Oliver Neukum [Fri, 27 Apr 2007 18:54:57 +0000 (20:54 +0200)]
USB: suspend support for usb serial
this implements generic support for suspend/resume for usb serial.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Chandra Seetharaman [Thu, 12 Jul 2007 16:30:05 +0000 (17:30 +0100)]
dm mpath: rdac
This patch supports LSI/Engenio devices in RDAC mode. Like dm-emc
it requires userspace support. In your multipath.conf file you must have:
path_checker rdac
hardware_handler "1 rdac"
prio_callout "/sbin/mpath_prio_tpc /dev/%n"
And you also then must have a updated multipath tools release which
has rdac support.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jonathan Brassow [Thu, 12 Jul 2007 16:29:15 +0000 (17:29 +0100)]
dm raid1: handle log failure
When writing to a mirror, the log must be updated first. Failure
to update the log could result in the log not properly reflecting
the state of the mirror if the machine should crash.
We change the return type of the rh_flush function to give us
the ability to check if a log write was successful. If the
log write was unsuccessful, we fail the writes to avoid the
case where the log does not properly reflect the state of the
mirror.
A follow-up patch - which is dependent on the ability to
requeue I/O's to core device-mapper - will requeue the I/O's
for retry (allowing the mirror to be reconfigured.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jonathan Brassow [Thu, 12 Jul 2007 16:29:04 +0000 (17:29 +0100)]
dm raid1: handle resync failures
Device-mapper mirroring currently takes a best effort approach to
recovery - failures during mirror synchronization are completely ignored.
This means that regions are marked 'in-sync' and 'clean' and removed
from the hash list. Future reads and writes that query the region
will incorrectly interpret the region as in-sync.
This patch handles failures during the recovery process. If a failure
occurs, the region is marked as 'not-in-sync' (aka RH_NOSYNC) and added
to a new list 'failed_recovered_regions'.
Regions on the 'failed_recovered_regions' list are not marked as 'clean'
upon removal from the list. Furthermore, if the DM_RAID1_HANDLE_ERRORS
flag is set, the region is marked as 'not-in-sync'. This action prevents
any future read-balancing from choosing an invalid device because of the
'not-in-sync' status.
If "handle_errors" is not specified when creating a mirror (leaving the
DM_RAID1_HANDLE_ERRORS flag unset), failures will be ignored exactly as they
would be without this patch. This is to preserve backwards compatibility with
user-space tools, such as 'pvmove'. However, since future read-balancing
policies will rely on the correct sync status of a region, a user must choose
"handle_errors" when using read-balancing.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jonathan Brassow [Thu, 12 Jul 2007 16:28:42 +0000 (17:28 +0100)]
dm: add ratelimit logging macros
Add ratelimit extension to dm logging macros.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stefan Bader [Thu, 12 Jul 2007 16:28:33 +0000 (17:28 +0100)]
dm: disable barriers
This patch causes device-mapper to reject any barrier requests. This is done
since most of the targets won't handle this correctly anyway. So until the
situation improves it is better to reject these requests at the first place.
Since barrier requests won't get to the targets, the checks there can be
removed.
Cc: stable@kernel.org
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jonathan Brassow [Thu, 12 Jul 2007 16:28:25 +0000 (17:28 +0100)]
dm raid1: clear region outside spinlock
A clear_region function is permitted to block (in practice, rare) but gets
called in rh_update_states() with a spinlock held.
The bits being marked and cleared by the above functions are used
to update the on-disk log, but are never read directly. We can
perform these operations outside the spinlock since the
bits are only changed within one thread viz.
- mark_region in rh_inc()
- clear_region in rh_update_states().
So, we grab the clean_regions list items via list_splice() within the
spinlock and defer clear_region() until we iterate over the list for
deletion - similar to how the recovered_regions list is already handled.
We then move the flush() call down to ensure it encapsulates the changes
which are done by the later calls to clear_region().
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Milan Broz [Thu, 12 Jul 2007 16:28:13 +0000 (17:28 +0100)]
dm snapshot: permit invalid activation
Allow invalid snapshots to be activated instead of failing.
This allows userspace to reinstate any given snapshot state - for
example after an unscheduled reboot - and clean up the invalid snapshot
at its leisure.
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Milan Broz [Thu, 12 Jul 2007 16:28:00 +0000 (17:28 +0100)]
dm snapshot: fix invalidation deadlock
Process persistent exception store metadata IOs in a separate thread.
A snapshot may become invalid while inside generic_make_request().
A synchronous write is then needed to update the metadata while still
inside that function. Since the introduction of
md-dm-reduce-stack-usage-with-stacked-block-devices.patch this has to
be performed by a separate thread to avoid deadlock.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jun'ichi Nomura [Thu, 12 Jul 2007 16:27:45 +0000 (17:27 +0100)]
dm io: fix panic on large request
bio_alloc_bioset() will return NULL if 'num_vecs' is too large.
Use bio_get_nr_vecs() to get estimation of maximum number.
Cc: stable@kernel.org
Signed-off-by: "Jun'ichi Nomura" <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Milan Broz [Thu, 12 Jul 2007 16:27:24 +0000 (17:27 +0100)]
dm raid1: fix status
Fix mirror status line broken in dm-log-report-fault-status.patch:
- space missing between two words
- placeholder ("0") required for compatibility with a subsequent patch
- incorrect offset parameter
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alasdair G Kergon [Thu, 12 Jul 2007 16:27:01 +0000 (17:27 +0100)]
dm: remove duplicate module name from error msgs
Remove explicit module name from messages as the macro now includes it
automatically.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alasdair G Kergon [Thu, 12 Jul 2007 16:26:47 +0000 (17:26 +0100)]
dm delay: cleanup
Use setup_timer().
Replace semaphore with mutex.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alasdair G Kergon [Thu, 12 Jul 2007 16:26:32 +0000 (17:26 +0100)]
dm: use kmem_cache macro
Use new KMEM_CACHE() macro and make the newly-exposed structure names more
meaningful. Also remove some superfluous casts and inlines (let a modern
compiler be the judge).
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alasdair G Kergon [Thu, 12 Jul 2007 16:26:19 +0000 (17:26 +0100)]
dm: bio_list prefetch removal
Remove dubious prefetch from bio_list_for_each() macro.
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 12 Jul 2007 21:17:12 +0000 (14:17 -0700)]
Merge branch 'devel' of /home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (50 commits)
[ARM] sa1100: remove boot time RTC initialisation
[ARM] sa1100: stop doing our own rtc management over suspend
[ARM] 4474/1: Do not check the PSR_F_BIT in valid_user_regs
[ARM] 4473/2: Take the HWCAP definitions out of the elf.h file
[ARM] pxa: move platform devices to separate header file
[ARM] pxa: move device registration into CPU-specific file
[ARM] pxa: remove boot time RTC initialisation
[ARM] pxa: stop doing our own rtc management over suspend
[ARM] 4451/1: pxa: make dma.c generic and remove cpu specific dma code
[ARM] 4450/1: pxa: add pxa25x_init_irq() and pxa27x_init_irq()
[ARM] 4440/1: PXA: enable the checking of ICIP2 for IRQs
[ARM] 4438/1: PXA: remove #ifdef .. #endif from pxa_gpio_demux_handler()
[ARM] 4437/1: PXA: move the GPIO IRQ initialization code to pxa_init_irq_gpio()
[ARM] 4436/1: PXA: move low IRQ initialization code to pxa_init_irq_low()
[ARM] 4435/1: PXA: remove PXA_INTERNAL_IRQS
[ARM] 4434/1: PXA: remove PXA_IRQ_SKIP
[ARM] pxa: Fix PXA27x suspend type validation, remove pxa_pm_prepare()
[ARM] pxa: move pm_ops structure into CPU specific files
[ARM] pxa: introduce cpu_is_pxaXXX macros
[ARM] pxa: remove MMC register defines from pxa-regs.h
...
Linus Torvalds [Thu, 12 Jul 2007 20:46:48 +0000 (13:46 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/selinux-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
security: unexport mmap_min_addr
SELinux: use SECINITSID_NETMSG instead of SECINITSID_UNLABELED for NetLabel
security: Protection for exploiting null dereference using mmap
SELinux: Use %lu for inode->i_no when printing avc
SELinux: allow preemption between transition permission checks
selinux: introduce schedule points in policydb_destroy()
selinux: add selinuxfs structure for object class discovery
selinux: change sel_make_dir() to specify inode counter.
selinux: rename sel_remove_bools() for more general usage.
selinux: add support for querying object classes and permissions from the running policy
Linus Torvalds [Thu, 12 Jul 2007 20:42:43 +0000 (13:42 -0700)]
Merge /pub/scm/linux/kernel/git/davej/cpufreq
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix sysfs_create_file return value handling
[CPUFREQ] ondemand: fix tickless accounting and software coordination bug
[CPUFREQ] ondemand: add a check to avoid negative load calculation
[CPUFREQ] Keep userspace governor quiet when it is not being used
[CPUFREQ] Longhaul - Proper register access
[CPUFREQ] Kconfig powernow-k8 driver should depend on ACPI P-States driver
[CPUFREQ] Longhaul - Replace ACPI functions with direct I/O
[CPUFREQ] Longhaul - Remove duplicate multipliers
[CPUFREQ] Longhaul - Embedded "conservative"
[CPUFREQ] acpi-cpufreq: Proper ReadModifyWrite of PERF_CTL MSR
[CPUFREQ] check return value of sysfs_create_file
[CPUFREQ] Longhaul - Check ACPI "BM DMA in progress" bit
[CPUFREQ] Longhaul - Move old_ratio to correct place
[CPUFREQ] Longhaul - VT8237 support
[CPUFREQ] Longhaul - Use all kinds of support
[CPUFREQ] powernow-k8: clarify number of cores.
Linus Torvalds [Thu, 12 Jul 2007 20:41:54 +0000 (13:41 -0700)]
Merge /pub/scm/linux/kernel/git/davej/agpgart
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] Hand off AGP maintainence.
Linus Torvalds [Thu, 12 Jul 2007 20:41:29 +0000 (13:41 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Support multiple CPUs going through OS_MCA
[IA64] silence GCC ia64 unused variable warnings
[IA64] prevent MCA when performing MMIO mmap to PCI config space
[IA64] add sn_register_pmi_handler oemcall
[IA64] Stop bit for brl instruction
[IA64] SN: Correct ROM resource length for BIOS copy
[IA64] Don't set psr.ic and psr.i simultaneously
Linus Torvalds [Thu, 12 Jul 2007 20:40:57 +0000 (13:40 -0700)]
Merge /pub/scm/linux/kernel/git/gregkh/pci-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
Linus Torvalds [Thu, 12 Jul 2007 20:40:20 +0000 (13:40 -0700)]
Merge /pub/scm/linux/kernel/git/gregkh/driver-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (61 commits)
sysfs: add parameter "struct bin_attribute *" in .read/.write methods for sysfs binary attributes
sysfs: make directory dentries and inodes reclaimable
sysfs: implement sysfs_get_dentry()
sysfs: move sysfs_drop_dentry() to dir.c and make it static
sysfs: restructure add/remove paths and fix inode update
sysfs: use sysfs_mutex to protect the sysfs_dirent tree
sysfs: consolidate sysfs spinlocks
sysfs: make kobj point to sysfs_dirent instead of dentry
sysfs: implement sysfs_find_dirent() and sysfs_get_dirent()
sysfs: implement SYSFS_FLAG_REMOVED flag
sysfs: rename sysfs_dirent->s_type to s_flags and make room for flags
sysfs: make sysfs_drop_dentry() access inodes using ilookup()
sysfs: Fix oops in sysfs_drop_dentry on x86_64
sysfs: use singly-linked list for sysfs_dirent tree
sysfs: slim down sysfs_dirent->s_active
sysfs: move s_active functions to fs/sysfs/dir.c
sysfs: fix root sysfs_dirent -> root dentry association
sysfs: use iget_locked() instead of new_inode()
sysfs: reorganize sysfs_new_indoe() and sysfs_create()
sysfs: fix parent refcounting during rename and move
...
Linus Torvalds [Thu, 12 Jul 2007 20:38:50 +0000 (13:38 -0700)]
Merge branch 'upstream-linus' of /linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (21 commits)
libata: remove irq_on from ata_bus_reset() and ata_std_postreset()
ata_piix: kill incorrect invalid map value warning
libata: add another Maxtor drive with broken NCQ to the list
[libata] sata_mv: Fix and clean up per-chip-generation tests
[libata] sata_mv: Convert to new exception handling (EH) infrastructure
[libata] sata_mv: minor bug fixes, enhancements, and cleanups (prep for new EH)
[libata] sata_mv: Minor cleanups and renaming, preparing for new EH & NCQ
libata-link: add PMP related ATA constants
libata-link: separate out ata_eh_handle_dev_fail()
pata_hpt3x3: fix DMA Kconfig option to actually have a hope of working
Add Hitachi HDS7250SASUN500G 0621KTAWSD to NCQ blacklist
pata_scc.c: Workaround for errata A308
libata: add FUJITSU MHV2080BH to NCQ blacklist
pata_hpt3x3: major reworking and testing
libata: clean up horkage handling
libata: quirk IOMEGA ZIP 250 ATAPI FLOPPY
libata: simplify PCI legacy SFF host handling
pata_mpc52xx: suspend/resume support
sata_promise: SATA hotplug support, take 2
pata_sis: FIFO whack
...
Linus Torvalds [Thu, 12 Jul 2007 20:31:22 +0000 (13:31 -0700)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (183 commits)
[TG3]: Update version to 3.78.
[TG3]: Add missing NVRAM strapping.
[TG3]: Enable auto MDI.
[TG3]: Fix the polarity bit.
[TG3]: Fix irq_sync race condition.
[NET_SCHED]: ematch: module autoloading
[TCP]: tcp probe wraparound handling and other changes
[RTNETLINK]: rtnl_link: allow specifying initial device address
[RTNETLINK]: rtnl_link API simplification
[VLAN]: Fix MAC address handling
[ETH]: Validate address in eth_mac_addr
[NET]: Fix races in net_rx_action vs netpoll.
[AF_UNIX]: Rewrite garbage collector, fixes race.
[NETFILTER]: {ip, nf}_conntrack_sctp: fix remotely triggerable NULL ptr dereference (CVE-2007-2876)
[NET]: Make all initialized struct seq_operations const.
[UDP]: Fix length check.
[IPV6]: Remove unneeded pointer idev from addrconf_cleanup().
[DECNET]: Another unnecessary net/tcp.h inclusion in net/dn.h
[IPV6]: Make IPV6_{RECV,2292}RTHDR boolean options.
[IPV6]: Do not send RH0 anymore.
...
Fixed up trivial conflict in Documentation/feature-removal-schedule.txt
manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Russell King [Thu, 12 Jul 2007 20:30:18 +0000 (21:30 +0100)]
Merge branches 'at91', 'davinci', 'imx', 'iop', 'ixp', 'ks8695', 'misc', 'pxa' and 's3c' into devel
Russell King [Thu, 12 Jul 2007 20:29:45 +0000 (21:29 +0100)]
[ARM] sa1100: remove boot time RTC initialisation
The RTC library code contains everything necessary to set the
system time from the RTC; for similar reasons as the previous
commit, it's far better to let the RTC library code sort this
out rather than implement something which might not be
appropriate for everyone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 12 Jul 2007 20:29:06 +0000 (21:29 +0100)]
[ARM] sa1100: stop doing our own rtc management over suspend
Remove the RTC management over a suspend/resume cycle. As per the
corresponding PXA patch, the RTC library code handles updating
system time on resume.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Thu, 12 Jul 2007 20:28:54 +0000 (13:28 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Rename PC speaker code
[MIPS] Don't use genrtc.
[MIPS] Remove unused time.c for swarm
[MIPS] Sparse: Use NULL for pointer
[MIPS] Fix a sparse warning in arch/mips/pci/pci.c
[MIPS] SMTC: Interrupt mask backstop hack
[MIPS] separate platform_device registration for VR41xx RTC
[MIPS] Separate platform_device registration for VR41xx GPIO
[MIPS] MIPSsim: Fix build.
[MIPS] separate platform_device registration for VR41xx serial interface
[MIPS] Include cacheflush.h in uncache.c
[MIPS] Cleanup tlbdebug.h
[MIPS] Change names of local variables to silence sparse (part 2)
[MIPS] Workaround for a sparse warning in include/asm-mips/io.h
[MIPS] RM: Use only phyiscal address for 82596 and 53c710
[MIPS] Hydrogen3: Remove remaining bits of code.
[MIPS] DEC: Fix modpost warning.
Revert "[MIPS] DEC: Fix modpost warning."
[MIPS] Fix resume for 64K page size on R4000 class processors.
Linus Torvalds [Thu, 12 Jul 2007 20:25:24 +0000 (13:25 -0700)]
Merge /linux/kernel/git/cooloney/blackfin-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (30 commits)
Blackfin serial driver: supporting BF548-EZKIT serial port
Video Console: Blackfin doesnt support VGA console
Blackfin arch: Add peripheral io API to gpio header file
Blackfin arch: set up gpio interrupt IRQ_PJ9 for BF54x ATAPI PATA driver
Blackfin arch: add missing CONFIG_LARGE_ALLOCS when upstream merging
Blackfin arch: as pointed out by Robert P. J. Day, update the CPU_FREQ name to match current Kconfig
Blackfin arch: extract the entry point from the linked kernel
Blackfin arch: clean up some coding style issues
Blackfin arch: combine the common code of free_initrd_mem and free_initmem
Blackfin arch: Add Support for Peripheral PortMux and resouce allocation
Blackfin arch: use PAGE_SIZE when doing aligns rather than hardcoded values
Blackfin arch: fix bug set dma_address properly in dma_map_sg
Blackfin arch: Disable CACHELINE_ALIGNED_L1 for BF54x by default
Blackfin arch: Port the dm9000 driver to Blackfin by using the correct low-level io routines
Blackfin arch: There is no CDPRIO Bit in the EBIU_AMGCTL Register of BF54x arch
Blackfin arch: scrub dead code
Blackfin arch: Fix Warning add some defines in BF54x header file
Blackfin arch: add BF54x missing GPIO access functions
Blackfin arch: Some memory and code optimizations - Fix SYS_IRQS
Blackfin arch: Enable BF54x PIN/GPIO interrupts
...
Linus Torvalds [Thu, 12 Jul 2007 20:25:00 +0000 (13:25 -0700)]
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (26 commits)
i2c-rpx: Remove
i2c-mpc: work around missing-9th-clock-pulse bug
i2c: New PMC MSP71xx TWI bus driver
i2c-savage4: Delete many unused defines
i2c/tsl2550: Speed up initialization
i2c: New bus driver for the TAOS evaluation modules
i2c-i801: Use the internal 32-byte buffer on ICH4+
i2c-i801: Various cleanups
i2c: Add support for the TSL2550
i2c-pxa: Support new-style I2C drivers
i2c-gpio: Make some internal functions static
i2c-gpio: Add support for new-style clients
i2c-iop3xx: Switch to static adapter numbering
i2c-sis5595: Resolve resource conflict with sis5595
matroxfb: Clean-up i2c header inclusions
i2c-nforce2: Add support for SMBus block transactions
i2c-mpc: Use i2c_add_numbered_adapter
i2c-mv64xxx: Use i2c_add_numbered_adapter
i2c-piix4: Add support for the ATI SB700
i2c: New DS1682 chip driver
...
Albert Lee [Sat, 7 Jul 2007 07:00:37 +0000 (15:00 +0800)]
libata: remove irq_on from ata_bus_reset() and ata_std_postreset()
It seems irq_on() in ata_bus_reset() and ata_std_postreset()
are leftover of the EDD reset. Remove them.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Tue, 10 Jul 2007 08:58:21 +0000 (17:58 +0900)]
ata_piix: kill incorrect invalid map value warning
The last two slots of MAP 00b of ich6m was incorrectly marked as
reserved. This is left over from converting the entry to allow 00b.
This causes no real problem. It only makes the driver print annoying
warning message. Fix it.
[patch also proferred by Pierre Tardy at the end of 2006 -jg]
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
drivers/ata/ata_piix.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Chuck Ebbert [Thu, 12 Jul 2007 18:37:19 +0000 (14:37 -0400)]
libata: add another Maxtor drive with broken NCQ to the list
Add another Maxtor 6B200M0 drive with broken NCQ to the list.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff Garzik [Thu, 12 Jul 2007 19:51:22 +0000 (15:51 -0400)]
[libata] sata_mv: Fix and clean up per-chip-generation tests
Due to a mistake in test logic, Gen-IIE chips were being treated as
Gen-II chips in some cases. Fix this, and in the process, clean up
IS_50XX/IS_60XX tests to the more uniform IS_GEN_{I,II,IIE} tests.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff Garzik [Thu, 12 Jul 2007 18:34:26 +0000 (14:34 -0400)]
[libata] sata_mv: Convert to new exception handling (EH) infrastructure
This makes hotplug, NCQ, etc. possible, and removes one of the few
remaining old-EH drivers.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff Garzik [Thu, 12 Jul 2007 18:30:19 +0000 (14:30 -0400)]
[libata] sata_mv: minor bug fixes, enhancements, and cleanups (prep for new EH)
* Continue replacing "CONSTANT & var" tests with "var & CONSTANT"
* Don't clear EDMA_CFG_NCQ_GO_ON_ERR on Gen-IIE, where that bit does
not exist
* Set I/O Id field in descriptor, where present. Appears to work
fine on all versions, even though queueing is still disabled.
* call pci_set_mwi(), to (a) make sure cacheline size is set properly,
and (b) enable MWI transactions
* Remove never-used handling of coalescing interrupt bits (these events
are always masked)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:58 +0000 (12:18 -0700)]
Remove old i386 setup code
This removes the old i386 setup code. This is done as a separate patch
to avoid breaking git bisect as some of the i386 code was also used by
the old x86-64 code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:57 +0000 (12:18 -0700)]
Use the new x86 setup code for x86-64; unify with i386
This unifies arch/*/boot (except arch/*/boot/compressed) between
i386 and x86-64, and uses the new x86 setup code for x86-64 as well.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:56 +0000 (12:18 -0700)]
Use the new x86 setup code for i386
This patch hooks the new x86 setup code into the Makefile machinery. It
also adapts boot/tools/build.c to a two-file (as opposed to three-file)
universe, and simplifies it substantially.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:55 +0000 (12:18 -0700)]
Linker script for the new x86 setup code
Linker script to define the layout of the new x86 setup code.
Includes assert for size overflow and a misaligned setup header.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:54 +0000 (12:18 -0700)]
Assembly header and main routine for new x86 setup code
The assembly header and initialization code, and the main() routine.
main.c also contains some miscellaneous very short routines.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:53 +0000 (12:18 -0700)]
Code for actual protected-mode entry
This is the code which actually does the switch to protected mode,
including all preparation. It is also responsible for invoking the
boot loader hooks, if present.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:52 +0000 (12:18 -0700)]
Video mode probing support for the new x86 setup code
Video mode probing for the new x86 setup code. This code breaks down
different drivers into modules. This code deliberately drops support
for a lot of the vendor-specific mode probing present in the assembly
version, since a lot of those probes have been found to be stale in
current versions of those chips -- frequently, support for those modes
have been dropped from recent video BIOSes due to space constraints,
but the video BIOS signatures are still the same.
However, additional drivers should be extremely straightforward to plug
in, if desirable.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:51 +0000 (12:18 -0700)]
Voyager support for the new x86 setup code
Voyager support for the new x86 setup code. This implements the same
functionality as the assembly version.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:50 +0000 (12:18 -0700)]
Memory probing support for the new x86 setup code
Probe memory (INT 15h: E820, E801, 88).
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:49 +0000 (12:18 -0700)]
MCA support for new x86 setup code
MCA probing support for the new x86 setup code. This implements the
same functionality as the assembly version.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:48 +0000 (12:18 -0700)]
EDD probing code for the new x86 setup code
Probe EDD and MBR signatures, in order to make it easier to map
physical hard drives to BIOS drives.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:47 +0000 (12:18 -0700)]
CPU features verification for the new x86 setup code
Verify that the CPU has enough features to run the kernel. This may
entail enabling features on some CPUs.
By doing this in the setup code we can be guaranteed to still be able to
write to the console through the BIOS.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:46 +0000 (12:18 -0700)]
Version string for the new x86 setup code
Module which only includes the kernel version string.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:45 +0000 (12:18 -0700)]
Console-writing code for the new x86 setup code
This implements writing text to the console, including printf().
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:44 +0000 (12:18 -0700)]
Command-line parsing code for the new x86 setup code
Simple command-line parser which allows us to access the kernel command
line from the setup code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:43 +0000 (12:18 -0700)]
APM probing code
APM probing code for the new x86 setup code. This implements the
same functionality as the assembly version.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:42 +0000 (12:18 -0700)]
A20 handling code
A20 handling code for the new x86 setup code. This implements the same
algorithms as the assembly version.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:41 +0000 (12:18 -0700)]
String-handling functions for the new x86 setup code.
strcmp(), memcpy(), memset(), as well as routines to copy to and from
other segments (as pointed to by fs and gs).
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:40 +0000 (12:18 -0700)]
Simple bitops for the new x86 setup code.
A simple collection of bitops for the new x86 setup code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:39 +0000 (12:18 -0700)]
Top header file for new x86 setup code
Top header file for the new x86 setup code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:38 +0000 (12:18 -0700)]
Header file to produce 16-bit code with gcc
gcc for i386 can be used with the assembly prefix ".code16gcc" to generate
16-bit (real-mode) code. This header file provides the assembly prefix.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:37 +0000 (12:18 -0700)]
x86-64: add symbolic constants for the boot segment selectors
Add symbolic constants for the segment selectors/GDT slots used by
the setup code, for consistency with i386.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:36 +0000 (12:18 -0700)]
x86-64: add CONFIG_PHYSICAL_ALIGN for consistency with i386
Add CONFIG_PHYSICAL_ALIGN (currently as a hardcoded constant) to provide
consistency with i386. This value is manifest in the bzImage header.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:35 +0000 (12:18 -0700)]
Make struct boot_params a real structure, and remove obsolete fields
Make struct boot_params a real structure, and remove the handling of
some obsolete fields, in particular hd*_info, which was only used by
the ST-506 driver, and likely to be wrong for that driver on any
modern BIOS.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:34 +0000 (12:18 -0700)]
Make definitions for struct e820entry and struct e820map consistent
Make definitions for struct e820entry and struct e820map
consistent between i386 and x86-64.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:33 +0000 (12:18 -0700)]
Define zero-page offset 0x1e4 as a scratch field, and use it
The relocatable kernel code needs a scratch field for the decompressor
to determine its own location. It was using a location inside
struct screen_info; reserve a free location and document it as scratch
instead.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Venki Pallipadi [Wed, 11 Jul 2007 19:18:32 +0000 (12:18 -0700)]
Use a new CPU feature word to cover features that are spread around
Some Intel features are spread around in different CPUID leafs like 0x5,
0x6 and 0xA. Make this feature detection code common across i386 and
x86_64.
Display Intel Dynamic Acceleration feature in /proc/cpuinfo. This feature
will be enabled automatically by current acpi-cpufreq driver.
Refer to Intel Software Developer's Manual for more details about the feature.
Thanks to hpa (H Peter Anvin) for the making the actual code detecting the
scattered features data-driven.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:31 +0000 (12:18 -0700)]
Clean up struct screen_info (<linux/screen_info.h>)
struct screen_info has unaligned members, it needs to be packed.
In the process, fix the naming of some of the members, which don't
belong in this structure but are part of it anyway.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:30 +0000 (12:18 -0700)]
x86 Kconfig: change X86_MINIMUM_CPU_MODEL to X86_MINIMUM_CPU_FAMILY
The X86_MINIMUM_CPU_MODEL name isn't really right, so change it to
X86_MINIMUM_CPU_FAMILY. Also, the default minimum should be 3, not 0.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:29 +0000 (12:18 -0700)]
Unify the CPU features vectors between i386 and x86-64
Unify the handling of the CPU features vectors between i386 and x86-64.
This also adopts the collapsing of features which are required at
compile-time into constant tests from x86-64 to i386.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:28 +0000 (12:18 -0700)]
include/asm-i386/boot.h: This is <asm/boot.h>, not <linux/boot.h>
include/asm-i386/boot.h incorrectly has the multiple include guards
as _LINUX_BOOT_H instead of _ASM_BOOT_H. Fix.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:27 +0000 (12:18 -0700)]
hd.c: remove BIOS/CMOS queries
An ST-506 disk these days is pretty much someone trying to pull ancient
data using an auxilliary controller. Pulling data from the BIOS or CMOS
is just plain wrong, since it's likely to be the primary OS disk... and
would be user-entered data anyway. Instead, require the user enters it
on the command line.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:26 +0000 (12:18 -0700)]
x86 setup: MAINTAINERS: formally take responsibility for the i386 boot code
Change MAINTAINERS to formally take responsibility for the i386 boot code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ralf Baechle [Thu, 12 Jul 2007 16:41:23 +0000 (17:41 +0100)]
[MIPS] Rename PC speaker code
While the PC speaker is wired up to the i8254 there is more to the i8254
than just the PC speaker so this code was getting in the way under its
current name.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Thu, 12 Jul 2007 16:41:21 +0000 (17:41 +0100)]
[MIPS] Don't use genrtc.
The only pseudo-legitimate MIPS user of genrtc was a systems that doesn't
have an RTC in hardware at all. At this point faking one is a little
pointless ...
Yoichi Yuasa [Thu, 7 Jun 2007 13:27:50 +0000 (22:27 +0900)]
[MIPS] Remove unused time.c for swarm
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Thu, 12 Jul 2007 16:49:49 +0000 (01:49 +0900)]
[MIPS] Sparse: Use NULL for pointer
This fixes a sparse warning:
arch/mips/kernel/traps.c:376:44: warning: Using plain integer as NULL pointer
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Thu, 12 Jul 2007 16:26:52 +0000 (01:26 +0900)]
[MIPS] Fix a sparse warning in arch/mips/pci/pci.c
Fixes this warning:
arch/mips/pci/pci.c:284:18: warning: symbol 'dev' shadows an earlier one
arch/mips/pci/pci.c:272:17: originally declared here
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Kevin D. Kissell [Thu, 12 Jul 2007 15:21:08 +0000 (16:21 +0100)]
[MIPS] SMTC: Interrupt mask backstop hack
To support multiple TC microthreads acting as "CPUs" within a VPE,
VPE-wide interrupt mask bits must be specially manipulated during
interrupt handling. To support legacy drivers and interrupt controller
management code, SMTC has a "backstop" to track and if necessary restore
the interrupt mask. This has some performance impact on interrupt service
overhead. Disable it only if you know what you are doing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Yoichi Yuasa [Fri, 11 May 2007 12:18:48 +0000 (21:18 +0900)]
[MIPS] separate platform_device registration for VR41xx RTC
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Yoichi Yuasa [Thu, 10 May 2007 13:21:35 +0000 (22:21 +0900)]
[MIPS] Separate platform_device registration for VR41xx GPIO
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Thu, 12 Jul 2007 16:41:14 +0000 (17:41 +0100)]
[MIPS] MIPSsim: Fix build.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Yoichi Yuasa [Tue, 8 May 2007 15:03:02 +0000 (00:03 +0900)]
[MIPS] separate platform_device registration for VR41xx serial interface
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Wed, 11 Jul 2007 15:55:40 +0000 (00:55 +0900)]
[MIPS] Include cacheflush.h in uncache.c
This fixes this sparse warning:
arch/mips/lib/uncached.c:38:22: warning: symbol 'run_uncached' was not declared. Should it be static?
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Wed, 11 Jul 2007 15:51:00 +0000 (00:51 +0900)]
[MIPS] Cleanup tlbdebug.h
Also include tlbdebug.h in dump_tlb.c and r3k_dump_tlb.c.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Wed, 11 Jul 2007 14:30:40 +0000 (23:30 +0900)]
[MIPS] Change names of local variables to silence sparse (part 2)
This patch is an workaround for these sparse warnings:
include2/asm/mmu_context.h:172:2: warning: symbol 'flags' shadows an earlier one
include2/asm/mmu_context.h:133:16: originally declared here
include2/asm/mmu_context.h:232:2: warning: symbol 'flags' shadows an earlier one
include2/asm/mmu_context.h:203:16: originally declared here
include2/asm/mmu_context.h:277:3: warning: symbol 'flags' shadows an earlier one
include2/asm/mmu_context.h:250:16: originally declared here
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Wed, 11 Jul 2007 14:12:00 +0000 (23:12 +0900)]
[MIPS] Workaround for a sparse warning in include/asm-mips/io.h
CKSEG1ADDR() returns unsigned int value on 32bit kernel. Cast it to
unsigned long to get rid of this warning:
include2/asm/io.h:215:12: warning: cast adds address space to expression (<asn:2>)
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Thomas Bogendoerfer [Wed, 11 Jul 2007 17:10:39 +0000 (19:10 +0200)]
[MIPS] RM: Use only phyiscal address for 82596 and 53c710
Use physical address for 82596 and 53c710 base address
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Thu, 12 Jul 2007 13:01:06 +0000 (14:01 +0100)]
[MIPS] Hydrogen3: Remove remaining bits of code.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 10 Jul 2007 23:20:01 +0000 (00:20 +0100)]
[MIPS] DEC: Fix modpost warning.
LD vmlinux
SYSMAP System.map
SYSMAP .tmp_System.map
MODPOST vmlinux
WARNING: drivers/built-in.o(.data+0x2480): Section mismatch: reference to .init.text: (between 'sercons' and 'ds_parms')
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 10 Jul 2007 23:07:34 +0000 (00:07 +0100)]
Revert "[MIPS] DEC: Fix modpost warning."
This reverts commit
8713762acf341edea9d25d6a4817f235c67bc004.
Ralf Baechle [Wed, 11 Jul 2007 07:32:21 +0000 (08:32 +0100)]
[MIPS] Fix resume for 64K page size on R4000 class processors.
Problem reported by Peter Watkins <pwatkins@sicortex.com> but this is
a different fix.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Catalin Marinas [Wed, 11 Jul 2007 10:29:39 +0000 (11:29 +0100)]
[ARM] 4474/1: Do not check the PSR_F_BIT in valid_user_regs
When running Linux in non-secure mode (on ARM1176 for example),
depending on the CP15 secure configuration register, the CPSR.F bit
(6) might only be modified from the secure mode. However, the
valid_user_regs() function checks for this bit being cleared. With
commit
a6c61e9d, a SIGSEGV is forced in handle_signal() if the user
registers are not considered valid.
The patch also ensures that the CPSR.A bit is cleared and the USR mode
is set if the CPU does not support the 26bit user mode.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Catalin Marinas [Thu, 12 Jul 2007 15:10:22 +0000 (16:10 +0100)]
[ARM] 4473/2: Take the HWCAP definitions out of the elf.h file
The patch moves the HWCAP definitions and the extern elf_hwcap
declaration to the hwcap.h header file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 15 May 2007 14:39:36 +0000 (15:39 +0100)]
[ARM] pxa: move platform devices to separate header file
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 15 May 2007 09:39:49 +0000 (10:39 +0100)]
[ARM] pxa: move device registration into CPU-specific file
This allows individual CPU support to determine which platform
devices should be registered. Also fix a copy-n-paste bug in
the I2C power platform device entry.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 27 Jun 2007 08:57:32 +0000 (09:57 +0100)]
[ARM] pxa: remove boot time RTC initialisation
The RTC library code contains everything necessary to set the
system time from the RTC; for similar reasons as the previous
commit, it's far better to let the RTC library code sort this
out rather than implement something which might not be
appropriate for everyone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 27 Jun 2007 08:56:05 +0000 (09:56 +0100)]
[ARM] pxa: stop doing our own rtc management over suspend
Remove the RTC management over a suspend/resume cycle. Firstly,
we may not be using the internal RTC for time keeping; some
platforms have an external RTC for this inspite of the PXA having
an internal RTC. Secondly, the RTC library code handles updating
system time on resume.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Miao [Fri, 22 Jun 2007 04:40:17 +0000 (05:40 +0100)]
[ARM] 4451/1: pxa: make dma.c generic and remove cpu specific dma code
Since the number of dma channels varies between pxa25x and pxa27x, it
introduces some specific code in dma.c. This patch moves the specific
code to pxa25x.c and pxa27x.c and makes dma.c more generic.
1. add pxa_init_dma() for dma initialization, the number of channels
are passed in by the argument
2. add a "prio" field to the "struct pxa_dma_channel" for the channel
priority, and is initialized in pxa_init_dma()
3. use a general priority comparison with the channels "prio" field so
to remove the processor specific pxa_for_each_dma_prio macro, this
is not lightning fast as the original one, but it is acceptable as
it happens when requesting dma, which is usually not so performance
critical
Signed-off-by: eric miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Miao [Fri, 22 Jun 2007 03:14:09 +0000 (04:14 +0100)]
[ARM] 4450/1: pxa: add pxa25x_init_irq() and pxa27x_init_irq()
/* should be ok this time, I aligned this patch to your arm:pxa2.mbox */
1. move pxa25x specific IRQ initialization code to pxa25x_init_irq()
and pxa27x code to pxa27x_init_irq(), remove pxa_init_irq()
2. replace all pxa_init_irq() with their PXA25x or PXA27x specific
functions
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Miao [Wed, 6 Jun 2007 05:49:59 +0000 (06:49 +0100)]
[ARM] 4440/1: PXA: enable the checking of ICIP2 for IRQs
ICIP2 is not examined during IRQ entrance, this patch add the
checking if the processor is PXA27x or later, with CoreG bits
in CPUID (Core Generation) > 1
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Miao [Wed, 6 Jun 2007 05:45:18 +0000 (06:45 +0100)]
[ARM] 4438/1: PXA: remove #ifdef .. #endif from pxa_gpio_demux_handler()
1. use GPIO_IRQ_mask[] to select those bits of interest, actually
only those "unmasked" GPIO IRQs with their corresponding bits
in GPIO_IRQ_mask[] set to "1" should be checked
2. remove #ifdef PXA_LAST_GPIO > 96 .. #endif, GPIO_IRQ_mask[]
is used to mask out the irrelevant bits, so that even though
the GEDR3 on PXA25x is reserved, it will be masked, and the
following code will never run. Another point is that GPIO85-
GPIO95 bits within GEDR2 will also be masked out on PXA25x
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Miao [Wed, 6 Jun 2007 05:37:15 +0000 (06:37 +0100)]
[ARM] 4437/1: PXA: move the GPIO IRQ initialization code to pxa_init_irq_gpio()
move the GPIO IRQ initialization code to pxa_init_irq_gpio()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Miao [Wed, 6 Jun 2007 05:36:04 +0000 (06:36 +0100)]
[ARM] 4436/1: PXA: move low IRQ initialization code to pxa_init_irq_low()
1. move low IRQ initialization code to pxa_init_irq_low()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
projects / openwrt / staging / blogic.git / log