openwrt/staging/blogic.git
8 years agodrm/radeon: Also call cursor_move_locked when the cursor size changes
Michel Dänzer [Thu, 27 Oct 2016 04:03:23 +0000 (13:03 +0900)]
drm/radeon: Also call cursor_move_locked when the cursor size changes

The cursor size also affects the register programming.

Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
8 years agodrm/amdgpu: Only update the CUR_SIZE register when necessary
Michel Dänzer [Thu, 27 Oct 2016 08:44:07 +0000 (17:44 +0900)]
drm/amdgpu: Only update the CUR_SIZE register when necessary

Normally only necessary when the cursor size changes.

Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
8 years agodrm/amdgpu: Also call cursor_move_locked when the cursor size changes
Michel Dänzer [Thu, 27 Oct 2016 08:01:26 +0000 (17:01 +0900)]
drm/amdgpu: Also call cursor_move_locked when the cursor size changes

The cursor size also affects the register programming.

Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
8 years agodrm/amdgpu: Store CRTC relative amdgpu_crtc->cursor_x/y values
Michel Dänzer [Thu, 27 Oct 2016 08:11:43 +0000 (17:11 +0900)]
drm/amdgpu: Store CRTC relative amdgpu_crtc->cursor_x/y values

We were storing viewport relative coordinates. However, crtc_cursor_set2
and cursor_reset pass amdgpu_crtc->cursor_x/y as the x/y parameters of
cursor_move_locked, which would break if the CRTC isn't located at
(0, 0).

Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
8 years agodrm/amd/amdgpu: enable GUI idle INT after enabling CGCG
Arindam Nath [Fri, 25 Nov 2016 11:25:16 +0000 (16:55 +0530)]
drm/amd/amdgpu: enable GUI idle INT after enabling CGCG

GUI idle interrupts should be enabled only after we
have enabled coarse grain clock gating (CGCG). This
prevents GFX engine generating idle interrupt even
though CGCG is not completely enabled.

Most of the time this goes un-noticed, but on some
Stoney ASICs this results in GFX engine hang after
system resumes from suspend. The issue is not
particular to Stoney though and could have occured
on any ASIC. The patch fixes this issue.

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reported-by: Sunil Uttarwar <Sunil.Uttarwar1@amd.com>
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
8 years agodrm/amdgpu: enable VCE clockgating in Polaris-10/11
Maruthi Srinivas Bayyavarapu [Thu, 17 Nov 2016 11:59:50 +0000 (17:29 +0530)]
drm/amdgpu: enable VCE clockgating in Polaris-10/11

VCE clocks are set to be disabled, when not in use.

Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
8 years agodrm/amdgpu: fix CI bug uvd status not true in debugfs.
Rex Zhu [Fri, 25 Nov 2016 11:23:06 +0000 (19:23 +0800)]
drm/amdgpu: fix CI bug uvd status not true in debugfs.

can't get uvd's state by uvd_enabled. uvd_enabled
is used for request higher mclk.
in multi-display case, mclk has been in highest clock,
no matter uvd's state changed, uvd_enabled will not
be changed.

Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
8 years agodrm/amdgpu: remove error message when loading driver
Xiangliang Yu [Thu, 24 Nov 2016 08:28:46 +0000 (16:28 +0800)]
drm/amdgpu: remove error message when loading driver

Forget to check UCODE_ID_STORAGE case and will cause to print error
message when loading driver, correct it.

Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
8 years agodrm/amd/powerplay: fix firmware loading failure
Xiangliang Yu [Sun, 20 Nov 2016 15:00:26 +0000 (23:00 +0800)]
drm/amd/powerplay: fix firmware loading failure

For virtualization, firmware loading need the firmware version info,
and will load the right firmware. So, transfer fw_version to toc.

Signed-off-by: Frank Min <Frank.Min@amd.com>
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
8 years agodrm/amdgpu: fix bug mclk can't change on Polaris
Rex Zhu [Wed, 23 Nov 2016 10:09:22 +0000 (18:09 +0800)]
drm/amdgpu: fix bug mclk can't change on Polaris

the root cause is we gate the clock to uvd vcpu.
mclk's change should need the response from uvd if
it is power on.

Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
8 years agodrm/amdgpu: refine uvd 6.0 clock gate feature.
Rex Zhu [Wed, 9 Nov 2016 06:26:16 +0000 (14:26 +0800)]
drm/amdgpu: refine uvd 6.0 clock gate feature.

Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
8 years agodrm/amdgpu/gfx8: move eop programming per queue
Alex Deucher [Tue, 15 Nov 2016 22:33:09 +0000 (17:33 -0500)]
drm/amdgpu/gfx8: move eop programming per queue

It's per queue not per pipe.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
8 years agoRevert "drm/amdgpu: use the kernel zone memory size as the max remote memory in amdgpu"
Alex Deucher [Tue, 15 Nov 2016 21:55:53 +0000 (16:55 -0500)]
Revert "drm/amdgpu: use the kernel zone memory size as the max remote memory in amdgpu"

This reverts commit a693e050edfe794fea81d7cfe72429a406aa380b.

This breaks on systems with huge amounts of system memory as we do not have
enough vram to store the page tables.  Additionally, this is less of an issue
with the recent gtt manager changes.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
8 years agoMerge branch 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daein...
Dave Airlie [Tue, 6 Dec 2016 01:09:21 +0000 (11:09 +1000)]
Merge branch 'exynos-drm-next' of git://git./linux/kernel/git/daeinki/drm-exynos into drm-next

Just refactoring HDMI driver by using infoframe helper
function, fixing GSC Kconfig dependency issue and including trivial
cleanups.

* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/exynos: Use VIDEO_SAMSUNG_EXYNOS_GSC=n as GSC Kconfig dependency
  drm/exynos: gsc: fix spelling mistakes
  exynos-drm: Fix error messages to print flags and size
  drm/exynos/hdmi: refactor infoframe code

8 years agoMerge branch 'drm-next-4.10' of git://people.freedesktop.org/~agd5f/linux into drm...
Dave Airlie [Tue, 6 Dec 2016 01:01:33 +0000 (11:01 +1000)]
Merge branch 'drm-next-4.10' of git://people.freedesktop.org/~agd5f/linux into drm-next

- lots of code cleanup
- lots of bug fixes
- expose rpm based fan info via hwmon
- lots of clock and powergating fixes
- SI register header cleanup and conversion to common format used by newer asics

* 'drm-next-4.10' of git://people.freedesktop.org/~agd5f/linux: (54 commits)
  drm/amdgpu: drop is_display_hung from display funcs
  drm/amdgpu/uvd: reduce IB parsing overhead on UVD5+ (v2)
  drm/amdgpu/uvd: consolidate code for fetching addr from ctx
  drm/amdgpu: Disable DPM in virtualization
  drm/amdgpu: use AMDGPU_GEM_CREATE_VRAM_CLEARED for VM PD/PTs (v2)
  drm/amdgpu: improve AMDGPU_GEM_CREATE_VRAM_CLEARED handling (v2)
  drm/amdgpu: fix error handling in amdgpu_bo_create_restricted
  drm/amdgpu: fix amdgpu_fill_buffer (v2)
  drm/amdgpu: remove amdgpu_irq_get_delayed
  amdgpu: Wrap dev_err() calls on vm faults with printk_ratelimit()
  amdgpu: Use dev_err() over vanilla printk() in vm_decode_fault()
  drm/amd/amdgpu: port of DCE v6 to new headers (v3)
  drm/amdgpu: cleanup unused iterator members for sdma v2.4
  drm/amdgpu: cleanup unused iterator members for sdma v3
  drm/amdgpu:impl vgt_flush for VI(V5)
  drm/amdgpu: enable uvd mgcg for Fiji.
  drm/amdgpu: refine cz uvd clock gate logic.
  drm/amdgpu: change log level to KERN_INFO in ci_dpm.c
  drm/amdgpu: always un-gate UVD REGS path.
  drm/amdgpu/sdma: fix typo in packet setup
  ...

8 years agoMerge branch 'drm-etnaviv-next' of git://git.pengutronix.de/lst/linux into drm-next
Dave Airlie [Tue, 6 Dec 2016 01:00:16 +0000 (11:00 +1000)]
Merge branch 'drm-etnaviv-next' of git://git.pengutronix.de/lst/linux into drm-next

- fix dma-buf export path to return correct SG table
- trivially implement direct dma-buf mapping
- allow DRAW_INSTANCED commands in validator
- make the driver work on i.MX6SX, yielding a working 2D/3D stack
together with Mareks MXS DRM driver

* 'drm-etnaviv-next' of git://git.pengutronix.de/lst/linux:
  MAINTAINERS: add etnaviv mailinglist
  drm/etnaviv: move linear window on MC1.0 parts if necessary
  drm/etnaviv: don't invoke OOM killer from dump code
  drm/etnaviv: fix gem_prime_get_sg_table to return new SG table
  drm/etnaviv: Allow DRAW_INSTANCED commands
  drm/etnaviv: implement dma-buf mmap

8 years agoMerge branch 'linux-4.10' of git://github.com/skeggsb/linux into drm-next
Dave Airlie [Mon, 5 Dec 2016 23:34:43 +0000 (09:34 +1000)]
Merge branch 'linux-4.10' of git://github.com/skeggsb/linux into drm-next

- BIT_PERF_PTRS uses 32-bit pointers to its subtables, we were parsing
them as 16-bit, causing various issues on newer boards.
- Support for MXM on GM20x and up.
- More display-related fixes.

* 'linux-4.10' of git://github.com/skeggsb/linux:
  drm/nouveau/mxm: warn more loudly on unsupported DCB version
  drm/nouveau/mxm: handle DCB 4.1 modification
  drm/nouveau/bios/mxm: handle digital connector table 1.1
  drm/nouveau: Queue hpd_work on (runtime) resume
  drm/nouveau: Rename acpi_work to hpd_work
  drm/nouveau/kms/nv50: Fix atomic pageflip events.
  drm/nouveau/fb/ram/gp100-: fix memory detection where FBP_NUM != FBPA_NUM
  drm/nouveau/bios/volt: pointers are 32-bit
  drm/nouveau/bios/vmap: pointers are 32-bit
  drm/nouveau/bios/timing: pointers are 32-bit
  drm/nouveau/bios/therm: pointers are 32-bit
  drm/nouveau/bios/perf: pointers are 32-bit
  drm/nouveau/bios/iccsense: pointers are 32-bit
  drm/nouveau/bios/fan: pointers are 32-bit
  drm/nouveau/bios/cstep: pointers are 32-bit
  drm/nouveau/bios/boost: pointers are 32-bit

8 years agodrm/nouveau/mxm: warn more loudly on unsupported DCB version
Ben Skeggs [Mon, 5 Dec 2016 23:03:59 +0000 (09:03 +1000)]
drm/nouveau/mxm: warn more loudly on unsupported DCB version

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
8 years agodrm/nouveau/mxm: handle DCB 4.1 modification
Ben Skeggs [Mon, 5 Dec 2016 23:03:04 +0000 (09:03 +1000)]
drm/nouveau/mxm: handle DCB 4.1 modification

Allows MXM DCB modification to be handled on GM20x and newer boards.

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
8 years agodrm/nouveau/bios/mxm: handle digital connector table 1.1
Ben Skeggs [Mon, 5 Dec 2016 22:59:31 +0000 (08:59 +1000)]
drm/nouveau/bios/mxm: handle digital connector table 1.1

I suspect the version bump is just to signify that the table now specifies
pad macro/links instead of SOR/sublinks.

For our usage of the table, just recognising the new version is enough.

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
8 years agodrm/exynos: Use VIDEO_SAMSUNG_EXYNOS_GSC=n as GSC Kconfig dependency
Javier Martinez Canillas [Tue, 29 Nov 2016 14:40:51 +0000 (11:40 -0300)]
drm/exynos: Use VIDEO_SAMSUNG_EXYNOS_GSC=n as GSC Kconfig dependency

Commit aeefb36832e5 ("drm/exynos: gsc: add device tree support and remove
usage of static mappings") made the DRM_EXYNOS_GSC Kconfig symbol to only
be selectable if the exynos-gsc V4L2 driver isn't enabled, since both use
the same HW IP block.

But added the dependency as depends on !VIDEO_SAMSUNG_EXYNOS_GSC which is
not correct since Kconfig expressions are not boolean but tristate. So it
will only evaluate to 'n' if VIDEO_SAMSUNG_EXYNOS_GSC=y but will evaluate
to 'm' if VIDEO_SAMSUNG_EXYNOS_GSC=m.

This means that both the V4L2 and DRM drivers can be enabled if the former
is enabled as a module, which isn't what we want since otherwise 2 drivers
could attempt to use the hardware at the same time.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
8 years agodrm/exynos: gsc: fix spelling mistakes
Colin Ian King [Wed, 2 Nov 2016 02:23:36 +0000 (20:23 -0600)]
drm/exynos: gsc: fix spelling mistakes

Trivial fixes to spelling mistakes "precalser" to "prescaler"
in dev_err messages

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
8 years agoexynos-drm: Fix error messages to print flags and size
Shuah Khan [Wed, 10 Aug 2016 17:30:36 +0000 (11:30 -0600)]
exynos-drm: Fix error messages to print flags and size

Fix exynos_drm_gem_create() error messages to include flags and size when
flags and size are invalid.

Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
8 years agodrm/exynos/hdmi: refactor infoframe code
Andrzej Hajda [Mon, 7 Nov 2016 15:04:43 +0000 (16:04 +0100)]
drm/exynos/hdmi: refactor infoframe code

Use core helpers to generate infoframes and generate vendor frame if necessary.

Changelog:
- changed 'ret >= 0' checks to '!ret'

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
8 years agoBackmerge tag 'v4.9-rc8' into drm-next
Dave Airlie [Mon, 5 Dec 2016 07:11:48 +0000 (17:11 +1000)]
Backmerge tag 'v4.9-rc8' into drm-next

Linux 4.9-rc8

Daniel requested this so we could apply some follow on fixes cleanly to -next.

8 years agoLinux 4.9-rc8
Linus Torvalds [Sun, 4 Dec 2016 20:50:51 +0000 (12:50 -0800)]
Linux 4.9-rc8

8 years agoMerge tag 'drm-fixes-for-v4.9-rc8' of git://people.freedesktop.org/~airlied/linux
Linus Torvalds [Sun, 4 Dec 2016 00:40:21 +0000 (16:40 -0800)]
Merge tag 'drm-fixes-for-v4.9-rc8' of git://people.freedesktop.org/~airlied/linux

Pull drm fixes from Dave Airlie:
 "A pretty small pull request: a couple of AMD powerxpress regression
  fixes and a power management fix, a couple of i915 fixes and one hdlcd
  fix, along with one core don't oops because of incorrect API usage fix"

* tag 'drm-fixes-for-v4.9-rc8' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: drop the struct_mutex when wedged or trying to reset
  drm/i915: Don't touch NULL sg on i915_gem_object_get_pages_gtt() error
  drm: Don't call drm_for_each_crtc with a non-KMS driver
  drm/radeon: fix check for port PM availability
  drm/amdgpu: fix check for port PM availability
  drm/amd/powerplay: initialize the soft_regs offset in struct smu7_hwmgr
  drm: hdlcd: Fix cleanup order

8 years agoMerge tag 'drm-intel-fixes-2016-12-01' of git://anongit.freedesktop.org/git/drm-intel...
Dave Airlie [Sat, 3 Dec 2016 20:31:26 +0000 (06:31 +1000)]
Merge tag 'drm-intel-fixes-2016-12-01' of git://anongit.freedesktop.org/git/drm-intel into drm-fixes

2 intel fixes.

* tag 'drm-intel-fixes-2016-12-01' of git://anongit.freedesktop.org/git/drm-intel:
  drm/i915: drop the struct_mutex when wedged or trying to reset
  drm/i915: Don't touch NULL sg on i915_gem_object_get_pages_gtt() error

8 years agoMerge branch 'akpm' (patches from Andrew)
Linus Torvalds [Sat, 3 Dec 2016 02:48:11 +0000 (18:48 -0800)]
Merge branch 'akpm' (patches from Andrew)

Merge more fixes from Andrew Morton:
 "2 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm, vmscan: add cond_resched() into shrink_node_memcg()
  mm: workingset: fix NULL ptr in count_shadow_nodes

8 years agomm, vmscan: add cond_resched() into shrink_node_memcg()
Michal Hocko [Sat, 3 Dec 2016 01:26:48 +0000 (17:26 -0800)]
mm, vmscan: add cond_resched() into shrink_node_memcg()

Boris Zhmurov has reported RCU stalls during the kswapd reclaim:

  INFO: rcu_sched detected stalls on CPUs/tasks:
   23-...: (22 ticks this GP) idle=92f/140000000000000/0 softirq=2638404/2638404 fqs=23
   (detected by 4, t=6389 jiffies, g=786259, c=786258, q=42115)
  Task dump for CPU 23:
  kswapd1         R  running task        0   148      2 0x00000008
  Call Trace:
    shrink_node+0xd2/0x2f0
    kswapd+0x2cb/0x6a0
    mem_cgroup_shrink_node+0x160/0x160
    kthread+0xbd/0xe0
    __switch_to+0x1fa/0x5c0
    ret_from_fork+0x1f/0x40
    kthread_create_on_node+0x180/0x180

a closer code inspection has shown that we might indeed miss all the
scheduling points in the reclaim path if no pages can be isolated from
the LRU list.  This is a pathological case but other reports from Donald
Buczek have shown that we might indeed hit such a path:

        clusterd-989   [009] .... 118023.654491: mm_vmscan_direct_reclaim_end: nr_reclaimed=193
         kswapd1-86    [001] dN.. 118023.987475: mm_vmscan_lru_isolate: isolate_mode=0 classzone=0 order=0 nr_requested=32 nr_scanned=4239830 nr_taken=0 file=1
         kswapd1-86    [001] dN.. 118024.320968: mm_vmscan_lru_isolate: isolate_mode=0 classzone=0 order=0 nr_requested=32 nr_scanned=4239844 nr_taken=0 file=1
         kswapd1-86    [001] dN.. 118024.654375: mm_vmscan_lru_isolate: isolate_mode=0 classzone=0 order=0 nr_requested=32 nr_scanned=4239858 nr_taken=0 file=1
         kswapd1-86    [001] dN.. 118024.987036: mm_vmscan_lru_isolate: isolate_mode=0 classzone=0 order=0 nr_requested=32 nr_scanned=4239872 nr_taken=0 file=1
         kswapd1-86    [001] dN.. 118025.319651: mm_vmscan_lru_isolate: isolate_mode=0 classzone=0 order=0 nr_requested=32 nr_scanned=4239886 nr_taken=0 file=1
         kswapd1-86    [001] dN.. 118025.652248: mm_vmscan_lru_isolate: isolate_mode=0 classzone=0 order=0 nr_requested=32 nr_scanned=4239900 nr_taken=0 file=1
         kswapd1-86    [001] dN.. 118025.984870: mm_vmscan_lru_isolate: isolate_mode=0 classzone=0 order=0 nr_requested=32 nr_scanned=4239914 nr_taken=0 file=1
  [...]
         kswapd1-86    [001] dN.. 118084.274403: mm_vmscan_lru_isolate: isolate_mode=0 classzone=0 order=0 nr_requested=32 nr_scanned=4241133 nr_taken=0 file=1

this is minute long snapshot which didn't take a single page from the
LRU.  It is not entirely clear why only 1303 pages have been scanned
during that time (maybe there was a heavy IRQ activity interfering).

In any case it looks like we can really hit long periods without
scheduling on non preemptive kernels so an explicit cond_resched() in
shrink_node_memcg which is independent on the reclaim operation is due.

Link: http://lkml.kernel.org/r/20161202095841.16648-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Boris Zhmurov <bb@kernelpanic.ru>
Tested-by: Boris Zhmurov <bb@kernelpanic.ru>
Reported-by: Donald Buczek <buczek@molgen.mpg.de>
Reported-by: "Christopher S. Aker" <caker@theshore.net>
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8 years agomm: workingset: fix NULL ptr in count_shadow_nodes
Michal Hocko [Sat, 3 Dec 2016 01:26:45 +0000 (17:26 -0800)]
mm: workingset: fix NULL ptr in count_shadow_nodes

Commit 0a6b76dd23fa ("mm: workingset: make shadow node shrinker memcg
aware") has made the workingset shadow nodes shrinker memcg aware.  The
implementation is not correct though because memcg_kmem_enabled() might
become true while we are doing a global reclaim when the sc->memcg might
be NULL which is exactly what Marek has seen:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000400
  IP: [<ffffffff8122d520>] mem_cgroup_node_nr_lru_pages+0x20/0x40
  PGD 0
  Oops: 0000 [#1] SMP
  CPU: 0 PID: 60 Comm: kswapd0 Tainted: G           O   4.8.10-12.pvops.qubes.x86_64 #1
  task: ffff880011863b00 task.stack: ffff880011868000
  RIP: mem_cgroup_node_nr_lru_pages+0x20/0x40
  RSP: e02b:ffff88001186bc70  EFLAGS: 00010293
  RAX: 0000000000000000 RBX: ffff88001186bd20 RCX: 0000000000000002
  RDX: 000000000000000c RSI: 0000000000000000 RDI: 0000000000000000
  RBP: ffff88001186bc70 R08: 28f5c28f5c28f5c3 R09: 0000000000000000
  R10: 0000000000006c34 R11: 0000000000000333 R12: 00000000000001f6
  R13: ffffffff81c6f6a0 R14: 0000000000000000 R15: 0000000000000000
  FS:  0000000000000000(0000) GS:ffff880013c00000(0000) knlGS:ffff880013d00000
  CS:  e033 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000000000400 CR3: 00000000122f2000 CR4: 0000000000042660
  Call Trace:
    count_shadow_nodes+0x9a/0xa0
    shrink_slab.part.42+0x119/0x3e0
    shrink_node+0x22c/0x320
    kswapd+0x32c/0x700
    kthread+0xd8/0xf0
    ret_from_fork+0x1f/0x40
  Code: 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 3b 35 dd eb b1 00 55 48 89 e5 73 2c 89 d2 31 c9 31 c0 4c 63 ce 48 0f a3 ca 73 13 <4a> 8b b4 cf 00 04 00 00 41 89 c8 4a 03 84 c6 80 00 00 00 83 c1
  RIP  mem_cgroup_node_nr_lru_pages+0x20/0x40
   RSP <ffff88001186bc70>
  CR2: 0000000000000400
  ---[ end trace 100494b9edbdfc4d ]---

This patch fixes the issue by checking sc->memcg rather than
memcg_kmem_enabled() which is sufficient because shrink_slab makes sure
that only memcg aware shrinkers will get non-NULL memcgs and only if
memcg_kmem_enabled is true.

Fixes: 0a6b76dd23fa ("mm: workingset: make shadow node shrinker memcg aware")
Link: http://lkml.kernel.org/r/20161201132156.21450-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Marek Marczykowski-Górecki <marmarek@mimuw.edu.pl>
Tested-by: Marek Marczykowski-Górecki <marmarek@mimuw.edu.pl>
Acked-by: Vladimir Davydov <vdavydov.dev@gmail.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Cc: <stable@vger.kernel.org> [4.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8 years agokbuild: fix building bzImage with CONFIG_TRIM_UNUSED_KSYMS enabled
Nicolas Pitre [Fri, 2 Dec 2016 20:11:50 +0000 (15:11 -0500)]
kbuild: fix building bzImage with CONFIG_TRIM_UNUSED_KSYMS enabled

When building a specific target such as bzImage, modules aren't normally
built.  However if CONFIG_TRIM_UNUSED_KSYMS is enabled, no built modules
means none of the exported symbols are used and therefore they will all
be trimmed away from the final kernel.  A subsequent "make modules" will
fail because modpost cannot find the needed symbols for those modules in
the kernel binary.

Let's make sure modules are also built whenever CONFIG_TRIM_UNUSED_KSYMS
is enabled and that the kernel binary is properly rebuilt accordingly.

Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8 years agoMerge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm...
Linus Torvalds [Fri, 2 Dec 2016 21:34:37 +0000 (13:34 -0800)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Arnd Bergmann:
 "This should be the last set of bugfixes for arm-soc in v4.9. None of
  these are critical regressions, but it would be nice to still get them
  merged.

   - On the Juno platform, the idle latency was described wrong, leading
     to suboptimal cpuidle tuning.

   - Also on the same platform, PCI I/O space was set up incorrectly and
     could not work.

   - On the sti platform, a syntactically incorrect DT entry caused
     warnings.

   - The newly added 'gr8' platform has somewhat confusing file names,
     which we rename for consistency"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: dts: juno: fix cluster sleep state entry latency on all SoC versions
  arm64: dts: juno: Correct PCI IO window
  ARM: dts: STiH407-family: fix i2c nodes
  ARM: gr8: Rename the DTSI and relevant DTS

8 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Linus Torvalds [Fri, 2 Dec 2016 19:45:27 +0000 (11:45 -0800)]
Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:

 1) Lots more phydev and probe error path leaks in various drivers by
    Johan Hovold.

 2) Fix race in packet_set_ring(), from Philip Pettersson.

 3) Use after free in dccp_invalid_packet(), from Eric Dumazet.

 4) Signnedness overflow in SO_{SND,RCV}BUFFORCE, also from Eric
    Dumazet.

 5) When tunneling between ipv4 and ipv6 we can be left with the wrong
    skb->protocol value as we enter the IPSEC engine and this causes all
    kinds of problems. Set it before the output path does any
    dst_output() calls, from Eli Cooper.

 6) bcmgenet uses wrong device struct pointer in DMA API calls, fix from
    Florian Fainelli.

 7) Various netfilter nat bug fixes from FLorian Westphal.

 8) Fix memory leak in ipvlan_link_new(), from Gao Feng.

 9) Locking fixes, particularly wrt. socket lookups, in l2tp from
    Guillaume Nault.

10) Avoid invoking rhash teardowns in atomic context by moving netlink
    cb->done() dump completion from a worker thread. Fix from Herbert
    Xu.

11) Buffer refcount problems in tun and macvtap on errors, from Jason
    Wang.

12) We don't set Kconfig symbol DEFAULT_TCP_CONG properly when the user
    selects BBR. Fix from Julian Wollrath.

13) Fix deadlock in transmit path on altera TSE driver, from Lino
    Sanfilippo.

14) Fix unbalanced reference counting in dsa_switch_tree, from Nikita
    Yushchenko.

15) tc_tunnel_key needs to be properly exported to userspace via uapi,
    fix from Roi Dayan.

16) rds_tcp_init_net() doesn't unregister notifier in error path, fix
    from Sowmini Varadhan.

17) Stale packet header pointer access after pskb_expand_head() in
    genenve driver, fix from Sabrina Dubroca.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (103 commits)
  net: avoid signed overflows for SO_{SND|RCV}BUFFORCE
  geneve: avoid use-after-free of skb->data
  tipc: check minimum bearer MTU
  net: renesas: ravb: unintialized return value
  sh_eth: remove unchecked interrupts for RZ/A1
  net: bcmgenet: Utilize correct struct device for all DMA operations
  NET: usb: qmi_wwan: add support for Telit LE922A PID 0x1040
  cdc_ether: Fix handling connection notification
  ip6_offload: check segs for NULL in ipv6_gso_segment.
  RDS: TCP: unregister_netdevice_notifier() in error path of rds_tcp_init_net
  Revert: "ip6_tunnel: Update skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit()"
  ipv6: Set skb->protocol properly for local output
  ipv4: Set skb->protocol properly for local output
  packet: fix race condition in packet_set_ring
  net: ethernet: altera: TSE: do not use tx queue lock in tx completion handler
  net: ethernet: altera: TSE: Remove unneeded dma sync for tx buffers
  net: ethernet: stmmac: fix of-node and fixed-link-phydev leaks
  net: ethernet: stmmac: platform: fix outdated function header
  net: ethernet: stmmac: dwmac-meson8b: fix probe error path
  net: ethernet: stmmac: dwmac-generic: fix probe error path
  ...

8 years agonet: avoid signed overflows for SO_{SND|RCV}BUFFORCE
Eric Dumazet [Fri, 2 Dec 2016 17:44:53 +0000 (09:44 -0800)]
net: avoid signed overflows for SO_{SND|RCV}BUFFORCE

CAP_NET_ADMIN users should not be allowed to set negative
sk_sndbuf or sk_rcvbuf values, as it can lead to various memory
corruptions, crashes, OOM...

Note that before commit 82981930125a ("net: cleanups in
sock_setsockopt()"), the bug was even more serious, since SO_SNDBUF
and SO_RCVBUF were vulnerable.

This needs to be backported to all known linux kernels.

Again, many thanks to syzkaller team for discovering this gem.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agogeneve: avoid use-after-free of skb->data
Sabrina Dubroca [Fri, 2 Dec 2016 15:49:29 +0000 (16:49 +0100)]
geneve: avoid use-after-free of skb->data

geneve{,6}_build_skb can end up doing a pskb_expand_head(), which
makes the ip_hdr(skb) reference we stashed earlier stale. Since it's
only needed as an argument to ip_tunnel_ecn_encap(), move this
directly in the function call.

Fixes: 08399efc6319 ("geneve: ensure ECN info is handled properly in all tx/rx paths")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agotipc: check minimum bearer MTU
Michal Kubeček [Fri, 2 Dec 2016 08:33:41 +0000 (09:33 +0100)]
tipc: check minimum bearer MTU

Qian Zhang (张谦) reported a potential socket buffer overflow in
tipc_msg_build() which is also known as CVE-2016-8632: due to
insufficient checks, a buffer overflow can occur if MTU is too short for
even tipc headers. As anyone can set device MTU in a user/net namespace,
this issue can be abused by a regular user.

As agreed in the discussion on Ben Hutchings' original patch, we should
check the MTU at the moment a bearer is attached rather than for each
processed packet. We also need to repeat the check when bearer MTU is
adjusted to new device MTU. UDP case also needs a check to avoid
overflow when calculating bearer MTU.

Fixes: b97bf3fd8f6a ("[TIPC] Initial merge")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reported-by: Qian Zhang (张谦) <zhangqian-c@360.cn>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoMerge tag 'linux-can-fixes-for-4.9-20161201' of git://git.kernel.org/pub/scm/linux...
David S. Miller [Fri, 2 Dec 2016 19:02:13 +0000 (14:02 -0500)]
Merge tag 'linux-can-fixes-for-4.9-20161201' of git://git./linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2016-12-02

this is a pull request for net/master.

There are two patches by Stephane Grosjean, who adds support for the new
PCAN-USB X6 USB interface to the pcan_usb driver.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: renesas: ravb: unintialized return value
Dan Carpenter [Thu, 1 Dec 2016 20:57:44 +0000 (23:57 +0300)]
net: renesas: ravb: unintialized return value

We want to set the other "err" variable here so that we can return it
later.  My version of GCC misses this issue but I caught it with a
static checker.

Fixes: 9f70eb339f52 ("net: ethernet: renesas: ravb: fix fixed-link phydev leaks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agosh_eth: remove unchecked interrupts for RZ/A1
Chris Brandt [Thu, 1 Dec 2016 18:32:14 +0000 (13:32 -0500)]
sh_eth: remove unchecked interrupts for RZ/A1

When streaming a lot of data and the RZ/A1 can't keep up, some status bits
will get set that are not being checked or cleared which cause the
following messages and the Ethernet driver to stop working. This
patch fixes that issue.

irq 21: nobody cared (try booting with the "irqpoll" option)
handlers:
[<c036b71c>] sh_eth_interrupt
Disabling IRQ #21

Fixes: db893473d313a4ad ("sh_eth: Add support for r7s72100")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: bcmgenet: Utilize correct struct device for all DMA operations
Florian Fainelli [Thu, 1 Dec 2016 17:45:45 +0000 (09:45 -0800)]
net: bcmgenet: Utilize correct struct device for all DMA operations

__bcmgenet_tx_reclaim() and bcmgenet_free_rx_buffers() are not using the
same struct device during unmap that was used for the map operation,
which makes DMA-API debugging warn about it. Fix this by always using
&priv->pdev->dev throughout the driver, using an identical device
reference for all map/unmap calls.

Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoFix up a couple of field names in the CREDITS file
Linus Torvalds [Fri, 2 Dec 2016 18:48:50 +0000 (10:48 -0800)]
Fix up a couple of field names in the CREDITS file

Ozgur Karatas reported that the very first entry in the CREDITS file had
the wrong tag for name (M: instead of N: - it happened when moving the
entry from the MAINTAINERS file, where 'M:' stands for "Maintainer").

And when I went looking, I found a couple of other cases of wrong
tagging too.

Reported-by: Ozgur Karatas <mueddib@yandex.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8 years agoNET: usb: qmi_wwan: add support for Telit LE922A PID 0x1040
Daniele Palmas [Thu, 1 Dec 2016 15:52:05 +0000 (16:52 +0100)]
NET: usb: qmi_wwan: add support for Telit LE922A PID 0x1040

This patch adds support for PID 0x1040 of Telit LE922A.

The qmi adapter requires to have DTR set for proper working,
so QMI_WWAN_QUIRK_DTR has been enabled.

Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agocdc_ether: Fix handling connection notification
Kristian Evensen [Thu, 1 Dec 2016 13:23:17 +0000 (14:23 +0100)]
cdc_ether: Fix handling connection notification

Commit bfe9b9d2df66 ("cdc_ether: Improve ZTE MF823/831/910 handling")
introduced a work-around in usbnet_cdc_status() for devices that exported
cdc carrier on twice on connect. Before the commit, this behavior caused
the link state to be incorrect. It was assumed that all CDC Ethernet
devices would either export this behavior, or send one off and then one on
notification (which seems to be the default behavior).

Unfortunately, it turns out multiple devices sends a connection
notification multiple times per second (via an interrupt), even when
connection state does not change. This has been observed with several
different USB LAN dongles (at least), for example 13b1:0041 (Linksys).
After bfe9b9d2df66, the link state has been set as down and then up for
each notification. This has caused a flood of Netlink NEWLINK messages and
syslog to be flooded with messages similar to:

cdc_ether 2-1:2.0 eth1: kevent 12 may have been dropped

This commit fixes the behavior by reverting usbnet_cdc_status() to how it
was before bfe9b9d2df66. The work-around has been moved to a separate
status-function which is only called when a known, affect device is
detected.

v1->v2:

* Do not open-code netif_carrier_ok() (thanks Henning Schild).
* Call netif_carrier_off() instead of usb_link_change(). This prevents
calling schedule_work() twice without giving the work queue a chance to be
processed (thanks Bjørn Mork).

Fixes: bfe9b9d2df66 ("cdc_ether: Improve ZTE MF823/831/910 handling")
Reported-by: Henning Schild <henning.schild@siemens.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoip6_offload: check segs for NULL in ipv6_gso_segment.
Artem Savkov [Thu, 1 Dec 2016 13:06:04 +0000 (14:06 +0100)]
ip6_offload: check segs for NULL in ipv6_gso_segment.

segs needs to be checked for being NULL in ipv6_gso_segment() before calling
skb_shinfo(segs), otherwise kernel can run into a NULL-pointer dereference:

[   97.811262] BUG: unable to handle kernel NULL pointer dereference at 00000000000000cc
[   97.819112] IP: [<ffffffff816e52f9>] ipv6_gso_segment+0x119/0x2f0
[   97.825214] PGD 0 [   97.827047]
[   97.828540] Oops: 0000 [#1] SMP
[   97.831678] Modules linked in: vhost_net vhost macvtap macvlan nfsv3 rpcsec_gss_krb5
nfsv4 dns_resolver nfs fscache xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4
iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack
ipt_REJECT nf_reject_ipv4 tun ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter
bridge stp llc snd_hda_codec_realtek snd_hda_codec_hdmi snd_hda_codec_generic snd_hda_intel
snd_hda_codec edac_mce_amd snd_hda_core edac_core snd_hwdep kvm_amd snd_seq kvm snd_seq_device
snd_pcm irqbypass snd_timer ppdev parport_serial snd parport_pc k10temp pcspkr soundcore parport
sp5100_tco shpchp sg wmi i2c_piix4 acpi_cpufreq nfsd auth_rpcgss nfs_acl lockd grace sunrpc
ip_tables xfs libcrc32c sr_mod cdrom sd_mod ata_generic pata_acpi amdkfd amd_iommu_v2 radeon
broadcom bcm_phy_lib i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops
ttm ahci serio_raw tg3 firewire_ohci libahci pata_atiixp drm ptp libata firewire_core pps_core
i2c_core crc_itu_t fjes dm_mirror dm_region_hash dm_log dm_mod
[   97.927721] CPU: 1 PID: 3504 Comm: vhost-3495 Not tainted 4.9.0-7.el7.test.x86_64 #1
[   97.935457] Hardware name: AMD Snook/Snook, BIOS ESK0726A 07/26/2010
[   97.941806] task: ffff880129a1c080 task.stack: ffffc90001bcc000
[   97.947720] RIP: 0010:[<ffffffff816e52f9>]  [<ffffffff816e52f9>] ipv6_gso_segment+0x119/0x2f0
[   97.956251] RSP: 0018:ffff88012fc43a10  EFLAGS: 00010207
[   97.961557] RAX: 0000000000000000 RBX: ffff8801292c8700 RCX: 0000000000000594
[   97.968687] RDX: 0000000000000593 RSI: ffff880129a846c0 RDI: 0000000000240000
[   97.975814] RBP: ffff88012fc43a68 R08: ffff880129a8404e R09: 0000000000000000
[   97.982942] R10: 0000000000000000 R11: ffff880129a84076 R12: 00000020002949b3
[   97.990070] R13: ffff88012a580000 R14: 0000000000000000 R15: ffff88012a580000
[   97.997198] FS:  0000000000000000(0000) GS:ffff88012fc40000(0000) knlGS:0000000000000000
[   98.005280] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   98.011021] CR2: 00000000000000cc CR3: 0000000126c5d000 CR4: 00000000000006e0
[   98.018149] Stack:
[   98.020157]  00000000ffffffff ffff88012fc43ac8 ffffffffa017ad0a 000000000000000e
[   98.027584]  0000001300000000 0000000077d59998 ffff8801292c8700 00000020002949b3
[   98.035010]  ffff88012a580000 0000000000000000 ffff88012a580000 ffff88012fc43a98
[   98.042437] Call Trace:
[   98.044879]  <IRQ> [   98.046803]  [<ffffffffa017ad0a>] ? tg3_start_xmit+0x84a/0xd60 [tg3]
[   98.053156]  [<ffffffff815eeee0>] skb_mac_gso_segment+0xb0/0x130
[   98.059158]  [<ffffffff815eefd3>] __skb_gso_segment+0x73/0x110
[   98.064985]  [<ffffffff815ef40d>] validate_xmit_skb+0x12d/0x2b0
[   98.070899]  [<ffffffff815ef5d2>] validate_xmit_skb_list+0x42/0x70
[   98.077073]  [<ffffffff81618560>] sch_direct_xmit+0xd0/0x1b0
[   98.082726]  [<ffffffff815efd86>] __dev_queue_xmit+0x486/0x690
[   98.088554]  [<ffffffff8135c135>] ? cpumask_next_and+0x35/0x50
[   98.094380]  [<ffffffff815effa0>] dev_queue_xmit+0x10/0x20
[   98.099863]  [<ffffffffa09ce057>] br_dev_queue_push_xmit+0xa7/0x170 [bridge]
[   98.106907]  [<ffffffffa09ce161>] br_forward_finish+0x41/0xc0 [bridge]
[   98.113430]  [<ffffffff81627cf2>] ? nf_iterate+0x52/0x60
[   98.118735]  [<ffffffff81627d6b>] ? nf_hook_slow+0x6b/0xc0
[   98.124216]  [<ffffffffa09ce32c>] __br_forward+0x14c/0x1e0 [bridge]
[   98.130480]  [<ffffffffa09ce120>] ? br_dev_queue_push_xmit+0x170/0x170 [bridge]
[   98.137785]  [<ffffffffa09ce4bd>] br_forward+0x9d/0xb0 [bridge]
[   98.143701]  [<ffffffffa09cfbb7>] br_handle_frame_finish+0x267/0x560 [bridge]
[   98.150834]  [<ffffffffa09d0064>] br_handle_frame+0x174/0x2f0 [bridge]
[   98.157355]  [<ffffffff8102fb89>] ? sched_clock+0x9/0x10
[   98.162662]  [<ffffffff810b63b2>] ? sched_clock_cpu+0x72/0xa0
[   98.168403]  [<ffffffff815eccf5>] __netif_receive_skb_core+0x1e5/0xa20
[   98.174926]  [<ffffffff813659f9>] ? timerqueue_add+0x59/0xb0
[   98.180580]  [<ffffffff815ed548>] __netif_receive_skb+0x18/0x60
[   98.186494]  [<ffffffff815ee625>] process_backlog+0x95/0x140
[   98.192145]  [<ffffffff815edccd>] net_rx_action+0x16d/0x380
[   98.197713]  [<ffffffff8170cff1>] __do_softirq+0xd1/0x283
[   98.203106]  [<ffffffff8170b2bc>] do_softirq_own_stack+0x1c/0x30
[   98.209107]  <EOI> [   98.211029]  [<ffffffff8108a5c0>] do_softirq+0x50/0x60
[   98.216166]  [<ffffffff815ec853>] netif_rx_ni+0x33/0x80
[   98.221386]  [<ffffffffa09eeff7>] tun_get_user+0x487/0x7f0 [tun]
[   98.227388]  [<ffffffffa09ef3ab>] tun_sendmsg+0x4b/0x60 [tun]
[   98.233129]  [<ffffffffa0b68932>] handle_tx+0x282/0x540 [vhost_net]
[   98.239392]  [<ffffffffa0b68c25>] handle_tx_kick+0x15/0x20 [vhost_net]
[   98.245916]  [<ffffffffa0abacfe>] vhost_worker+0x9e/0xf0 [vhost]
[   98.251919]  [<ffffffffa0abac60>] ? vhost_umem_alloc+0x40/0x40 [vhost]
[   98.258440]  [<ffffffff81003a47>] ? do_syscall_64+0x67/0x180
[   98.264094]  [<ffffffff810a44d9>] kthread+0xd9/0xf0
[   98.268965]  [<ffffffff810a4400>] ? kthread_park+0x60/0x60
[   98.274444]  [<ffffffff8170a4d5>] ret_from_fork+0x25/0x30
[   98.279836] Code: 8b 93 d8 00 00 00 48 2b 93 d0 00 00 00 4c 89 e6 48 89 df 66 89 93 c2 00 00 00 ff 10 48 3d 00 f0 ff ff 49 89 c2 0f 87 52 01 00 00 <41> 8b 92 cc 00 00 00 48 8b 80 d0 00 00 00 44 0f b7 74 10 06 66
[   98.299425] RIP  [<ffffffff816e52f9>] ipv6_gso_segment+0x119/0x2f0
[   98.305612]  RSP <ffff88012fc43a10>
[   98.309094] CR2: 00000000000000cc
[   98.312406] ---[ end trace 726a2c7a2d2d78d0 ]---

Signed-off-by: Artem Savkov <asavkov@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoMAINTAINERS: add etnaviv mailinglist
Lucas Stach [Fri, 2 Dec 2016 12:04:01 +0000 (13:04 +0100)]
MAINTAINERS: add etnaviv mailinglist

The etnaviv project now has its own mailinglist, add it to the
MAINTAINERS file, so kernel patches get CC'ed to it.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
8 years agodrm/etnaviv: move linear window on MC1.0 parts if necessary
Lucas Stach [Fri, 2 Dec 2016 11:19:16 +0000 (12:19 +0100)]
drm/etnaviv: move linear window on MC1.0 parts if necessary

On i.MX6SX the physical memory is placed above the 2GB mark, so the GPU
linear window has to be moved for the GPU to work at all. This doesn't
mix with the FAST_CLEAR feature, as the TS unit doesn't take the linear
window offset into account and will corrupt memory when used with a
non-zero offset.

Move the linear window if it's necessary for the GPU to work, but avoid
announcing FAST_CLEAR support to userspace in this case.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de>
8 years agodrm/etnaviv: don't invoke OOM killer from dump code
Lucas Stach [Fri, 2 Dec 2016 10:14:13 +0000 (11:14 +0100)]
drm/etnaviv: don't invoke OOM killer from dump code

The dumper is only a debugging aid so we don't want to invoke the OOM
killer if buffer for the potentially large GPU state can't be vmalloced.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
8 years agodrm/etnaviv: fix gem_prime_get_sg_table to return new SG table
Lucas Stach [Wed, 30 Nov 2016 14:26:26 +0000 (15:26 +0100)]
drm/etnaviv: fix gem_prime_get_sg_table to return new SG table

The object internal SG table must not be returned, as the caller
will take ownership of the returned table.

Construct a new table from the object pages and return this one
instead.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
8 years agodrm/etnaviv: Allow DRAW_INSTANCED commands
Wladimir J. van der Laan [Fri, 11 Nov 2016 16:57:54 +0000 (17:57 +0100)]
drm/etnaviv: Allow DRAW_INSTANCED commands

Vivante GPUs with HALTI0 feature support a DRAW_INSTANCED command in the
command stream to draw a number of instances of the same geometry.

The information that has been figured out about the command can be found
here: https://github.com/etnaviv/etna_viv/blob/master/rnndb/cmdstream.xml#L270

This command is not allowed currently by the DRM driver because it
was not known before. This patch enables parsing it in command
streams and allows using it by userspace drivers.

Signed-off-by: Wladimir J. van der Laan <laanwj@gmail.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
8 years agodrm/etnaviv: implement dma-buf mmap
Lucas Stach [Fri, 18 Nov 2016 14:15:16 +0000 (15:15 +0100)]
drm/etnaviv: implement dma-buf mmap

This adds the required boilerplate to allow direct mmap of exported
etnaviv BOs.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
8 years agoRDS: TCP: unregister_netdevice_notifier() in error path of rds_tcp_init_net
Sowmini Varadhan [Thu, 1 Dec 2016 12:44:43 +0000 (04:44 -0800)]
RDS: TCP: unregister_netdevice_notifier() in error path of rds_tcp_init_net

If some error is encountered in rds_tcp_init_net, make sure to
unregister_netdevice_notifier(), else we could trigger a panic
later on, when the modprobe from a netns fails.

Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoRevert: "ip6_tunnel: Update skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit()"
Eli Cooper [Thu, 1 Dec 2016 02:05:12 +0000 (10:05 +0800)]
Revert: "ip6_tunnel: Update skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit()"

This reverts commit ae148b085876fa771d9ef2c05f85d4b4bf09ce0d
("ip6_tunnel: Update skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit()").

skb->protocol is now set in __ip_local_out() and __ip6_local_out() before
dst_output() is called. It is no longer necessary to do it for each tunnel.

Cc: stable@vger.kernel.org
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoipv6: Set skb->protocol properly for local output
Eli Cooper [Thu, 1 Dec 2016 02:05:11 +0000 (10:05 +0800)]
ipv6: Set skb->protocol properly for local output

When xfrm is applied to TSO/GSO packets, it follows this path:

    xfrm_output() -> xfrm_output_gso() -> skb_gso_segment()

where skb_gso_segment() relies on skb->protocol to function properly.

This patch sets skb->protocol to ETH_P_IPV6 before dst_output() is called,
fixing a bug where GSO packets sent through an ipip6 tunnel are dropped
when xfrm is involved.

Cc: stable@vger.kernel.org
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoipv4: Set skb->protocol properly for local output
Eli Cooper [Thu, 1 Dec 2016 02:05:10 +0000 (10:05 +0800)]
ipv4: Set skb->protocol properly for local output

When xfrm is applied to TSO/GSO packets, it follows this path:

    xfrm_output() -> xfrm_output_gso() -> skb_gso_segment()

where skb_gso_segment() relies on skb->protocol to function properly.

This patch sets skb->protocol to ETH_P_IP before dst_output() is called,
fixing a bug where GSO packets sent through a sit tunnel are dropped
when xfrm is involved.

Cc: stable@vger.kernel.org
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agopacket: fix race condition in packet_set_ring
Philip Pettersson [Wed, 30 Nov 2016 22:55:36 +0000 (14:55 -0800)]
packet: fix race condition in packet_set_ring

When packet_set_ring creates a ring buffer it will initialize a
struct timer_list if the packet version is TPACKET_V3. This value
can then be raced by a different thread calling setsockopt to
set the version to TPACKET_V1 before packet_set_ring has finished.

This leads to a use-after-free on a function pointer in the
struct timer_list when the socket is closed as the previously
initialized timer will not be deleted.

The bug is fixed by taking lock_sock(sk) in packet_setsockopt when
changing the packet version while also taking the lock at the start
of packet_set_ring.

Fixes: f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer implementation.")
Signed-off-by: Philip Pettersson <philip.pettersson@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoMerge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Linus Torvalds [Fri, 2 Dec 2016 17:15:26 +0000 (09:15 -0800)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm

Pull KVM fixes from Radim Krčmář:
 "All architectures avoid memory corruption in an error path. ARM
  prevents bogus acknowledgement of interrupts"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: use after free in kvm_ioctl_create_device()
  KVM: arm/arm64: vgic: Don't notify EOI for non-SPIs

8 years agoMerge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa...
Linus Torvalds [Fri, 2 Dec 2016 17:12:44 +0000 (09:12 -0800)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux

Pull i2c fix from Wolfram Sang:
 "Here is the revert for the regression of the i2c-octeon driver I
  mentioned last time. I wished for a bit more feedback, but all people
  working actively on it are in need of this patch, so here it goes"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  Revert "i2c: octeon: thunderx: Limit register access retries"

8 years agonet: ethernet: altera: TSE: do not use tx queue lock in tx completion handler
Lino Sanfilippo [Wed, 30 Nov 2016 22:48:32 +0000 (23:48 +0100)]
net: ethernet: altera: TSE: do not use tx queue lock in tx completion handler

The driver already uses its private lock for synchronization between xmit
and xmit completion handler making the additional use of the xmit_lock
unnecessary.
Furthermore the driver does not set NETIF_F_LLTX resulting in xmit to be
called with the xmit_lock held and then taking the private lock while xmit
completion handler does the reverse, first take the private lock, then the
xmit_lock.
Fix these issues by not taking the xmit_lock in the tx completion handler.

Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: altera: TSE: Remove unneeded dma sync for tx buffers
Lino Sanfilippo [Wed, 30 Nov 2016 22:48:31 +0000 (23:48 +0100)]
net: ethernet: altera: TSE: Remove unneeded dma sync for tx buffers

An explicit dma sync for device directly after mapping as well as an
explicit dma sync for cpu directly before unmapping is unnecessary and
costly on the hotpath. So remove these calls.

Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agodefault exported asm symbols to zero
Arnd Bergmann [Fri, 2 Dec 2016 12:40:27 +0000 (13:40 +0100)]
default exported asm symbols to zero

With binutils-2.26 and before, a weak missing symbol was kept during the
final link, and a missing CRC for an export would lead to that CRC being
treated as zero implicitly.  With binutils-2.27, the crc symbol gets
dropped, and any module trying to use it will fail to load.

This sets the weak CRC symbol to zero explicitly, making it defined in
vmlinux, which in turn lets us load the modules referring to that CRC.

The comment above the __CRC_SYMBOL macro suggests that this was always
the intention, although it also seems that all symbols defined in C have
a correct CRC these days, and only the exports that are now done in
assembly need this.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Adam Borowski <kilobyte@angband.pl>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8 years agoarm64: dts: juno: fix cluster sleep state entry latency on all SoC versions
Sudeep Holla [Wed, 16 Nov 2016 17:31:31 +0000 (17:31 +0000)]
arm64: dts: juno: fix cluster sleep state entry latency on all SoC versions

The core and the cluster sleep state entry latencies can't be same as
cluster sleep involves more work compared to core level e.g. shared
cache maintenance.

Experiments have shown on an average about 100us more latency for the
cluster sleep state compared to the core level sleep. This patch fixes
the entry latency for the cluster sleep state.

Fixes: 28e10a8f3a03 ("arm64: dts: juno: Add idle-states to device tree")
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: "Jon Medhurst (Tixy)" <tixy@linaro.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
8 years agoMerge branch 'stmmac-probe-error-handling-and-phydev-leaks'
David S. Miller [Fri, 2 Dec 2016 15:42:47 +0000 (10:42 -0500)]
Merge branch 'stmmac-probe-error-handling-and-phydev-leaks'

Johan Hovold says:

====================
net: stmmac: fix probe error handling and phydev leaks

This series fixes a number of issues with the stmmac-driver probe error
handling, which for example left clocks enabled after probe failures.

The final patch fixes a failure to deregister and free any fixed-link
PHYs that were registered during probe on probe errors and on driver
unbind. It also fixes a related of-node leak on late probe errors.

This series depends on the of_phy_deregister_fixed_link() helper that
was just merged to net.

As mentioned earlier, one staging driver also suffers from a similar
leak and can be fixed up once the above mentioned helper hits mainline.

Note that these patches have only been compile tested.
====================

Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: stmmac: fix of-node and fixed-link-phydev leaks
Johan Hovold [Wed, 30 Nov 2016 14:29:55 +0000 (15:29 +0100)]
net: ethernet: stmmac: fix of-node and fixed-link-phydev leaks

Make sure to deregister and free any fixed-link phy registered during
probe on probe errors and on driver unbind by adding a new glue helper
function.

Drop the of-node reference taken in the same path also on late probe
errors (and not just on driver unbind) by moving the put from
stmmac_dvr_remove() to the new helper.

Fixes: 277323814e49 ("stmmac: add fixed-link device-tree support")
Fixes: 4613b279bee7 ("ethernet: stmicro: stmmac: add missing of_node_put
after calling of_parse_phandle")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: stmmac: platform: fix outdated function header
Johan Hovold [Wed, 30 Nov 2016 14:29:54 +0000 (15:29 +0100)]
net: ethernet: stmmac: platform: fix outdated function header

Fix the OF-helper function header to reflect that the function no longer
has a platform-data parameter.

Fixes: b0003ead75f3 ("stmmac: make stmmac_probe_config_dt return the
platform data struct")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: stmmac: dwmac-meson8b: fix probe error path
Johan Hovold [Wed, 30 Nov 2016 14:29:53 +0000 (15:29 +0100)]
net: ethernet: stmmac: dwmac-meson8b: fix probe error path

Make sure to disable clocks before returning on late probe errors.

Fixes: 566e82516253 ("net: stmmac: add a glue driver for the Amlogic
Meson 8b / GXBB DWMAC")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: stmmac: dwmac-generic: fix probe error path
Johan Hovold [Wed, 30 Nov 2016 14:29:52 +0000 (15:29 +0100)]
net: ethernet: stmmac: dwmac-generic: fix probe error path

Make sure to call any exit() callback to undo the effect of init()
before returning on late probe errors.

Fixes: cf3f047b9af4 ("stmmac: move hw init in the probe (v2)")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: stmmac: dwmac-rk: fix probe error path
Johan Hovold [Wed, 30 Nov 2016 14:29:51 +0000 (15:29 +0100)]
net: ethernet: stmmac: dwmac-rk: fix probe error path

Make sure to disable runtime PM, power down the PHY, and disable clocks
before returning on late probe errors.

Fixes: 27ffefd2d109 ("stmmac: dwmac-rk: create a new probe function")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: stmmac: dwmac-sti: fix probe error path
Johan Hovold [Wed, 30 Nov 2016 14:29:50 +0000 (15:29 +0100)]
net: ethernet: stmmac: dwmac-sti: fix probe error path

Make sure to disable clocks before returning on late probe errors.

Fixes: 8387ee21f972 ("stmmac: dwmac-sti: turn setup callback into a
probe function")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: stmmac: dwmac-socfpga: fix use-after-free on probe errors
Johan Hovold [Wed, 30 Nov 2016 14:29:49 +0000 (15:29 +0100)]
net: ethernet: stmmac: dwmac-socfpga: fix use-after-free on probe errors

Make sure to call stmmac_dvr_remove() before returning on late probe
errors so that memory is freed, clocks are disabled, and the netdev is
deregistered before its resources go away.

Fixes: 3c201b5a84ed ("net: stmmac: socfpga: Remove re-registration of
reset controller")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet/rtnetlink: fix attribute name in nlmsg_size() comments
Tobias Klauser [Wed, 30 Nov 2016 13:30:37 +0000 (14:30 +0100)]
net/rtnetlink: fix attribute name in nlmsg_size() comments

Use the correct attribute constant names IFLA_GSO_MAX_{SEGS,SIZE}
instead of IFLA_MAX_GSO_{SEGS,SIZE} for the comments int nlmsg_size().

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoMerge tag 'pci-v4.9-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Linus Torvalds [Fri, 2 Dec 2016 00:44:42 +0000 (16:44 -0800)]
Merge tag 'pci-v4.9-fixes-4' of git://git./linux/kernel/git/helgaas/pci

Pull PCI fixes from Bjorn Helgaas:
 "PCI fixes:

   - Fix Read Completion Boundary setting, which fixes a boot failure on
     IBM x3850 with Mellanox MT27500 ConnectX-3

   - Update some MAINTAINERS entries and email addresses"

* tag 'pci-v4.9-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Set Read Completion Boundary to 128 iff Root Port supports it (_HPX)
  PCI: Export pcie_find_root_port
  PCI: designware-plat: Update author email
  PCI: designware: Change maintainer to Joao Pinto
  MAINTAINERS: Add devicetree binding to PCI i.MX6 entry
  MAINTAINERS: Update Richard Zhu's email address

8 years agoixgbe/ixgbevf: Don't use lco_csum to compute IPv4 checksum
Alexander Duyck [Mon, 28 Nov 2016 15:42:29 +0000 (10:42 -0500)]
ixgbe/ixgbevf: Don't use lco_csum to compute IPv4 checksum

In the case of IPIP and SIT tunnel frames the outer transport header
offset is actually set to the same offset as the inner transport header.
This results in the lco_csum call not doing any checksum computation over
the inner IPv4/v6 header data.

In order to account for that I am updating the code so that we determine
the location to start the checksum ourselves based on the location of the
IPv4 header and the length.

Fixes: b83e30104bd9 ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoigb/igbvf: Don't use lco_csum to compute IPv4 checksum
Alexander Duyck [Mon, 28 Nov 2016 15:42:23 +0000 (10:42 -0500)]
igb/igbvf: Don't use lco_csum to compute IPv4 checksum

In the case of IPIP and SIT tunnel frames the outer transport header
offset is actually set to the same offset as the inner transport header.
This results in the lco_csum call not doing any checksum computation over
the inner IPv4/v6 header data.

In order to account for that I am updating the code so that we determine
the location to start the checksum ourselves based on the location of the
IPv4 header and the length.

Fixes: e10715d3e961 ("igb/igbvf: Add support for GSO partial")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: asix: Fix AX88772_suspend() USB vendor commands failure issues
allan [Wed, 30 Nov 2016 08:29:08 +0000 (16:29 +0800)]
net: asix: Fix AX88772_suspend() USB vendor commands failure issues

The change fixes AX88772_suspend() USB vendor commands failure issues.

Signed-off-by: Allan Chou <allan@asix.com.tw>
Tested-by: Allan Chou <allan@asix.com.tw>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoMerge branch 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszer...
Linus Torvalds [Thu, 1 Dec 2016 18:31:53 +0000 (10:31 -0800)]
Merge branch 'overlayfs-linus' of git://git./linux/kernel/git/mszeredi/vfs

Pull overlayfs fix from Miklos Szeredi:
 "This fixes a regression introduced in 4.8"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: fix d_real() for stacked fs

8 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Linus Torvalds [Thu, 1 Dec 2016 18:29:41 +0000 (10:29 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

Pull input fixes from Dmitry Torokhov: "We are disabling automatic
  probing of BYD touchpads as it results in too many false positives,
  and the hardware is not terribly popular and having the protocol
  support does not result in significantly improved user experience.

  We also change keycode for KEY_DATA to avoid clashing with
  KEY_FASTREVERSE. Luckily this newish code is used by CEC framework
  that is still in staging, so it is extremely unlikely that someone has
  already started using this keycode"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: change KEY_DATA from 0x275 to 0x277
  Input: psmouse - disable automatic probing of BYD touchpads

8 years agokbuild: make sure autoksyms.h exists early
Nicolas Pitre [Wed, 30 Nov 2016 22:41:58 +0000 (17:41 -0500)]
kbuild: make sure autoksyms.h exists early

Some people are able to trigger a race where autoksyms.h is used before
its empty version is even created.  Let's create it at the same time as
the directory holding it is created.

Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Prarit Bhargava <prarit@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
David S. Miller [Thu, 1 Dec 2016 16:35:49 +0000 (11:35 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/klassert/ipsec

Steffen Klassert says:

====================
pull request (net): ipsec 2016-12-01

1) Change the error value when someone tries to run 32bit
   userspace on a 64bit host from -ENOTSUPP to the userspace
   exported -EOPNOTSUPP. Fix from Yi Zhao.

2) On inbound, ESN sequence numbers are already in network
   byte order. So don't try to convert it again, this fixes
   integrity verification for ESN. Fixes from Tobias Brunner.

Please pull or let me know if there are problems.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf
David S. Miller [Thu, 1 Dec 2016 16:04:41 +0000 (11:04 -0500)]
Merge git://git./pub/scm/linux/kernel/git/pablo/nf

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

This is a large batch of Netfilter fixes for net, they are:

1) Three patches to fix NAT conversion to rhashtable: Switch to rhlist
   structure that allows to have several objects with the same key.
   Moreover, fix wrong comparison logic in nf_nat_bysource_cmp() as this is
   expecting a return value similar to memcmp(). Change location of
   the nat_bysource field in the nf_conn structure to avoid zeroing
   this as it breaks interaction with SLAB_DESTROY_BY_RCU and lead us
   to crashes. From Florian Westphal.

2) Don't allow malformed fragments go through in IPv6, drop them,
   otherwise we hit GPF, patch from Florian Westphal.

3) Fix crash if attributes are missing in nft_range, from Liping Zhang.

4) Fix arptables 32-bits userspace 64-bits kernel compat, from Hongxu Jia.

5) Two patches from David Ahern to fix netfilter interaction with vrf.
   From David Ahern.

6) Fix element timeout calculation in nf_tables, we take milliseconds
   from userspace, but we use jiffies from kernelspace. Patch from
   Anders K.  Pedersen.

7) Missing validation length netlink attribute for nft_hash, from
   Laura Garcia.

8) Fix nf_conntrack_helper documentation, we don't default to off
   anymore for a bit of time so let's get this in sync with the code.

I know is late but I think these are important, specifically the NAT
bits, as they are mostly addressing fallout from recent changes. I also
read there are chances to have -rc8, if that is the case, that would
also give us a bit more time to test this.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agoKVM: use after free in kvm_ioctl_create_device()
Dan Carpenter [Wed, 30 Nov 2016 19:21:05 +0000 (22:21 +0300)]
KVM: use after free in kvm_ioctl_create_device()

We should move the ops->destroy(dev) after the list_del(&dev->vm_node)
so that we don't use "dev" after freeing it.

Fixes: a28ebea2adc4 ("KVM: Protect device ops->create and list_add with kvm->lock")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
8 years agoMerge tag 'kvm-arm-for-4.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git...
Radim Krčmář [Thu, 1 Dec 2016 13:56:34 +0000 (14:56 +0100)]
Merge tag 'kvm-arm-for-4.9-rc7' of git://git./linux/kernel/git/kvmarm/kvmarm

KVM/ARM updates for v4.9-rc7

- Do not call kvm_notify_acked for PPIs

8 years agocan: peak: Add support for PCAN-USB X6 USB interface
Stephane Grosjean [Thu, 1 Dec 2016 10:41:12 +0000 (11:41 +0100)]
can: peak: Add support for PCAN-USB X6 USB interface

This adds support for PEAK-System PCAN-USB X6 USB to CAN interface.

The CAN FD adapter PCAN-USB X6 allows the connection of up to 6 CAN FD
or CAN networks to a computer via USB. The interface is installed in an
aluminum profile casing and is shipped in versions with D-Sub connectors
or M12 circular connectors.

The PCAN-USB X6 registers in the USB sub-system as if 3x PCAN-USB-Pro FD
adapters were plugged. So, this patch:

- updates the PEAK_USB entry of the corresponding Kconfig file
- defines and adds the device id. of the PCAN-USB X6 (0x0014) into the
  table of supported device ids
- defines and adds the new software structure implementing the PCAN-USB X6,
  which is obviously a clone of the software structure implementing the
  PCAN-USB Pro FD.

Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
8 years agocan: peak: Fix bittiming fields size in bits
Stephane Grosjean [Thu, 1 Dec 2016 10:41:11 +0000 (11:41 +0100)]
can: peak: Fix bittiming fields size in bits

This fixes the bitimings fields ranges supported by all the CAN-FD USB
interfaces of the PEAK-System CAN-FD adapters.

Very first development versions of the IP core API defined smaller TSGEx
and SJW fields for both nominal and data bittimings records than the
production versions. This patch fixes them by enlarging their sizes to
the actual values:

field:           old size:    fixed size:
nominal TSGEG1   6            8
nominal TSGEG2   4            7
nominal SJW      4            7
data TSGEG1      4            5
data TSGEG2      3            4
data SJW         2            4

Note that this has no other consequences than offering larger choice to
bitrate encoding.

Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
8 years agoMerge branch 'akpm' (patches from Andrew)
Linus Torvalds [Thu, 1 Dec 2016 00:33:41 +0000 (16:33 -0800)]
Merge branch 'akpm' (patches from Andrew)

Merge misc fixes from Andrew Morton:
 "7 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm: fix false-positive WARN_ON() in truncate/invalidate for hugetlb
  kasan: support use-after-scope detection
  kasan: update kasan_global for gcc 7
  lib/debugobjects: export for use in modules
  zram: fix unbalanced idr management at hot removal
  thp: fix corner case of munlock() of PTE-mapped THPs
  mm, thp: propagation of conditional compilation in khugepaged.c

8 years agomm: fix false-positive WARN_ON() in truncate/invalidate for hugetlb
Kirill A. Shutemov [Wed, 30 Nov 2016 23:54:19 +0000 (15:54 -0800)]
mm: fix false-positive WARN_ON() in truncate/invalidate for hugetlb

Hugetlb pages have ->index in size of the huge pages (PMD_SIZE or
PUD_SIZE), not in PAGE_SIZE as other types of pages.  This means we
cannot user page_to_pgoff() to check whether we've got the right page
for the radix-tree index.

Let's introduce page_to_index() which would return radix-tree index for
given page.

We will be able to get rid of this once hugetlb will be switched to
multi-order entries.

Fixes: fc127da085c2 ("truncate: handle file thp")
Link: http://lkml.kernel.org/r/20161123093053.mjbnvn5zwxw5e6lk@black.fi.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Doug Nelson <doug.nelson@intel.com>
Tested-by: Doug Nelson <doug.nelson@intel.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: <stable@vger.kernel.org> [4.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8 years agokasan: support use-after-scope detection
Dmitry Vyukov [Wed, 30 Nov 2016 23:54:16 +0000 (15:54 -0800)]
kasan: support use-after-scope detection

Gcc revision 241896 implements use-after-scope detection.  Will be
available in gcc 7.  Support it in KASAN.

Gcc emits 2 new callbacks to poison/unpoison large stack objects when
they go in/out of scope.  Implement the callbacks and add a test.

[dvyukov@google.com: v3]
Link: http://lkml.kernel.org/r/1479998292-144502-1-git-send-email-dvyukov@google.com
Link: http://lkml.kernel.org/r/1479226045-145148-1-git-send-email-dvyukov@google.com
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: <stable@vger.kernel.org> [4.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8 years agokasan: update kasan_global for gcc 7
Dmitry Vyukov [Wed, 30 Nov 2016 23:54:13 +0000 (15:54 -0800)]
kasan: update kasan_global for gcc 7

kasan_global struct is part of compiler/runtime ABI.  gcc revision
241983 has added a new field to kasan_global struct.  Update kernel
definition of kasan_global struct to include the new field.

Without this patch KASAN is broken with gcc 7.

Link: http://lkml.kernel.org/r/1479219743-28682-1-git-send-email-dvyukov@google.com
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: <stable@vger.kernel.org> [4.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8 years agolib/debugobjects: export for use in modules
Chris Wilson [Wed, 30 Nov 2016 23:54:10 +0000 (15:54 -0800)]
lib/debugobjects: export for use in modules

Drivers, or other modules, that use a mixture of objects (especially
objects embedded within other objects) would like to take advantage of
the debugobjects facilities to help catch misuse.  Currently, the
debugobjects interface is only available to builtin drivers and requires
a set of EXPORT_SYMBOL_GPL for use by modules.

I am using the debugobjects in i915.ko to try and catch some invalid
operations on embedded objects.  The problem currently only presents
itself across module unload so forcing i915 to be builtin is not an
option.

Link: http://lkml.kernel.org/r/20161122143039.6433-1-chris@chris-wilson.co.uk
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Du, Changbin" <changbin.du@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8 years agozram: fix unbalanced idr management at hot removal
Takashi Iwai [Wed, 30 Nov 2016 23:54:08 +0000 (15:54 -0800)]
zram: fix unbalanced idr management at hot removal

The zram hot removal code calls idr_remove() even when zram_remove()
returns an error (typically -EBUSY).  This results in a leftover at the
device release, eventually leading to a crash when the module is
reloaded.

As described in the bug report below, the following procedure would
cause an Oops with zram:

 - provision three zram devices via modprobe zram num_devices=3
 - configure a size for each device
   + echo "1G" > /sys/block/$zram_name/disksize
 - mkfs and mount zram0 only
 - attempt to hot remove all three devices
   + echo 2 > /sys/class/zram-control/hot_remove
   + echo 1 > /sys/class/zram-control/hot_remove
   + echo 0 > /sys/class/zram-control/hot_remove
     - zram0 removal fails with EBUSY, as expected
 - unmount zram0
 - try zram0 hot remove again
   + echo 0 > /sys/class/zram-control/hot_remove
     - fails with ENODEV (unexpected)
 - unload zram kernel module
   + completes successfully
 - zram0 device node still exists
 - attempt to mount /dev/zram0
   + mount command is killed
   + following BUG is encountered

 BUG: unable to handle kernel paging request at ffffffffa0002ba0
 IP: get_disk+0x16/0x50
 Oops: 0000 [#1] SMP
 CPU: 0 PID: 252 Comm: mount Not tainted 4.9.0-rc6 #176
 Call Trace:
   exact_lock+0xc/0x20
   kobj_lookup+0xdc/0x160
   get_gendisk+0x2f/0x110
   __blkdev_get+0x10c/0x3c0
   blkdev_get+0x19d/0x2e0
   blkdev_open+0x56/0x70
   do_dentry_open.isra.19+0x1ff/0x310
   vfs_open+0x43/0x60
   path_openat+0x2c9/0xf30
   do_filp_open+0x79/0xd0
   do_sys_open+0x114/0x1e0
   SyS_open+0x19/0x20
   entry_SYSCALL_64_fastpath+0x13/0x94

This patch adds the proper error check in hot_remove_store() not to call
idr_remove() unconditionally.

Fixes: 17ec4cd98578 ("zram: don't call idr_remove() from zram_remove()")
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=1010970
Link: http://lkml.kernel.org/r/20161121132140.12683-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: David Disseldorp <ddiss@suse.de>
Reported-by: David Disseldorp <ddiss@suse.de>
Tested-by: David Disseldorp <ddiss@suse.de>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: <stable@vger.kernel.org> [4.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8 years agothp: fix corner case of munlock() of PTE-mapped THPs
Kirill A. Shutemov [Wed, 30 Nov 2016 23:54:05 +0000 (15:54 -0800)]
thp: fix corner case of munlock() of PTE-mapped THPs

The following program triggers BUG() in munlock_vma_pages_range():

// autogenerated by syzkaller (http://github.com/google/syzkaller)
#include <sys/mman.h>

int main()
{
  mmap((void*)0x20105000ul, 0xc00000ul, 0x2ul, 0x2172ul, -1, 0);
  mremap((void*)0x201fd000ul, 0x4000ul, 0xc00000ul, 0x3ul, 0x203f0000ul);
  return 0;
}

The test-case constructs the situation when munlock_vma_pages_range()
finds PTE-mapped THP-head in the middle of page table and, by mistake,
skips HPAGE_PMD_NR pages after that.

As result, on the next iteration it hits the middle of PMD-mapped THP
and gets upset seeing mlocked tail page.

The solution is only skip HPAGE_PMD_NR pages if the THP was mlocked
during munlock_vma_page().  It would guarantee that the page is
PMD-mapped as we never mlock PTE-mapeed THPs.

Fixes: e90309c9f772 ("thp: allow mlocked THP again")
Link: http://lkml.kernel.org/r/20161115132703.7s7rrgmwttegcdh4@black.fi.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: syzkaller <syzkaller@googlegroups.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org> [4.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8 years agomm, thp: propagation of conditional compilation in khugepaged.c
Jérémy Lefaure [Wed, 30 Nov 2016 23:54:02 +0000 (15:54 -0800)]
mm, thp: propagation of conditional compilation in khugepaged.c

Commit b46e756f5e47 ("thp: extract khugepaged from mm/huge_memory.c")
moved code from huge_memory.c to khugepaged.c.  Some of this code should
be compiled only when CONFIG_SYSFS is enabled but the condition around
this code was not moved into khugepaged.c.

The result is a compilation error when CONFIG_SYSFS is disabled:

  mm/built-in.o: In function `khugepaged_defrag_store': khugepaged.c:(.text+0x2d095): undefined reference to `single_hugepage_flag_store'
  mm/built-in.o: In function `khugepaged_defrag_show': khugepaged.c:(.text+0x2d0ab): undefined reference to `single_hugepage_flag_show'

This commit adds the #ifdef CONFIG_SYSFS around the code related to
sysfs.

Link: http://lkml.kernel.org/r/20161114203448.24197-1-jeremy.lefaure@lse.epita.fr
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8 years agoMerge tag 'drm-misc-fixes-2016-11-30' of git://anongit.freedesktop.org/git/drm-misc...
Dave Airlie [Thu, 1 Dec 2016 00:00:14 +0000 (10:00 +1000)]
Merge tag 'drm-misc-fixes-2016-11-30' of git://anongit.freedesktop.org/git/drm-misc into drm-fixes

single drm fix.

* tag 'drm-misc-fixes-2016-11-30' of git://anongit.freedesktop.org/git/drm-misc:
  drm: Don't call drm_for_each_crtc with a non-KMS driver

8 years agoMerge tag 'tilcdc-4.10' of https://github.com/jsarha/linux into drm-next
Dave Airlie [Wed, 30 Nov 2016 23:26:55 +0000 (09:26 +1000)]
Merge tag 'tilcdc-4.10' of https://github.com/jsarha/linux into drm-next

tilcdc changes for v4.10

* tag 'tilcdc-4.10' of https://github.com/jsarha/linux: (23 commits)
  drm/tilcdc: fix parsing of some DT properties
  drm/tilcdc: Enable frame done irq and functionality for LCDC rev 1
  drm/tilcdc: Configure video mode to HW in enable() not in mode_set_nofb()
  drm/tilcdc: Load palette at the end of mode_set_nofb()
  drm/tilcdc: Add timeout wait for palette loading to complete
  drm/tilcdc: Enable palette loading for revision 2 LCDC too
  drm/tilcdc: Fix load mode bit-field setting in tilcdc_crtc_enable()
  drm/tilcdc: Add tilcdc_write_mask() to tilcdc_regs.h
  drm/tilcdc: Fix tilcdc_crtc_create() return value handling
  drm/tilcdc: implement palette loading for rev1
  drm/tilcdc: Enable sync lost error and recovery handling for rev 1 LCDC
  drm/tilcdc: Add drm bridge support for attaching drm bridge drivers
  drm/bridge: Add ti-tfp410 DVI transmitter driver
  dt-bindings: Move "ti,tfp410.txt" from display/ti to display/bridge
  drm/tilcdc: Recover from sync lost error flood by resetting the LCDC
  drm/tilcdc: Fix race from forced shutdown of crtc in unload
  drm/tilcdc: Use unload to handle initialization failures
  drm/tilcdc: Stop using struct drm_driver load() callback
  drm/tilcdc: Remove obsolete drm_connector_register() calls
  drm/tilcdc: Correct misspelling in error message
  ...

8 years agoMerge branch 'msm-next' of git://people.freedesktop.org/~robclark/linux into drm...
Dave Airlie [Wed, 30 Nov 2016 23:25:58 +0000 (09:25 +1000)]
Merge branch 'msm-next' of git://people.freedesktop.org/~robclark/linux into drm-next

On the userspace side, all the basics are working, and most of glmark2
is working.  I've been working through deqp, and I've got a couple more
things to fix (but we've gone from 70% to 80+% pass in last day, and
current deqp run that is going should pick up another 5-10%).  I expect
to push the mesa patches today or tomorrow.

There are a couple more a5xx related patches to take the gpu out of
secure mode (for the devices that come up in secure mode, like the hw
I have), but those depend on an scm patch that would come in through
another tree.  If that can land in the next day or two, there might
be a second late pull request for drm/msm.

In addition to the new-shiny, there have also been a lot of overlay/
plane related fixes for issues found using drm-hwc2 (in the process of
testing/debugging the atomic/kms fence patches), resulting in rework
to assign hwpipes to kms planes dynamically (as part of global atomic
state) and also handling SMP (fifo) block allocation atomically as
part of the ->atomic_check() step.  All those patches should also help
out atomic weston (when those patches eventually land).

* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (36 commits)
  drm/msm: gpu: Add support for the GPMU
  drm/msm: gpu: Add A5XX target support
  drm/msm: Disable interrupts during init
  drm/msm: Remove 'src_clk' from adreno configuration
  drm/msm: gpu: Add OUT_TYPE4 and OUT_TYPE7
  drm/msm: Add adreno_gpu_write64()
  drm/msm: gpu Add new gpu register read/write functions
  drm/msm: gpu: Return error on hw_init failure
  drm/msm: gpu: Cut down the list of "generic" registers to the ones we use
  drm/msm: update generated headers
  drm/msm/adreno: move scratch register dumping to per-gen code
  drm/msm/rd: support for 64b iova
  drm/msm: convert iova to 64b
  drm/msm: set dma_mask properly
  drm/msm: Remove bad calls to of_node_put()
  drm/msm/mdp5: move LM bounds check into plane->atomic_check()
  drm/msm/mdp5: dump smp state on errors too
  drm/msm/mdp5: add debugfs to show smp block status
  drm/msm/mdp5: handle SMP block allocations "atomically"
  drm/msm/mdp5: dynamically assign hw pipes to planes
  ...

8 years agoMerge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Wed, 30 Nov 2016 23:15:49 +0000 (15:15 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux

Pull clk fixes from Stephen Boyd:
 "Two small fixes for MIPI PLLs on sunxi devices and a build fix for a
  Broadcom clk driver having unmet dependencies"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: bcm: Fix unmet Kconfig dependencies for CLK_BCM_63XX
  clk: sunxi-ng: enable so-said LDOs for A33 SoC's pll-mipi clock
  clk: sunxi-ng: sun6i-a31: Enable PLL-MIPI LDOs when ungating it

8 years agoarm64: dts: juno: Correct PCI IO window
Jeremy Linton [Tue, 29 Nov 2016 20:45:10 +0000 (14:45 -0600)]
arm64: dts: juno: Correct PCI IO window

The PCIe root complex on Juno translates the MMIO mapped
at 0x5f800000 to the PIO address range starting at 0
(which is common because PIO addresses are generally < 64k).
Correct the DT to reflect this.

Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
8 years agomacvtap: handle ubuf refcount correctly when meet errors
Jason Wang [Wed, 30 Nov 2016 05:17:52 +0000 (13:17 +0800)]
macvtap: handle ubuf refcount correctly when meet errors

We trigger uarg->callback() immediately after we decide do datacopy
even if caller want to do zerocopy. This will cause the callback
(vhost_net_zerocopy_callback) decrease the refcount. But when we meet
an error afterwards, the error handling in vhost handle_tx() will try
to decrease it again. This is wrong and fix this by delay the
uarg->callback() until we're sure there's no errors.

Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agotun: handle ubuf refcount correctly when meet errors
Jason Wang [Wed, 30 Nov 2016 05:17:51 +0000 (13:17 +0800)]
tun: handle ubuf refcount correctly when meet errors

We trigger uarg->callback() immediately after we decide do datacopy
even if caller want to do zerocopy. This will cause the callback
(vhost_net_zerocopy_callback) decrease the refcount. But when we meet
an error afterwards, the error handling in vhost handle_tx() will try
to decrease it again. This is wrong and fix this by delay the
uarg->callback() until we're sure there's no errors.

Reported-by: wangyunjian <wangyunjian@huawei.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years agonet: ethernet: ti: cpsw: fix ASSERT_RTNL() warning during resume
Grygorii Strashko [Tue, 29 Nov 2016 22:27:03 +0000 (16:27 -0600)]
net: ethernet: ti: cpsw: fix ASSERT_RTNL() warning during resume

netif_set_real_num_tx/rx_queues() are required to be called with rtnl_lock
taken, otherwise ASSERT_RTNL() warning will be triggered - which happens
now during System resume from suspend:
cpsw_resume()
|- cpsw_ndo_open()
  |- netif_set_real_num_tx/rx_queues()
     |- ASSERT_RTNL();

Hence, fix it by surrounding cpsw_ndo_open() by rtnl_lock/unlock() calls.

Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Fixes: commit e05107e6b747 ("net: ethernet: ti: cpsw: add multi queue support")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>