Felix Fietkau [Mon, 27 Nov 2023 17:37:55 +0000 (18:37 +0100)]
udebug: update to Git HEAD (2023-11-27)
a2301fa3b0c6 README: add wireshark info
cfd83ccc1e4e server: properly handle unclaimed file descriptors
cb71f64de0ec lib: remove leftover debug code
a92101631c0d lib: fix avl tree lookup
d4b99820afd0 lib: move library code to libubox, add ubus config handling code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 27 Nov 2023 17:37:33 +0000 (18:37 +0100)]
libubox: update to Git HEAD (2023-11-27)
82fa6480de7a uloop: add support for interval timers
13d9b04fb09d uloop: add support for user defined signal handlers
f7d156911311 uloop: properly initialize signal handler mask
8a5a4319a85c uloop: fix typo in signal handling rework
b3fa3d92e3eb uloop: reset flags after __uloop_fd_delete call
d4c3066e7c5e udebug: add udebug library code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
David Bauer [Mon, 20 Nov 2023 15:36:43 +0000 (16:36 +0100)]
mediatek: copy config for Acer Predator W6
Config was previously not copied on sysupgrade.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Thu, 20 Apr 2023 17:49:55 +0000 (19:49 +0200)]
mediatek: add support for GL.iNet GL-MT2500
Hardware
--------
SoC: MediaTek MT7981BA
RAM: 1GB DDR4 (NANYA NT5AD512M16C4-JR)
MMC: 8GB eMMC (Samsung 8GTF4R)
ETH: 1000Base-T LAN (ePHY)
2500Base-T WAN (MaxLinear GPY211C)
BTN: 1x Reset Button
LED: System (blue/white)
VPN (white)
USB: 1x USB-A (USB 3.0)
UART: 115200 8N1 - Pinout on board next to LAN port
Don't connect 3.3V!
Known Issues
------------
U-Boot vendor recovery does not seem to accept any images, neither
GL.iNet images nor OpenWrt images. Recovery requires serial access!
Installation
------------
Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to
not retain existing settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Tue, 21 Nov 2023 13:10:09 +0000 (14:10 +0100)]
rockchip: require image metadata
All devices in the rockchip target have appended image-metadata. Enforce
the presence of this metadata to avoid flashing incomplete images.
This is the de-facto standard for almost all OpenWrt targets.
Signed-off-by: David Bauer <mail@david-bauer.net>
Lech Perczak [Thu, 16 Nov 2023 16:30:11 +0000 (17:30 +0100)]
ath79: fortinet-fap-221-b: convert to nvmem-layout
Now that MAC address parser supports the hex format (without
delimiters), use the canonical MAC address stored in U-boot partition.
Get rid of the userspace adjustments which are no longer necessary.
While at that, move the mac-base to the common part, as it is again
exactly the same in both models.
And convert ART partition too - keep that one separate, as calibration
data length differs between the models.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Lech Perczak [Thu, 16 Nov 2023 16:17:32 +0000 (17:17 +0100)]
ath79: fortinet-fap-220-b: convert to nvmem-layout
Now that MAC address parser supports the hex format (without
delimiters), use the canonical MAC address stored in U-boot partition.
Get rid of the "mac-address-increment" binding.
While at that, convert ART partition too.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Lech Perczak [Sat, 25 Nov 2023 02:09:30 +0000 (03:09 +0100)]
ath79: fortinet-fap-220-b: fix WLAN MAC addresses
Addresses were swapped compared to the factory firmware. In addition to
that, one of them was shifted by -1. Fix that by setting wlan0 MAC
offset to 9, and wlan1 MAC offset to 2.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Hauke Mehrtens [Sun, 26 Nov 2023 19:37:01 +0000 (20:37 +0100)]
ustream-ssl: update to Git HEAD (2023-11-26)
91666a3 ustream-mbedtls: Add compatibility with Mbed TLS 3.0.0
263b9a9 cmake: Fail if undefined symbols are used
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Xiaojun Liu [Mon, 13 Nov 2023 03:59:45 +0000 (03:59 +0000)]
x86 64: Add new device Cordoba Edge Platform
Add new device Cordoba Edge Platform
hardware specifications: CPU - Intel Atom C3000
Ethernet - 2 10Gbps ixgbe SPF+
2 1Gbps ixgbe RJ45/SPF
4 2.5Gbps igc RJ45
WiFi - mt7915e
LED - 3 multicolor(red|blue|green) LEDs
Signed-off-by: Xiaojun Liu <xiaojun.liu@silicom.co.il>
Sven Eckelmann [Sat, 18 Nov 2023 15:29:09 +0000 (16:29 +0100)]
dnsmasq: mark global ubus context as closed after fork
If the dnsmasq process forks to handle TCP connections, it closes the ubus
context. But instead of changing the daemon wide pointer to NULL, only the
local variable was adjusted - and this portion of the code was even dropped
(dead store) by some optimizing compilers.
It makes more sense to change the daemon->ubus pointer because various
functions are already checking it for NULL. It is also the behavior which
ubus_destroy() implements.
Fixes: d8b33dad0bb7 ("dnsmasq: add support for monitoring and modifying dns lookup results via ubus")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Tianling Shen [Sun, 25 Jun 2023 16:37:31 +0000 (00:37 +0800)]
rockchip: add NanoPi R5C support
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
1GB or 4GB LPDDR4X RAM
2x 2500 Base-T
4 LEDs (LAN / WAN / WIFI / POWER)
1 Button (Reset)
8GB or 32GB eMMC on-board
Micro-SD Slot
M.2 Slot
2x USB 3.0 Port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Sun, 25 Jun 2023 16:37:30 +0000 (00:37 +0800)]
uboot-rockchip: add NanoPi R5C support
Add support for the FriendlyARM NanoPi R5C.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Sun, 25 Jun 2023 16:37:30 +0000 (00:37 +0800)]
rockchip: add NanoPi R5S support
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
2GB or 4GB LPDDR4X RAM
1x 1000 Base-T
2x 2500 Base-T
4 LEDs (LAN1 / LAN2 / WAN / POWER)
8GB eMMC on-board
Micro-SD Slot
M.2 Slot
2x USB 3.0 Port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Tested-by: Packet Please <pktpls@systemli.org>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Sun, 25 Jun 2023 16:37:30 +0000 (00:37 +0800)]
uboot-rockchip: add NanoPi R5S support
Add support for the FriendlyARM NanoPi R5S support.
Tested-by: Packet Please <pktpls@systemli.org>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Sun, 25 Jun 2023 16:37:29 +0000 (00:37 +0800)]
rockchip: armv8: broaden boardname
Now we have rk356x support :-)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Sun, 25 Jun 2023 16:37:29 +0000 (00:37 +0800)]
rockchip: enable drivers for rk356x
Enable all necessary drivers for the rk356x SoCs, including PHY,
SCMI, SPI etc. Also backport 2 upstream patches for sdhci fixes.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Sun, 25 Jun 2023 16:37:29 +0000 (00:37 +0800)]
rockchip: remove kernel 5.15 patches and config
As we switched to kernel 6.1, these files can go.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Sun, 25 Jun 2023 16:37:28 +0000 (00:37 +0800)]
rockchip: switch to kernel 6.1
Required by the following rk3568 support.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Sun, 25 Jun 2023 16:37:28 +0000 (00:37 +0800)]
rockchip: move image generation command to default
It's applicable for all devices so move it to default to reduce
redudant code. Addtionally introduce a new variable `BOOT_SCRIPT`
to allow custom boot script (if necessary).
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Sun, 25 Jun 2023 16:37:28 +0000 (00:37 +0800)]
rkbin: add new TF-A package for rk35xx
Currently there's no usable mainline (open source) TF-A implementation
for rk35xx SoCs, so pack the prebuilt firmware from the vendor.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Sun, 25 Jun 2023 16:37:27 +0000 (00:37 +0800)]
uboot-rockchip: Update to 2023.07.02
* Removed swig hacks and prebuilt of-platdata
* Removed upstreamed patches
- 101-rock64pro-disable-CONFIG_USE_PREBOOT.patch
- 102-rockchip-rk3328-Add-support-for-FriendlyARM-NanoPi-R2C.patch
* Reordered patches
* Introduced new dependencies check
* Overrided default PATH to avoid race condition
(host python3 vs hostpkg python3)
* Switched to use UBOOT_CUSTOMIZE_CONFIG for config update
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Sat, 25 Nov 2023 15:17:15 +0000 (23:17 +0800)]
uboot-sunxi: use intree dtc explicitly
This replaces pylibfdt hack.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Sat, 25 Nov 2023 15:22:59 +0000 (23:22 +0800)]
uboot-sifiveu: use intree dtc explicitly
This replaces pylibfdt hack.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Sat, 25 Nov 2023 15:21:22 +0000 (23:21 +0800)]
uboot-mediatek: use intree dtc explicitly
This replaces pylibfdt hack.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Sun, 25 Jun 2023 16:37:27 +0000 (00:37 +0800)]
u-boot: introduce dependencies check for swig and pyelftools
They are required by modern u-boot builds,
e.g. uboot-rockchip and uboot-sunxi.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tony Ambardar [Sat, 11 Nov 2023 12:53:26 +0000 (04:53 -0800)]
ipq40xx: enable UBI size checks for some Linksys NAND devices
Add correct NAND_SIZE in device definitions for EA6350v3, EA8300, MR8300,
WHW01 and WHW03v2, to enable improved image size checks wrt UBI reserved
blocks on NAND devices.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Tony Ambardar [Sat, 11 Nov 2023 12:46:14 +0000 (04:46 -0800)]
image: improve UBI image sizing on NAND devices
Many NAND devices use a build recipe with "append-ubi | check-size" to
ensure factory images don't exceed the target flash partition size.
However, UBI reserves space for bad block handling and other operational
overhead, and thus 'check-size' can overestimate the space available by
several MB. In practice, this means a failed check is definitely a failure,
while a passing check is only probably a pass.
Improve the situation by teaching 'Build/append-ubi' to check image sizes
while accounting for UBI reserved blocks. Add new device variable NAND_SIZE
and use with existing IMAGE_SIZE to derate the available space. Each UBI
device reserves 20 PEBs per 1024 PEBs of the entire NAND device for bad
blocks, plus an additional 4 PEBs overhead.
Many devices can transparently enable this check by setting NAND_SIZE based
on their flash storage, and may then remove any unneeded 'check-size'.
Link: http://www.linux-mtd.infradead.org/doc/ubi.html#L_overhead
Suggested-by: Shiji Yang <yangshiji66@qq.com>
Suggested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Tony Ambardar [Tue, 14 Nov 2023 01:14:07 +0000 (17:14 -0800)]
image: fix Linksys image alignment and simplify footer creation
Current factory image sizes for Linksys devices are 256-byte aligned. This
is not an issue writing factory images from the OpenWrt or Linksys GUIs,
but can lead to failures using a TFTP client from the Linksys bootloader:
NAND write: device 1 offset 0x2800000, size 0xc00100
Attempt to write to non page aligned data
NAND write to offset
2800000 failed -22
0 bytes written: ERROR
Simplify Linksys footer creation by migrating to a makefile build recipe,
and pre-pad the footer (with 0xFF) to ensure the final image is $(PAGESIZE)
aligned. Finally, remove the old linksys-image.sh script no longer needed.
Linksys footer details are given below for future reference. The 256-byte
footer is appended to factory images and tested by both the Linksys
Upgrader (observed in EA6350v3) and OpenWrt sysupgrade.
Footer format:
.LINKSYS. Checked by Linksys upgrader before continuing. (9 bytes)
<VERSION> Upgrade version number, unchecked so arbitrary. (8 bytes)
<TYPE> Model of device, space padded (0x20). (15 bytes)
<CRC> CRC checksum of factory image to flash. (8 bytes)
<padding> Padding ('0' + 0x20 * 7) (8 bytes)
<signature> Signature of signer, unchecked so arbitrary. (16 bytes)
<padding> Padding with nulls (0x00) (192 bytes)
Link: https://github.com/openwrt/openwrt/pull/11405#issuecomment-1358510123
Link: https://github.com/openwrt/openwrt/pull/11405#issuecomment-1587517739
Reported-by: Stijn Segers <foss@volatilesystems.org>
Reported-by: Wyatt Martin <wawowl@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Tony Ambardar [Sat, 11 Nov 2023 12:29:26 +0000 (04:29 -0800)]
image: use helper function for size units
Add the make function 'exp_units' for helping evaluate k/m/g size units in
expressions, and use this to consistently replace many ad hoc substitutions
like '$(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE)))' in makefiles.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Tony Ambardar [Mon, 2 Oct 2023 04:51:32 +0000 (21:51 -0700)]
ipq40xx: fix typo in Linksys WHW01 image definition
Use lower-case "k" in IMAGE_SIZE for Linksys WHW01, permitting proper unit
conversions in build recipes (e.g. 75776k -> 75776*1024).
Fixes: 2a9f3b7717 ("ipq40xx: fix up Linksys WHW01 board name, device definition")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Rani Hod [Sun, 12 Nov 2023 23:15:31 +0000 (01:15 +0200)]
ath79: add support for D-link DAP-1720 A1
D-Link DAP-1720 rev A1 is a mains-powered AC1750 Wi-Fi range extender,
manufactured by Alpha Networks [8WAPAC28.1A1G].
(in square brackets: PCB silkscreen markings)
Specifications:
* CPU (Qualcomm Atheros QCA9563-AL3A [U5]):
775 MHz single core MIPS 74Kc;
* RAM (Winbond W9751G6KB-25J [U3]):
64 MiB DDR2;
* ROM (Winbond W25Q128FV [U16]):
16 MiB SPI NOR flash;
* Ethernet (AR8033-AL1A PHY [U1], no switch):
1 GbE RJ45 port (no PHY LEDs);
* Wi-Fi
* 2.4 GHz (Qualcomm Atheros QCA9563-AL3A [U5]):
3x3 802.11n;
* 5 GHz (Qualcomm Atheros QCA9880-BR4A [U9]):
3x3 802.11ac Wave 1;
* 3 foldable dual-band antennas (U.fl) [P1],[P2],[P3];
* GPIO LEDs:
* RSSI low (red/green) [D2];
* RSSI medium (green) [D3];
* RSSI high (green) [D4];
* status (red/green) [D5];
* GPIO buttons:
* WPS [SW1], co-located with status LED;
* reset [SW4], accessible via hole in the side;
* Serial/UART:
Tx-Gnd-3v3-Rx [JP1], Tx is the square pin, 1.25mm pitch;
125000-8-n-1 in U-boot, 115200-8-n-1 in kernel;
* Misc:
* 12V VCC [JP2], fed from internal 12V/1A AC to DC converter;
* on/off slide switch [SW2] (disconnects VCC mechanically);
* unpopulated footprints for a Wi-Fi LED [D1];
* unpopulated footprints for a 4-pin 3-position slide switch (SW3);
MAC addresses:
* Label = LAN;
* 2.4 GHz WiFi = LAN;
* 5 GHz WiFi = LAN+2;
Installation:
* `factory.bin` can be used to install OpenWrt from OEM firmware via the
standard upgrade webpage at http://192.168.0.50/UpdateFirmware.html
* `recovery.bin` can be used to install OpenWrt (or revert to OEM
firmware) from D-Link Web Recovery. To enter web recovery, keep reset
button pressed and then power on the device. Reset button can be
released when the red status LED is bright; it will then blink slowly.
Set static IP to 192.168.0.10, navigate to http://192.168.0.50 and
upload 'recovery.bin'. Note that in web recovery mode the device
ignores ping and DHCP requests.
Note: 802.11s is not supported by the default `ath10k` driver and
firmware, but is supported by the non-CT driver and firmware variants.
The `-smallbuffers` driver variant is recommended due to RAM size.
Co-developed-by: Anthony Sepa <protectivedad@gmail.com>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Rosen Penev [Sun, 26 Nov 2023 04:36:49 +0000 (20:36 -0800)]
ath79: ar: convert to mac-base
Replacement for deprecated mac-address-increment
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sun, 26 Nov 2023 03:31:17 +0000 (19:31 -0800)]
ath79: ar: convert to nvmem-layout
Will allow removing deprecated mac-address-increment.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sun, 26 Nov 2023 01:36:49 +0000 (17:36 -0800)]
ath79: tp9343: convert to nvmem-layout
Allows getting rid of deprecated mac-address-increment.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sun, 26 Nov 2023 01:25:18 +0000 (17:25 -0800)]
ath79: qcn: convert to nvmem-layout
Allows getting rid of deprecated mac-address-increment.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Fri, 10 Nov 2023 22:55:43 +0000 (14:55 -0800)]
ath79: qca: remove mac-address-increment
nvmem-layout allows removal
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Thu, 9 Nov 2023 23:18:44 +0000 (15:18 -0800)]
ath79: qca: convert to nvmem-layout
Allows replacing mac-address-increment with mac-base.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sat, 11 Nov 2023 00:21:29 +0000 (16:21 -0800)]
ath79: mikrotik: fix dts warnings
property has invalid length
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Wed, 8 Nov 2023 03:39:00 +0000 (19:39 -0800)]
ramips: mt7621: nix mac-address-increment
nvmem-layout allows removal
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Tue, 7 Nov 2023 23:55:58 +0000 (15:55 -0800)]
ramips: mt7621: convert to nvmem-layout
Allows replacing mac-address-increment with mac-base.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Wed, 8 Nov 2023 03:25:58 +0000 (19:25 -0800)]
ramips: mt7621: add interrupt-controller
Fixes dtc warning:
'#interrupt-cells' found, but node is not an interrupt provider
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sat, 25 Nov 2023 21:35:04 +0000 (13:35 -0800)]
ramips: mt7620a: use mac-base
mac-address-increment is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sat, 25 Nov 2023 21:20:44 +0000 (13:20 -0800)]
ramips: mt7620a: convert to nvmem-layout
Allows using mac-base to replace mac-address-increment.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sat, 25 Nov 2023 20:32:55 +0000 (12:32 -0800)]
ramips: mt7620n: convert to nvmem-layout
nvmem-cells is deprecated. nvmem-layout allows using mac-base.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Fri, 24 Nov 2023 02:59:35 +0000 (18:59 -0800)]
ramips: mt7628: use mac-base
mac-address-increment is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Fri, 24 Nov 2023 02:31:55 +0000 (18:31 -0800)]
ramips: mt7628: use nvmem-layout
Will allow using mac-base.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sat, 25 Nov 2023 22:11:08 +0000 (14:11 -0800)]
mediatek: use mac-base
mac-address-increment is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sat, 25 Nov 2023 22:03:10 +0000 (14:03 -0800)]
mediatek: convert to nvmem-layout
Will allow removing mac-address-increment.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Fri, 24 Nov 2023 01:40:09 +0000 (17:40 -0800)]
ramips: rtxxxx: remove mac-address-increment
Deprecated and replaced upstream with mac-base.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Wed, 22 Nov 2023 23:48:24 +0000 (15:48 -0800)]
ramips: rtxxxx: convert to nvmem-layout
Allows replacing mac-adress-increment.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Chukun Pan [Mon, 6 Nov 2023 15:06:05 +0000 (23:06 +0800)]
mediatek: filogic: reorder alphabetically
Reorder scripts and image recipes to keep alphabetical order.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Chukun Pan [Sun, 5 Nov 2023 15:02:09 +0000 (23:02 +0800)]
uboot-envtools: filogic: reorder alphabetically
Reorder scripts to keep alphabetical order.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Chukun Pan [Fri, 17 Nov 2023 15:27:03 +0000 (23:27 +0800)]
mediatek: filogic: remove kmod-usb2 for GL-MT6000
The usb driver requires kmod-usb3, not kmod-usb2.
Remove the useless kmod-usb2 from default package.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Chukun Pan [Sat, 4 Nov 2023 15:50:20 +0000 (23:50 +0800)]
mediatek: Cetron CT3003: fixes typo for spi properties
Same as commit
3674689, correct 'buswidth' to 'bus-width'.
Also move the nmbm properties outside the partition definition.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Rosen Penev [Mon, 13 Nov 2023 19:47:17 +0000 (11:47 -0800)]
ipq40xx: remove mac-address-increment
nvmem-layout allows removal
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Mon, 13 Nov 2023 19:23:12 +0000 (11:23 -0800)]
ipq40xx: convert to nvmem-layout
Allows replacing mac-address-increment with mac-base.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Mon, 13 Nov 2023 20:02:38 +0000 (12:02 -0800)]
ipq40xx: fix dtc warnimg
I2C bus unit address format error, expected "62"
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Mon, 13 Nov 2023 20:20:51 +0000 (12:20 -0800)]
qualcommax: convert to nvmem-layout
nvmem-cells is deprecated
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Mon, 13 Nov 2023 20:23:07 +0000 (12:23 -0800)]
apm821xx: convert to nvmem-layout
nvmem-cells is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Hauke Mehrtens [Sat, 25 Nov 2023 17:06:41 +0000 (18:06 +0100)]
mediatek: filogic: Fix GPIOs for Zbtlink ZBT-Z8102AX
The PGIO configuration should be added for the ZBT-Z8102AX and not the ZBT-Z8103AX
Fixes: c8c2f522625c ("mediatek: add support for Zbtlink ZBT-Z8102AX")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Xiaobo Liu [Tue, 14 Nov 2023 03:07:56 +0000 (11:07 +0800)]
ramips: mt76x8 add support for RTC class/drivers
This commit adds support for RTC class/drivers to the mt76x8 target.
Signed-off-by: Xiaobo Liu <cppcoffee@gmail.com>
Rosen Penev [Sat, 7 Oct 2023 04:55:01 +0000 (21:55 -0700)]
f2fs-tools: avoid dead symlinks in root
When building on the host, this avoids creating dead symlinks. Matches
what is done elsewhere.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Darlan Pedro de Campos [Fri, 24 Nov 2023 00:31:05 +0000 (19:31 -0500)]
ramips: add support for TP-Link EX220 v1
This device is very similar, if not identical, to the TP-Link AX23 v1
but is targeted at service providers and features a completely different
flash layout.
Hardware
--------
CPU: MediaTek MT7621 DAT
RAM: 128MB DDR3 (integrated)
FLASH: 16MB SPI-NOR
WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
LEDs - (3V3 - GND - RX - TX) - ETH ports
Installation
------------
Flashing is only possible via a serial connection using the sysupgrade
image; the factory image must be signed. You can flash the sysupgrade
image directly through the U-Boot console, or preferably, by booting the
initramfs image and flashing with the sysupgrade command. Follow these
steps for sysupgrade flashing:
1. Establish a UART serial connection.
2. Set up a TFTP server at 192.168.0.2 and copy the initramfs image
there.
3. Power on the device and press any key to interrupt normal boot.
4. Load the initramfs image using tftpboot.
5. Boot with bootm.
6. If you haven't done so already, back up all stock mtd partitions.
7. Copy the sysupgrade image to the router.
8. Flash OpenWrt through either LuCI or the sysupgrade command. Remember
not to attempt saving settings.
Revert to stock firmware
------------------------
Flash stock firmware via OEM web-recovery mode. If you don't have access
to the stock firmware image, you will need to restore the firmware
partition backed up earlier.
Web-Recovery
------------
The router supports an HTTP recovery mode:
1. Turn off the router.
2. Press the reset button and power on the device.
3. When all LEDs start flashing, release reset and quickly press it
again.
The interface is reachable at 192.168.0.1 and supports installation of
the OEM factory image. Note that flashing OpenWrt this way is not
possible, as mentioned above.
Signed-off-by: Darlan Pedro de Campos <darlanpedro@gmail.com>
Michael Trinidad [Wed, 22 Nov 2023 02:46:27 +0000 (21:46 -0500)]
mwlwifi: update to version 10.4.10-
20231120
Upstream PR 416 improvements:
-AMPDU Optimization of priority calculation. (8864/8897)
-8864/8897 fix wpa3
-Add cypher suite to driver capabilities (all chip)
-Alignment of pcie_tx_ctrl* (all chip)
-"feature" normalization for all chips (all chip)
-Add modprobe parameters (all chip)
-fix monitoring (all chip)
-Code separation by chipset (8864/8897 <=> 8997)
-dump_prob decommissioning (8864/8897/8997)
-fix amsdu high ping latency (8864/8897/8997)
-drop debug info in hostcmd_get_hw_spec() (8864/8897)
-Add wcb_base in debug info (8864)
-Rewrite AMSDU packets (8864/8897/8997)
-debug rewrite output mwl_debugfs_sta_read (all chip)
-Improved encryption interoperability (8864/8897/8997)
-factorization encrypted packet test (8864/8897/8997)
-Change 88W8864 firmware to 7.2.9.27 (8864/8897)
-Fix the AMPDU session lifecycle (8864/8897/8997)
-Remove the tx done packets mechanism (8864/8897)
Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
Filip Milivojevic [Sat, 11 Nov 2023 09:57:32 +0000 (10:57 +0100)]
ramips: Add support for Cudy WR1300 v3
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7603E, MediaTek MT7613BE
- Switch: 1 WAN, 4 LAN (Gigabit)
- Buttons: Reset, WPS
- LEDs: System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS
- Power: DC 12V 1A tip positive
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Cudy WR1300 v3 differs from v2 only in swapped WiFi chip PCIe slots. Common
nodes are extracted to .dtsi and new v2 and v3 dts are created.
Cudy WR1300 v2 dts now contains ieee80211-freq-limit and has
eeprom_factory_8000 length fixed.
The same manufacturer's built OpenWRT image is provided for both v2 and v3
devices as a step in installing, but for proper WiFi functionality,
a separate build is required.
Recovery:
- Loads only signed manufacture firmware due to bootloader RSA verification
- serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
- connect to any lan ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button for image to
download
- See http://www.cudytech.com/newsinfo/547425.html
Signed-off-by: Filip Milivojevic <zekica@gmail.com>
Nicolò Veronese [Thu, 2 Nov 2023 18:53:08 +0000 (19:53 +0100)]
uboot-envtools: add support for Zyxel EX5601-T0 ubootmod
The ubootmod bootlaoder for EX5601-T0 uses two partitions
in ubi to store enviroment variables. so proper config
is needed.
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Valerio 'ftp21' Mancini [Wed, 4 Oct 2023 09:43:25 +0000 (11:43 +0200)]
mediatek: add Zyxel EX5601-T0 with uboot custom partition
The flash procedure is similar to the Xiaomi AX6000 router.
Load openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb from original Zyxel U-Boot:
tftpboot openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
bootm 0x46000000
Load mtd-rw
insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1
Format ubi and create ubootenv partitions
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
Copy openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb to /tmp and create recovery partition.
If your recovery image is larger than 10MiB, size the recovery partition accordingly to make it fit.
ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
Copy preloader and uboot to /tmp and write them in the mtd
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip
Now write the firmware:
sysupgrade -n /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-squashfs-sysupgrade.itb
To create a correct BL2, I had to add a profile for 'spim:4k+256' as I could not find a way to value the variable 'NAND_TYPE'.
Features and fixes from hitech95 tree has been squashed, I'm attaching his commit message:
The Power LED was not working correctly and not reacting
to the boot process and statuses.
The board has space (footprint) for an unpopulated Zigbee chip,
while we dont know the device model having this chip populated
we have to assure that the common dts doesnt enable
interfaces that share pins with such device.
In this instance the PCIe and the uart1 and uart2 are disabled.
Some of the control PCIE pins seems to be used for the Zigbee chip,
UART1 seems to be used as a flash port while UART2 should be the
main comunication interface of Zigbee chip.
The Zigbee chip should be a EFR32MG21. But the pins used for UART
seems to be not on standard PINS used by other adapters.
So it cannot run firmwares shared on the web.
But it should be possible to build a custom firmware with
the corrtect pinmux.
This commit also contains the following squashed commit from hitech95
- mediatek: fix sysupgrade for Zyxel EX7601-T0 ubootmod
Changes and fixes added in common board:
- added aliases for boot status leds.
- added aliases for the mac-label-device.
- added pin claims for core features (MDIO and UART 0)
- added default LEDs configuration (01_leds)
- added default network configuration (02_network)
- added missing kmod-usb3 module for USB3
- fixed LED names
- fixed reset pin for SLIC chip
- removed unused pinmux configurations and devices
- fix LAN (switch) port numbering
- using nvmem cells for wifi eeprom, dropping deprecated "mediatek,mtd-eeprom"
- proper factory partition and mac address handling
- cleaned up spi_nand sections and partition
Changes and fixxes added in stock layout:
- added NMBM, if u-boot has it, the kernel must be informed.
Co-authored-by: Nicolò Veronese <nicveronese@gmail.com>
Co-developed-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Valerio 'ftp21' Mancini [Sat, 26 Aug 2023 22:01:58 +0000 (00:01 +0200)]
uboot-mediatek: add initial Zyxel EX5601-T0 support
Flash procedure is described in next commit.
TLDR:
Copy preloader and uboot to /tmp and write them in the mtd.
This will also require new UBI partition and
volumes to boot openwrt.
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip
Changelist:
- Added profile for 4k+256 SPI NAND_TYPE
- Added basic Zyxel EX5601-T0 uboot profile
Backported from hitech95 branch:
- Button RESET pin fix
- Button WPS pin fix
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Daniel Golle [Sat, 25 Nov 2023 03:20:50 +0000 (03:20 +0000)]
mediatek: remove DTS property added by mistake
Remove bogus 'phy-handle = <&phy0>;', an undefined reference.
Fixes: c8c2f52262 ("mediatek: add support for Zbtlink ZBT-Z8102AX")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Mikhail Zhilkin [Sun, 12 Nov 2023 07:58:26 +0000 (07:58 +0000)]
ramips: add support for Sercomm CPJ routers
This commit adds support for following wireless routers:
- Rostelecom RT-FL-1 (Serсomm RT-FL-1)
- Rostelecom S1010 (Serсomm S1010.RT)
The devices are almost identical and the only difference is one bit in the
factory image PID (thanks to Maximilian Weinmann <x1@disroot.org>
(@MaxS0niX) for the info and idea to make one PR for two devices at once).
Devices specification
---------------------
SoC: MediaTek MT7620A, MIPS
RAM: 64 MB
Flash: 16 MB SPI NOR
Wireless 2.4: MT7620 (b/g/n, 2x2)
Wireless 5: MT7612EN (a/n/ac, 2x2)
Ethernet: 5xFE (WAN, LAN1-4)
BootLoader: U-Boot
Buttons: 2 (wps, reset)
LEDs: 1 amber and 1 green status GPIO leds
5 green ethernet GPIO leds
1 green GPIO 2.4 GHz WLAN led
1 green PHY 5 GHz WLAN led
1 green unmanaged power led
USB ports: No
Power: 12 VDC, 1 A
Connector: Barrel
OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
before file extension)
2. Upload and update the firmware via the original web interface
3. Wait until green status led stops blinking (can take several minutes)
4. Login to OpenWrt initramsfs. It's recommended to make a backup of the
mtd partitions at this point.
4. Perform sysupgrade using the following command (or use Luci):
sysupgrade -n sysupgrade.bin
5. Wait until green status les stops blinking (can take several minutes)
6. Mission acomplished
Return to Stock
---------------
Option 1. Restore firmware Slot1 from a backup (firmware2.bin):
cd /tmp
mtd -e Firmware2 write firmware2.bin Firmware2
printf 1 | dd bs=1 seek=$((0x18007)) count=1 of=/dev/mtdblock2
reboot
Option 2. Decrypt, ungzip and split stock firmware image into the parts,
take Slot1 parts (kernel2.bin, rootfs2.bin) and write them:
cd /tmp
mtd -e Kernel2 write kernel2.bin Kernel2
mtd -e RootFS2 write rootfs2.bin RootFS2
printf 1 | dd bs=1 seek=$((0x18007)) count=1 of=/dev/mtdblock2
reboot
More about stock firmware decryption:
Link: https://github.com/Psychotropos/sercomm_fwutils/
Debricking
----------
Use sercomm-recovery tool. You can use "ALL" mtd partition backup as a
recovery image.
Link: https://github.com/danitool/sercomm-recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 48:3e:xx:xx:xx:1e | label |
| LAN | 48:3e:xx:xx:xx:1e | label |
| WAN | 48:3e:xx:xx:xx:28 | label+10 |
| WLAN 2g | 48:3e:xx:xx:xx:20 | label+2 |
| WLAN 5g | 48:3e:xx:xx:xx:24 | label+6 |
+---------+-------------------+-----------+
Co-authored-by: Vadzim Vabishchevich <bestmc2009@gmail.com>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Mikhail Zhilkin [Sun, 12 Nov 2023 07:56:08 +0000 (07:56 +0000)]
ramips: mt7620: drop unnecessary trailing tabs
Let's tidy up a bit (drop unnecessary trailing tabs).
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Mikhail Zhilkin [Sun, 12 Nov 2023 07:52:45 +0000 (07:52 +0000)]
ramips: sercomm.mk: make common recipe to set a bit in pid
This commit makes a common recipe to set bit in Sercomm factory pid since
this is necessary for several devices (WiFire S1500.nbn, Rostelecom
RT-FL-1) at different offsets.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Mikhail Zhilkin [Sun, 12 Nov 2023 07:46:11 +0000 (07:46 +0000)]
scripts: sercomm-pid.py: use uppercase hwid in pid
Sercomm uses uppercase for hexadecimal representation of the device
hardware IDs in factory image PID. This commit brings the sercomm-pid.py
script into compliance with the original Sercomm algorithm.
Example
-------
+--------+-------------+-----------+-------------+
| Device | PID (before | PID | PID (after |
| HWID | the commit) | (Sercomm) | the commit) |
+--------+-------------+-----------+-------------+
| CPJ | 43 50 4a | 43 50 4A | 43 50 4A |
+--------+-------------+-----------+-------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Jitao Lu [Tue, 21 Nov 2023 14:46:11 +0000 (22:46 +0800)]
linux-firmware: intel: add firmware for AX101
iwlwifi from 6.5 supports API version up to 83, but 81 is the latest one
available from linux-firmware
20230804.
Signed-off-by: Jitao Lu <dianlujitao@gmail.com>
Robert Marko [Fri, 24 Nov 2023 17:42:55 +0000 (18:42 +0100)]
ipq40xx: refresh patches
CI reported that ipq40xx needed a refresh, so lets refresh it.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Daniel Golle [Mon, 20 Nov 2023 20:23:42 +0000 (20:23 +0000)]
mediatek: add support for Zbtlink ZBT-Z8102AX
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by
Ian Ishmael C. Oderon.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Christian Marangi [Sun, 19 Nov 2023 11:52:55 +0000 (12:52 +0100)]
generic: 6.1: backport upstream Aquantia PHY firmware loader patches
Backport merged upstream patch that adds support for firmware loader
from NVMEM or attached filesystem for Aquantia PHYs.
Refresh all kernel patches affected by this change.
Also update the path for aquantia .ko that got moved to dedicated
directory upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rosen Penev [Mon, 13 Nov 2023 20:14:37 +0000 (12:14 -0800)]
realtek: convert to nvmem-layout
nvmem-cells is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
John Audia [Mon, 20 Nov 2023 13:23:17 +0000 (08:23 -0500)]
kernel: bump 5.15 to 5.15.139
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.139
Removed upstreamed:
backport-5.15/830-v6.6-2-leds-turris-omnia-Drop-unnecessary-mutex-locking.patch[1]
backport-5.15/830-v6.7-1-leds-turris-omnia-Do-not-use-SMBUS-calls.patch[2]
x86/patches-5.15/120-hwrng-geode-fix-accessing-registers.patch[3]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.139&id=
aec3706971b332af8321b2beccba981b8061489a
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.139&id=
893eedf596dd81c7a7f0cd80b345956ae000eab9
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.139&id=
a5c83c8043d70b9a28d1bd78a2dbbab340f43889
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Mon, 20 Nov 2023 12:15:50 +0000 (07:15 -0500)]
kernel: bump 6.1 to 6.1.63
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.63
Removed upstreamed:
generic/backport-6.1/815-v6.6-2-leds-turris-omnia-Drop-unnecessary-mutex-locking.patch
generic/backport-6.1/815-v6.7-1-leds-turris-omnia-Do-not-use-SMBUS-calls.patch
ixp4xx/patches-6.1/0007-watchdog-ixp4xx-Make-sure-restart-always-works.patch
Manually rebased:
bcm27xx/patches-6.1/950-0606-hwrng-bcm2835-sleep-more-intelligently.patch
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.63&id=
7d0e60e4ff840e97fb18afb2a7344442c10a6fdf
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.63&id=
63cdeb20ee3bfef820b045b8d3b8395f9f815a74
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.63&id=
8803da01fe1b4ca3d37745283f7e73c6c2558c0c
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Daniel Linjama [Thu, 2 Mar 2023 09:05:22 +0000 (11:05 +0200)]
ath79: add support for D-Link COVR-P2500 A1
Specifications:
* QCA9563, 16 MiB flash, 128 MiB RAM, 2T2R 802.11n
* QCA9886 2T2R 801.11ac Wave 2
* QCA7550 Homeplug AV2 1300
* AR8337, 3 Gigabit ports (1, 2: LAN; 3: WAN)
To make use of PLC functionality, firmware needs to be
provided via plchost (QCA7550 comes without SPI NOR),
patched with the Network Password and MAC.
Flashing via OEM Web Interface
* Flash 'factory.bin' using web-interface
* Wait until firmware succesfully installed and device booted
* Hold down reset button to reset factory defaults (~10 seconds)
Flashing via Recovery Web Interface:
* Hold down reset button during power-on (~10 seconds)
* Recovery Web UI is at 192.168.0.50, no DHCP.
* Flash 'recovery.bin' with
scripts/flashing/dlink_recovery_upload.py
(Recovery Web UI does not work with modern OSes)
Return to stock
* Hold down reset button during power-on (~10 seconds)
* Recovery Web UI is at 192.168.0.50, no DHCP.
* Flash unencrypted stock firmware with
scripts/flashing/dlink_recovery_upload.py
(Recovery Web UI does not work with modern OSes)
Co-developed-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Signed-off-by: Daniel Linjama <daniel@dev.linjama.com>
Hauke Mehrtens [Wed, 22 Nov 2023 23:15:40 +0000 (00:15 +0100)]
firmware-utils: Fix PKG_MIRROR_HASH
This fixes the mirror hash to the version of the file uploaded to the
download mirror and which my build calculated.
Fixes: b117e7244f9e ("firmware-utils: update to Git HEAD (2023-11-21)")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Wed, 22 Nov 2023 23:13:52 +0000 (00:13 +0100)]
tools: firmware-utils: Fix PKG_MIRROR_HASH
This fixes the mirror hash to the version of the file uploaded to the
download mirror and which my build calculated.
Fixes: 59a66d3c9b2a ("firmware-utils: update to Git HEAD (2023-11-21)")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Sat, 11 Nov 2023 02:52:20 +0000 (18:52 -0800)]
mvebu: remove mac-address-increment
It's deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rani Hod [Wed, 22 Nov 2023 17:38:06 +0000 (19:38 +0200)]
mediatek: fiilogic: device tree `switch@1f` fix
Quite a few `fiilogic` devices use the `mt7531` switch.
Some of them have a DT node that looks like:
```
switch: switch@0 {
compatible = "mediatek,mt7531";
reg = <31>;
...
};
```
This commit changes the DT node name to `switch@1f`.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Rosen Penev [Tue, 14 Nov 2023 03:52:47 +0000 (19:52 -0800)]
ipq806x: add missing interrupt-controller
Fixes dtc warnings
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sat, 11 Nov 2023 22:59:41 +0000 (14:59 -0800)]
ipq806x: remove mac-address-increment
It's deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sat, 11 Nov 2023 03:42:31 +0000 (19:42 -0800)]
lantiq: remove mac-address-increment
It's deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sat, 11 Nov 2023 03:33:27 +0000 (19:33 -0800)]
bmips: remove mac-address-increment
It's deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Christian Marangi [Tue, 21 Nov 2023 22:57:44 +0000 (23:57 +0100)]
Revert "mpc85xx: replace user space MAC with nvmem"
This reverts commit
931fcf61891f14dffccd0ad5dfdf7d84460ff9f2.
The definition is wrong and require mac-base compatible. Also it's not
clear if it's correct to use 0xc for mac size.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rosen Penev [Sun, 19 Nov 2023 01:23:48 +0000 (17:23 -0800)]
mpc85xx: replace user space MAC with nvmem
Possible now that NVMEM supports ASCII.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sat, 11 Nov 2023 02:57:43 +0000 (18:57 -0800)]
mpc85xx: remove mac-address-increment
It's deprecated
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Tue, 14 Nov 2023 01:09:42 +0000 (17:09 -0800)]
mpc85xx: fix dtc warning
States to remove the linux prefix
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sat, 11 Nov 2023 02:42:52 +0000 (18:42 -0800)]
octeon: remove mac-address-increment
It's deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rafał Miłecki [Tue, 21 Nov 2023 20:16:42 +0000 (21:16 +0100)]
firmware-utils: update to Git HEAD (2023-11-21)
12bf1a9 lxlfw: support certificate & signature blobs
eaf2ea2 lxlfw: support extracting image
d770cab lxlfw: support embedding blobs
16fa890 lxlfw: fix struct lxl_hdr attribute
8e149e4 lxlfw: move code copying data to helper function
3b114de lxlfw: move code opening LXL to helper function
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Wed, 15 Nov 2023 08:04:47 +0000 (09:04 +0100)]
kernel: drop "mac-address-increment-byte" DT property support
This downstream DT property is not used by any DTS file anymore.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Tue, 21 Nov 2023 15:30:22 +0000 (16:30 +0100)]
firmware-utils: update to Git HEAD (2023-11-21)
1d42292d8063 tplink-safeloader: Add TP-Link Archer A6 V3.20
3338f5389d72 tplink-safeloader: add TL-WPA8635P v3
17ca5eeb1c10 tplink-safeloader: add TL-WPA8631P v4
f730ad2fa0b4 bcmblob: new tool for reading Broadcom's BLOBs
cb1ddac98124 firmware-utils: fix typo in error message when no OpenSSL library found
916633160dc9 bcmclm: new tool for reading Broadcom's CLM data
a2d49fb1e188 tplink-safeloader: add RU support-list entry for Archer C6U v1
bb12cf5c3fa9 tplink-safeloader: Add support for TP-Link Deco M5 The special_id values are the same for EU and Asian models, and they apply to all models: v1, v2, and v3. They are not sorted as they are currently in the same order as extracted from the official firmware image.
9e2de8515be1 tplink-safeloader: add EAP610 v3 and EAP613 v1
a170683c0e11 firmware-utils: fix use of NULL string progname
89875fc18b57 tplink-safeloader: CPE510: add Canadian support
9e211d2980fe mktplinkfw2: add support to extract bootloader images
c18f662f3c74 mktplinkfw2: add support to pack bootloader
3dc133915f87 mktplinkfw2: show exact exceed bytes when the image is to big
d16ff798d58a tplink-safeloader: WPA8631: add v4 AU, US
0fa1cc51013f zytrx: add LTE5398-M904
635466123429 firmware-utils: ptgen: add SiFive GPT partition support
ba5bc4e1ae9d add dlink-sge-image for D-Link devices by SGE
3b114de29cf7 lxlfw: move code opening LXL to helper function
8e149e480391 lxlfw: move code copying data to helper function
16fa89076122 lxlfw: fix struct lxl_hdr attribute
d770cab82e58 lxlfw: support embedding blobs
eaf2ea28dbe6 lxlfw: support extracting image
12bf1a99bd6e lxlfw: support certificate & signature blobs
Fixes: https://github.com/openwrt/openwrt/issues/12939
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Felix Fietkau [Tue, 21 Nov 2023 06:35:48 +0000 (07:35 +0100)]
umdns: update to Git HEAD (2023-11-21)
9040335e102b interface: fix interface memory corruption
b1e023eda358 add udebug support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 20 Nov 2023 22:03:48 +0000 (23:03 +0100)]
udebug: update to Git HEAD (2023-11-20)
759d9404034b ring: add missing fread return code check
Signed-off-by: Felix Fietkau <nbd@nbd.name>
projects / openwrt / staging / linusw.git / log