Felix Fietkau [Wed, 6 Jul 2022 12:06:30 +0000 (14:06 +0200)]
mediatek: add filogic subtarget
Initially this covers MT7986 only, but it will later be expanded to cover other
Filogic branded platforms by MediaTek
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Sam Shih [Sun, 10 Apr 2022 12:49:09 +0000 (20:49 +0800)]
mediatek: add mt7986 soc support to the target
It will be supported by the new filogic subtarget
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 15 Aug 2022 11:19:15 +0000 (13:19 +0200)]
uboot-mediatek: no compression means IH_COMP_NONE
Treat missing compression node in FIT image as IH_COMP_NONE.
This is implicentely already happening in most places, but for now
was still triggering an annoying warning about initramfs compression
being obsolete despite compression note being absent.
Fix this.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 17 Jul 2022 20:42:05 +0000 (21:42 +0100)]
uboot-mediatek: mt7986: add generic reset button support
Allow resetting environment to default values when defined button
exists in device tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 12 Aug 2022 21:31:49 +0000 (23:31 +0200)]
uboot-mediatek: mt7986: support PSTORE/ramoops
Assign reserved memory for PSTORE/ramoops for the MT7986 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 7 Aug 2022 10:06:56 +0000 (12:06 +0200)]
uboot-mediatek: additions from MTK SDK
* updated SNAND/SNFI driver brings support for MT7981
* add support for MediaTek NAND Memory bad Block Management (NMBM)
(not used for any boards atm, but could be useful in future)
* wire up NMBM support for MT7622, MT7629, MT7981 and MT7986
* replace some local patches with updated version from SDK
* bring some legacy precompiler symbols which haven't been converted
into Kconfig symbols in U-Boot 2022.07, remove when bumbping to
U-Boot 2022.10:
100-28-include-configs-mt7986-h-from-SDK.patch
Source: https://github.com/mtk-openwrt/u-boot
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 12 Jul 2022 02:41:30 +0000 (03:41 +0100)]
uboot-mediatek: add support for MT798x platforms
Import pending patches to support the upcoming Filogic platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 13 Jul 2022 20:06:36 +0000 (21:06 +0100)]
uboot-mediatek: add support for compressed BL3/FIP image
MediaTek's ARM Trusted Firmware v2.7+ allows the images inside a FIP
structure to be compressed. Make use of that for boards with NOR flash.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 28 Aug 2022 19:20:31 +0000 (20:20 +0100)]
uboot-mediatek: fix factory reset on UBI
Truncating a UBI volume using `ubi write 0x0 volname 0x0` results in
segfault on newer U-Boot. Write 1MB of 0s instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 13 Aug 2022 11:54:52 +0000 (12:54 +0100)]
arm-trusted-firmware-mediatek: update to v2.7+ from MediaTek
The updated sources bring support for the MT798x Filogic SoC family.
Add builds for MT7986 with most supported storage types, each for DDR3
and DDR4 configurations.
A better solution for skipping bad blocks on SPI-NAND connected via the
SNFI interface has been implemented upstream, so drop local patch.
Add pending patches [1] and [2] to fix boot on existing MT7622 boards.
Tested on BananaPi BPi-R64 (SDMMC, eMMC, SPI-NAND), Linksys E8450 and
Ubiquiti UniFi 6 LR as well as upcoming Bananapi BPi-R3 board for which
support will be added in future patches.
[1]: https://github.com/mtk-openwrt/arm-trusted-firmware/pulls/#3
[2]: https://github.com/mtk-openwrt/arm-trusted-firmware/pulls/#4
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 11 Aug 2022 21:29:52 +0000 (23:29 +0200)]
trusted-firmware-a.mk: pass DTC path similar to u-boot.mk
Instead of relying on dtc being provided by the build host use the
dtc from $(LINUX_DIR) similar to how it's done also in u-boot.mk.
For this to work kernel.mk now needs to be included before
trusted-firmware-a.mk, add this include to all affected packages.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 5 Aug 2022 12:18:20 +0000 (14:18 +0200)]
tools: mkimage: Add support for MediaTek MT798x
Import pending patches for mtk_image to support BootROM headers of
newer MediaTek SoCs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Nick Hainke [Tue, 23 Aug 2022 18:53:56 +0000 (20:53 +0200)]
popt: update to 1.18
Changes from popt 1.16:
- fix an ugly and ancient security issue with popt failing to drop privileges on alias exec from a SUID/SGID program
- perform rudimentary sanity checks when reading in popt config files
- collect accumulated misc fixes (memleaks etc) from distros
- convert translations to utf-8 encoding
- convert old postscript documentation to pdf
- dust off ten years worth of autotools sediment
- reorganize and clean up the source tree for clarity
- remove the obnoxious splint annotations from the sources
Switch to new mirror:
http://ftp.rpm.org/popt/releases/
Switch URL to:
https://github.com/rpm-software-management/popt
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sat, 13 Aug 2022 20:41:54 +0000 (22:41 +0200)]
nftables: update to 1.0.5
Remove upstreamed patch:
- 0001-meta-don-t-use-non-POSIX-formats-in-strptime.patch
Changes:
13248670 build: Bump version to 1.0.5
3432eebd tests/py: disable arp family for queue statement
180ce4d7 meta: don't use non-POSIX formats in strptime()
c1c223f1 src: allow anon set concatenation with ether and vlan
87c3041b evaluate: search stacked header list for matching payload dep
b1e3ed03 netlink_delinearize: also postprocess OP_AND in set element context
f680055c tests: add a test case for ether and vlan listing
dbd5f348 debug: dump the l2 protocol stack
0d9daa04 proto: track full stack of seen l2 protocols, not just cumulative offset
89688c94 netlink_delinearize: postprocess binary ands in concatenations
0542a431 netlink_delinearize: allow postprocessing on concatenated elements
8efab552 parser_json: fix device parsing in netdev family
76fae8f5 src: proto: support DF, LE PHB, VA for DSCP
446e76db doc: Document limitations of ipsec expression with xfrm_interface
a2ddb38f cache: report an error message if cache initialization fails
649b8ce3 cache: validate handle string length
64c74ba5 cache: prepare nft_cache_evaluate() to return error
46980cdd rule: crash when uncollapsing command with unexisting table or set
8a6cdfaf cache: release pending rules when chain binding lookup fails
e17337df evaluate: report missing interval flag when using prefix/range in concatenation
45c097c6 scanner: allow prefix in ip6 scope
6c23bfa5 segtree: fix map listing with interface wildcard
8623772a scanner: don't pop active flex scanner scope
994bf500 parser: add missing synproxy scope closure
ed2426bc tests/py: Add a test for failing ipsec after counter
27107b49 evaluate: fix segfault when adding elements to invalid set
0f82b07f mnl: store netlink error location for set elements
15b3be2e src: remove NFT_NLATTR_LOC_MAX limit for netlink location error reporting
f56e901a parser_bison: fix error location for set elements
6d1ee926 intervals: check for EXPR_F_REMOVE in case of element mismatch
5357cb7b intervals: fix crash when trying to remove element in empty set
d54510f8 netlink_delinearize: memleak when parsing concatenation data
12a223ce libnftables: release top level scope
b91bbf88 optimize: limit statement is not supported yet
45a61a75 optimize: assume verdict is same when rules have no verdict
fa409176 optimize: only merge OP_IMPLICIT and OP_EQ relational
29e62111 tests: shell: run -c -o on ruleset
887405df optimize: add unsupported statement
8f61a69e optimize: add hash expression support
ca8fd77a optimize: add numgen expression support
721efd64 optimize: add binop expression support
f7e901a2 optimize: add fib expression support
54b1e49f optimize: add xfrm expression support
0beaea37 optimize: add osf expression support
d07fe8e8 optimize: fix verdict map merging
38d48fe5 optimize: fix reject statement
f9939f89 optimize: remove comment after merging
8f10f33a optimize: do not print stateful information
3ac932e9 optimize: do not merge rules with set reference in rhs
64ebb03a optimize: do not compare relational expression rhs when collecting statements
59e3a592 intervals: Do not sort cached set elements over and over again
d434de8b intervals: do not empty cache for maps
87ba510f intervals: do not report exact overlaps for new elements
498a5f0c rule: collapse set element commands
8fafe4e6 tests: shell: runtime set element automerge
638af0ce Revert "scanner: flags: move to own scope"
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sat, 13 Aug 2022 21:15:33 +0000 (23:15 +0200)]
libnftnl: update to 1.2.3
Changes:
817c8b6 build: libnftnl 1.2.3 release
84d12cf build: fix clang+glibc snprintf substitution error
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sat, 27 Aug 2022 12:09:16 +0000 (14:09 +0200)]
iproute2: replace musl-compilation-fix with upstream fix
Instead of defining the MIN version it is enough to include "#include
<sys/param.h>".
Delete patch:
- 105-ipstats-Define-MIN-function-to-fix-undefined-referen.patch
Add patch:
- 010-ipstats-Add-param.h-for-musl.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Tue, 23 Aug 2022 12:09:20 +0000 (14:09 +0200)]
wireguard-tools: update to v1.0.
20210914
Update to latest version.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Tue, 23 Aug 2022 11:53:16 +0000 (13:53 +0200)]
ethtool: update to 5.19
Release Notes:
https://lore.kernel.org/netdev/
20220821234539.f7nslwyd53bsftsy@lion.mk-sys.cz/T/
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Tue, 23 Aug 2022 12:00:18 +0000 (14:00 +0200)]
strace: update to 5.19
Release Notes:
https://strace.io/files/5.19/
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Mon, 22 Aug 2022 08:17:33 +0000 (10:17 +0200)]
toolchain: bump GCC 12 to 12.2.0
Refreshed patches:
- 910-mbsd_multi.patch
- 970-macos_arm64-building-fix.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Daniel Golle [Sun, 28 Aug 2022 15:07:05 +0000 (16:07 +0100)]
uboot-envtools: mt7622: use 4k sectors for UniFi 6 LR (ubootmod)
Use 4k sectors when accessing the U-Boot environment on the 64MiB
SPI-NOR flash chip found in the UniFi 6 LR. The speeds up environment
write access as only 4kB instead of 64kB have to be written.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 28 Aug 2022 15:05:30 +0000 (16:05 +0100)]
mediatek: mt7622: use variable sector size for spi-nor
Make use of minor sector size (4k) on supported SPI-NOR flash chips.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 28 Aug 2022 15:01:12 +0000 (16:01 +0100)]
uboot-mediatek: fix Ubiquiti UniFi 6 LR U-Boot mod
Image names as well as the calculation of the padded image size did
not work as intended. Fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rafał Miłecki [Wed, 17 Aug 2022 21:20:45 +0000 (23:20 +0200)]
kernel: replace downstream get_mtd_device_by_node() implementation
Use upstream of_get_mtd_device_by_node() which should behave pretty much
the same. Implementation differences:
get_mtd_device_by_node() of_get_mtd_device_by_node()
---- ----
np->dev.of_node mtd_get_of_node(np)
-EPROBE_DEFER -ENODEV
Cc: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
Cc: Bernhard Frauendienst <kernel@nospam.obeliks.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Hauke Mehrtens [Sat, 27 Aug 2022 21:11:30 +0000 (23:11 +0200)]
mbedtls: update to version 2.28.1
Changelog: https://github.com/Mbed-TLS/mbedtls/releases/tag/v2.28.1
This release of Mbed TLS provides bug fixes and minor enhancements. This
release includes fixes for security issues.
The build problem was reported upstream:
https://github.com/Mbed-TLS/mbedtls/issues/6243
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Markus Stockhausen [Thu, 25 Aug 2022 06:24:13 +0000 (08:24 +0200)]
realtek: switch RTL838X/RTL839X DT to new clock driver
Use new DT clockdriver syntax for RTL838X/RTL839X targets. To make it work
we need to change some nodes:
- define the external oscillator speed (25MHz)
- define SRAM
- add clock controller
- Add second CPU for RTL839X
- map all devices to new clocks
- Remove dummy LXB clock
- add CPU OPP table
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Markus Stockhausen [Thu, 25 Aug 2022 06:23:45 +0000 (08:23 +0200)]
realtek: activate clock driver for RTL838X/RTL839X targets
Make use the new clock driver for RTL838X and RTL839x target devices. Of course
we will enable their primary consumer (cpufreq-dt) too. To be careful just set
the default governor to userspace. As we rely on SRAM activate that module too.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Markus Stockhausen [Thu, 25 Aug 2022 06:23:02 +0000 (08:23 +0200)]
realtek: enable basic config for cpufreq framework
A new clock driver makes more sense if it can be used from consumers
like cpufreq. Before we enable the driver we must tell the config that
the RTL838X and RTL839X targets allow CPU frequency changing.
Even though these targets currently rely on the CPU's internal R4K
timer, MIPS_EXTERNAL_TIMER is selected to allow for CPU frequency change
testing. The Realtek timers, which are clocked by the Lexra bus, still
need to be supported and used in order to provide correct wall times
when reclocking the CPU.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[add paragraph about MIPS_EXTERNAL_TIMER to commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Markus Stockhausen [Thu, 25 Aug 2022 06:22:36 +0000 (08:22 +0200)]
realtek: add patch to enable new clock driver in kernel
Allow building the clock driver with kernel config options.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Markus Stockhausen [Thu, 25 Aug 2022 06:22:01 +0000 (08:22 +0200)]
realtek: add RTL83XX clock driver
Add a new self-contained combined clock & platform driver that allows to
access the PLL hardware clocks of RTL83XX devices. Currently it provides
info about CPU, MEM and LXB clocks on RTL838X and RTL839X devices and
additionally allows to change the CPU clocks. Changing the clocks
multiple times on a DGS-1210-20 and a DGS-1210-52 already works well and
is multithreading safe on the RTL839X. Even a cpufreq initiated change
of the CPU clock works fine. Loading the driver will add some meaningful
logging.
[0.000000] rtl83xx-clk: initialized, CPU 500 MHz, MEM 300 MHz (8 Bit DDR3), LXB 200 MHz
[0.279456] rtl83xx-clk soc:clock-controller: rate setting enabled, CPU 325-600 MHz,
MEM 300-300 MHz, LXB 200-200 MHz, OVERCLOCK AT OWN RISK
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[remove trailing whitespaces, C-style SPDX comments for ASM and headers]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Markus Stockhausen [Wed, 24 Aug 2022 18:57:05 +0000 (20:57 +0200)]
realtek: add PLL DT binding includes
Add some constants for sharing between DT and drivers.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Etienne Champetier [Sat, 20 Aug 2022 22:08:15 +0000 (18:08 -0400)]
iptables: default to ip(6)tables-nft when using buildroot
35fec487e30f05c81bd135326a993dad7f861812 fixed opkg usage,
but when using buildroot we were still defaulting to
ip(6)tables-legacy
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Felix Fietkau [Tue, 23 Aug 2022 21:29:52 +0000 (23:29 +0200)]
unetd: add WireGuard based VPN connection manager for OpenWrt
This package simplifies setting up wireguard networks on OpenWrt by a wireguard
network as a JSON file, which can be shared across all participating nodes.
It can be signed with an authentication key and automatically kept in sync.
unetd also supports deterministically generating ipv6 addresses for each host
based on the public key and storing those in a hosts file that can be used with
dnsmasq. It also supports automatically creating VXLAN tunnels between multiple
endpoints.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Daniel Golle [Wed, 27 Jul 2022 22:30:12 +0000 (00:30 +0200)]
kernel: add quirk for Huawei-compatible OEM SFP GE-T
Ignore TX_FAULT signal on certain cheap copper/TP gigabit Ethernet SFP
modules.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 26 Aug 2022 21:16:25 +0000 (22:16 +0100)]
ltq-vdsl-fw: fix firmware installer
The downloaded filename was wrong in multiple places. Fix that.
Fixes: 2f95dd8ff0 ("ltq-vdsl-fw: update w921v firmware download URL")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Fri, 26 Aug 2022 17:48:45 +0000 (19:48 +0200)]
mt76: update to the latest version
9485e3b47066 mt76: remove q->qid
e5674c4aa402 mt76: mt7921: enable HW beacon filter not depending on PM flag
7fd299e3c921 mt76: mt7921: enable HW beacon filter in the initialization stage
d5459efaaf14 mt76: mt7921: make mt7921_pci_driver static
b8304b456e23 mt76: connac: move tx initialization/cleanup in mt76_connac module
6e0d7077486c mt76: mt7921: reduce log severity levels for informative messages
cb80da974fe6 mt76: mt7921: reduce the mutex lock scope during reset
a2d61f4f4063 mt76: mt7915 add ht mpdu density
08ea730c1130 mt76: add len parameter to __mt76_mcu_msg_alloc signature
60ef85fa352c mt76: introduce MT_RXQ_BAND2 and MT_RXQ_BAND2_WA in mt76_rxq_id
8ccbb38ca6e6 mt76: add phy_idx in mt76_rx_status
eb19ac83c07e mt76: introduce phys array in mt76_dev structure
30887591e3ab mt76: add phy_idx to mt76_wcid
4bf8c20a9524 mt76: convert MT_TX_HW_QUEUE_EXT_PHY to MT_TX_HW_QUEUE_PHY
e6c6bf8cee09 mt76: get rid of mt76_wcid_hw routine
120f73ad992a mediatek: mt76: mac80211: Fix missing of_node_put() in mt76_led_init()
111e92cf8c22 mediatek: mt76: eeprom: fix missing of_node_put() in mt76_find_power_limits_node()
13bedd62ff4a mt76: connac: introduce mt76_connac_reg_map structure
5ec78e1ec43d wifi: mt76: fix reading current per-tid starting sequence number for aggregation
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Petr Štetiar [Mon, 22 Aug 2022 13:30:21 +0000 (15:30 +0200)]
bcm53xx: 5.15: add missing LEDS_BCM63138 config symbol
Fixes following build issue found during build testing with 5.15.63
kernel:
LED Support for Broadcom BCM63138 SoC (LEDS_BCM63138) [N/m/y/?] (NEW)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
John Audia [Thu, 25 Aug 2022 14:36:19 +0000 (10:36 -0400)]
kernel: bump 5.15 to 5.15.63
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <therealgraysky@proton.me>
Felix Fietkau [Thu, 25 Aug 2022 19:16:00 +0000 (21:16 +0200)]
netifd: update to the latest version
76d2d41b7355 interface: fix use-after-free bug when rewriting resolv.conf
Signed-off-by: Felix Fietkau <nbd@nbd.name>
John Audia [Thu, 25 Aug 2022 14:52:50 +0000 (10:52 -0400)]
kernel: bump 5.10 to 5.10.138
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
Petr Štetiar [Wed, 24 Aug 2022 11:10:37 +0000 (13:10 +0200)]
rpcd: bump version to 2022-08-24
gcc 10 with -O2 reports following:
In function ‘strncpy’,
inlined from ‘rpc_sys_packagelist’ at /opt/devel/openwrt/c-projects/rpcd/sys.c:244:4:
/usr/include/x86_64-linux-gnu/bits/string_fortified.h:106:10: error: ‘__builtin_strncpy’ specified bound 128 equals destination size [-Werror=stringop-truncation]
106 | return __builtin___strncpy_chk (__dest, __src, __len, __bos (__dest));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In function ‘strncpy’,
inlined from ‘rpc_sys_packagelist’ at /opt/devel/openwrt/c-projects/rpcd/sys.c:227:4:
/usr/include/x86_64-linux-gnu/bits/string_fortified.h:106:10: error: ‘__builtin_strncpy’ specified bound 128 equals destination size [-Werror=stringop-truncation]
106 | return __builtin___strncpy_chk (__dest, __src, __len, __bos (__dest));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Since it is not possible to avoid truncation by strncpy, it is necessary
to make sure the result of strncpy is properly NUL-terminated and the
NUL must be inserted explicitly, after strncpy has returned.
References: #10442
Reported-by: Alexey Smirnov <s.alexey@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Jo-Philipp Wich [Wed, 24 Aug 2022 21:04:45 +0000 (23:04 +0200)]
firewall4: update to latest Git HEAD
a4484d4 fw4: support automatic includes
ca7e3a1 fw4: honour enabled option of include sections
5a02f74 tests: add missing fs.stat) mock data for `nf_conntrack_dummy`
111a7f7 fw4: don't inherit zone family from ct helpers
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jo-Philipp Wich [Fri, 12 Aug 2022 19:37:05 +0000 (21:37 +0200)]
rpcd: update to latest Git HEAD
ae5afea ucode: parse ucode plugin scripts in raw mode, init search path
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jo-Philipp Wich [Fri, 12 Aug 2022 19:24:26 +0000 (21:24 +0200)]
uhttpd: update to latest Git HEAD
e3395cd ucode: initialize search path before VM init
8cb3f85 ucode: initialize default library search path
188dea2 utils: accept '?' as path terminator in uh_path_match()
c5eac5d file: support using dynamic script handlers as error pages
290ff88 relay: trigger close if in header read state with pending data
f9db538 ucode: ignore exit exceptions
8ba0b64 cmake: use variables and find_library for dependency
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jo-Philipp Wich [Wed, 29 Jun 2022 18:19:35 +0000 (20:19 +0200)]
ucode: update to latest Git HEAD
bcdd2cb examples: add module search path initialization and freeing
ee1946f ubus: fix GCC strncpy() truncation warning
131d99c lib: introduce three new functions call(), loadstring() and loadfile()
8e8dae0 lib: introduce helper function for indenting error messages
476f02b lib: simplify include_path()
d84b53a source: avoid null pointer access in uc_source_runpath_set()
c43a54f types: gracefully handle unpatched upvalues in ucv_free()
e2fb11a README.md: document gc() function
b41cb2d main: introduce -g flag to allow enabling periodic gc from cli
85d7885 lib: implement gc()
47528f0 vm: support automatic periodic GC runs
381cc75 types: treat vm->exports as GC roots
fcc49e6 compiler: add import statement support for dynamic extensions
c9442f1 vm: introduce new I_DYNLOAD opcode
b6fd8a2 lib: internally expose new uc_require_library() helper
a486adc vm: don't treat offset 0 special for exceptions
41ccd19 compiler: don't treat offset 0 special at syntax errors
b4a3f68 compiler: improve formatting of nested syntax error messages
5d5dadc program: remove now unused uc_program_export_lookup()
304995b compiler: rework export index allocation
506cc37 compiler: fix deriving module path from source runpath
54b7fac compiler: enforce stricter module compilation rules
d62e372 vm: don't initialize upvalues for module functions
b856602 program: add serialization and deserialization for module function flag
d7d1bde compiler: add a flag denoting module functions
156d584 treewide: unexport libucode internal functions
10e056d compiler: add support for import/export statements
862e49d compiler: resolve predeclared upvalues
78dfb08 compiler: require a name in function declarations
afd78c1 compiler: fix reported source position in inc/dec operator error
e1c3db0 tests: run_tests.sh: substitute dynamic test directory path in output
3c168b5 vm, cli: move search path into global configuration structure
d85bc71 vm: introduce import and export opcodes
365782e vm: honor constant flag of objects and arrays
6becc64 vm: transparently resolve upvalue references
3418967 vm: gracefully handle unresolved upvalues
50cf572 program: add function to globally lookup exported name
c441f65 program: add infrastructure to handle multiple sources per program
2322468 program: fix reporting source position of first instruction
9c9a9ec program: fix en/decoding debuginfo upvalue slots in precompiled bytecode
41114a0 source: add tracking of exported symbols
70ae304 lib: honor constant flag of arrays
3c104f5 types: resolve upvalue references on stringification
3a6f9cb types: add ability to mark array and object values as constant
b738f3a lexer: recognize module related keywords
03c8e4b lexer: rewrite token scanner
fd433aa lexer: fix parsing with disabled block left stripping
557577a rtnl: fix parsing/creation of IFLA_AF_SPEC RTA for the AF_BRIDGE family
35c6b73 compiler: fix stack mismatch on continue statements nested in switches
f673096 uloop: end uloop on exceptions in managed code
2e5426c ubus: end uloop on exceptions in managed code
c024270 rtnl: expose IFLA_STATS64 contents
d3c58c0 rtnl: expose ifinfomsg.ifi_change member
c4dde50 rtnl: update NETLINK_GET_STRICT_CHK socket flag with every request
7ef0d02 nl80211: fix NL80211_SURVEY_INFO_NOISE datatype
9a2e592 compiler: fix stack mismatch on nonmatching switch statements with locals
03c8ca5 nl80211: recognize further NL80211_STA_INFO_* NLAs
a1ed566 struct: add optional offset argument to `unpack()`
230e595 rtnl: fix segmentation fault on parsing linkinfo RTA without data
523566d rtnl: zero request message headers
56be30d rtnl: fix premature netlink reply receive abort
1347440 rtnl: avoid stray "netlink: %d bytes leftover after parsing attributes."
44b0a3b struct: fix packing `*` format after other repeated formats
Also package uloop binding module which has been introduced by a previous
ucode update and introduce a host build with the basic set of modules.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Petr Štetiar [Mon, 22 Aug 2022 12:02:36 +0000 (14:02 +0200)]
kernel: bump 5.15 to 5.15.62
Deleted following upstreamed patches:
bcm27xx: 950-0006-drm-vc4-hdmi-Fix-HPD-GPIO-detection.patch
bcm27xx: 950-0420-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch
bcm27xx: 950-0425-drm-vc4-A-present-but-empty-dmas-disables-audio.patch
bcm27xx: 950-0432-vc4-drm-Avoid-full-hdmi-audio-fifo-writes.patch
bcm27xx: 950-0433-vc4-drm-vc4_plane-Remove-subpixel-positioning-check.patch
bcm27xx: 950-0435-drm-vc4-Correct-pixel-order-for-DSI0.patch
bcm27xx: 950-0436-drm-vc4-Register-dsi0-as-the-correct-vc4-encoder-typ.patch
bcm27xx: 950-0437-drm-vc4-Fix-dsi0-interrupt-support.patch
bcm27xx: 950-0438-drm-vc4-Add-correct-stop-condition-to-vc4_dsi_encode.patch
bcm27xx: 950-0443-drm-vc4-Fix-timings-for-interlaced-modes.patch
bcm27xx: 950-0445-drm-vc4-Fix-margin-calculations-for-the-right-bottom.patch
bcm27xx: 950-0475-drm-vc4-Reset-HDMI-MISC_CONTROL-register.patch
bcm27xx: 950-0476-drm-vc4-Release-workaround-buffer-and-DMA-in-error-p.patch
bcm27xx: 950-0477-drm-vc4-Correct-DSI-divider-calculations.patch
bcm27xx: 950-0664-drm-vc4-dsi-Correct-max-divider-to-255-not-7.patch
bcm53xx: 072-next-ARM_dts_BCM53015-add-mr26.patch
mediatek: 920-linux-next-dts-mt7622-bpi-r64-fix-wps-button.patch
Manually rebased following patches:
bcm27xx: 950-0004-drm-vc4-hdmi-Remove-the-DDC-probing-for-status-detec.patch
bcm27xx: 950-0700-net-phy-lan87xx-Decrease-phy-polling-rate.patch
bcm27xx: 950-0711-drm-vc4-Rename-bridge-to-out_bridge.patch
bcm27xx: 950-0713-drm-vc4-Remove-splitting-the-bridge-chain-from-the-d.patch
bcm27xx: 950-0715-drm-vc4-Convert-vc4_dsi-to-using-a-bridge-instead-of.patch
bcm27xx: 950-0787-vc4-drm-vc4_plane-Keep-fractional-source-coords-insi.patch
bcm27xx: 950-0914-mmc-block-Don-t-do-single-sector-reads-during-recove.patch
Runtime tested on turris-omnia and glinet-b1300.
Tested-by: John Audia <therealgraysky@proton.me> [bcm2711/RPi4B, mt7622/RT3200]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 22 Aug 2022 20:45:53 +0000 (22:45 +0200)]
kernel: bump 5.10 to 5.10.137
Removed following upstreamed patch:
* bcm53xx: 081-next-ARM_dts_BCM53015-add-mr26.patch
All other patches automagically rebased.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Christian Marangi [Sun, 21 Aug 2022 16:52:52 +0000 (18:52 +0200)]
ipq806x: add missing scaling_available_frequencies for dedicated cpufreq
Add missing scaling_available_frequencies sysfs entry for dedicated
cpufreq driver.
This sysfs entry is not standard and each cpufreq driver needs to
provide it and declare it in the cpufreq driver struct attr.
Fixes: 5dbbefcbccc0 ("ipq806x: introduce dedicated krait cpufreq")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Sebastian Schaper [Sat, 6 Aug 2022 22:59:06 +0000 (00:59 +0200)]
ath79: add support for ZyXEL NWA1100-NH
Specifications:
* AR9342, 16 MiB Flash, 64 MiB RAM, 802.11n 2T2R, 2.4 GHz
* 1x Gigabit Ethernet (AR8035), 802.3af PoE
Installation:
* OEM Web UI is at 192.168.1.2
login as `admin` with password `1234`
* Flash factory-AASI.bin
The string `AASI` needs to be present within the file name of the uploaded
image to be accepted by the OEM Web-based updater, the factory image is
named accordingly to save the user from the hassle of manual renaming.
TFTP Recovery:
* Open the case, connect to TTL UART port (this is the official method
described by Zyxel, the reset button is useless during power-on)
* Extract factory image (.tar.bz2), serve `vmlinux_mi124_f1e.lzma.uImage`
and `mi124_f1e-jffs2` via tftp at 192.168.1.10
* Interrupt uboot countdown, execute commands
`run lk`
`run lf`
to flash the kernel / filesystem accordingly
MAC addresses as verified by OEM firmware:
use address source
LAN *:cc mib0 0x30 ('eth0mac'), art 0x1002 (label)
2g *:cd mib0 0x4b ('wifi0mac')
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Sebastian Schaper [Sat, 27 Mar 2021 23:33:45 +0000 (00:33 +0100)]
ath79: add support for ZyXEL NWA1123-AC
Specifications:
* AR9342, 16 MiB Flash, 64 MiB RAM, 802.11n 2T2R, 2.4 GHz
* QCA9882 PCIe card, 802.11ac 2T2R
* 1x Gigabit Ethernet (AR8035), 802.3af PoE
Installation:
* OEM Web UI is at 192.168.1.2
login as `admin` with password `1234`
* Flash factory-AAOX.bin
The string `AAOX` needs to be present within the file name of the uploaded
image to be accepted by the OEM Web-based updater, the factory image is
named accordingly to save the user from the hassle of manual renaming.
TFTP Recovery:
* Open the case, connect to TTL UART port (this is the official method
described by Zyxel, the reset button is useless during power-on)
* Extract factory image (.tar.bz2), serve `vmlinux_mi124_f1e.lzma.uImage`
and `mi124_f1e-jffs2` via tftp at 192.168.1.10
* Interrupt uboot countdown, execute commands
`run lk`
`run lf`
to flash the kernel / filesystem accordingly
MAC addresses as verified by OEM firmware:
use address source
LAN *:1c mib0 0x30 ('eth0mac'), art 0x1002 (label)
2g *:1c mib0 0x4b ('wifi0mac')
5g *:1e mib0 0x66 ('wifi1mac')
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Sebastian Schaper [Sat, 27 Mar 2021 23:32:46 +0000 (00:32 +0100)]
ath79: add support for ZyXEL NWA1123-NI
Specifications:
* AR9342, 16 MiB Flash, 64 MiB RAM, 802.11n 2T2R, 2.4 GHz
* AR9382 PCIe card, 802.11n 2T2R, 5 GHz
* 1x Gigabit Ethernet (AR8035), 802.3af PoE
Installation:
* OEM Web UI is at 192.168.1.2
login as `admin` with password `1234`
* Flash factory-AAEO.bin
The string `AAEO` needs to be present within the file name of the uploaded
image to be accepted by the OEM Web-based updater, the factory image is
named accordingly to save the user from the hassle of manual renaming.
TFTP Recovery:
* Open the case, connect to TTL UART port (this is the official method
described by Zyxel, the reset button is useless during power-on)
* Extract factory image (.tar.bz2), serve `vmlinux_mi124_f1e.lzma.uImage`
and `mi124_f1e-jffs2` via tftp at 192.168.1.10
* Interrupt uboot countdown, execute commands
`run lk`
`run lf`
to flash the kernel / filesystem accordingly
MAC addresses as verified by OEM firmware:
use address source
LAN *:fb mib0 0x30 ('eth0mac'), art 0x1002 (label)
2g *:fc mib0 0x4b ('wifi0mac')
5g *:fd mib0 0x66 ('wifi1mac')
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Sebastian Schaper [Wed, 9 Sep 2020 18:42:53 +0000 (20:42 +0200)]
ath79: add support for ZyXEL NWA1121-NI
Specifications:
* AR9342, 16 MiB Flash, 64 MiB RAM, 802.11n 2T2R, 2.4 GHz
* 1x Gigabit Ethernet (AR8035), 802.3af PoE
Installation:
* OEM Web UI is at 192.168.1.2
login as `admin` with password `1234`
* Flash factory-AABJ.bin
The string `AABJ` needs to be present within the file name of the uploaded
image to be accepted by the OEM Web-based updater, the factory image is
named accordingly to save the user from the hassle of manual renaming.
TFTP Recovery:
* Open the case, connect to TTL UART port (this is the official method
described by Zyxel, the reset button is useless during power-on)
* Extract factory image (.tar.bz2), serve `vmlinux_mi124_f1e.lzma.uImage`
and `mi124_f1e-jffs2` via tftp at 192.168.1.10
* Interrupt uboot countdown, execute commands
`run lk`
`run lf`
to flash the kernel / filesystem accordingly
MAC addresses as verified by OEM firmware:
use address source
LAN *:cc mib0 0x30 ('eth0mac'), art 0x1002 (label)
2g *:cd mib0 0x4b ('wifi0mac')
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Nick Hainke [Thu, 18 Aug 2022 05:22:52 +0000 (07:22 +0200)]
tools/cmake: update to 3.24.1
Update cmake to newest version.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Thu, 18 Aug 2022 12:42:01 +0000 (14:42 +0200)]
tools/isl: update to 0.25
Update isl to latest version.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Thu, 18 Aug 2022 12:49:25 +0000 (14:49 +0200)]
tools/xz: update to 5.2.6
This update contains a security fix to xzgrep (CVE-2022-1271,
ZDI-CAN-16587). Release notes:
https://git.tukaani.org/?p=xz.git;a=blob;f=NEWS;hb=HEAD
Signed-off-by: Nick Hainke <vincent@systemli.org>
Arınç ÜNAL [Tue, 5 Jul 2022 22:20:32 +0000 (01:20 +0300)]
ramips: mt7621-dts: mux phy0/4 to gmac1
Mux the MT7530 switch's phy0/4 to the SoC's gmac1 on devices where RGMII2
pins are available. This achieves 2 Gbps total bandwidth to the CPU using
the second RGMII.
The ports called "wan" are muxed where possible. On a minority of devices,
this is not possible. Those cases:
mt7621_ampedwireless_ally-r1900k.dts: lan3
mt7621_ubnt_edgerouter-x.dts: eth0
mt7621_gnubee_gb-pc1.dts: ethblue
mt7621_linksys_re6500.dts: lan1
mt7621_netgear_wac104.dts: lan4
mt7621_tplink_eap235-wall-v1.dts: lan0
mt7621_tplink_eap615-wall-v1.dts: lan0
mt7621_ubnt_usw-flex.dts: lan1
The "wan" port is just what the vendor designated on the board/plastic
chasis of the device. On a technical level, there is no difference between
a lan and wan port on MT7621AT, MT7621DAT and MT7621ST SoCs. Prefer
connecting to WAN via the port described above for these devices to benefit
the feature brought with this patch.
mt7621_d-team_newifi-d2.dts cannot benefit this feature, although it looks
like it should, because the rgmii2 pins are wired to unused components.
Tested on a range of devices documented on the GitHub PR.
Link: https://github.com/openwrt/openwrt/pull/10238
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Arınç ÜNAL [Tue, 5 Jul 2022 14:34:11 +0000 (17:34 +0300)]
ramips: mt7621-dts: remove DTS_LEGACY from ethernet node
Remove DTS_LEGACY put for claiming pin groups for the ethernet node from
the ethernet node. It's not an old kernel trait. These bindings need to be
there on the newer kernels as well.
Fixes: a3764ee29dd0 ("ramips: add linux 5.15 support for mt7621")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Arınç ÜNAL [Sun, 14 Aug 2022 07:44:12 +0000 (10:44 +0300)]
ramips: mt7621-dts: do not claim rgmii2 group as gpio for certain devices
These devices do not use rgmii2 as gpio, therefore remove rgmii2 pin group
from state-default. Remove overwriting the ethernet node for these devices.
Move claiming the rgmii2 group from mt7621_zyxel_nwa-ax.dtsi to
mt7621_zyxel_nwa50ax.dts as it's only the latter using rgmii2 pins as gpio.
Remove duplicate ethernet overwrite from mt7621_tplink_archer-x6-v3.dtsi.
Claim rgmii2 group as gpio on mt7621_bolt_arion.dts as it uses an rgmii2
pin, 26, as gpio.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Arınç ÜNAL [Tue, 5 Jul 2022 14:10:43 +0000 (17:10 +0300)]
ramips: fix GB-PC1 and GB-PC2 device support
Change switch port labels to ethblack & ethblue.
Change lan1 & lan2 LEDs to ethblack_act & ethblue_act and fix GPIO pins.
Add the external phy with ethyellow label on the GB-PC2 devicetree.
Do not claim rgmii2 as gpio, it's used for ethernet with rgmii2 function.
Enable ICPlus PHY driver for IP1001 which GB-PC2 has got.
Update interface name and change netdev function.
Enable lzma compression to make up for the increased size of the kernel.
Make spi flash bindings on par with mainline Linux to fix read errors.
Tested on GB-PC2 by Petr.
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Joerg Werner [Sun, 26 Jun 2022 15:18:39 +0000 (17:18 +0200)]
hostapd: fix WPA3 enterprise keys and ciphers
WPA3 enterprise requires group_mgmt_cipher=BIP-GMAC-256 and if 802.11r is
active also wpa_key_mgmt FT-EAP-SHA384. This commit also requires
corresponding changes in netifd.
Signed-off-by: Joerg Werner <schreibubi@gmail.com>
Hauke Mehrtens [Sat, 20 Aug 2022 20:52:49 +0000 (22:52 +0200)]
netifd: update to git HEAD
87fbefd interface: support "zone" config option
bfa039c netifd: fix WPA3 enterprise ciphers
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 20 Aug 2022 20:51:29 +0000 (22:51 +0200)]
iwinfo: update to latest HEAD
0dad3e6 Add support for CCMP-256 and GCMP-256 ciphers
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Thibaut VARÈNE [Tue, 16 Aug 2022 17:00:47 +0000 (19:00 +0200)]
build: always set CONFIG_IPV6
Disabling this build tunable breaks build and seems unrealistically
likely to be fixed.
This patch sets the related CONFIG to always true and removes the
config prompt, keeping the change minimal, and, should !CONFIG_IPV6 ever
be fixed, easy to revert.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Paul Spooren <mail@aparcar.org>
Acked-by: Josef.Schlehofer <pepe.schlehofer@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Sultan Alsawaf [Fri, 22 Jul 2022 06:36:31 +0000 (23:36 -0700)]
mac80211: parse the correct set of HE capabilities for AP mode
It is common for 802.11ax NICs to support more than just AP mode, which
results in there being a distinct set of HE capabilities for each mode. As
(bad) luck would have it, iw prints out info for each HE mode in sequential
order according to `enum nl80211_iftype`, and AP mode isn't always first.
As a result, the wrong set of HE capabilities can be parsed if an AP NIC
supports station (managed) mode or any other mode preceding AP mode, since
only the first set of HE capabilities printed by iw is parsed from awk's
output.
This has a noticeable impact on beamforming for example, since managed mode
usually doesn't have beamformer capabilities enabled, while AP mode does.
Hostapd won't be set up with the configs to enable beamformer capabilities
in this scenario, causing hostapd to disable beamforming to HE stations
even when it's supported by the AP.
Always parse the correct set of HE capabilities for AP mode to fix this.
This is achieved by trimming all of iw's output prior to the AP mode
capabilities, which ensures that the first set of HE capabilities are
always for AP mode.
Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
Markus Stockhausen [Fri, 19 Aug 2022 19:08:42 +0000 (21:08 +0200)]
realtek: more generic platform initialization
Platform startup still "guesses" the CPU clock speed by DT fixed values.
If possible take clock rates from a to be developed driver and align to
MIPS generic platfom initialization code. Pack old behaviour into a
fallback function. We might get rid of that some day.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Daniel Groth [Fri, 12 Aug 2022 18:11:54 +0000 (20:11 +0200)]
realtek: d-link: add support for dgs-1210-10mp
General hardware info:
-------------------------------------------------------------------------------
D-Link DGS-1210-10MP is a switch with 8 ethernet ports and 2 SFP ports, all
ports Gbit capable. It is based on a RTL8380 SoC @ 500MHz, DRAM 128MB and
32MB flash. All ethernet ports are 802.3af/at PoE capable
with a total PoE power budget of 130W.
File info:
-------------------------------------------------------------------------------
The dgs-1210-10mp is very similar to dgs-1210-10p so I used that as a start.
rtl838x.mk:
- Removed lua-rs232 package since it was a leftover from the old rtl83xx-poe
package.
- Updated the soc to 8380.
- Specified device variant: F.
- Installed the new realtek-poe package.
rtl8380_d-link_dgs-1210-10mp.dts:
- Moved dgs-1210 family common parts and non PoE related ports on rtl8231
to the new device tree dtsi files.
Serial connection:
-------------------------------------------------------------------------------
The UART for the SoC (115200 8N1) is available close to the front panel next
to the LED/key card connector via unpopulated standard 0.1" pin header
marked j4. Pin1 is marked with arrow and square.
Pin 1: Vcc 3,3V
Pin 2: Tx
Pin 3: Rx
Pin 4: Gnd
Installation with TFTP from u-boot
-------------------------------------------------------------------------------
I originally used the install procedure:
'OpenWrt installation using the TFTP method and serial console access' found
in the device wiki for the dgs-1210-16.
< https://openwrt.org/toh/d-link/dgs-1210-16_g1#openwrt_installation_using
_the_tftp_method_and_serial_console_access >
About the realtek-poe package
-------------------------------------------------------------------------------
The realtek-poe package is installed but there isn't any automatic PoE config
setting at this time so for now the PoE config must be edited manually.
Original OEM hardware/firmware data at first installation
-------------------------------------------------------------------------------
It has been installed, developed, and tested on a device with these OEM
hardware and firmware versions.
- U-boot: 2011.12.(2.1.5.67086)-Candidate1 (Jun 22 2020 - 15:03:58)
- Boot version: 1.01.001
- Firmware version: 6.20.007
- Hardware version: F1
Things to be done when support are developed
-------------------------------------------------------------------------------
- realtek-poe has been included in OpenWrt but the automatic config handling
has not been solved yet so in the future there will probably be some minor
updates for this device to handle the poe config.
- LED link_act and poe are per function supposed to be connected to the PoE
system.
But some software development is also needed to make this LED work and
shift the LED array between act and poe indication and to shift the mode
lights with mode key.
- LED poe_max should probably be used as straight forward error output from
the realtek-poe package error handling. But no code has been written for
this.
- SFP is currently not hot pluggable. Development is under progress to get
working I2C communication with SFP and have them hot pluggable.
When any device in the dgs-1210 family gets this working, I expect it
should be possible to implement the same solution in this device.
Signed-off-by: Daniel Groth <flygarn12@gmail.com>
[Capitalisation of abbreviations, DEVICE_VARIANT and update filenames,
device compatibles on single line]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Daniel Groth [Fri, 12 Aug 2022 18:10:20 +0000 (20:10 +0200)]
realtek: d-link: dgs-1210 remake of the device tree
I have collected the known information from the dts files we have.
After that I made a new device tree that should work for this whole D-Link
switch family.
This device tree is based on modules where you first select which SoC group
the device belongs to. Then you include the GPIO dtsi file depending on what
hardware your device has, see examples below.
This tree is also expandable for more hardware,
see the part 'Future expansion possibilities' further down.
-------------------------------------------------------------------------------
The device tree now looks like this:
----------------
| rtl838x.dtsi | // Note 1.
----------------
|
|
---------------------------------------
| rtl838x_d-link_dgs-1210_common.dtsi | // Note 2.
---------------------------------------
|
| --------------
|-------| device.dts | // Note 3.
| --------------
|
-------------------------------------
| rtl83xx_d-link_dgs-1210_gpio.dtsi | // Note 4.
-------------------------------------
|
| --------------
|-------| device.dts | // Note 5.
--------------
Note 1; Included in rtl838x_d-link_dgs-1210_common.dtsi.
Note 2; SoC level information and memory mapping. Choose which one to include
in the device dts.
Note 3; At this point dgs-1210-16 will come out here.
Note 4; In this dtsi only common board hardware based on the rtl8231 is found.
No PoE based hardware in this dtsi.
In this dtsi there is no <#include> to above *_common.dtsi.
Note 5; Device dts with only rtl8231 based hardware without PoE will come out
here.
-------------------------------------------------------------------------------
How to set up in dts file:
The device dts will have one of these two <#include> alternatives.
This alternative includes only common features:
<#include "rtl838x_d-link_dgs-1210_common.dtsi">
This alternative includes common and the rtl8231 GPIO (no PoE) features:
<#include "rtl838x_d-link_dgs-1210_common.dtsi">
<#include "rtl83xx_d-link_dgs-1210_gpio.dtsi">
-------------------------------------------------------------------------------
Implementation:
Finally, I also implemented this new family device tree on the current
supported devices:
dgs-1210-10p
dgs-1210-16
dgs-1210-20
dgs-1210-28
The implementation for the dgs-1210-10p is different. I have removed the
information from the rtl8382_d-link_dgs-1210-10p.dts that is already present
in rtl838x_d-link_dgs-1210_common.dtsi.
Since the rest isn't officially probed in the device dts I do not want to
include the rtl83xx_d-link_dgs-1210_gpio.dtsi with dgs-1210-10p.dts.
Since I don't have these devices to test on I have built the original firmware
for each one of these devices before this change and saved the dtb file and
then compared the original dtb file with the dtb file built with this new
device tree.
-------------------------------------------------------------------------------
Future expansion possibilities:
In parallel with the rtl838x_d-link_dgs-1210_common.dtsi in the tree map
we can make a rtl839x_d-link_dgs-1210_common.dtsi to use the rtl839x.dtsi if
the need arises with more devices based on rtl839x soc.
When we have more PoE devices so the hardware map for these gets more clear
we can make a rtl83xx_d-link_dgs-1210_poe.dtsi below
the rtl83xx_d-link_dgs-1210_gpio.dtsi in the tree map.
I looked at the port and switch setup to see if it could be moved to the dtsi.
I decided not to touch this part now. The reason was that there isn't really
any meaningful way this could be shared between the devices.
The only thing in common over the family is the 8+2sfp ports on the
dgs-1210-10xx device.
And then there is the hot plug SFP and I2C ports that aren’t implemented
on any device. So maybe when we see the whole port map for the family
then maybe the ports can be moved to a *_common.dtsi but I don't think it is
the right moment for that now.
Signed-off-by: Daniel Groth <flygarn12@gmail.com>
[Capitalisation of abbreviations and 'D-Link']
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Nick French [Sat, 13 Aug 2022 15:23:58 +0000 (10:23 -0500)]
uencrypt: support all available ciphers
Modify uencrypt to support any cipher provided by ssl library.
Original tool supported only AES-128-CBC to decrypt the config
mtd of Arcadyan WG430223/WG443223.
TP-Link Deco S4 has mtd configuration encrypted with DES-ECB,
so make the cipher generic to support both routers.
Signed-off-by: Nick French <nickfrench@gmail.com>
Reviewed-by: Eneas U de Queiroz >cotequeiroz@gmail.com>
Mikhail Zhilkin [Sat, 9 Jul 2022 17:09:57 +0000 (17:09 +0000)]
ramips: get MAC addr from the encrypted partition (WG4хх223)
This commit resolves #10062. Adds decryption of the Arcadyan WG4xx223
configuration partition (board_data)to get base MAC address from it.
As a result, after this change the hack with saving MAC addressees to
u-boot-env before installation of OpenWrt is no longer necessary.
This is necessary for the following devices:
- Beeline Smartbox Flash (Arcadyan WG443223)
- MTS WG430223 (Arcadyan WG430223)
Example:
+----------------+-------------------+------------------------+
| | MTS WG430223 | Beeline Smartbox Flash |
+----------------+-------------------+------------------------+
| base mac (mtd) | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06 |
| label | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:09 |
| LAN | A4:xx:xx:51:xx:F6 | 30:xx:xx:51:xx:09 |
| WAN | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06 |
| WLAN_2g | A4:xx:xx:51:xx:F5 | 30:xx:xx:51:xx:07 |
| WLAN_5g | A6:xx:xx:21:xx:F5 | 32:xx:xx:41:xx:07 |
+----------------+-------------------+------------------------+
Collected statistic shows that the 2-4th bits of the 7th byte of the
WLAN_5g MAC are the constant (see #10062 for more details):
- Beeline Smartbox Flash - 100
- MTS WG430223 - 010
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Mikhail Zhilkin [Tue, 12 Jul 2022 14:52:04 +0000 (14:52 +0000)]
base-files: add mtd_get_mac_encrypted_arcadyan function
Some Arcadyan devices (e.g. MTS WG430223) keep their config in encrypted
mtd. This adds mtd_get_mac_encrypted_arcadyan() function to get the MAC
address from the encrypted partition. Function uses uencrypt utility for
decryption (and openssl if the uencrypt wasn't found).
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
David Bauer [Thu, 18 Aug 2022 16:02:48 +0000 (18:02 +0200)]
ramips: fix ZyXEL NWA55AXE model name
The model name was missing a letter.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hauke Mehrtens [Tue, 16 Aug 2022 21:38:52 +0000 (23:38 +0200)]
iproute2: Fix KERNEL_INCLUDE in SDK
In the SDK the folder $(LINUX_DIR)/user_headers/include does not exist,
but it more or less contains the same content as
$(LINUX_DIR)/include/uapi which also exists in the SDK.
Since iproute2 commit
1d819dcc741e ("configure: fix parsing issue on
include_dir option") it checks if this folder exists and aborts the
build if it does not exists.
https://git.kernel.org/pub/scm/network/iproute2/iproute2.git/commit/?id=
1d819dcc741e25958190e31f8186c940713fa0a8
With this commit the KERNEL_INCLUDE variable points to a valid folder
with the kernel include headers. I am not sure if they are actually
needed because the build worked before even with an invalid path.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rafał Miłecki [Wed, 17 Aug 2022 20:45:11 +0000 (22:45 +0200)]
bcm4908: enable NVMEM U-Boot env data driver
It's needed for devices with U-Boot bootloader.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Wed, 17 Aug 2022 20:40:30 +0000 (22:40 +0200)]
kernel: add CONFIG_NVMEM_U_BOOT_ENV symbol to configs
This fixes:
U-Boot environment variables support (NVMEM_U_BOOT_ENV) [N/m/y/?] (NEW)
Fixes: 34cf310435044 ("kernel: backport U-Boot environment data NVMEM driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Wed, 17 Aug 2022 18:44:52 +0000 (20:44 +0200)]
kernel: backport U-Boot environment data NVMEM driver
It parses U-Boot env data into NVMEM cells.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Wed, 17 Aug 2022 09:04:29 +0000 (11:04 +0200)]
kernel: rename 5.20 patches to 6.0
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Josef Schlehofer [Tue, 26 Jul 2022 12:32:37 +0000 (14:32 +0200)]
mvebu: leds: Turris Omnia improvements
It backports this patch series, which is currently on review:
https://lore.kernel.org/linux-leds/
20220704105955.15474-1-kabel@kernel.org/T/#rb89a4ca5a836f17bdcc53d65549e0b1779bb6a18
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Josef Schlehofer [Tue, 26 Jul 2022 12:31:26 +0000 (14:31 +0200)]
mvebu: backport pending DTS changes for Turris Omnia
Backport pending patches:
- https://lore.kernel.org/linux-arm-kernel/
20220704113622.18887-1-kabel@kernel.org/
- https://lore.kernel.org/linux-arm-kernel/
20220704113622.18887-2-kabel@kernel.org/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Rui Salvaterra [Sun, 10 Apr 2022 20:29:08 +0000 (21:29 +0100)]
mvebu: refresh the 5.15 kconfigs
Clean them up.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Rui Salvaterra [Mon, 4 Apr 2022 15:06:16 +0000 (16:06 +0100)]
mvebu: add Linux 5.15 as testing kernel
Run-tested on the cortexa9 subtarget (Turris Omnia).
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Rui Salvaterra [Mon, 4 Apr 2022 14:58:47 +0000 (15:58 +0100)]
mvebu: update the kconfigs for 5.15
And remove irrelevant stuff while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Rui Salvaterra [Mon, 4 Apr 2022 14:54:26 +0000 (15:54 +0100)]
mvebu: copy 5.10 kconfigs to 5.15
Will be refreshed/updated later.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Rui Salvaterra [Sun, 10 Apr 2022 11:42:32 +0000 (12:42 +0100)]
mvebu: refresh 5.15 patches
Deleted (upstreamed):
303-linksys_hardcode_nand_ecc_settings.patch [1]
Deleted (not needed):
314-arm64-dts-uDPU-switch-PHY-operation-mode-to-2500base.patch [2]
Manually rebased:
700-mvneta-tx-queue-workaround.patch
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=
4daff3e5b42422cd4af758cc7768223d2b7f6e14
[2] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=
7f73acade0cde61341cb77e0dc74de51ac059d4f
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Rui Salvaterra [Mon, 4 Apr 2022 14:49:30 +0000 (15:49 +0100)]
mvebu: remove all ≤ 5.15-tagged patches
They're already upstream.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Rui Salvaterra [Mon, 4 Apr 2022 14:47:03 +0000 (15:47 +0100)]
mvebu: copy 5.10 patches to 5.15
Linux 5.15 on Marvell EBU, here we go!
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Hauke Mehrtens [Sat, 6 Aug 2022 23:09:42 +0000 (01:09 +0200)]
toolchain: glibc: Increase min kernel version to 5.10
This removes all compatibility code normally compiled into glibc for
kernel < 5.10 from our build. The build glibc version will only work
with Linux kernel >= 5.10.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 6 Aug 2022 21:56:38 +0000 (23:56 +0200)]
toolchain: glibc: Update to glibc 2.35
This updates to glibc to version 2.35.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Stijn Tintel [Thu, 11 Aug 2022 09:46:23 +0000 (12:46 +0300)]
hostapd: add mbo flag to get_clients ubus method
There is no WLAN_STA_MBO flag, but according to the hostapd source code,
when an STA does not support MBO, cell_capa will be 0. Use this to
indicate MBO support in the get_clients ubus method.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: David Bauer <mail@david-bauer.net>
Stijn Tintel [Thu, 21 Jul 2022 16:26:56 +0000 (18:26 +0200)]
kernel: extract kmod-sched-act-ipt from kmod-sched
There is only one module in kmod-sched that depends on iptables. Move it
to its own kmod package so we can drop the kmod-ipt-core dependency from
kmod-sched. This makes it possible to disable all kmod-ipt-* packages
without having to disable kmod-sched. Since we now default to firewall4
and nftables, we should avoid iptables dependencies where we can.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Hauke Mehrtens [Sun, 14 Aug 2022 21:36:58 +0000 (23:36 +0200)]
Revert "binutils: update to 2.39"
This reverts commit
cc24c4ed5eae66c061e5787bb172fd2a91861f25.
binutils does not compile with glibc:
Package binutils is missing dependencies for the following libraries:
libgprofng.so.0
libmsgpackc.so.2
libstdc++.so.6
libbpf does not compile against binutils 2.39 any more, see:
https://github.com/libbpf/bpftool/issues/30
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 13 Aug 2022 12:21:00 +0000 (14:21 +0200)]
fstools: update to git HEAD
8c213b0 libfstools: Rename move_mount() function to ovl_move_mount() for glibc 2.36
81785c1 block: Do not include linux/fs.h any more
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 6 Aug 2022 21:12:56 +0000 (23:12 +0200)]
toolchain: Update glibc 2.34 to recent HEAD
This adds the following changes:
71326f1f2f nptl: Fix pthread_cancel cancelhandling atomic operations
3e0a91b79b scripts: Add glibcelf.py module
f0c71b34f9 Default to --with-default-link=no (bug 25812)
ca0faa140f misc: Fix rare fortify crash on wchar funcs. [BZ 29030]
0d477e92c4 INSTALL: Rephrase -with-default-link documentation
bc56ab1f4a dlfcn: Do not use rtld_active () to determine ld.so state (bug 29078)
83cc145830 scripts/glibcelf.py: Mark as UNSUPPORTED on Python 3.5 and earlier
16245986fb x86-64: Optimize load of all bits set into ZMM register [BZ #28252]
b5a44a6a47 x86: Modify ENTRY in sysdep.h so that p2align can be specified
5ec3416853 x86: Optimize memcmp-evex-movbe.S for frontend behavior and size
6d18a93dbb x86: Optimize memset-vec-unaligned-erms.S
baf3ece634 x86: Replace sse2 instructions with avx in memcmp-evex-movbe.S
f35ad30da4 x86-64: Improve EVEX strcmp with masked load
a182bb7a39 x86-64: Remove Prefer_AVX2_STRCMP
2e64237a87 x86-64: Replace movzx with movzbl
a7392db2ff x86: Optimize memmove-vec-unaligned-erms.S
cecbac5212 x86: Double size of ERMS rep_movsb_threshold in dl-cacheinfo.h
7cb126e7e7 x86: Shrink memcmp-sse4.S code size
4bbd0f866a x86-64: Use notl in EVEX strcmp [BZ #28646]
f3a99b2216 x86: Don't set Prefer_No_AVX512 for processors with AVX512 and AVX-VNNI
c796418d00 x86: Optimize L(less_vec) case in memcmp-evex-movbe.S
9681691402 linux: Fix missing internal 64 bit time_t stat usage
55640ed3fd i386: Regenerate ulps
88a8637cb4 linux: Fix fchmodat with AT_SYMLINK_NOFOLLOW for 64 bit time_t (BZ#29097)
c66c92181d posix/glob.c: update from gnulib
bc6fba3c80 Add PF_MCTP, AF_MCTP from Linux 5.15 to bits/socket.h
fd5dbfd1cd Update kernel version to 5.15 in tst-mman-consts.py
5146b73d72 Add ARPHRD_CAN, ARPHRD_MCTP to net/if_arp.h
6af165658d Update syscall lists for Linux 5.17
81181ba5d9 Update kernel version to 5.16 in tst-mman-consts.py
0499c3a95f Update kernel version to 5.17 in tst-mman-consts.py
f858bc3093 Add SOL_MPTCP, SOL_MCTP from Linux 5.16 to bits/socket.h
c108e87026 aarch64: Add HWCAP2_ECV from Linux 5.16
97cb8227b8 Add HWCAP2_AFP, HWCAP2_RPRES from Linux 5.17 to AArch64 bits/hwcap.h
31af92b9c8 manual: Clarify that abbreviations of long options are allowed
0d5b36c8cc x86: Optimize strcmp-avx2.S
c41a66767d x86: Optimize strcmp-evex.S
d299032743 x86-64: Fix strcmp-avx2.S
53ddafe917 x86-64: Fix strcmp-evex.S
ea19c490a3 x86: Improve vec generation in memset-vec-unaligned-erms.S
190ea5f7e4 x86: Remove SSSE3 instruction for broadcast in memset.S (SSE2 Only)
5cb6329652 x86-64: Optimize bzero
70509f9b48 x86: Set .text section in memset-vec-unaligned-erms
5373c90f2e x86: Fix bug in strncmp-evex and strncmp-avx2 [BZ #28895]
e123f08ad5 x86: Fix fallback for wcsncmp_avx2 in strcmp-avx2.S [BZ #28896]
e4a2fb76ef manual: Document the dlinfo function
91c2e6c3db dlfcn: Implement the RTLD_DI_PHDR request type for dlinfo
b72bbba236 fortify: Ensure that __glibc_fortify condition is a constant [BZ #29141]
8de6e4a199 x86: Improve L to support L(XXX_SYMBOL (YYY, ZZZ))
6cba46c858 x86_64/multiarch: Sort sysdep_routines and put one entry per line
37f373e334 x86-64: Remove bzero weak alias in SS2 memset
dd457606ca x86_64: Remove bcopy optimizations
3c55c20756 x86: Code cleanup in strchr-avx2 and comment justifying branch
dd6d3a0bbc x86: Code cleanup in strchr-evex and comment justifying branch
0ae1006967 x86: Optimize strcspn and strpbrk in strcspn-c.c
0a2da01110 x86: Optimize strspn in strspn-c.c
0dafa75e3c x86: Remove strcspn-sse2.S and use the generic implementation
3811544655 x86: Remove strpbrk-sse2.S and use the generic implementation
a4b1cae068 x86: Remove strspn-sse2.S and use the generic implementation
5997011826 x86: Optimize str{n}casecmp TOLOWER logic in strcmp.S
3605c74407 x86: Optimize str{n}casecmp TOLOWER logic in strcmp-sse42.S
3051cf3e74 x86: Add AVX2 optimized str{n}casecmp
b13a2e68eb x86: Add EVEX optimized str{n}casecmp
80883f4354 x86: Remove AVX str{n}casecmp
4ff6ae069b x86: Small improvements for wcslen
ffe75982cc x86: Remove memcmp-sse4.S
df5de87260 x86: Cleanup page cross code in memcmp-avx2-movbe.S
0a11305416 x86: Optimize {str|wcs}rchr-sse2
00f09a14d2 x86: Optimize {str|wcs}rchr-avx2
596c9a32cc x86: Optimize {str|wcs}rchr-evex
1f83d40dfa elf: Remove unused NEED_DL_BASE_ADDR and _dl_base_addr
b0bd6a1323 elf: Merge dl-sysdep.c into the Linux version
2139b1848e Linux: Remove HAVE_AUX_SECURE, HAVE_AUX_XID, HAVE_AUX_PAGESIZE
458733fffe Linux: Remove DL_FIND_ARG_COMPONENTS
08728256fa Linux: Assume that NEED_DL_SYSINFO_DSO is always defined
4b9cd5465d Linux: Consolidate auxiliary vector parsing
1cc4ddfeeb Revert "Linux: Consolidate auxiliary vector parsing"
28bdb03b1b Linux: Include <dl-auxv.h> in dl-sysdep.c only for SHARED
ff900fad89 Linux: Consolidate auxiliary vector parsing (redo)
be9240c84c elf: Remove __libc_init_secure
1e7b011f87 i386: Remove OPTIMIZE_FOR_GCC_5 from Linux libc-do-syscall.S
1a5b9d1a23 i386: Honor I386_USE_SYSENTER for 6-argument Linux system calls
b38c9cdb58 Linux: Define MMAP_CALL_INTERNAL
b2387bea84 ia64: Always define IA64_USE_NEW_STUB as a flag macro
e7ca2a475c Linux: Implement a useful version of _startup_fatal
43d77ef9b8 Linux: Introduce __brk_call for invoking the brk system call
ede8d94d15 csu: Implement and use _dl_early_allocate during static startup
89b638f48a S390: Enable static PIE
c73c79af7d rtld: Use generic argv adjustment in ld.so [BZ #23293]
b2585cae28 linux: Add a getauxval test [BZ #23293]
14770f3e04 string.h: fix __fortified_attr_access macro call [BZ #29162]
83ae8287c1 x86: Fallback {str|wcs}cmp RTM in the ncmp overflow case [BZ #29127]
ff450cdbde Fix deadlock when pthread_atfork handler calls pthread_atfork or dlclose
b349fe0722 misc: Use 64 bit stat for daemon (BZ# 29203)
aa8a87f51d misc: Use 64 bit stat for getusershell (BZ# 29204)
9db6a597ef posix: Use 64 bit stat for posix_fallocate fallback (BZ# 29207)
f9c3e57ac2 posix: Use 64 bit stat for fpathconf (_PC_ASYNC_IO) (BZ# 29208)
61fd3e0e74 socket: Use 64 bit stat for isfdtype (BZ# 29209)
34422108f4 inet: Use 64 bit stat for ruserpass (BZ# 29210)
52431199b5 catgets: Use 64 bit stat for __open_catalog (BZ# 29211)
b3f935940e iconv: Use 64 bit stat for gconv_parseconfdir (BZ# 29213)
9947f2df19 socket: Fix mistyped define statement in socket/sys/socket.h (BZ #29225)
4c92a10412 powerpc: Fix VSX register number on __strncpy_power9 [BZ #29197]
a7ec6363a3 nptl: Fix __libc_cleanup_pop_restore asynchronous restore (BZ#29214)
96944f0f81 hppa: Remove _dl_skip_args usage (BZ# 29165)
bb4148283f nios2: Remove _dl_skip_args usage (BZ# 29187)
368c5c3e00 nss: add assert to DB_LOOKUP_FCT (BZ #28752)
94ab2088c3 nss: handle stat failure in check_reload_and_get (BZ #28752)
4b246b2bbd linux: Fix mq_timereceive check for 32 bit fallback code (BZ 29304)
7789a84923 nptl: Fix ___pthread_unregister_cancel_restore asynchronous restore
8d324019e6 x86_64: Remove end of line trailing spaces
eb9aa96fac x86_64: Remove bzero optimization
8ab861d295 x86_64: Implement evex512 version of strlen, strnlen, wcslen and wcsnlen
f6bc52f080 x86-64: Ignore r_addend for R_X86_64_GLOB_DAT/R_X86_64_JUMP_SLOT
82a707aeb7 x86_64: Add strstr function with 512-bit EVEX
70be93d1c5 x86: Create header for VEC classes in x86 strings library
e805606193 x86: Add COND_VZEROUPPER that can replace vzeroupper if no `ret`
4901009dad x86: Optimize memrchr-sse2.S
83a986e9fb x86: Optimize memrchr-evex.S
b05bd59823 x86: Optimize memrchr-avx2.S
a910d7e164 x86: Shrink code size of memchr-avx2.S
3c87383a20 x86: Shrink code size of memchr-evex.S
820504e3ed x86: ZERO_UPPER_VEC_REGISTERS_RETURN_XTEST expect no transactions
fc54e1fae8 x86: Align varshift table to 32-bytes
6e008c884d x86: Fix misordered logic for setting `rep_movsb_stop_threshold`
9d50e162ee x86: Add sse42 implementation to strcmp's ifunc
94b0dc9419 x86: Add bounds `x86_non_temporal_threshold`
ba1c3f23d9 x86: Cleanup bounds checking in large memcpy case
c51d8d383c x86: Add BMI1/BMI2 checks for ISA_V3 check
d201c59177 x86: Align entry for memrchr to 64-bytes.
aadd0a1c7c x86: Put wcs{n}len-sse4.1 in the sse4.1 text section
f4598f0351 x86: Add definition for __wmemset_chk AVX2 RTM in ifunc impl list
7079931c51 x86: Move and slightly improve memset_erms
35f9c72c8b x86: Move mem{p}{mov|cpy}_{chk_}erms to its own file
ccc54bd61c x86: Add missing IS_IN (libc) check to strncmp-sse4_2.S
b991af5063 Update syscall-names.list for Linux 5.18
b2f32e7464 malloc: Simplify implementation of __malloc_assert
875b2414cd dlfcn: Pass caller pointer to static dlopen implementation (bug 29446)
4ab59ce4e5 Update syscall lists for Linux 5.19
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 13 Aug 2022 19:44:24 +0000 (21:44 +0200)]
kernel: kmod-hwmon-tps23861: Add missing dependency to kmod-regmap-i2c
This fixes the following build error:
Package kmod-hwmon-tps23861 is missing dependencies for the following libraries:
regmap-i2c.ko
Fixes: b664646db74a ("kernel: add kmod-hwmon-tps23861 support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Oscar Molnar [Sat, 6 Aug 2022 15:13:41 +0000 (16:13 +0100)]
build: add support for python3.11 and higher
python3.11 beta is out but fails to run the makefile currently
this supports python versions from 3.6 to 3.99 with the python3 binary
it also checks specifically for 3.11 as it is the latest version out
Signed-off-by: Oscar Molnar <oscar@tymscar.com>
Tomas Lara [Sun, 7 Aug 2022 00:13:07 +0000 (20:13 -0400)]
kernel: remove CONFIG_MMC_BLOCK_BOUNCE
CONFIG_MMC_BLOCK_BOUNCE was removed in kernel v4.13-rc1
https://github.com/torvalds/linux/commit/
c3dccb74be28a345a2ebcc224e41b774529b8b8f
Signed-off-by: Tomas Lara <tl849670@gmail.com>
Hauke Mehrtens [Sat, 13 Aug 2022 17:01:15 +0000 (19:01 +0200)]
umbim: bump to git HEAD
146bc77 umbim: fix invalid mbim message string encoding
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 13 Aug 2022 16:56:58 +0000 (18:56 +0200)]
ubox: update to latest git HEAD
fa6cb9a kmodloader: fix bad realloc usage
4c7b720 kmodloader: fix GCC fanalyzer warnings
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 13 Aug 2022 16:35:46 +0000 (18:35 +0200)]
iwinfo: update to latest HEAD
705d3b5 iwinfo: Add missing auth_suites mappings for WPA3
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Nick Hainke [Sun, 7 Aug 2022 21:26:05 +0000 (23:26 +0200)]
toolchain: binutils: add support for version 2.39
Release notes:
https://sourceware.org/pipermail/binutils/2022-August/122246.html
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sun, 7 Aug 2022 21:09:41 +0000 (23:09 +0200)]
binutils: update to 2.39
Changes:
* The ELF linker will now generate a warning message if the stack is made
executable. Similarly it will warn if the output binary contains a
segment with all three of the read, write and execute permission
bits set. These warnings are intended to help developers identify
programs which might be vulnerable to attack via these executable
memory regions.
The warnings are enabled by default but can be disabled via a command
line option. It is also possible to build a linker with the warnings
disabled, should that be necessary.
* The ELF linker now supports a --package-metadata option that allows
embedding a JSON payload in accordance to the Package Metadata
specification.
* In linker scripts it is now possible to use TYPE=<type> in an output
section description to set the section type value.
* The objdump program now supports coloured/colored syntax
highlighting of its disassembler output for some architectures.
(Currently: AVR, RiscV, s390, x86, x86_64).
* The nm program now supports a --no-weak/-W option to make it ignore
weak symbols.
* The readelf and objdump programs now support a -wE option to prevent
them from attempting to access debuginfod servers when following
links.
* The objcopy program's --weaken, --weaken-symbol, and
--weaken-symbols options now works with unique symbols as well.
Announcement:
https://sourceware.org/pipermail/binutils/2022-August/122246.html
Signed-off-by: Nick Hainke <vincent@systemli.org>
projects / openwrt / staging / ansuel.git / log