Bluetooth: Introduce a flags variable to Three-wire UART state

This patch introduces a flags variable to the Three-wire UART state
struct and converts the two existing bools in the struct into flags.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Improve Three-wire UART configuration handling

The configuration request/response messages contain a configuration
field which contains the sliding window size (amount of unacked reliable
packets that can be pending). This patch makes sure that we configure
the correct size (minimum of local and remote values) and use it when
determining whether to send new packets or not.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Remove unnecessary h5_build_pkt function

The implementation of h5_build_packet can be moved into
h5_prepare_pkt since all h5_prepare_pkt does is determine whether the
packet is reliable and then call h5_build_packet.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Implement proper low-power support for Three-wire UART

This patch adds on-demand wakeup request sending (and re-sendind) when
we are in low-power state. When the controller enters this state it will
send a sleep message after which the host is not allowed to send any
other packets until a wakeup request has been sent and the woken message
received as a response to it. The wakeup requests are re-sent
periodically until a woken message is received.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add initialization tracking to HCI Three-wire driver

This patch adds tracking for the uninitialized, initialized and active
states for Three-wire UART. This is needed so we can handle periodic
sending of the Link Establishment messages before reaching active state
and so that we do not try to do any higher level HCI data transmission
before reaching active state.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add initial sleep support to Three-wire UART

This patch adds very basic support for the sleep related messages. The
only thing the code does right now is send a wakeup message as soon as
receiving a sleep one, essentially preventing the controller from going
to sleep.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Improve rx debug logs for Three-wire UART

Remove unnecessary debug logs and add some to more centralized places.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Use delayed init for Three-wire UART

This patch takes into use the delayed initialization feature that the
Bluetooth UART framework provides.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add delayed init sequence support for UART controllers

This patch makes it possible to have UART drivers perform an internal
initialization before calling hci_register_dev. This allows moving a lot
of init code from user space (hciattach) to the kernel side, thereby
creating a more controlled/robust initialization process.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Simplify hci_uart_tty_close logic

This patch cleans up and reduces indentation in the hci_uart_tty_close
function.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add support for Three-wire Link Control packets

This patch adds basic support for parsing and sending Three-wire UART
Link Control packets.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix/implement Three-wire reliable packet sending

This patch should complete the necessary code for sending reliable
Three-wire packets.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add Three-wire header value convenience macros

This patch adds convenience macros for reading Three-wire header values.
This will help make the code more readable.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add initial packet sending support to Three-wire UART

This patch adds initial packed encoding and sending support to the
Three-wire UART HCI transport driver.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add basic packet parsing to Three-wire UART driver

This patch adds basic packet parsing to the Three-wire UART HCI driver
for packets received from the controller.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add initial reliable packet support for Three-wire UART

This patch adds initial support for reliable packets along with the
necessary retransmission timer for the Three-wire UART HCI driver.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add basic state tracking to Three-wire UART driver

This patch adds basic state tracking and socket buffer handling to the
Three-wire UART (H5) HCI driver.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Initial skeleton for Three-wire UART (H5) support

This patch adds the initial skeleton for Three-wire UART (H5) support
and hooks it up to the HCI UART framework.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Change page scan interval in fast connectable mode

This patch is based on a user space (hciops) patch which never made it
upstream but does make sense to include in the mgmt part of the kernel.

(User space) commit message from Dmitriy Paliy:
"
Page scan interval in fast connectable mode is changed from 22.5 msec to
160 msec to perform less aggressive page scanning. This is done
accordingly to controller vendor recommendation.

Primary concern is that current parameters 22.5 interval, 11.25 window,
and interleaved scanning occupy whole radio bandwidth. Changing interval
to 160 msec should be sufficient for both speeding up connection
establishment and leaving space for other activities, like inquiry scan,
e.g.
"

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Use tx window from config response for ack timing

This change addresses an L2CAP ERTM throughput problem when a remote
device does not fully utilize the available transmit window.

The L2CAP ERTM transmit window size determines the maximum number of
unacked frames that may be outstanding at any time. It is configured
separately for each direction of an ERTM connection. Each side sends a
configuration request with a tx_win field indicating how many unacked
frames it is capable of receiving before sending an ack. The
configuration response's tx_win field shows how many frames the
transmitter will actually send before waiting for an ack.

It's important to trace both the actual transmit window (to check for
validity of incoming frames) and the number of frames that the
transmitter will send before waiting (to send acks at the appropriate
time). Now there are separate tx_win and ack_win values. ack_win is
updated based on configuration responses, and is used to determine
when acks are sent.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: debug: Print amp_mgr refcnt

Improve debug output.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: debug: Print l2cap_chan refcount

Improve debug output.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: debug: Use standard hex object specifiers in hci_event

To help debugging printed hex object use standard bluetooth
specifiers in hci_event. The patch changes format from 0x%04x to 0x%4.4x;
print manufacturer id and handle in hex instead of int; print opcode
always in 0x%4.4x format; status in 0x%2.2x.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: debug: Add debug to l2cap_security_cfm

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: debug: Print CID and PSM in hex format

Correct places where CID and PSM were printed as int. For CID: 0x%4.4x
is used and for PSM: 0x%2.2x.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: debug: Correct types specifiers for L2CAP

Avoid unneeded type conversion by correcting type specifiers in debug
statements for L2CAP.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: debug: Add printing num of cmds queued

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Refactor PIN code rejection to use user_pairing_resp()

Reuse user_pairing_resp() to send PIN code negative reply

Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: btmrvl: trivial style fixes

Patch shortens locals scope and adds missing braces. This is a diff
between v1 which was applied and v2 of patch "Bluetooth: btmrvl: Do
not send vendor events to bluetooth stack".

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Do not auto off AMP controller

Since AMP controller is not managed by user space do not shut it down.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: bluecard_cs: Shorten scope for iobase

Shortening scope shall silence some warnings reported by Geert
Uytterhoeven:

...
drivers/bluetooth/bluecard_cs.c: warning: unused variable 'iobase'
[-Wunused-variable]
...

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Route traffic only through BR/EDR controller

If AMP controller is first in the list then Bluetooth traffic might
be routed through it (if source is not specified). The patch
prevents this case and also checks that source is BR/EDR.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix warning: using int as NULL pointer

Fix for warnings below:

...
drivers/bluetooth/bt3c_cs.c:667:20: warning: Using plain integer
as NULL pointer
drivers/bluetooth/btuart_cs.c:596:20: warning: Using plain integer
as NULL pointer
...

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: cleanup dtl1_config

Improve the error handling of dtl1_config()

Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Improve debugging messages for hci_conn

Improve debugging of hci_conn objects by: adding print to hci_conn
refcounting, adding object spcifier when missing, change conn to hcon
since conn is heavily used for l2cap_conn objects and this is misleading.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth

Bluetooth: Use GFP_KERNEL in mgmt events functions

cmd_status, cmd_complete and mgmt_event functions are executed in
process context and they are not called inside atomic sections. Thus,
they should use GFP_KERNEL for memory allocation instead of GFP_ATOMIC.

Signed-off-by: Andre Guedes <aguedespe@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Use GFP_KERNEL in mgmt_pending_add

We are allowed to sleep in mgmt_pending_add, so we should use
GFP_KERNEL for memory allocations instead of GFP_ATOMIC.

Signed-off-by: Andre Guedes <aguedespe@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Use GFP_KERNEL in mgmt_handlers

add_uuid and get_connections mgmt_handlers are executed by user
threads running in kernel-mode.

Signed-off-by: Andre Guedes <aguedespe@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: btmrvl: Do not send vendor events to bluetooth stack

Vendor-specific events shall be processed in driver and not sent
to bluetooth stack where they screw up HCI command countings.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Use AUTO_OFF constant in jiffies

Move AUTO_OFF_TIMEOUT to other constants changing name to
HCI_AUTO_OFF_TIMEOUT and convert to jiffies.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix compile warnings in mgmt

Commit af7985bf85840e3dc90ba108a679db044f91f00e introduced regression
resulting in complie warnings:

...
net/bluetooth/mgmt.c:3568:27: warning: invalid assignment: |=
net/bluetooth/mgmt.c:3568:27:    left side has type restricted __le32
net/bluetooth/mgmt.c:3568:27:    right side has type int
net/bluetooth/mgmt.c:3570:27: warning: invalid assignment: |=
net/bluetooth/mgmt.c:3570:27:    left side has type restricted __le32
net/bluetooth/mgmt.c:3570:27:    right side has type int
net/bluetooth/mgmt.c:3580:21: warning: cast from restricted __le32
...

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix sending HCI_Disconnect only when connected

HCI_Disconnect should only be sent after connection is established.
If connection is not yet established and HCI_Disconnect is called
then disconnection complete will be received with a handle which
does not exist and hence this event will be ignored.
But as mgmt.c will not receive this event, its variable for pending
command is not cleared.This will result in future Disconnect commands
for that BD Address to be blocked with error busy.

Signed-off-by: Vishal Agarwal <vishal.agarwal@stericsson.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Remove magic value in disconnect mgmt handler

This patch replaces the magic value of variable 'reason' by the
proper macro.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix flags of mgmt_device_found event

Change flags field to matches userspace structure.
This field needs to be converted to little endian before forward it.

Signed-off-by: Jefferson Delfes <jefferson.delfes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix not setting HCI_RESET flag for AMP

Move reset function to common initialization section fixing
not setting HCI_RESET flag for amp_init.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Correct debug print specifier for u16 objects

Some functions print u16 objects as "0xc03" others as "0x0c03". Patch
ensures that opcodes printed are the in the same format and consistent
with bluetooth code.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add opcode to error message

Sometimes HCI command sending timeouts and gives error message without
specifying which command causes error. Patch makes sure that opcode
is printed to help debugging.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Update HCI timeouts constants to use msecs_to_jiffies

The HCI constants are always used in form of jiffies. So just
include the conversion from msecs in the define itself. This has the
advantage of making the code where the timeout is used more readable
and avoiding unnecessary conversions.

The patch is similar to commit ba13ccd9 doing the same job for L2CAP

Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Use standard HCI cmd timeout for RESET

Remove magic and use standard HCI cmd timeout

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: add support for atheros 0930:0219

Add support for the AR3012 chip found on the Toshiba Sallite M840-1000-XQ.

usb-devices shows:

T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0930 ProdID=0219 Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: Giancarlo Formicuccia <giancarlo.formicuccia@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix using uninitialized option in RFCMode

If remote device sends bogus RFC option with invalid length,
undefined options values are used. Fix this by using defaults when
remote misbehaves.

This also fixes the following warning reported by gcc 4.7.0:

net/bluetooth/l2cap_core.c: In function 'l2cap_config_rsp':
net/bluetooth/l2cap_core.c:3302:13: warning: 'rfc.max_pdu_size' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.max_pdu_size' was declared here
net/bluetooth/l2cap_core.c:3298:25: warning: 'rfc.monitor_timeout' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.monitor_timeout' was declared here
net/bluetooth/l2cap_core.c:3297:25: warning: 'rfc.retrans_timeout' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.retrans_timeout' was declared here
net/bluetooth/l2cap_core.c:3295:2: warning: 'rfc.mode' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.mode' was declared here

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth

Conflicts:
net/bluetooth/hci_event.c

Bluetooth: Support AR3011 in Acer Iconia Tab W500

Acer used this chip connected via USB:

Bus 005 Device 005: ID 0cf3:3005 Atheros Communications, Inc. AR3011 Bluetooth
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass          224 Wireless
  bDeviceSubClass         1 Radio Frequency
  bDeviceProtocol         1 Bluetooth
  bMaxPacketSize0        64
  idVendor           0x0cf3 Atheros Communications, Inc.
  idProduct          0x3005 AR3011 Bluetooth
  bcdDevice            0.01
  iManufacturer           0
  iProduct                0
  iSerial                 0
  bNumConfigurations      1

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix style in hidp code

Follow the net rules.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add support for encryption key refresh

With LE/SMP the completion of a security level elavation from medium to
high is indicated by a HCI Encryption Key Refresh Complete event. The
necessary behavior upon receiving this event is a mix of what's done for
auth_complete and encryption_change, which is also where most of the
event handling code has been copied from.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix SMP security elevation from medium to high

If we have an unauthenticated key it is not sufficient to acheive high
security. Therefore, when deciding whether to encrypt the link or
request pairing, it is essential to in addition to checking the
existence of a key to also check whether it is authenticated or not.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix deadlock and crash when SMP pairing times out

The l2cap_conn_del function tries to cancel_sync the security timer, but
when it's called from the timeout function itself a deadlock occurs.
Subsequently the "hcon->l2cap_data = NULL" that's supposed to protect
multiple calls to l2cap_conn_del never gets cleared and when the
connection finally drops we double free's etc which will crash the
kernel.

This patch fixes the issue by using the HCI_CONN_LE_SMP_PEND for
protecting against this. The same flag is also used for the same purpose
in other places in the SMP code.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix LE pairing completion on connection failure

For BR/EDR pairing is assumed to be finished when connection is
done. For LE if connection is successful it did not necessarily
mean that pairing is also done but if the connection is unsuccessful
it should be assumed that pairing procedure is also finished.
This patch registers a new function with connect_cfm_cb callback for
LE link which sends the pairing complete signal to user space if
connection is unsuccessful.

Signed-off-by: Vishal Agarwal <vishal.agarwal@stericsson.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix SMP pairing method selection

The tk_request function takes the local IO capability as the second last
parameter and the remote IO capability as the last parameter. They were
previously swapped: when we receive a pairing response
req->io_capability contains the local one and rsp->io_capability the
remote one.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Remove magic disconnect reason

The macro gives a better idea of the what the error really is.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix checking the wrong flag when accepting a socket

Most probably a typo, the check should have been for BT_SK_DEFER_SETUP
instead of BT_DEFER_SETUP (which right now only represents a socket
option).

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Filter duplicated reports in LE scan

This patch enables filtering duplicated advertising reports during
LE scan.

Some LE devices advertise using very small intervals generating lots
of equal advertising report events to the host. Each event generates
a mgmt_device_found event which is copied to userspace.

Enabling this feature, duplicated advertising reports are filtered
at controller's link layer. This way, the controller doesn't wake up
the host to report duplicated advertising reports and, consequently,
less data is copied to userspace.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Create empty l2cap ops function

A2MP doesn't use part of the L2CAP chan ops API so we just create general
empty function instead of the A2MP specific one.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Rename L2CAP_LE_DEFAULT_MTU

This patch renames L2CAP_LE_DEFAULT_MTU macro to L2CAP_LE_MIN_MTU
since it represents the minimum MTU value, not the default MTU
value for LE.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Check MTU value in l2cap_sock_setsockopt_old

If user tries to set an invalid MTU value, l2cap_sock_setsockopt_old
should return -EINVAL.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Change default MTU for L2CAP ATT channel

This patch changes the default MTU value for L2CAP ATT fixed channel
to L2CAP_DEFAULT_MTU (672 octets).

Differently from others L2CAP channels, in L2CAP ATT fixed channel
there is no MTU negotiation. The MTU value for that channel is up to
the L2CAP implementation. The only restriction in L2CAP spec is the
MTU value must not be less than 23 octets.

At ATT protocol level (on top of L2CAP), we have the ATT_MTU which
defines the maximum size of any ATT message sent between client and
server. GATT profile defines ATT_MTU default value to 23 octets. If
a GATT based profile wants to use ATT_MTU greater than 23 octets
(e.g. HID over GATT profile), it should negotiate a new value by
executing the GATT Exchange MTU sub-procedure.

Thus, in order to support any value of ATT_MTU negotiated at ATT
protocol level, our L2CAP implementation should have L2CAP ATT
fixed channel MTU equal or greater than ATT_MAX_MTU (512 octets).

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix not removing hci_conn for failed LE connection

This patch changes way LE Connection Complete event with error status are
handled. BDADDR returned in such event packet do not need to be valid and
should not be used to search for existing hci_conn. Instead, any hci_conn
with BT_CONNECT state should be matched since there can be only one
pending LE outgoing connection at any time.

If not handled properly, appriopriate hci_conn will not be removed and
subsequent connection to given peer will try to reuse it without making
actual connection attempt.

2012-05-07 11:21:39.133378 < HCI Command: LE Create Connection (0x08|0x000d) plen 25
    bdaddr 00:22:D0:10:13:EE type 1
2012-05-07 11:21:39.138774 > HCI Event: Command Status (0x0f) plen 4
    LE Create Connection (0x08|0x000d) status 0x00 ncmd 1
2012-05-07 11:21:44.752854 < HCI Command: LE Create Connection Cancel (0x08|0x000e) plen 0
2012-05-07 11:21:44.759475 > HCI Event: Command Complete (0x0e) plen 4
    LE Create Connection Cancel (0x08|0x000e) ncmd 1
2012-05-07 11:21:44.764479 > HCI Event: LE Meta Event (0x3e) plen 19
    LE Connection Complete
      status 0x02 handle 0, role master
      bdaddr 00:00:00:00:00:00 (Public)

[14898.739425] [6603] hci_connect: hci0 dst 00:22:D0:10:13:EE
[14898.739429] [6603] hci_conn_add: hci0 dst 00:22:D0:10:13:EE
[14898.739434] [6603] hci_conn_init_sysfs: conn ffff880079f03000
[14898.739440] [6603] hci_send_cmd: hci0 opcode 0x200d plen 25
[14898.739443] [6603] hci_send_cmd: skb len 28
[14898.739487] [6603] hci_chan_create: hci0 conn ffff880079f03000
...
[14938.860231] [55] hci_send_cmd: hci0 opcode 0x200e plen 0
...
[14938.876427] [55] hci_le_conn_complete_evt: hci0 status 2
[14938.876433] [55] hci_conn_add: hci0 dst 00:00:00:00:00:00
[14938.876439] [55] hci_conn_init_sysfs: conn ffff88007aeff800
[14938.876454] [55] hci_send_to_control: len 14
[14938.876470] [55] l2cap_connect_cfm: hcon ffff88007aeff800 bdaddr 00:00:00:00:00:00 status 2
[14938.876474] [55] hci_conn_del: hci0 conn ffff88007aeff800 handle 0

Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Acked-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Return proper mgmt state when LE pairing connection failed

MGMT_STATUS_BUSY should be returned when LE pairing cannot be started due
to another outgoing connection attempt is ongoing.

Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Allow only one LE connection attempt

Only one outgoing LE connection attempt should be possible.
hci_connect() will now return -EBUSY in case there's another pending
outgoing connection.

Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Remove unused err var from l2cap_segment_sdu()

Trivial fix, let the code cleaner.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Create function to return the ERTM header size

Simplify the handling of different ERTM header size. We were the same
check in some places of the code, and more is expected to come, so just
replace them with a function.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Make l2cap_att_channel return void

l2cap_att_channel always returns 0 which is not used.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Make l2cap_conless_channel return void

l2cap_conless_channel always return 0 which is not used.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Make l2cap_data_channel return void

l2cap_data_channel always return 0 which is not used anywhere,
make it void function.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Do not reference hci_conn

Make A2MP channel special channel which do not reference hci_conn.
This prevents from keeping ACL connection open when all L2CAP
channels got closed.

hci_conn_hold and hci_conn_put are not reference counts on the
hci_conn structure in the typical way.  They are reference counts for
the ACL.  When you do the last hci_conn_put, the ACL is disconnected
after a timeout.

Reported-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Do not check func ready existence

Functions will be always defined and in case not implemented as
dummy __no_func.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Remove unused HCI timeouts definitions

Those are not used anywhere in code (and never were since introduction
in 2006) so just remove them.

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Manage incoming connections

Handle incoming A2MP connection by creating AMP manager and
processing A2MP messages.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Handling fixed channels

A2MP fixed channel do not have sk

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Process A2MP Command Responses

Process A2MP responses, print cmd code and ident for now.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Process A2MP Disc Physlink Request

Placeholder for A2MP Disconnect Physlink Request.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Process A2MP Create Physlink Request

Placeholder for A2MP Create Physlink Request.
Handles requests with invalid controler id as shown below:

...
> ACL data: handle 11 flags 0x02 dlen 50
    A2MP: Create Physical Link req: local id 1 remote id 85
      Assoc data:
        <skipped>
< ACL data: handle 11 flags 0x00 dlen 15
    A2MP: Create Physical Link rsp: local id 85 remote id 1 status 1
      Invalid Controller ID
...

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Process A2MP Get AMP Assoc Request

Example trace when receiving AMP Assoc Request with wrong AMP id.
...
> ACL data: handle 11 flags 0x02 dlen 13
    A2MP: Get AMP Assoc req: id 238
< ACL data: handle 11 flags 0x00 dlen 14
    A2MP: Get AMP Assoc rsp: id 238 status (1) Invalid Controller ID
      assoc data:
...

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Process A2MP Get Info Request

Process A2MP Get Info Request.
Example of trace log for invalid controller id is shown below:

...
> ACL data: handle 11 flags 0x02 dlen 13
    A2MP: Get Info req: id 238
< ACL data: handle 11 flags 0x00 dlen 30
    A2MP: Get Info rsp: id 238 status (1) Invalid Controller ID
...

Note that If the Status field is set to Invalid Controller ID all subsequent
fields in the AMP Get Info Response shall be ignored by the receiver.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Process A2MP Change Notify

Placeholder for A2MP Change Notify handler.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Process A2MP Discover Request

Adds helper functions to count HCI devs and process A2MP Discover
Request, code makes sure that first controller in the list is
BREDR one. Trace is shown below:

...
> ACL data: handle 11 flags 0x02 dlen 16
    A2MP: Discover req: mtu/mps 670 mask: 0x0000
< ACL data: handle 11 flags 0x00 dlen 22
    A2MP: Discover rsp: mtu/mps 670 mask: 0x0000
      Controller list:
        id 0 type 0 (BR-EDR) status 0x01 (Bluetooth only)
        id 1 type 1 (802.11 AMP) status 0x01 (Bluetooth only)
...

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Process A2MP Command Reject

Placeholder for future A2MP Command Reject handler.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Process A2MP messages

Implement basic processing for AMP Manager Protocol (A2MP).

Example below shows processing unrecognized command.
...
> ACL data: handle 11 flags 0x02 dlen 12
    A2MP: code 0x00 ident 3 len 0
< ACL data: handle 11 flags 0x00 dlen 14
    A2MP: Command Reject: reason (0) - Command not recognized
...

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Define A2MP status codes

A2MP status codes copied from Bluez patch sent by Peter Krystad
<pkrystad@codeaurora.org>.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Definitions for A2MP commands

Define A2MP command IDs and packet structures.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Add chan callbacks

Add L2CAP chan ops callbacks.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Build and Send msg helpers

Helper function to build and send A2MP messages.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: AMP Manager basic functions

Define AMP Manager and some basic functions.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: A2MP: Create A2MP channel

Create and initialize fixed A2MP channel

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: trivial: Use defined PSMLEN instead of magic

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: check for already existent channel before create new one

Move this check to before the channel time creation simplifies the code
and avoid memory allocation if the channel already exist.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Move check for backlog size to l2cap_sock.c

Remove socket specific code from l2cap_core.c

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use chan->state instead of sk->sk_state

These vars are kept in sync so we can use chan->state here.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add l2cap_chan->ops->ready()

This move socket specific code to l2cap_sock.c.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>