DMA_ERR?
FIFO1_DMA_ERR is set twice, the second should be FIFO2_DMA_ERR.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Ram Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gabriel Paubert [Mon, 18 May 2009 04:16:47 +0000 (21:16 -0700)]
mv643xx_eth: fix PPC DMA breakage
After 2.6.29, PPC no more admits passing NULL to the dev parameter of
the DMA API. The result is a BUG followed by solid lock-up when the
mv643xx_eth driver brings an interface up. The following patch makes
the driver work on my Pegasos again; it is mostly a search and replace
of NULL by mp->dev->dev.parent in dma allocation/freeing/mapping/unmapping
functions.
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 15 May 2009 08:44:32 +0000 (08:44 +0000)]
bonding: fix link down handling in 802.3ad mode
One of the purposes of bonding is to allow for redundant links, and failover
correctly if the cable is pulled. If all the members of a bonded device have
no carrier present, the bonded device itself needs to report no carrier present
to user space so management tools (like routing daemons) can respond.
Bonding in 802.3ad mode does not work correctly for this because it incorrectly
chooses a link that is down as a possible aggregator.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 18 May 2009 04:14:33 +0000 (21:14 -0700)]
Merge branch 'linux-2.6.30.y' of git://git./linux/kernel/git/inaky/wimax
Stephen Hemminger [Fri, 15 May 2009 06:11:58 +0000 (06:11 +0000)]
bridge: fix initial packet flood if !STP
If bridge is configured with no STP and forwarding delay of 0 (which
is typical for virtualization) then when link starts it will flood all
packets for the first 20 seconds.
This bug was introduced by a combination of earlier changes:
* forwarding database uses hold time of zero to indicate
user wants to always flood packets
* optimzation of the case of forwarding delay of 0 avoids the initial
timer tick
The fix is to just skip all the topology change detection code if
kernel STP is not being used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>