Kyle Hendry [Sun, 17 Nov 2024 02:16:31 +0000 (18:16 -0800)]
bmips: dts: fix pinctrl error
The kernel logs the error "bcm6368_nand
10000200.nand: there is not valid
maps for state default" on boot and all nand pins show as UNCLAIMED in
sysfs pinmux-pins.
bcm6362.dtsi, bcm6368.dtsi and bcm63268.dtsi use the undocumented property
group which the driver doesn't understand. This has been documented upstream
in commit
caf963efd4b0b9ff42ca12e52b8efe277264d35b.
Replacing group with pins allows the nand pins to be properly configured.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[add bcm636/bcm6368 and fix commit title]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sander Vanheule [Tue, 24 Dec 2024 08:56:11 +0000 (09:56 +0100)]
realtek: generate compat_version 2.0 for GS1900
The GS1900 images have been updated to have a larger firmware partition,
bumping the compatibility version to 2.0. However, since this version is
generated on first boot and the default was used, these images still
advertised 1.0 after a fresh install.
Add a new uci-defaults script that will generate the correct version for
all affected Zyxel GS1900 devices.
Fixes: 35acdbe9095d ("realtek: merge Zyxel GS1900 firmware partitions")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Rosen Penev [Mon, 7 Oct 2024 00:08:24 +0000 (17:08 -0700)]
kernel:
leds-gca230718: remove _remove
Not needed. Everything can be replaced with devm.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16869
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Mon, 7 Oct 2024 00:02:27 +0000 (17:02 -0700)]
kernel:
leds-gca230718: use shorter priv variable
Shorter and more consistent with other drivers.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16869
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Sun, 6 Oct 2024 23:56:25 +0000 (16:56 -0700)]
kernel:
leds-gca230718: remove status variable
I have no idea why this is even here. Simplifies the code with direct
returns.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16869
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Sun, 6 Oct 2024 23:53:39 +0000 (16:53 -0700)]
kernel:
leds-gca230718: remove old kernel compat
Not needed as all the older kernels are gone.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16869
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Sun, 6 Oct 2024 23:51:49 +0000 (16:51 -0700)]
kernel:
leds-gca230718: run through clang-format
This file does not use a coding style consistent with the kernel. Run
clang-format with the kernel's .clang-format file.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16869
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Mon, 16 Dec 2024 23:42:19 +0000 (15:42 -0800)]
lantiq: use nvmem for fritz 736x
Two use AR9287 and one AR9381. Both have different calibration sizes.
Move differences out of wifi node to make it clearer what's what.
qca,no-eeprom needs to stay for 7362sl as there's no nvmem equivalent
for caldata_extract_reverse
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Mon, 16 Dec 2024 23:07:50 +0000 (15:07 -0800)]
lantiq: use nvmem for fritz73x0
These units use AR9287, which has a calibration size of 3d8.
Also fixed compatible string to the proper one to indicate AR9287.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Mon, 16 Dec 2024 07:54:02 +0000 (23:54 -0800)]
bmips: dsl-2750b-b1: fix calibration size
AR9287 uses 3d8, not 440 like newer chips.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Sat, 14 Dec 2024 22:32:14 +0000 (14:32 -0800)]
ath79: wr2543: add compatible string for wifi
Makes it clear that the calibration size is correct as most ar72xx
devices use older wifi chips.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Mon, 16 Dec 2024 22:15:08 +0000 (14:15 -0800)]
ath79: fix calibration size for AR9287
These devices use AR9287, which uses 3d8 as the calibration size, not
440 like newer chips do. Add a compatible line to make it clear that
this is the case.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Sun, 15 Dec 2024 01:07:36 +0000 (17:07 -0800)]
ath79: use nvmem for wrong 3e0 cal size
These three devices use AR9287 chips, which have a calibration size of 3d8.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Joel Low [Sat, 14 Dec 2024 13:39:36 +0000 (21:39 +0800)]
netfilter: add kmod-nfnetlink-ct{helper,timeout}
Add kmod-nfnetlink-ct{helper,timeout} to allow handling firewall rules
in userspace (together with conntrackd). The timeout module allows
specifying custom expiration rules.
Signed-off-by: Joel Low <joel@joelsplace.sg>
Link: https://github.com/openwrt/openwrt/pull/17267
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Roland Reinl [Fri, 13 Dec 2024 17:58:26 +0000 (18:58 +0100)]
mediatek: filogic: Add support for D-Link AQUILA PRO AI M60
Specification:
- MT7986 CPU using 2.4GHz and 5GHz WiFi (both AX)
- MT7531 switch
- 512MB RAM
- 128MB NAND flash (MX35LF1GE4AB-Z4I) with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718 (Same as D-Link M30 A1)
- 3 buttons (WPS, reset, LED on/off)
- 1x 2.5 Gbit WAN port with Maxlinear GPY211C
- 4x 1 Gbit LAN ports
Disassembly:
- There are five screws at the bottom: 2 under the rubber feet, 3 under the label.
- After removing the screws, the white plastic part can be shifted out of the blue part.
- Be careful because the antennas are mounted on the side and the top of the white part.
Serial Interface
- The serial interface can be connected to the 4 pin holes next to/under the antenna cables.
- Note that there is another set of 4 pin holes on the side of the board, it's not used.
- Pins (from front to rear):
- 3.3V (do not connect)
- TX
- RX
- GND
- Settings: 115200, 8N1
MAC addresses:
- MAC address is stored in partition "Odm" at offset 0x81 (for example XX:XX:XX:XX:XX:52)
- MAC address on the device label is ODM + 1 (for example XX:XX:XX:XX:XX:53)
- WAN MAC is the one from the ODM partition (for example XX:XX:XX:XX:XX:52)
- LAN MAC is the one from the ODM partition + 1 (for example XX:XX:XX:XX:XX:53)
- WLAN MAC (2.4 GHz) is the one from the ODM partition + 2 (for example (XX:XX:XX:XX:XX:54)
- WLAN MAC (5 GHz) is the one from the ODM partition + 5 (for example (XX:XX:XX:XX:XX:57)
Flashing via OEM web interface:
- Currently not supported because image crypto is not known
Flashing via recovery web interface:
- This is only working if the first partition is active because recovery images are always flashed to the active partition and OpenWrt can only be executed from the first partition
- Use a Chromium based browser, otherwise firmware upgrade might not work
- Recovery web interface is accessible via 192.168.200.1 after keeping the reset button pressed during start of the device until the LED blinks red
- Upload the recovery image, this will take some time. LED will continue flashing red during the update process
- The after flashing, the recovery web interface redirects to http://192.168.0.1. This can be ignored. OpenWrt is accessible via 192.168.1.1 after flashing
- If the first partition isn't the active partition, OpenWrt will hang during the boot process. In this case:
- Download the recovery image from https://github.com/RolandoMagico/openwrt/releases/tag/M60-Recovery-UBI-Switch (UBI switch image)
- Enable recovery web interface again and load the UBI switch image. This image works on the second partition of the M60
- OpenWrt should boot now as expected. After booting, flash the normal OpenWrt sysupgrade image (for example in the OpenWrt web interface)
- Flashing a sysupgrade image from the UBI switch image will make the first partition the active partition and from now on, default OpenWrt images can be used
Flashing via Initramfs:
- Before switching to OpenWrt, ensure that both partitions contain OEM firmware.
- This can be achieved by re-flashing the same OEM firmware version again via the OEM web interface.
- Flashing via OEM web interface will automatically flash the currently not active partition.
- Open router, connect serial interface
- Start a TFTP server at 192.168.200.2 and provide the initramfs image there
- When starting the router, select "7. Load Image" in U-Boot
- Settings for load address, load method can be kept as they are
- Specify host and router IP address if you use different ones than the default (Router 192.168.200.1, TFTP server 192.168.200.2)
- Enter the file name of the initramfs image
- Confirm "Run loaded data now?" question after loading the image with "Y"
- OpenWrt initramfs will start now
- Before flashing OpenWrt, create a backup of the "ubi" partition. It is required when reverting back to OEM
- Flash sysupgrade image to flash, during flashing the U-Boot variable sw_tryactive will be set to 0
- During next boot, U-Boot tries to boot from the ubi partition. If it fails, it will switch to the ubi1 partition
Reverting back to OEM:
- Boot the initramfs image as described in "Flashing via Initramfs" above
- Copy the backed up ubi partition to /tmp (e.g. by using SCP)
- Write the backup to the UBI partition: mtd write /tmp/OpenWrt.mtd4.ubi.bin /dev/mtd4
- Reboot the device, OEM firmware will start now
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17296
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Weijie Gao [Sun, 22 Dec 2024 10:32:54 +0000 (18:32 +0800)]
config: enable SECCOMP support for loongarch64
Make USE_SECCOMP selectable for loongarch64
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17335
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 22 Dec 2024 16:47:34 +0000 (17:47 +0100)]
procd: update to Git HEAD (2024-12-22)
42d3937 jail/seccomp: add support for loongarch64
Link: https://github.com/openwrt/openwrt/pull/17335
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Edward Chow [Tue, 10 Dec 2024 10:36:40 +0000 (18:36 +0800)]
ath79: port buffalo WZR-450HP2 from ar71xx
Referencing commit
a1837135e04b
Hardware
--------
SoC: Qualcomm Atheros QCA9558
RAM: 128M DDR2 (Nanya NT5TU64M16HG-AC)
FLASH: 128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN: QCA9558 3T3R 802.11 bgn
ETH: Qualcomm Atheros QCA8337
UART: 115200 8n1
BUTTON: Reset - WPS - "Router" switch
LED: 2x system-LED, 2x wlan-LED, 1x internet-LED,
2x routing-LED
LEDs besides the ethernet ports are controlled
by the ethernet switch
MAC Address:
use address(sample 1) source
label cc:e1:d5:xx:xx:ed art@macaddr_wan
lan cc:e1:d5:xx:xx:ec art@macaddr_lan
wan cc:e1:d5:xx:xx:ed $label
WiFi4_2G cc:e1:d5:xx:xx:ec art@cal_ath9k
Installation from Serial Console
------------
1. Connect to the serial console. Power up the device and interrupt
autoboot when prompted
2. Connect a TFTP server reachable at 192.168.11.10/24
to the ethernet port. Serve the OpenWrt initramfs image as
"openwrt.bin"
3. Boot the initramfs image using U-Boot
ath> tftpboot 0x84000000 openwrt.bin
ath> bootm 0x84000000
4. Copy the OpenWrt sysupgrade image to the device using scp and
install it like a normal upgrade (with no need to keeping config
since no config from "previous OpenWRT installation" could be kept
at all)
# sysupgrade -n /path/to/openwrt/sysupgrade.bin
Installation from Web Interface
------------
To flash just do a firmware upgrade from the stock firmware (Buffalo
branded dd-wrt) with squashfs-factory.bin
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/17227
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 22 Dec 2024 16:33:21 +0000 (17:33 +0100)]
mbedtls: Deactivate ARIA block cipher by default
The ARIA block cipher is pretty uncommon in TLS, deactivate it for now.
This saves some space and reduces the possible variations and attack
vectors of mbedtls.
ARIA support was deactivated in OpenWrt 23.05 by default.
Link: https://github.com/openwrt/openwrt/pull/17342
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tianling Shen [Mon, 23 Dec 2024 13:57:15 +0000 (21:57 +0800)]
uboot-rockchip: fix build with swig 4.3.0
Fixes the following error by backporting upstream update:
```
scripts/dtc/pylibfdt/libfdt_wrap.c: In function ‘_wrap_fdt_next_node’:
scripts/dtc/pylibfdt/libfdt_wrap.c:5581:17: error: too few arguments to function ‘SWIG_Python_AppendOutput’
5581 | resultobj = SWIG_Python_AppendOutput(resultobj, val);
| ^~~~~~~~~~~~~~~~~~~~~~~~
```
Fixes: https://github.com/openwrt/openwrt/issues/17345
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17352
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tianling Shen [Mon, 23 Dec 2024 13:56:31 +0000 (21:56 +0800)]
uboot-rockchip: increase rng-seed size
Increase rng-seed size to make Linux happy and initialize rng pool instantly.
Linux 5.19+ requires 32 bytes of entropy to initialize random pool, but u-boot
currently provides only 8 bytes.
Boot with 8 byte rng-seed (Linux 6.11):
# dmesg | grep crng
[ 12.089286] random: crng init done
Boot with 32 byte rng-seed (Linux 6.11):
# dmesg | grep crng
[ 0.000000] random: crng init done
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17352
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Shiji Yang [Sun, 22 Dec 2024 12:13:05 +0000 (20:13 +0800)]
Revert "ipq40xx: use PHY to control USB GPIO"
This reverts commit
3bd2cee9bf85f01732e05e0c8fb070fb18c74095.
Based on my testing, we are unable to control USB power supply
through some third-party tools (e.g. uhubctl) or sysfs in userspace.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17339
Signed-off-by: Robert Marko <robimarko@gmail.com>
Florian Maurer [Thu, 19 Dec 2024 10:49:13 +0000 (11:49 +0100)]
ipq40xx-generic: ws-ap3915i fix macadress
set macaddress correctly for board
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17305
Signed-off-by: Robert Marko <robimarko@gmail.com>
Florian Maurer [Thu, 19 Dec 2024 09:46:40 +0000 (10:46 +0100)]
ipq40xx-generic: EN WS-AP3915i remove BLOCKSIZE from image definition
The blocksize was too high, resulting in forgetting the config on sysupgrade
It is not needed for SPI-NOR.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17305
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hauke Mehrtens [Mon, 23 Dec 2024 00:49:04 +0000 (01:49 +0100)]
uboot-d1: Adapt BUILD_DEVICES to renamed boards
The boards where renamed, but BUILD_DEVICES was not adapted. This
variable points to the board name. Without this change the u-boot
binaries are not selected in the configuration.
Copy the u-boot binaries under the BUILD_DEVICES name as it is expected
by the image scripts.
Fixes: 33e23e8922ce ("build: d1: add SUPPORTED_DEVICES")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Thomas Richard [Fri, 29 Nov 2024 10:53:14 +0000 (11:53 +0100)]
arm-trusted-firmware-stm32: bump to v2.12
No need to pass the option no-warn-rwx-segments. Since v2.12, TF-A
automatically selects it if needed.
A patch is added to revert commit
03a581e2 ("feat(stm32mp1-fdts): remove
RTC clock configuration").
This commit removed RTC clock configuration, as it assumed that it was done
correctly by OPTEE.
But it is not the case. Without this patch the RTC is in a bad state,
consequently the wifi module cannot be initialized.
stm32_rtc
5c004000.rtc: rtc_ck is slow
stm32_rtc
5c004000.rtc: Can't enter in init mode. Prescaler config failed.
stm32_rtc: probe of
5c004000.rtc failed with error -110
sdio mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.st,stm32mp135f-dk.bin failed with error -2
brcmfmac: brcmf_sdio_htclk: HT Avail timeout (
1000000): clkctl 0x50
Tested on STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17243
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Thomas Richard [Fri, 29 Nov 2024 10:36:46 +0000 (11:36 +0100)]
include/trusted-firmware-a.mk: remove the no-warn-rwx-segments hack
Since v2.12, TF-A automatically selects the no-warn-rwx-segments option if
needed.
So move this hack to the package Makefiles.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17243
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Thomas Richard [Thu, 28 Nov 2024 17:05:29 +0000 (18:05 +0100)]
uboot-stm32: bump to 2024.10
Now the tool mkeficapsule is built by default if EFI_LOADER config is set
(which is the case by default for armv7).
This tool needs gnutls, which only exists in the packages feed.
As we don't need mkeficapsule, just disable it.
Tested on STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17243
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Thomas Richard [Thu, 28 Nov 2024 16:28:47 +0000 (17:28 +0100)]
optee-os-stm32: bump to 4.4.0
Tested on STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17243
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Sat, 15 Jun 2024 21:23:02 +0000 (14:23 -0700)]
ath79: nbg6x16: use nvmem
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16291
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 22 Dec 2024 15:41:11 +0000 (16:41 +0100)]
kernel: generic: netfilter: nft_set_hash: unaligned atomic read on struct nft_set_ext
Fix kernel panic on some 64 bit architectures.
This patch is pending upstream.
https://patchwork.ozlabs.org/project/netfilter-devel/patch/
20241222100239.336289-1-pablo@netfilter.org/
Fixes: https://github.com/openwrt/openwrt/issues/17336
Link: https://github.com/openwrt/openwrt/pull/17340
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Jianyu Zhuang [Tue, 10 Dec 2024 07:38:20 +0000 (15:38 +0800)]
mediatek: filogic: add support for Tenbay WR3000K
Tenbay WR3000K is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7981B.
- SoC: MetiaTek MT7981B
- RAM: Hynex H5TQ2G863GFR 512MiB
- Flash: Winbond W25N01GVZEIG 128MiB
- Wi-Fi: MediaTek MT7976C (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000)
- MediaTek MT7915E: 2.4GHz and 5GHz
- Ethernet: 1x 10/100/1000 Mbps WAN + 3x 10/100/1000 Mbps LAN
- Switch: MediaTek MT7531AE
- UART: J4 (115200 baud)
- LEDs: Power
- Buttons: Reset, WPS
- PWR: 12V/1A DC, 5.5×2.1 connector
| Vendor | OpenWrt Interface | Address | Notes |
|---------|-------------------|---------------|------------------------------------------------|
| WAN | wan | Label MAC | Stored MAC in factory + offset 4, label MAC is Stored MAC - 2 |
| LAN | br-lan | Label MAC+1 | |
| 2.4GHz | phy0-ap0 | Label MAC + 2 | |
| 5GHz | phy1-ap0 | Label MAC + 3 | |
- 0x000000000000-0x000000100000 : "BL2"
- 0x000000100000-0x000000180000 : "u-boot-env"
- 0x000000180000-0x000000380000 : "Factory"
- 0x000000380000-0x000000580000 : "FIP"
- 0x000000580000-0x000003580000 : "ubi"
- 0x000003580000-0x000006580000 : "ubi1"
- 0x000006580000-0x0000065a0000 : "Product"
- 0x0000065a0000-0x000007580000 : "Custom"
- The original partition-Ubi partition-Ubi1 is an AB dual system, and Openwrt only uses Ubi. So flash requires modifying the uboot variable `boot_from=ubi` to ensure that it only starts from Ubi.
- The Product and Custom partitions are original and only exist to align with the original layout; they are not used by OpenWrt.
- id: 0, kernel
- id: 1, rootfs
- id: 2, rootfs_data
- **USB-to-TTL Serial Adapter** (e.g., CH340 or CP2102).
- **Dupont Wires** (male-to-male, 3 wires).
- **PC/Laptop** with a serial communication tool.
- Screwdriver (to open the router case).
1. **OpenWrt Firmware**:
- Download the appropriate `wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin` firmware file for your router from the [OpenWrt website](https://openwrt.org/).
2. **Serial Communication Tool**:
- Windows: PuTTY, Tera Term.
- Linux/Mac: Minicom, screen.
3. (Optional) **TFTP Server**:
- Install a TFTP server like Tftpd64 or tftp-hpa.
---
1. Open the router casing and locate the **TX, RX, and GND** pins.
2. Connect the router pins to the USB-to-TTL adapter as follows:
- **TX (router)** → **RX (adapter)**
- **RX (router)** → **TX (adapter)**
- **GND (router)** → **GND (adapter)**
3. Do **not** connect the VCC pin to avoid damage.
- **Baud rate**: 115200
- **Data bits**: 8
- **Stop bits**: 1
- **Parity**: None
- **Flow control**: None
---
1. Power on the router and observe the serial terminal output.
2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process.
3. You will see the U-Boot Boot Menu:
```plaintext
*** U-Boot Boot Menu ***
1. Factory mode
2. Startup system (Default)
3. Upgrade firmware
4. Upgrade ATF BL2
5. Upgrade ATF FIP
6. Upgrade single image
7. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
```
4. Select Option 0 by typing 0 and pressing Enter.
5. Input into
```plaintext
MT7981> setenv boot_from ubi
MT7981> saveenv
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
MT7981> printenv
baudrate=115200
boot_from=ubi
...
```
the above indicates system will start from *ubi*.
and then type
```plaintext
MT7981> reset
```
will boot from *ubi*
1. Power on the router and observe the serial terminal output.
2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process.
3. You will see the U-Boot Boot Menu:
```plaintext
*** U-Boot Boot Menu ***
1. Factory mode
2. Startup system (Default)
3. Upgrade firmware
4. Upgrade ATF BL2
5. Upgrade ATF FIP
6. Upgrade single image
7. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
```
4. Choose Option 3: Upgrade Firmware
Enter Upgrade Mode
Select Option 3 by typing 3 and pressing Enter.
Upgrade Methods
You will be prompted to choose between:
```plaintext
*** Upgrading Firmware ***
Run image after upgrading? (Y/n): y
Available load methods:
0 - TFTP client (Default)
1 - Xmodem
2 - Ymodem
3 - Kermit
4 - S-Record
5 - RAM
Select (enter for default): 0
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.10
Input IP netmask: 255.255.255.0
Input file name: wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin
```
Type Enter to proceed. The router will erase the old firmware and write the new one.
Signed-off-by: Jianyu Zhuang <xzjianyu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Maxim Anisimov [Tue, 10 Dec 2024 13:37:02 +0000 (16:37 +0300)]
mediatek/filogic: add support for Cudy AP3000 v1
Hardware:
SoC: MT7981b
RAM: 512 MB
Flash: 256 MB SPI NAND
Ethernet:
1x2.5Gbps (rtl8221b)
WiFi: 2x2 MT7981
Button: Reset
LED: 1x multicolor
Installation
------------
At the moment, firmware installation is only possible via a transition firmware.
It's can be requested from the manufacturer by email to support@cudy.com
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rani Hod [Sun, 22 Dec 2024 00:53:51 +0000 (02:53 +0200)]
linux-firmware: package MediaTek MT7925 Bluetooth firmware
`btusb` fails to start on MT7925 hardware without the appropriate
firmware being loaded first:
```
bluetooth hci0: Direct firmware load for mediatek/mt7925/BT_RAM_CODE_MT7925_1_1_hdr.bin failed with error -2
bluetooth hci0: Falling back to sysfs fallback for: mediatek/mt7925/BT_RAM_CODE_MT7925_1_1_hdr.bin
```
Package firmware for MediaTek MT7925 Bluetooth from `linux-firmware`.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17331
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tianling Shen [Wed, 16 Oct 2024 08:05:40 +0000 (16:05 +0800)]
mediatek: update openembed som7981 support
The board has been redesigned due to previous hardware bugs
(with other reasons maybe).
Changes in new board:
- Added a gpio beeper
- Added a Atmel i2c eeprom
- Added a Atmel i2c ECC accelerator
- Added a Philips RTC module
- Added two RS485
- Removed WPS button
- Replaced USB3 port with M.2 B-key for LTE modules
- Swapped GbE LEDs gpio
Also assigned wifi mac with nvmem binding, added iface setup for failsafe,
increased phy assert time for rtl8221b, and updated LED labels.
Keeping compatibility for old version is not necessary here as only
few samples were sent to those interested in it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17253
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tianling Shen [Wed, 16 Oct 2024 08:05:40 +0000 (16:05 +0800)]
kernel: crypto: add atmel i2c hw accelerator support
Add support for Microchip / Atmel ECC/SHA/RNG hw accelerator.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17253
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Jonas Jelonek [Wed, 18 Dec 2024 20:57:22 +0000 (21:57 +0100)]
kernel: netdevices: add driver for Broadcom NetXtreme-C/E
Package bnxt_en kernel module for Broadcom NetXtreme-C/E based Ethernet
network chips like BCM573xx and BCM574xx.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17301
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Eric Fahlgren [Tue, 3 Dec 2024 23:17:05 +0000 (15:17 -0800)]
build: d1: add SUPPORTED_DEVICES
Include specific SUPPORTED_DEVICES values derived from the .dts file.
This makes the generated profiles.json consistent with the 'board_name' from
'ubus call system board'.
Specifically, this fixes a bug in the generated profiles.json that breaks the
ASU clients when selecting the proper image from a build.
See the 'supported_devices' fields here for the incorrect (or incomplete) list:
https://downloads.openwrt.org/releases/24.10.0-rc1/targets/d1/generic/profiles.json
Links: https://forum.openwrt.org/t/owut-openwrt-upgrade-tool/200035/287
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17155
Signed-off-by: Robert Marko <robimarko@gmail.com>
Shymon Samsel [Thu, 19 Dec 2024 17:28:43 +0000 (12:28 -0500)]
ipq-wifi: update to Git HEAD (2024-12-18)
4b849214b137 ipq8074: add TP-Link EAP620 HD v1 BDF Add board file for TP-Link EAP620 HD v1. Sourced from bdwlan_US.bin in stock firmware 1.1.0 Build
20211028
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/17254
Signed-off-by: Robert Marko <robimarko@gmail.com>
Shymon Samsel [Fri, 13 Dec 2024 10:59:04 +0000 (05:59 -0500)]
ipq807x: add support for TP-Link EAP620 HD v1
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 1.4 GHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCA5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (2x2 2.4 GHz 802.11b/g/n/ax)
* Ethernet: AR8031 (10/100/1000BASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2, and 3 respectively.
Be sure to crossover TX and RX.
3. Copy RAM firmware
openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
to a TFTP server's root that is in the same subnet as your AP.
4. Power up the AP hold Ctrl+B in the serial console (115200n8) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip <TFTP server addr>
# setenv ipaddr <addr of AP>
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp -O openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Known Issues:
* 5GHz radio instability (upstream current ath11k build bug maybe?)
Device support directly followed from EAP660HDv1 support
Links: #15832
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/17254
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rosen Penev [Tue, 3 Dec 2024 00:50:22 +0000 (16:50 -0800)]
ramips: rt3050: fix wrong compatible
In the process of upstreaming the local phy driver back in 2017, it
seems rt3050.dtsi was left out when updating the compatible string.
Add device reset as the driver needs it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17257
Signed-off-by: Robert Marko <robimarko@gmail.com>
Sander Vanheule [Sat, 21 Sep 2024 13:09:34 +0000 (15:09 +0200)]
realtek: merge Zyxel GS1900 firmware partitions
The dual-boot partition layout for the Zyxel GS1900 switches results in
6.9MB for both kernel and rootfs. Depending on the package selection,
this may already leave no space for the user overlay.
Merge the two firmware partitions, effectively dropping dual boot
support with OpenWrt. This results in a firmware partition of 13.9MB,
which should leave some room for the future.
To maintain install capabilites on new devices, an image is required
that still fits inside the original partition. The initramfs is used as
factory install image, so ensure this meets the old size constraints.
The factory image can be flashed via the same procedure as vendor images
when reverting to stock, can be installed from stock, or can be launched
via tftpboot.
Link: https://github.com/openwrt/openwrt/issues/16439
Link: https://github.com/openwrt/openwrt/pull/16442
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Sander Vanheule [Sun, 20 Feb 2022 18:50:38 +0000 (19:50 +0100)]
realtek: ZyXEL GS1900-48: drop gpio-restart
GPIO 5 on the RTL8231 is defined reset the system, but fails to actually
do so. This triggers a kernel a number of warnings and backtrace for
GPIO pins that can sleep, such as the RTL8231's. Two warnings are
emitted by libgpiod, and a third warning by gpio-restart itself after it
fails to restart the system:
[ 106.654008] ------------[ cut here ]------------
[ 106.659240] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 106.826218] ---[ end trace
d1de50b401f5a153 ]---
[ 106.962992] ------------[ cut here ]------------
[ 106.968208] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 107.136718] ---[ end trace
d1de50b401f5a154 ]---
[ 111.087092] ------------[ cut here ]------------
[ 111.092271] WARNING: CPU: 0 PID: 4279 at drivers/power/reset/gpio-restart.c:46 gpio_restart_notify+0xc0/0xdc
[ Stack dump and call trace ]
[ 111.256629] ---[ end trace
d1de50b401f5a155 ]---
By removing gpio-restart from this device, we skip the restart-by-GPIO
attempt and rely only on the watchdog for restarts, which is already the
de facto behaviour.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Rosen Penev [Sat, 22 Jun 2024 18:43:03 +0000 (11:43 -0700)]
ath79: ap5030dn: use label-mac-device property
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17311
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fabian Bläse [Fri, 20 Dec 2024 09:38:31 +0000 (10:38 +0100)]
mvebu: rb5009: add label-mac-device
Add the label-mac-device alias.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Link: https://github.com/openwrt/openwrt/pull/17313
Signed-off-by: Robert Marko <robimarko@gmail.com>
Lorenz Brun [Fri, 20 Dec 2024 22:37:01 +0000 (23:37 +0100)]
octeon: enable AT803x PHY driver
The AR8035 PHY is used in most Octeon boards supported by OpenWRT (all
the Ubiquiti routers at least). To be able to use its PHY-specific
functionality (cable testing, LED Control, ...) it should be built on
Octeon. It also needs the regulator framework, so enable that as well.
These boards are not space-constrained, so this really has no downsides.
Tested on an EdgeRouter Lite, cable tests now work with ethtool-full.
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Link: https://github.com/openwrt/openwrt/pull/17318
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hannu Nyman [Thu, 19 Dec 2024 18:45:40 +0000 (20:45 +0200)]
busybox: Fix hexdump applet
Fix the hexdump applet's formatting with certain format types
by applying the upstream fix for 1.37.0.
Also refresh patches.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/17308
[Changed to 002- patch file name prefix]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Thu, 19 Dec 2024 19:01:20 +0000 (14:01 -0500)]
kernel: bump 6.6 to 6.6.67
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.67
All patches automatically rebased.
Build system: x86/64
Build-tested: flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3, x86/64
Run-tested: flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3, x86/64
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17309
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Marco von Rosenberg [Wed, 18 Dec 2024 22:32:42 +0000 (23:32 +0100)]
generic: fix BCM54612E suspend/resume backport patch
This backport patch inserted suspend/resume callbacks
for the wrong PHY driver.
The fixed patch is needed for Huawei AP5030DN
to initialize its second PHY.
Refresh all affected patch with make target/linux/refresh.
Fixes: 06cdc07f8cc7 ("ath79: add support for Huawei AP5030DN")
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/17312
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Jonas Jelonek [Wed, 13 Nov 2024 22:25:09 +0000 (22:25 +0000)]
mediatek: filogic: bpi-r4: set netdev-name for sfp ports
Sets openwrt,netdev-name for the gmac nodes in the dts of BPI-R4 which
correspond to the two sfp slots. By default they are automatically
named as eth1 and eth2 in bad order, however 'SFP1-WAN' and 'SFP2-LAN'
are printed on the PCB and the official metal case has labels 'SFP-WAN'
and 'SFP-LAN'. Thus, label the ports accordingly to match the
board/case labels.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Jonas Jelonek [Sun, 10 Nov 2024 00:43:23 +0000 (00:43 +0000)]
mediatek: filogic: bpi-r3: set netdev-name for sfp1 port
Sets openwrt,netdev-name for the gmac1 node in the dts of BPI-R3, which
corresponds to the sfp1 slot, to have a proper naming and match the
label on the official BPI-R3 metal case. This renames the port from eth1
to sfp1.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Jonas Jelonek [Mon, 25 Nov 2024 23:04:15 +0000 (23:04 +0000)]
mediatek: filogic: support openwrt,netdev-name for renaming interfaces
Add support in filogic subtarget for our own custom property
`openwrt,netdev-name` in the device tree instead of `label` for
renaming interfaces. This was suggested upstream to avoid potential
conflicts [1].
[1] https://lore.kernel.org/netdev/
20240709124503.pubki5nwjfbedhhy@skbuf/
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Florian Maurer [Sat, 14 Dec 2024 11:38:28 +0000 (12:38 +0100)]
hostapd: fix call to hostapd reload
access to undeclared variable radio In [anonymous function](), file /usr/share/hostap/hostapd.uc, line 830, byte 45:
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Felix Fietkau [Thu, 19 Dec 2024 05:44:30 +0000 (06:44 +0100)]
wifi-scripts: fix phy index lookup in device_capabilities
For renamed phys, the index cannot be derived from the name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 19 Dec 2024 05:26:59 +0000 (06:26 +0100)]
hostapd: fix passing radio parameter in wpa_supplicant calls
Fixes accessing PHY status in AP+STA configurations
Signed-off-by: Felix Fietkau <nbd@nbd.name>
John Audia [Sat, 14 Dec 2024 20:02:19 +0000 (15:02 -0500)]
kernel: bump 6.6 to 6.6.66
Update patch set for new release and add required kernel option
CONFIG_ZRAM_TRACK_ENTRY_ACTIME to generic config
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.66
Manually rebased:
bcm27xx/patches-6.6/950-0092-MMC-added-alternative-MMC-driver.patch
bcm53xx/patches-6.6/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
starfive/patches-6.6/1000-serial-8250_dw-Add-starfive-jh7100-hsuart-compatible.patch
Removed upstreamed:
bcm27xx/patches-6.6/950-0029-vc4_hdmi-Avoid-log-spam-for-audio-start-failure.patch[1]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.66&id=
e0388a95736abd1f5f5a94221dd1ac24eacbd4d7
Build system: x86/64
Build-tested: bcm27xx/bcm2712, flogic/glinet_gl-mt6000, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3, x86/64
Run-tested: bcm27xx/bcm2712, flogic/glinet_gl-mt6000, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3, x86/64
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17271
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Sun, 16 Jun 2024 19:40:53 +0000 (12:40 -0700)]
ath79: tplink,deco-s4-v2: use nvmem for cal
Userspace handling is deprecated. MAC address stuff needs to remain
handled in userspace as it's encrypted. Maybe an NVMEM driver can be
written in the future...
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17276
Signed-off-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Wed, 18 Dec 2024 09:35:21 +0000 (10:35 +0100)]
firewall4: update to Git HEAD (2024-12-18)
e00958884416 fw4: do not add physical devices for soft offload
dfbcc1cd127c fw4: skip not existing netdev names in flowtable device list
18fc0ead19fa init: use the reload data trigger to reload firewall on procd data changes
Fixes: https://github.com/openwrt/openwrt/issues/13410
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Robert Marko [Wed, 18 Dec 2024 09:55:01 +0000 (10:55 +0100)]
apk: disable tests
Currently if the host system has cmocka installed it will leak the host
path and try to use the host cmocka and build tests.
This will obviously fail, so backport upstream commit allowing disabling
of tests and disable building them.
Fixes: openwrt/packages#25456
Link: https://github.com/openwrt/openwrt/pull/17297
Signed-off-by: Robert Marko <robimarko@gmail.com>
Chukun Pan [Tue, 10 Dec 2024 15:02:09 +0000 (23:02 +0800)]
linux-firmware: ath11k: add QCA2066 firmware
Add QCA2066 firmware package, ath11k is already supported.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17260
Signed-off-by: Robert Marko <robimarko@gmail.com>
Chukun Pan [Mon, 16 Dec 2024 15:09:26 +0000 (23:09 +0800)]
qualcommax: fix usb regulator supply for RT-AX89X
The qusb_phy node looks for the following supply:
"vdd", "vdda-pll", "vdda-phy-dpdm"
And ssphy node looks for the following supply:
"vdda-phy", "vdda-pll"
So fix the usb regulator supply for RT-AX89X.
Fixes: 1306237 ("qualcommax: use PHY regulator for USB GPIO")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17290
Signed-off-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Tue, 17 Dec 2024 20:57:44 +0000 (21:57 +0100)]
unetd: update to Git HEAD (2024-12-17)
93461ca4c827 unet-cli: only apply defaults on create
3e5766783d5d unet-tool: add support for confirming password
074d3659ca4a unet-cli: confirm password when creating new seed based key
bf3488a3807a unet-cli: add add/set-local-host command
9eb57c528461 unet-cli: add support for setting interface zone
a0a2d80f3459 ubus: add firewall rules for network port/pex_port via procd
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 17 Dec 2024 20:54:14 +0000 (21:54 +0100)]
procd: add support for reload triggers on data change
This can be useful to reload the firewall when procd firewall data changes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 17 Dec 2024 20:21:37 +0000 (21:21 +0100)]
procd: do not overwrite service data by default
Allows a running servie to manage its own data if untouched by the init script
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 17 Dec 2024 20:53:36 +0000 (21:53 +0100)]
procd: update to Git HEAD (2024-12-17)
2e206dbe77ec service: add support for triggers on service/instance data changes
735b48728fca service: remove leftover lines from previous commit
32469644a029 service: allow incremental changes to service properties
fd01fb852302 service: fix double free bug when dealing with data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 17 Dec 2024 19:01:13 +0000 (20:01 +0100)]
netifd: update to Git HEAD (2024-12-17)
058a099f5bc5 interface: fix memleak and reload issue for the zone attribute
ea01ed41f321 interface: remove unnecessary NULL checks before free()
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 17 Dec 2024 13:51:18 +0000 (14:51 +0100)]
unetd: add firewall input rule for global port
Ensure that peers can be exchanged over any interface
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Linus Walleij [Sun, 17 Nov 2024 21:47:27 +0000 (22:47 +0100)]
kirkwood: Make the Marvell DSA switch a module
Not all Kirkwood systems have the Marvell MV88E6XXX switches.
Drop those from the generic config and add them as modules
in the systems that have it.
This was inferred by inspecting the upstream DTS files for any
mv88e* strings and adding the mv88e6xxx kmod package to those
that have an upstream device tree with an MV88E6xxx switch
and an OpenWrt image target.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Felix Fietkau [Mon, 16 Dec 2024 12:03:26 +0000 (13:03 +0100)]
unetd: update to Git HEAD (2024-12-16)
d22d7db581d5 bpf_skb_utils.h: add missing include to fix build against newer kernel headers
bbd3e0eb1419 host: fix peer routes on a node acting as gateway
b17164751fc7 unet-tool: add support for generating keys from salt + seed passphrase
041e05870c20 unet-tool: add support for dumping pubkey from signed file
b58920d420cb unet-tool: add support for extracting network data from signed bin file
f335f5b40b4e unet-cli: add support for generating key from seed
8b1f1d099352 unet-cli: add support for importing networks from signed data
188ba05eadf2 unet-cli: add missing command line help for import
8f15fc306a40 unet-cli: fix add-ssh-host with seed keys
486bc3b86dc2 pex-msg: enable broadcast for global PEX socket
e4a24cdfbc1c unet-cli: fix defaults on create
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rosen Penev [Sat, 14 Dec 2024 22:26:25 +0000 (14:26 -0800)]
ath79: fix tl-wa eth1 mac
This is using mac-base and so a 0 needs to be added.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17274
Signed-off-by: Robert Marko <robimarko@gmail.com>
Daniel Golle [Sun, 15 Dec 2024 23:58:27 +0000 (23:58 +0000)]
mediatek: add pending patches fixing video output on MT7623N
Add a bunch of fixes for HDMI output and Mali-450 GPU rendering on
MT7623N, ie. the BananaPi R2.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Andrew MacIntyre [Fri, 29 Nov 2024 06:06:02 +0000 (17:06 +1100)]
lantiq/xrx200: move 8M flash devices to a small flash subtarget
Images for xrx200 8M flash are either not building due to image
size (TD-W8970, TD-W8980) or building such that the available
free space in the overlayfs is too little to be useful.
To keep images for these devices buildable, move them into a
small flash variant of the xrx200 subtarget. As these devices
are NOR flash only, remove NAND and UBI references from the
kernel config to gain some additional image size reduction.
The apparent 8M flash devices Arcadyan VGV7510KW22-brn,
Arcadyan VGV7519-brn and Lantiq Easy80920-nor seem to exist in
order to create special "factory" installation images for these
devices (which actually have larger flash: 16MB for the
Arcardyan devices; 64MB for the Lantiq device). As a
considerable amount of surgery would appear to be required to
the uboot-lantiq package structure to separate the "factory"
from the "sysupgrade" device recipes for these devices they
remain in the xrx200 target - if factory images aren't now
created, 23.05.x factory images should suffice for initial
installation.
Tested on: Netgear DM200, TP-Link TD-W8980,
AVM Fritz7490 (xrx200 subtarget: image build only)
Fixes: https://github.com/openwrt/openwrt/issues/16761
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
Link: https://github.com/openwrt/openwrt/pull/17113
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Sun, 15 Dec 2024 14:30:52 +0000 (09:30 -0500)]
kernel: generic: tg3: Fix DMA allocations on 57766 devices
At the request of rsalvaterra, add this patch to fix an issue
affecting tg3 ethernet interfaces[1].
1. https://github.com/openwrt/openwrt/pull/17271#issuecomment-
2543836518
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17282
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Shiji Yang [Thu, 12 Dec 2024 14:40:08 +0000 (22:40 +0800)]
ath79: fix ath9k calibration data size for AR9132
For ath9k NICs older than AR9287, The eeprom size is 0xeb8.
Fixes: https://github.com/openwrt/openwrt/issues/17196
Fixes: 74f2df9dbccd ("ath79: mtd-cal-data removals")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17261
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Shiji Yang [Sat, 14 Dec 2024 04:11:24 +0000 (12:11 +0800)]
ramips: fix 2.4G wmac eeprom offset for TL-WR902AC v4
The eeprom data offset on 2.4GHz wmac is wrong. It is obvious that
this is a copy & paste issue.
Suggested-by: @cgm999 on https://github.com/openwrt/openwrt/issues/13969
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17263
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Andre Heider [Sat, 14 Dec 2024 10:27:09 +0000 (11:27 +0100)]
base-files: fix shell scope error for the default LED brightness
This fixes "sh: write error: Invalid argument" for all default!=1 LEDs
as an empty $brightness was used.
Setting up LEDs via luci also now works again.
Fixes
cbdfd03e: "base-files: add option to set LED brightness"
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/issues/17269
Signed-off-by: John Crispin <john@phrozen.org>
John Audia [Thu, 12 Dec 2024 13:19:59 +0000 (08:19 -0500)]
kernel: bump 6.6 to 6.6.65
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.65
Update to checksum only/no patches required a rebase.
Per the changelog, this is a trivial upstream bump with only 4
commits, 2 of which being reverts.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17217
Signed-off-by: Robert Marko <robimarko@gmail.com>
John Audia [Mon, 9 Dec 2024 23:19:18 +0000 (00:19 +0100)]
kernel: bump 6.6 to 6.6.64
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.64
Manually rebased:
generic/hack-6.6/780-usb-net-MeigLink_modem_support.patch
bcm27xx/patches-6.6/950-0585-drm-vc4-Introduce-generation-number-enum.patch
bcm27xx/patches-6.6/950-0610-drm-vc4-hvs-Support-BCM2712-HVS.patch
bcm27xx/patches-6.6/950-0829-vc4-hvs-Add-support-for-D0-register-changes.patch
Removed upstreamed:
bcm27xx/patches-6.6/950-0597-drm-vc4-hdmi-Avoid-hang-with-debug-registers-when-su.patch[1]
bcm27xx/patches-6.6/950-0599-drm-vc4-Fix-dlist-debug-not-resetting-the-next-entry.patch[2]
bcm27xx/patches-6.6/950-0600-drm-vc4-Remove-incorrect-limit-from-hvs_dlist-debugf.patch[3]
bcm27xx/patches-6.6/950-0708-drm-vc4-Correct-logic-on-stopping-an-HVS-channel.patch[4]
ramips/patches-6.6/002-01-v6.13-clk-ralink-mtmips-fix-clock-plan-for-Ralink-SoC-RT38.patch[5]
ramips/patches-6.6/002-02-v6.13-clk-ralink-mtmips-fix-clocks-probe-order-in-oldest-r.patch[6]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.64&id=
223ee2567a55e4f80315c768d2969e6a3b9fb23d
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.64&id=
8182b5ca19c6f173b6498d1c6d3e4b034b76bbde
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.64&id=
52c1716f65a558174e381360bd88f18dae4be85c
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.64&id=
9728b508b01a5eeeac79ceb676364c674dd951ac
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.64&id=
f85a1d06afbcc57ac44176db8f9d7a934979952c
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.64&id=
fbb13732c6ffa9d58cedafabcd5ce8fd7ef8ae5a
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17217
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rosen Penev [Tue, 3 Dec 2024 21:40:28 +0000 (13:40 -0800)]
qualcommax: use PHY regulator for USB GPIO
The PHY can handle turning off the GPIOs when turning off all USB ports.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17192
Signed-off-by: Robert Marko <robimarko@gmail.com>
Chuncheng Chen [Thu, 20 Oct 2022 03:43:11 +0000 (11:43 +0800)]
ramips: add support for ASUS 4G-AX56
Specifications:
- Device: ASUS 4g-AX56
- SoC: MT7621AT
- Flash: 128MB
- RAM: 512MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LTE : Fibocom FG621-EA
- LEDs: 1x POWER (white, configurable)
1x 2.4G (white, not configurable)
1x 5G (white, not configurable)
1x WAN (white, not configurable)
1x 3G/4G (white, not configurable)
3x signal (white, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.0.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.0.1
Input TFTP server's IP address: 192.168.0.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_4g-ax56-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Notice:
- LTE module is disable after flash openwrt image so you must active LTE by following two AT command
echo -e "AT+GTAUTOCONNECT=1\r\n" > /dev/ttyUSB0
echo -e "AT+GTRNDIS=1,1\r\n" > /dev/ttyUSB0
- After finish AT command once, you don't need to input command later even if reboot/restore default
Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16752
Signed-off-by: John Crispin <john@phrozen.org>
Die Peter Pan [Sat, 23 Nov 2024 10:23:57 +0000 (05:23 -0500)]
ramips: mt7620: add support for THA-103AC (Version v1.0R)
Hardware
* Mediatek MT7620A + Mediatek MT7610EN
* 64MB RAM
* 8MB NAND (Winbond 25064FVSIG )
Both 2.4GHZ and 5GHZ are working, it is enabled by default since there is no
physical ethernet port in the device.
All LED's and buttons work.
UART: 57600 8N1 3.3V
Installation
Upload the openwrt-ramips-mt7620-trendnet_tha103ac-initramfs-kernel.bin via
the manufacturer firmware upgrade page on the device.
Upon reboot wait +- 3 mins until the green power LED is not flashing anymore
(do not be tempted to switch the device off while the LED is flashing, unless
you are ready for soldering and TTL) and then press the WPS button to enable
the default OpenWrt Wifi AP, the BLUE wifi LED will start flash.
Then install openwrt-ramips-mt7620-trendnet_tha103ac-squashfs-sysupgrade.bin
via OpenWrt.
The integrated power monitoring and relay do not work in OpenWrt as the PL7223
chip source/documentation is unavailable.
Recovery
Mis-configuration can be dealt with using the RESET button to reset to factory,
worst case scenario will require some serious work and soldering, there's pads
on the PCB for both the UART and ETH0, and I soldered and tested that it does
work.
You will have to power the board using the header pins GND & 5V, see the 8-pin
header socket.
Signed-off-by: Die Peter Pan <diepeterpan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17114
Signed-off-by: John Crispin <john@phrozen.org>
Rosen Penev [Mon, 25 Nov 2024 22:33:06 +0000 (14:33 -0800)]
ath79: pqi-air-pen: adjust mac addresses
The original ar71xx version of this device used 1002 as mac address for
both ethernet and wireless. The ath79 version inexplicably changes this
to 2, which seems to be done nowhere else in ath79, indicating it's
bogus.
Restore previous ar71xx assignment. 1002 is used as an ethernet
interface with some other devices as well.
Also remove the bogus caldata userspace extraction. The size is bogus
and it's already handled in dts.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17083
Signed-off-by: John Crispin <john@phrozen.org>
Yaoguang Bai [Tue, 26 Nov 2024 09:18:28 +0000 (17:18 +0800)]
mediatek: filogic: add support for NRadio C8-668GL
NRadio C8-668GL is a Wi-Fi 6 5G cellular router based on MediaTek MT7981B SoC.
- **SoC**: MediaTek MT7981B (2x Cortex-A53, 1.3GHz)
- **RAM**: Nanya NT5AD512M16C4-JR 1GB DDR4
- **Flash**: ESMT FC51L08SFY3A 8GB eMMC
- **Ethernet**:
- 1x 2.5GbE (via GMAC0 and GPY211 PHY, shared with MT7531AE)
- 3x 10/100/1000 Mbps (via MT7531AE, connected to GMAC0)
- 5G Modem: GMAC1 (via GPY211 PHY - RTL8125BG - RM520N-GL)
- **Wi-Fi**: MediaTek MT7976CN (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000)
- **Buttons**: Reset, WPS
- **LEDs**: Power, 5G, 4G, WiFi
- **SIM Slot**: 1x Nano SIM
- **5G Modem**: Quectel RM520N-GL (Snapdragon™ X62)
- **Power**: 12V/2A DC, 5.5×2.1 connector
The MAC addresses are derived from the `fac_mac` field in the `bdinfo` partition, formatted as `fac_mac = HWMAC`. The allocation is as follows:
| Vendor | OpenWrt Interface | Address | Notes |
|---------|-------------------|---------------|------------------------------------------------|
| LAN | br-lan | Label MAC | Default |
| WAN | lan4 | Label MAC+1 | Only when lan4 is switched to WAN |
| 2.4GHz | phy0-ap0 | Label MAC | |
| 5GHz | phy1-ap0 | Label MAC | (Local Admin bit set) |
| Modem | eth1 | Label MAC+2 | |
1. Log in to the router via `http://192.168.66.1`/.
2. Upgrade the official firmware to dual-system mode.
3. Select **Burn second system** and upload the `sysupgrade.bin` image.
- Download the image from the OpenWrt build system or build it yourself using the OpenWrt buildroot.
4. Wait for 30 seconds and click **Switch system**.
5. The device will reboot and switch to OpenWrt.
Set the U-Boot environment variable `boot_system=0` and reboot:
```bash
fw_setenv boot_system 0
```
Power off the router, hold the **WPS button**, and power it back on.
1. Rename the stock firmware file to **`recovery.bin`**.
2. Set your PC's Ethernet IP to **192.168.1.88** and connect it to the lan1 port on the router.
3. Run a TFTP server and place the `recovery.bin` file in its root directory.
4. Power off the router, press and hold the **Reset button**, and power it back on.
5. Release the Reset button when the TFTP server shows activity.
6. Wait for the router to flash the firmware and reboot automatically.
- By default, `lan4` is part of `br-lan` and uses the label MAC address.
- To query the RM520N-GL module, use the following command:
```bash
cat /dev/ttyUSB2 & printf 'ATI\r\n' > /dev/ttyUSB2
```
Signed-off-by: Yaoguang Bai <0xdeadc0de@badguys.club>
Link: https://github.com/openwrt/openwrt/pull/17093
Signed-off-by: John Crispin <john@phrozen.org>
Rosen Penev [Fri, 29 Nov 2024 22:24:38 +0000 (14:24 -0800)]
ath79: usb: remove reset names
Upstream uses devm_reset_control_array_get_optional_shared, which does
not use names. reset-names is also not specified in the documentation.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17118
Signed-off-by: John Crispin <john@phrozen.org>
Rosen Penev [Fri, 29 Nov 2024 04:44:51 +0000 (20:44 -0800)]
ath79: change phy-names to only usb
Both generic-ehci.yaml and generic-ohci.yaml state that phy-names is to
only be usb.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17118
Signed-off-by: John Crispin <john@phrozen.org>
Rosen Penev [Fri, 29 Nov 2024 04:21:20 +0000 (20:21 -0800)]
ath79: usb: remove usb- from reset-names
This matches the upstream PHY driver, which removed it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17118
Signed-off-by: John Crispin <john@phrozen.org>
David Bauer [Sat, 7 Dec 2024 13:47:29 +0000 (14:47 +0100)]
wifi-scripts: don't fail on unset PSK
Don't fail wireless interface bringup on empty PSK set. This is a valid
configuration, resulting in a PSK network which can't be connected to.
It does not fail the bringup of the hostapd process.
Keep failing the interface setup in case a password with invalid length
is used.
This is also beneficial when intending to configure a PPSK network. It
allows to create a network where no PPSK is yet set.
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://github.com/openwrt/openwrt/pull/17197
Signed-off-by: John Crispin <john@phrozen.org>
Georgi Valkov [Thu, 12 Dec 2024 09:05:15 +0000 (11:05 +0200)]
mac80211: refresh patch for ath12k
refresh the following patch for ath12k
001-wifi-ath12k-add-11d-scan-offload-support-and-handle-country-code-for-WCN7850.patch
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17246
Signed-off-by: John Crispin <john@phrozen.org>
Rosen Penev [Tue, 3 Dec 2024 21:29:37 +0000 (13:29 -0800)]
lantiq: use regulator for USB GPIO
One is already present. The other one can be implemented in terms of the
PHY.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17250
Signed-off-by: John Crispin <john@phrozen.org>
Felix Fietkau [Fri, 13 Dec 2024 10:04:04 +0000 (11:04 +0100)]
hostapd: fix building mini variants
Move function and add ifdef to avoid undefined reference to hmac_sha256_kdf.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 13 Dec 2024 09:56:50 +0000 (10:56 +0100)]
wifi-scripts: fix mesh/sta setup with ucode scripts
Ensure that the code doesn't pass macaddr_base with the wrong type (null)
to the supplicant setup/start call.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Andreas Gnau [Tue, 28 Feb 2023 11:24:57 +0000 (16:54 +0530)]
dropbear: Name pid file by uci section name
Name the pidfile of each dropbear instance according to the
corresponding uci section name. This enables a 1:1 mapping between the
definition of the service instance and its process.
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/15177
Signed-off-by: John Crispin <john@phrozen.org>
Rosen Penev [Tue, 3 Dec 2024 21:37:21 +0000 (13:37 -0800)]
ipq40xx: use PHY to control USB GPIO
Instead of using regulator-output to manually control USB GPIO, let the
PHY handle it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17221
Signed-off-by: John Crispin <john@phrozen.org>
Jiale Liu [Sun, 14 Apr 2024 16:27:49 +0000 (00:27 +0800)]
base-files: fix luci TZ default show zonename
fix default timezone to correct GMT0,
origin value 'UTC' is zonename, not timezone.
Signed-off-by: Jiale Liu <admin@licsber.site>
Link: https://github.com/openwrt/openwrt/pull/15128
Signed-off-by: John Crispin <john@phrozen.org>
Sybil127 [Thu, 23 May 2024 16:49:54 +0000 (18:49 +0200)]
hostapd: add support for rxkh_file
Initial support for dynamic reload of RxKHs.
In order to check if RxKHs need reloading.
RxKHs defined in the rxkh_file first has to be parsed and formated,
the same way as hostapd will read from the file and also output,
with the command GET_RXKHS.
Then each list of RxKHs can be hashed and compared.
Ucode implementation of hostapds rkh_derive_key() function.
Hostapd converts hex keys with 128-bits or more when less than 256-bits
to 256-bits, and truncates those that are more than 256-bits.
See: https://w1.fi/cgit/hostap/commit/hostapd/config_file.c?id=
245fc96e5f4b1c566b7eaa19180c774307ebed79
Signed-off-by: Sybil127 <sybil127@outlook.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sybil127 [Thu, 23 May 2024 15:43:07 +0000 (17:43 +0200)]
wifi-scripts: introduce rxkh_file uci option
With rxkh_file, hostapd will read a list of RxKHs from a text file.
This also makes it possible for hostapd to dynamically reload RxKHs.
RxKHs defined in rxkh_file should be formated as described in hostapd.conf,
with one entry per line.
R0KH/R1KH format:
r0kh=<MAC address> <NAS Identifier> <256-bit key as hex string>
r1kh=<MAC address> <R1KH-ID> <256-bit key as hex string>
Reworked behavior of the uci options r0kh and r1kh.
When rxkh_file is not configured:
Instead of appending the RxKHs to the hostapd bss configuration.
They will be added to a interface specific file with name
/var/run/hostapd-phyX-apX.rxkh.
This file will be used as the rxkh_file in the hostapd bss configuration.
When rxkh_file is configured:
The specified file will be used in the hostapd bss configuration,
and will be the only source for configured RxKHs.
All RxKHs defined with the uci options r0kh or r1kh will be ignored.
Signed-off-by: Sybil127 <sybil127@outlook.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 9 Dec 2024 19:09:15 +0000 (20:09 +0100)]
wifi-scripts: add macaddr_base wifi-device option
This can be used to configure the base mac address from which all
interface mac addresses are derived
Signed-off-by: Felix Fietkau <nbd@nbd.name>
David Bauer [Thu, 12 Dec 2024 15:36:50 +0000 (16:36 +0100)]
wifi-scripts: fix failing mesh setup with missing wpa_supplicant
The initialization of mesh interfaces currently fail when wpa_supplicant
is not installed. This is due to the script calling the wpa_supplicant
feature indicator without verifying wpa_supplicant is installed at all.
To avoid failing, first check if wpa_supplicant is installed before
determining the available featureset.
Signed-off-by: David Bauer <mail@david-bauer.net>
John Crispin [Thu, 12 Dec 2024 14:43:35 +0000 (15:43 +0100)]
Revert "kernel: modules: fix led-group-multi-color patch"
This reverts commit
1cea889c96a8df4e91236e269539b086d519a60a.
This reverts commit
5fd86d66c15fc4d6f5076f7d07c91e0690d91531.
The patch is causing build servers to fail. Revert it for now.
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Thu, 12 Dec 2024 12:52:43 +0000 (13:52 +0100)]
kernel: modules: fix led-group-multi-color patch
Fixes: 5fd86d6 ("kernel: modules: add support for led-group-multicolor")
Signed-off-by: John Crispin <john@phrozen.org>