openwrt/staging/blocktrron.git
20 months agodnsmasq: configure dynamic dhcp6 and dhcp4 independently
Ian Dall [Fri, 10 Mar 2023 06:32:34 +0000 (17:02 +1030)]
dnsmasq: configure dynamic dhcp6 and dhcp4 independently

Given ipv6 has SLAAC it is quite plausible to wish to use dynamic
dhcp4 but static dhcp6. This patch keeps dynamicdhcp as the default
option for both, but is overridden by dynamicdhcpv6 or dynamicdhcpv4

Signed-off-by: Ian Dall <ian@beware.dropbear.id.au>
20 months agoramips: mt7621: add migration script for WLAN PCI paths
Felix Baumann [Sat, 18 Mar 2023 05:55:12 +0000 (06:55 +0100)]
ramips: mt7621: add migration script for WLAN PCI paths

PCI paths of the WLAN devices have changed between kernel 5.10 and 5.15;
migrate config so existing wifi-iface definitions don't break.

This is implemented as a hotplug handler rather than a uci-defaults script
as the migration script must run before the 10-wifi-detect hotplug handler.

based on b452af23a8602ebf7bfb0eb084383ecd595face5

migration was forgotten when device trees were adjusted in
688697889c9ceb9d2d8d413d1abcc5fa7edb402b
c77913be5be5f11a0f20dba1b45b96470099e8a8

fixes #9374

affected devices:
Netgear R6220
Netgear WAC104
Netgear WNDR3700 v5
Zbtlink ZBT-WE1326
Wiflyer WF3526-P
Arcadyan WE420223-99
Beeline Smartbox Flash (Arcadyan WG443223)
MTS WG430223 (Arcadyan WG430223)

Tested-by: Maximilian Baumgartner <aufhaxer@googlemail.com>
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
20 months agodnsmasq: add dhcphostsfile to ujail sandbox
Ruben Jenster [Thu, 23 Mar 2023 10:15:52 +0000 (11:15 +0100)]
dnsmasq: add dhcphostsfile to ujail sandbox

The dhcphostsfile must be mounted into the (ujail) sandbox.
The file can not be accessed without this mount.

Signed-off-by: Ruben Jenster <rjenster@gmail.com>
20 months agoramips: Add support for CJ-Hello HYC-G920
Muhammad AL-Qadhy [Tue, 21 Mar 2023 06:49:22 +0000 (08:49 +0200)]
ramips: Add support for CJ-Hello HYC-G920

Hanyang Digitech Co., Ltd.
MSIP-CMM-HYD-HYC-G920
CJ-Hello HYC-G920

SoC : MediaTek MT7621AT
RAM : 256M (SK hynix H5TQ2G63FFR)
FLASH : 16MB (Winbond W25Q128BV)
WiFi : MediaTek MT7602EN bgn 2SS
WiFi : MediaTek MT7612EN nac 2SS
BTN : Reset
LED : - Power RED
  - WAN Green
  - LAN {1-4}
  - WiFi 2.4 GHz Blue
  - WiFi 5 GHz Blue
  - USB Green

**For MT7621 stage1 DDR Test**

UART : J4 GND - 3V3 - TX - RX - GND / 57600-8N1

```
                MT7621   stage1 code 10:33:55 (ASIC)
                CPU=500000000 HZ BUS=166666666 HZ
```

**For u boot environment**

UART : J4 GND - 3V3 - TX - RX - GND / 115200-8N1

**UART Menu**

```
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
```

**Steps**

Press 4: Entr boot command line interface.

On the pormpt enter.
`setenv firmware_size 0xf60000`
Then enter.
`saveenv`
Then enter.
`reset`

**Device will reboot**

Set your IP 192.168.100.100/24
Connect your lan cable to wan port.

**On the UART Menu**

Press 2: Load system code then write to Flash via TFTP.

 Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) **enter** `Y`
 Please Input new ones /or Ctrl-C to discard
        Input device IP (192.168.100.55) ==:`192.168.100.55`
        Input server IP (192.168.100.100) ==:`192.168.100.100`
        Input Linux Kernel filename () ==:`openwrt-22.03.0-ramips-mt7621-hanyang_hyc-g920-squashfs-sysupgrade.bin`

After uploading firmware image, device will boot Openwrt.

Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
20 months agokernel: modules: tg3: limit to devices with pci support
Aleksander Jan Bajkowski [Fri, 2 Dec 2022 22:38:51 +0000 (23:38 +0100)]
kernel: modules: tg3: limit to devices with pci support

Kmod-tg3 supports Ethernet adapters over PCIe bus. On targets without
PCI support, this package is empty. Symbol CONFIG_TIGON3 depends on
CONFIG_PCI.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
20 months agokernel: modules: hfcpci: limit to devices with pci support
Aleksander Jan Bajkowski [Fri, 2 Dec 2022 22:12:23 +0000 (23:12 +0100)]
kernel: modules: hfcpci: limit to devices with pci support

Kmod-hfcpci and kmod-hfcmulti supports ISDN adapters over PCI. On targets
without PCI support, this package is empty. Symbol CONFIG_MISDN_HFCMULTI
and CONFIG_MISDN_HFCPCI depends on CONFIG_PCI.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
20 months agolibtraceevent: update to 1.7.2
Nick Hainke [Tue, 28 Mar 2023 22:29:47 +0000 (00:29 +0200)]
libtraceevent: update to 1.7.2

Changes:
1c6f0f3 libtraceevent: version 1.7.2
73f6a8a libtraceevent: Fix some missing commas in big endian blocks
da2ea6b libtraceevent: Rename "ok" to "token_has_paren" in process_sizeof()
e6f7cfa libtraceevent: No need for testing ok in else if (!ok) in process_sizeof()
a4b1ba5 libtraceevent: Fix double free in parsing sizeof()

Signed-off-by: Nick Hainke <vincent@systemli.org>
20 months agotools/squashfs4: bump to 4.6.1
Linhui Liu [Fri, 31 Mar 2023 13:42:09 +0000 (21:42 +0800)]
tools/squashfs4: bump to 4.6.1

Changelogs:
https://github.com/plougher/squashfs-tools/blob/4.6.1/CHANGES

Removed upstreamed patches:
- 001-Unsquashfs-Add-and-make-some-header-includes-conditi.patch
- 002-Mksquashfs-Make-sysinfo-conditional.patch
- 003-Only-use-available-CPUs.patch
- 004-action-rework-strdupa-with-POSIX-strdup-and-free.patch
- 005-Don-t-use-sigwaitinfo-sigtimedwait-if-not-supported.patch
- 006-Move-sysinfo.h-into-the-linux-only-section-should-fi.patch
- 007-Unsquashfs-fix-compilation-error-for-missing-sysctl..patch
- 100-portability.patch

Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
20 months agotools/squashfs4: enable parallel builds
Linhui Liu [Fri, 31 Mar 2023 13:34:01 +0000 (21:34 +0800)]
tools/squashfs4: enable parallel builds

Run `time make tools/squashfs4/{clean,compile} -j$(nproc)`
Before:
real    0m8.803s
user    0m12.415s
sys     0m1.317s
After:
real    0m13.781s
user    0m13.290s
sys     0m1.528s

Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
20 months agoramips: mt7621: remove set-affinity script
Rosen Penev [Tue, 28 Mar 2023 22:29:19 +0000 (15:29 -0700)]
ramips: mt7621: remove set-affinity script

From https://github.com/openwrt/openwrt/pull/12280#issuecomment-1489279860
On Ethernet and WLAN, NAPI is threaded for all queues. This means that the
processing work is not stuck on the CPU that fired the IRQ. Under heavy
load, IRQs get disabled anyway, so it should not matter at all which CPUs
the IRQs fire on.

Basic testing indicates this to be true. There's no speedup or slowdown.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
20 months agoramips: mt7621: ASUS RT-AX53U add NMBM, nest firmware
Felix Baumann [Fri, 31 Mar 2023 04:16:04 +0000 (06:16 +0200)]
ramips: mt7621: ASUS RT-AX53U add NMBM, nest firmware

Nests kernel and ubi into firmware partition in-order to be compatible
with OEM firmware. This allows restoring oem firmware from a backup of
firmware2. Add jffs2 partition which is present in the oem firmware.
Add support for mediatek NMBM (wear leveling on newer mediatek devices).
Exclude UBI partition from NMBM management.
Continues PR #10685.

Tested-by: Felix Baumann <felix.bau@gmx.de>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
20 months agokernel: bump 5.15 to 5.15.105
John Audia [Thu, 30 Mar 2023 15:39:17 +0000 (11:39 -0400)]
kernel: bump 5.15 to 5.15.105

Manually rebased:

Removed upstreamed:
backport-5.15/743-v6.3-0005-net-dsa-b53-mmap-fix-device-tree-support.patch[1]
backport-5.15/743-v6.3-0006-net-dsa-tag_brcm-legacy-fix-daisy-chained-switches.patch[2]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.105&id=9bbb3d3f218f1cf51f57a43cf8fd63b05be1b821
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.105&id=48f52431af9980582b6faa32ff8b581edb10486c

Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
20 months agokernel: add support for XMC XM25QH64C
Joe Mullally [Sun, 26 Feb 2023 22:01:22 +0000 (22:01 +0000)]
kernel: add support for XMC XM25QH64C

The XMC XM25QH64C is a 8MB SPI NOR chip. The patch is verified on TL-WPA8631P v3.
Datasheet available at https://www.xmcwh.com/uploads/442/XM25QH64C.pdf

Signed-off-by: Joe Mullally <jwmullally@gmail.com>
20 months agomac80211: ath11k: restore 160MHz support
Robert Marko [Tue, 28 Mar 2023 11:38:57 +0000 (13:38 +0200)]
mac80211: ath11k: restore 160MHz support

Recent ath11k sync introduced a regression causing 80+80 and 160MHz to
stop being advertised and thus not selectable due to the respective feature
flags being cleared.

So, until we get answers upstream to what was the reasoning behind this and
it gets fixed, lets just remove the flag clearing to reanable 160MHz.

Fixes: 789a0bac3535 ("mac80211: ath11k: sync with ath-next")
Signed-off-by: Robert Marko <robimarko@gmail.com>
20 months agobusybox: enable taskset by default
Felix Fietkau [Sat, 1 Apr 2023 07:07:54 +0000 (09:07 +0200)]
busybox: enable taskset by default

This is useful for controlling process affinity on SMP systems

Signed-off-by: Felix Fietkau <nbd@nbd.name>
20 months agokernel: fix mtk_eth_soc flow accounting for MT7986
Felix Fietkau [Sat, 1 Apr 2023 07:07:22 +0000 (09:07 +0200)]
kernel: fix mtk_eth_soc flow accounting for MT7986

This was accidentally dropped when MT7981 support was added

Signed-off-by: Felix Fietkau <nbd@nbd.name>
20 months agoarm-trusted-firmware-sunxi: bump to 2.8
Stijn Tintel [Tue, 20 Dec 2022 18:05:40 +0000 (20:05 +0200)]
arm-trusted-firmware-sunxi: bump to 2.8

Use latest release build instead of a git snapshot. As this tarball
extracts in a trusted-firmware-a-2.8 subdirectory, we no longer need to
override the PKG_NAME defined in trusted-firmware-a.mk. The actual
package name is still the same, so we don't need to update any
dependencies.

Tested on A64-OLinuXino-1Ge16GW.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
20 months agouboot-sunxi: bump to 2020.07
Stijn Tintel [Wed, 21 Dec 2022 20:00:49 +0000 (22:00 +0200)]
uboot-sunxi: bump to 2020.07

This is the newest release where 210-sunxi-deactivate-binman.patch still
applies.

Tested on A64-Olinuxino-eMMC.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
20 months agoipq40xx: add LED functions for Google WiFi
Jan-Niklas Burfeind [Mon, 27 Mar 2023 05:29:39 +0000 (07:29 +0200)]
ipq40xx: add LED functions for Google WiFi

Add LED function properties for the LED controller to avoid failing
driver probe with kernel 5.15.

While at it, also define the OpenWrt LED indicator patterns for this
device.

Ref commit 583ac0e11df7 ("mpc85xx: update lp5521 led-controller node for 5.10")

Google uses white for running and red for an issue

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Tested-by: Andrijan Möcker <amo@ct.de>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
20 months agoipq40xx: add reset button for Google WiFi (Gale)
Jan-Niklas Burfeind [Sun, 26 Mar 2023 20:50:42 +0000 (22:50 +0200)]
ipq40xx: add reset button for Google WiFi (Gale)

Add the external reset button for use with OpenWrt.

Co-authored-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
20 months agobmips: bcm6362/bcm63268: enable HW RNG
Álvaro Fernández Rojas [Fri, 31 Mar 2023 15:49:58 +0000 (17:49 +0200)]
bmips: bcm6362/bcm63268: enable HW RNG

This enables the HW Random Number Generator on the BCM6362 and BCM63268 SoCs,
which is the same one used on BCM6368 SoC.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
20 months agokernel: remove obsolete netfilter tcp window size check bypass patch
Felix Fietkau [Thu, 30 Mar 2023 12:14:11 +0000 (14:14 +0200)]
kernel: remove obsolete netfilter tcp window size check bypass patch

On any currently supported hardware, the performance impact should not
matter anymore.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
20 months agomac80211, mt76: add fixes for recently discovered security issues
Felix Fietkau [Wed, 29 Mar 2023 15:54:19 +0000 (17:54 +0200)]
mac80211, mt76: add fixes for recently discovered security issues

Fixes CVE-2022-47522

Signed-off-by: Felix Fietkau <nbd@nbd.name>
20 months agoramips: Refresh patches
Hauke Mehrtens [Wed, 29 Mar 2023 17:07:05 +0000 (19:07 +0200)]
ramips: Refresh patches

Refresh the ramips kernel patches.

Fixes: 7472476aef26 ("kernel: fix mtk_eth_soc throughput regressions on gigabit PHY ports")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
20 months agobmips: bcm6348-enet: register emac driver from iudma
Álvaro Fernández Rojas [Wed, 29 Mar 2023 16:19:11 +0000 (18:19 +0200)]
bmips: bcm6348-enet: register emac driver from iudma

Register the ethernet driver from iudma, which avoids the attempt to probe the
emac driver before iudma and its consequent deferral.
The ethernet driver can't work without iudma anyway.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
20 months agokernel: filter out pahole version
Robert Marko [Tue, 7 Mar 2023 14:00:28 +0000 (15:00 +0100)]
kernel: filter out pahole version

Pahole version is being autodetected during runtime since kernel 5.15.96
via in-kernel scripts/pahole-version.sh so add CONFIG_PAHOLE_VERSION to
kernel filter in order to prevent it from being added to target configs.

Signed-off-by: Robert Marko <robimarko@gmail.com>
20 months agocomgt: ncm: support Mikrotik R11e-LTE6 modem
Szabolcs Hubai [Fri, 24 Mar 2023 23:00:27 +0000 (00:00 +0100)]
comgt: ncm: support Mikrotik R11e-LTE6 modem

The Mikrotik R11e-LTE6 modem is similar to ZTE MF286R modem, added
earlier: it has a Marvel chip, able to work in ACM+RNDIS mode, knows ZTE
specific commands, runs OpenWrt Barrier Breaker fork.
While the modem is able to offer IPv6 address, the RNDIS setup is unable
to complete if there is an IPv6 adress.

While it works in ACM+RNDIS mode, the user experience isn't as good as
with "proto 3g": the modem happily serves a local IP (192.168.1.xxx)
without internet access. Of course, if the modem has enough time
(for example at the second dialup), it will serve a public IP.

Modifing the DHCP Lease (to a short interval before connect and back to
default while finalizing) is a workaround to get a public IP at the
first try.

A safe workaround for this is to excercise an offline script of the
pingcheck program: simply restart (ifdown - ifup) the connection.

Another pitfall is that the modem writes a few messages at startup,
which confuses the manufacturer detection algorithm and got disabled.

    daemon.notice netifd: Interface 'mikrotik' is setting up now
    daemon.notice netifd: mikrotik (2366): Failed to parse message data
    daemon.notice netifd: mikrotik (2366): WARNING: Variable 'ok' does not exist or is not an array/object
    daemon.notice netifd: mikrotik (2366): Unsupported modem
    daemon.notice netifd: mikrotik (2426): Stopping network mikrotik
    daemon.notice netifd: mikrotik (2426): Failed to parse message data
    daemon.notice netifd: mikrotik (2426): WARNING: Variable '*simdetec:1,sim' does not exist or is not an array/object
    daemon.notice netifd: mikrotik (2426): Unsupported modem
    daemon.notice netifd: Interface 'mikrotik' is now down

A workaround for this is to use the "delay" option in the interface
configuration.

I want to thank Forum members dchard (in topic Adding support for
MikroTik hAP ac3 LTE6 kit (D53GR_5HacD2HnD)) [1]
and mrhaav (in topic OpenWrt X86_64 + Mikrotik R11e-LTE6) [2]
for sharing their experiments and works.
Another information page was found at eko.one.pl [3].

[1]: https://forum.openwrt.org/t/137555
[2]: https://forum.openwrt.org/t/151743
[3]: https://eko.one.pl/?p=modem-r11elte

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
20 months agocomgt: add quirk for Mikrotik modems based on Mikrotik R11e-LTE6
Szabolcs Hubai [Fri, 24 Mar 2023 21:24:26 +0000 (22:24 +0100)]
comgt: add quirk for Mikrotik modems based on Mikrotik R11e-LTE6

The MikroTik R11e-LTE6 modem goes into flight mode (CFUN=4) at startup
and the radio is off (*RADIOPOWER: 0):

    AT+RESET
    OK

    OK

    *SIMDETEC:2,NOS

    *SIMDETEC:1,SIM

    *ICCID: 8936500119010596302

    *EUICC: 1

    +MSTK: 11, D025....74F3

    *ADMINDATA: 0, 2, 0

    +CPIN: READY

    *EUICC: 1

    *ECCLIST: 5, 0, 112, 0, 000, 0, 08, 0, 118, 0, 911

    +CREG: 0

    $CREG: 0

    +CESQ: 99,99,255,255,255,255

    *CESQ: 99,99,255,255,255,255,0

    +CGREG: 0

    +CEREG: 0

    +CESQ: 99,99,255,255,255,255

    *CESQ: 99,99,255,255,255,255,0

    *RADIOPOWER: 0

    +MMSG: 0, 0

    +MMSG: 0, 0

    +MMSG: 1, 0

    +MPBK: 1

While the chat script is able to establish the PPP connection,
it's closed instantly by the modem: LCP terminated by peer.

    local2.info chat[7000]: send (ATD*99***1#^M)
    local2.info chat[7000]: expect (CONNECT)
    local2.info chat[7000]: ^M
    local2.info chat[7000]: ATD*99***1#^M^M
    local2.info chat[7000]: CONNECT
    local2.info chat[7000]:  -- got it
    local2.info chat[7000]: send ( ^M)
    daemon.info pppd[6997]: Serial connection established.
    kern.info kernel: [  453.659146] 3g-mikrotik: renamed from ppp0
    daemon.info pppd[6997]: Renamed interface ppp0 to 3g-mikrotik
    daemon.info pppd[6997]: Using interface 3g-mikrotik
    daemon.notice pppd[6997]: Connect: 3g-mikrotik <--> /dev/ttyACM0
    daemon.info pppd[6997]: LCP terminated by peer
    daemon.notice pppd[6997]: Connection terminated.
    daemon.notice pppd[6997]: Modem hangup
    daemon.info pppd[6997]: Exit.
    daemon.notice netifd: Interface 'mikrotik' is now down

Sending "AT+CFUN=1" to modem deactivates the flight mode and
solves the issue:

    daemon.notice netifd: Interface 'mikrotik' is setting up now
    daemon.notice netifd: mikrotik (7051): sending -> AT+CFUN=1
    daemon.notice pppd[7137]: pppd 2.4.9 started by root, uid 0
    local2.info chat[7140]: abort on (BUSY)
    local2.info chat[7140]: abort on (NO CARRIER)
    local2.info chat[7140]: abort on (ERROR)
    local2.info chat[7140]: report (CONNECT)
    local2.info chat[7140]: timeout set to 10 seconds
    local2.info chat[7140]: send (AT&F^M)
    local2.info chat[7140]: expect (OK)
    local2.info chat[7140]: ^M
    local2.info chat[7140]: +CESQ: 99,99,255,255,255,255^M
    local2.info chat[7140]: ^M
    local2.info chat[7140]: *CESQ: 99,99,255,255,255,255,0^M
    local2.info chat[7140]: AT&F^MAT&F^M^M
    local2.info chat[7140]: OK
    local2.info chat[7140]:  -- got it
    ...
    local2.info chat[7140]: send (ATD*99***1#^M)
    local2.info chat[7140]: expect (CONNECT)
    local2.info chat[7140]: ^M
    local2.info chat[7140]: ATD*99***1#^M^M
    local2.info chat[7140]: CONNECT
    local2.info chat[7140]:  -- got it
    local2.info chat[7140]: send ( ^M)
    daemon.info pppd[7137]: Serial connection established.
    kern.info kernel: [  463.094254] 3g-mikrotik: renamed from ppp0
    daemon.info pppd[7137]: Renamed interface ppp0 to 3g-mikrotik
    daemon.info pppd[7137]: Using interface 3g-mikrotik
    daemon.notice pppd[7137]: Connect: 3g-mikrotik <--> /dev/ttyACM0
    daemon.warn pppd[7137]: Could not determine remote IP address: defaulting to 10.64.64.64
    daemon.notice pppd[7137]: local  IP address 100.112.63.62
    daemon.notice pppd[7137]: remote IP address 10.64.64.64
    daemon.notice pppd[7137]: primary   DNS address 185.29.83.64
    daemon.notice pppd[7137]: secondary DNS address 185.62.131.64
    daemon.notice netifd: Network device '3g-mikrotik' link is up
    daemon.notice netifd: Interface 'mikrotik' is now up

To send this AT command to the modem the "runcommand.gcom" script
dependency is moved from comgt-ncm to comgt.
As the comgt-ncm package depends on comgt already, this change
is a NOOP from that point of view.
But from the modem's point it is a low hanging fruit as the modem
is usable with installing comgt and kmod-usb-ncm packages.

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
20 months agomediatek: re-add wireless driver for TUF-AX4200
Andrew Sim [Wed, 29 Mar 2023 07:48:30 +0000 (09:48 +0200)]
mediatek: re-add wireless driver for TUF-AX4200

The wireless driver package was incorrectly removed from the TUF-AX4200
device-packages, resulting in images without wireless functionality.

Fixes: d98c4fb8bfab ("mediatek: broaden filogic target description")
Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
[rework commit description]
Signed-off-by: David Bauer <mail@david-bauer.net>
20 months agobmips: bcm6348-enet: add PHY support
Álvaro Fernández Rojas [Wed, 29 Mar 2023 14:17:04 +0000 (16:17 +0200)]
bmips: bcm6348-enet: add PHY support

We should ensure that the PHY is properly configured.
This is specially needed in devices using the internal PHY for ethernet0.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
20 months agokernel: fix mtk_eth_soc throughput regressions on gigabit PHY ports
Felix Fietkau [Wed, 29 Mar 2023 09:38:30 +0000 (11:38 +0200)]
kernel: fix mtk_eth_soc throughput regressions on gigabit PHY ports

Fixes issues on MT7621 and MT7623 switch ports, and PHY ports on all SoC

Signed-off-by: Felix Fietkau <nbd@nbd.name>
20 months agobmips: add basic BCM6358 ethernet support
Álvaro Fernández Rojas [Tue, 24 May 2022 09:14:21 +0000 (11:14 +0200)]
bmips: add basic BCM6358 ethernet support

The MDIO bus is supported but there are errors when trying to probe and
configure the external BCM5325E switch through B53 DSA.
Therefore, let's add basic ethernet (but working) support for now.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
20 months agobmips: bcm6368-enetsw: refactor probe
Álvaro Fernández Rojas [Tue, 28 Mar 2023 17:36:59 +0000 (19:36 +0200)]
bmips: bcm6368-enetsw: refactor probe

- Switch to devm functions where possible.
- Fix probing when no resets provided.
- Properly check pointers (IS_ERR_OR_NULL/PTR_ERR).
- Add probe info.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
20 months agobmips: bcm6368-enetsw: remove unneeded variables
Álvaro Fernández Rojas [Tue, 28 Mar 2023 16:47:17 +0000 (18:47 +0200)]
bmips: bcm6368-enetsw: remove unneeded variables

Change the code to use defines instead of variables.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
20 months agobmips: bcm6368-enetsw: harmonize dev variables
Álvaro Fernández Rojas [Tue, 28 Mar 2023 16:34:46 +0000 (18:34 +0200)]
bmips: bcm6368-enetsw: harmonize dev variables

The current implementation of bcm6368-enetsw is a mess of dev, ndev and kdev
variables, which have refer to different things depending on the function.
This commit harmonizes it and resolves the issue.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
20 months agobmips: sercomm,h500-s: add Quantenna gpio switch
Álvaro Fernández Rojas [Sun, 26 Mar 2023 12:38:41 +0000 (14:38 +0200)]
bmips: sercomm,h500-s: add Quantenna gpio switch

Sercomm H500-s has a Quantenna SoC for external wifi which can be activated or
deactivated through GPIO #20.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
20 months agoncm: add error check and retry mechanism for gcom call
Mike Wilson [Mon, 20 Jul 2020 20:25:33 +0000 (22:25 +0200)]
ncm: add error check and retry mechanism for gcom call

This patch solves the problem of receiving "error" responses when
initially calling gcom. This avoids unnecessary NO_DEVICE failures.

A retry loop retries the call after an "error" response within the
specified delay. A successful response will continue with the connection
immediately without waiting for max specified delay, bringing the
interface up sooner.

Signed-off-by: Mike Wilson <mikewse@hotmail.com>
20 months agokernel: remove unnecessary change from backlog threading fix
Felix Fietkau [Tue, 28 Mar 2023 11:13:53 +0000 (13:13 +0200)]
kernel: remove unnecessary change from backlog threading fix

Fixes: f1c9bd6f6f41 ("kernel: fix kernel warning and network issue in the backlog threading patch")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
20 months agokernel: fix kernel warning and network issue in the backlog threading patch
Felix Fietkau [Tue, 28 Mar 2023 10:46:11 +0000 (12:46 +0200)]
kernel: fix kernel warning and network issue in the backlog threading patch

Fixes enabling it early during the boot

Signed-off-by: Felix Fietkau <nbd@nbd.name>
20 months agomediatek: broaden filogic target description
Daniel Golle [Fri, 10 Mar 2023 20:05:18 +0000 (20:05 +0000)]
mediatek: broaden filogic target description

The filogic subtarget now also supports MT7981 and will in future
also support MT7988. Reflect that in the target description.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agomediatek: add device tree include for the MT7981 SoC
Daniel Golle [Sat, 11 Mar 2023 03:55:52 +0000 (03:55 +0000)]
mediatek: add device tree include for the MT7981 SoC

Add mt7981.dtsi so we can start adding MT7981 devices.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agogeneric: fix Macronix SPI-NAND driver
Daniel Golle [Sat, 11 Mar 2023 02:38:59 +0000 (02:38 +0000)]
generic: fix Macronix SPI-NAND driver

Use scratch buffer for DMA operetations. Passing a pointer to a stack
variable won't work and results in bogus bit flips being reported.

Patch was submitted upstream and is part of Linux 6.3.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agomediatek: add support for SPI calibration
Daniel Golle [Fri, 10 Mar 2023 23:53:54 +0000 (23:53 +0000)]
mediatek: add support for SPI calibration

Newer MediaTek's SoCs need SPI calibration routines for SPI to work
reliably. Import patches for that from MediaTek's SDK.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agomediatek: add PWM support for MT7981 SoC
Daniel Golle [Fri, 10 Mar 2023 19:57:18 +0000 (19:57 +0000)]
mediatek: add PWM support for MT7981 SoC

Add patch to support PWM on the MT7981 SoC.
This patch will also be submitted to upstream Linux soon.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agomediatek: add I2C for MT7981 SoC
Daniel Golle [Fri, 10 Mar 2023 19:55:09 +0000 (19:55 +0000)]
mediatek: add I2C for MT7981 SoC

Add patch to support I2C on the MT7981 SoC.
This change will also be submitted to upstream Linux soon.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agomediatek: simplify MaxLinear GPY PHY driver
Daniel Golle [Sat, 11 Mar 2023 03:51:00 +0000 (03:51 +0000)]
mediatek: simplify MaxLinear GPY PHY driver

The mxl-gpy driver apparently was built in the assumption that SGMII
auto-negotiation is always switched on at the MAC. This may be true for
few rather recent drivers (why?), but certainly isn't for most drivers
unless 'managed = "in-band-status"' is set in device tree. Add patch to
the mediatek target which reduces mxl-gpy to behave more like an
ordinary PHY driver using out-of-band status.

This allows to use these PHYs without rate-adaptation which seems to be
at least partially broken/racy in some revisions of the PHY and/or
internal PHY firmware.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agogeneric: dsa: make use of pcs-mtk-lynxi also for mt7530
Daniel Golle [Sat, 11 Mar 2023 17:58:12 +0000 (17:58 +0000)]
generic: dsa: make use of pcs-mtk-lynxi also for mt7530

The MT7531 switch IC comes with SerDes ports with PCS identical to
what is also used in MediaTek's SoCs. Make use of the shared driver
to ease maintainance and reduce code duplication.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agogeneric: backport regmap reg_base and downshift features
Daniel Golle [Sat, 11 Mar 2023 17:55:56 +0000 (17:55 +0000)]
generic: backport regmap reg_base and downshift features

Backport new regmap features from Linux 5.18 which are needed to let
mt7530 use pcs-mtk-lynxi.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agogeneric: mtk_eth_soc: switch to external PCS driver
Daniel Golle [Mon, 27 Mar 2023 17:15:13 +0000 (18:15 +0100)]
generic: mtk_eth_soc: switch to external PCS driver

Backport patch to make use of the new PCS driver in mtk_eth_soc.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agogeneric: pcs-mtk-lynxi: add hack to use 2500Base-X without AN
Daniel Golle [Mon, 27 Mar 2023 17:41:54 +0000 (18:41 +0100)]
generic: pcs-mtk-lynxi: add hack to use 2500Base-X without AN

Using 2500Base-T SFP modules e.g. on the BananaPi R3 requires manually
disabling auto-negotiation, e.g. using ethtool. While a proper fix
using SFP quirks is being discussed upstream, bring a work-around to
restore user experience to what it was before the switch to the
dedicated SGMII PCS driver.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agogeneric: net: pcs: add driver for MediaTek SGMII PCS
Daniel Golle [Mon, 27 Mar 2023 17:14:21 +0000 (18:14 +0100)]
generic: net: pcs: add driver for MediaTek SGMII PCS

Backport dedicated PCS driver for MediaTek LynxI SGMII/SerDes unit.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agogeneric: mtk_eth_soc: allow setting MDIO clock frequency
Daniel Golle [Mon, 27 Mar 2023 16:50:54 +0000 (17:50 +0100)]
generic: mtk_eth_soc: allow setting MDIO clock frequency

Backport patch allowing to set the MDIO bus clock frequency.
By default the MDIO bus clock runs on 2.5 MHz, allow increasing it
up to 25 MHz.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agomediatek: add support for built-in GE PHYs of newer SoCs
Daniel Golle [Fri, 10 Mar 2023 19:44:52 +0000 (19:44 +0000)]
mediatek: add support for built-in GE PHYs of newer SoCs

MT7981 and the upcoming MT7988 have built-in Gigabit Ethernet PHYs.
While they share some design properties with the PHYs present in
MT753x, they do need calibration data from the SoC's efuse.

Add driver to support them. Upstreaming it is planned, but there are
still some ongoing discussions with MediaTek.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agogeneric: backport support for MT7981 Ethernet
Daniel Golle [Fri, 10 Mar 2023 19:41:51 +0000 (19:41 +0000)]
generic: backport support for MT7981 Ethernet

Backport support for the MT7981 SoC to mtk_eth_soc.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agomediatek: backport pinctrl driver for MT7981 SoC
Daniel Golle [Fri, 10 Mar 2023 19:40:37 +0000 (19:40 +0000)]
mediatek: backport pinctrl driver for MT7981 SoC

Backport the pinctrl driver for the MT7981 SoC. The driver has also
been submitted upstream and is part of Linux 6.3.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agomediatek: backport clk driver for MT7981 SoC
Daniel Golle [Fri, 10 Mar 2023 19:36:12 +0000 (19:36 +0000)]
mediatek: backport clk driver for MT7981 SoC

Backport driver for common clocks in MT7981 SoC. The driver has also
been submitted upstream and became part of Linux 6.3.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agogeneric: replace mtk_sgmii patches with versions accepted upstream
Daniel Golle [Mon, 27 Mar 2023 15:02:44 +0000 (16:02 +0100)]
generic: replace mtk_sgmii patches with versions accepted upstream

Replace patches for MediaTek Ethernet driver SGMII/SerDes unit with
their corresponding upstream patches. Not all of the patches in our
tree went upstream as-is, some are slightly different implementations,
and they require the phylink_pcs helpers now made available.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agogeneric: backport some phylink helper functions
Daniel Golle [Sat, 11 Mar 2023 03:44:41 +0000 (03:44 +0000)]
generic: backport some phylink helper functions

It isn't feasible to literally backport all upstream phylink_pcs changes
down to Linux 5.15: It's just too many patches, and many downstream
drivers and hacks are likely to break. We are too close to branching off
to risk this, and it's also just too much work.
Instead just add helper functions used by modern PCS drivers while keeping
the original functions instact as well. While this may add a kilobyte or
two of extra kernel size, it has the advantage that we get the best of both
worlds: None of the existing codepaths are touched, but yet we have the
option to backport singular improvements to Ethernet drivers where needed.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20 months agoipq-wifi: bump to latest git HEAD
Christian Marangi [Mon, 27 Mar 2023 16:15:13 +0000 (18:15 +0200)]
ipq-wifi: bump to latest git HEAD

ccd7e46 ipq40xx: add support for Wallystech DR40x9
2ce60e1 Revert "ipq40xx: add support for Wallystech DR40x9"
ea962ca ipq40xx: add Emplus WAP551 BDF

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
20 months agogeneric: 5.15: refresh kernel patches
Christian Marangi [Sat, 25 Mar 2023 16:24:27 +0000 (17:24 +0100)]
generic: 5.15: refresh kernel patches

Refresh kernel patches for generic kernel 5.15 due to new backport
version of MGLRU patchset.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
20 months agokernel: Update MGLRU patchset
Kazuki H [Mon, 20 Mar 2023 21:51:03 +0000 (06:51 +0900)]
kernel: Update MGLRU patchset

The current patches are old, update them from mainline.
Backports taken from https://github.com/yuzhaogoogle/linux/commits/mglru-5.15

Tested-by: Kazuki H <kazukih0205@gmail.com> #mt7622/Linksys E8450 UBI
Signed-off-by: Kazuki H <kazukih0205@gmail.com>
20 months agoramips: add support for Keenetic Lite III rev. A
Alexey Bartenev [Fri, 10 Mar 2023 15:35:30 +0000 (10:35 -0500)]
ramips: add support for Keenetic Lite III rev. A

General specification:
SoC Type: MediaTek MT7620N (580MHz)
ROM: 8 MB SPI-NOR (W25Q64FV)
RAM: 64 MB DDR (EM6AB160TSD-5G)
Switch: MediaTek MT7530
Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
Wireless: 2.4 GHz (MediaTek RT5390): b/g/n
Buttons: 3 button (POWER, RESET, WPS)
Slide switch: 4 position (BASE, ADAPTER, BOOSTER, ACCESS POINT)
Bootloader: U-Boot 1.1.3
Power: 9 VDC, 0.6 A

MAC in stock:
|- + |
| LAN  | RF-EEPROM + 0x04 |
| WLAN | RF-EEPROM + 0x04 |
| WAN  | RF-EEPROM + 0x28 |

OEM easy installation
1. Use a PC to browse to http://my.keenetic.net.
2. Go to the System section and open the Files tab.
3. Under the Files tab, there will be a list of system
files. Click on the Firmware file.
4. When a modal window appears, click on the Choose File
button and upload the firmware image.
5. Wait for the router to flash and reboot.

OEM installation using the TFTP method
1. Download the latest firmware image and rename it to
klite3_recovery.bin.
2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the
firmware image to the root directory of the server.
3. Power off the router and use a twisted pair cable to connect
the PC to any of the router's LAN ports.
4. Configure the network adapter of the PC to use IP address
192.168.1.2 and subnet mask 255.255.255.0.
5. Power up the router while holding the reset button pressed.
6. Wait approximately for 5 seconds and then release the
reset button.
7. The router should download the firmware via TFTP and
complete flashing in a few minutes.
After flashing is complete, use the PC to browse to
http://192.168.1.1 or ssh to proceed with the configuration.

Signed-off-by: Alexey Bartenev <41exey@proton.me>
20 months agobcm47xx: enable adm6996 only on legacy subtarget
Aleksander Jan Bajkowski [Sat, 17 Dec 2022 23:26:19 +0000 (00:26 +0100)]
bcm47xx: enable adm6996 only on legacy subtarget

The generic subtarget supports only a few devices. None of
these devices are equipped with a ADM6996 switch. On the
mips74k subtarget, the driver for the adm6996 switch is
disabled. So it seems that the ADM6996 driver should
be enabled only on the legacy subtarget.

Support for ADM6996 switches was enabled in commit 68081fc1c8c7814b1c064431eb2e364f9226801a.
At the time when this driver was enabled the bcm47xx
target had only one subtarget.

Switches used by individual devices suported by the generic
subtarget are listed below.

Device Switch
Edimax PS-1208MFG int. SoC
Linksys WRT300N v1.1 Broadcom BCM5325
Linksys WRT310N v1 Broadcom BCM5397
Linksys WRT350N v1 Broadcom BCM5397
Linksys WRT610N v1 Broadcom BCM53115
Linksys WRT610N v2 Broadcom BCM53115
Linksys E3000 v1 Broadcom BCM53115

Reduce uncompressed kernel size by 8320 Bytes.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
20 months agobcm47xx: refresh config
Aleksander Jan Bajkowski [Sat, 11 Mar 2023 11:43:34 +0000 (12:43 +0100)]
bcm47xx: refresh config

This was done by executing these command:
$ make kernel_oldconfig CONFIG_TARGET=subtarget

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
20 months agorules.mk: add FILECMD variable
Michael Pratt [Tue, 14 Mar 2023 09:10:50 +0000 (05:10 -0400)]
rules.mk: add FILECMD variable

Some packages using Libtool have the possibility
of using this environment variable if set,
instead of the direct command for "file" using PATH,
or the need to patch a hard-coded path.

This is a new feature of Libtool 2.4.7

Ref: bf261073d ("tools/libtool: bump to 2.4.7")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
20 months agotools/libtool: clean up build recipes
Michael Pratt [Wed, 15 Mar 2023 05:45:02 +0000 (01:45 -0400)]
tools/libtool: clean up build recipes

Host/Clean/Default is no longer defined.

Use the uninstall makefile target
to remove the obsolete m4 files, and more.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
20 months agoautotools: remove specialized version of libtool
Michael Pratt [Thu, 16 Mar 2023 01:22:37 +0000 (21:22 -0400)]
autotools: remove specialized version of libtool

Remove the specialized copy of libtool
which was used for linking to uClibc++, which is now removed.

Also remove references to the deprecated fixup targets
that invoked this specialized libtool, which no package uses.

Ref: 6b2ed6101 ("uclibc++: remove")
Ref: c10515db6 ("re-enable the libtool PKG_BUILD_DEPENDS for PKG_FIXUP")
Ref: 246a5b334 ("More libtool madness")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
20 months agotools/automake: verbose variable compatibility
Michael Pratt [Tue, 14 Mar 2023 09:03:24 +0000 (05:03 -0400)]
tools/automake: verbose variable compatibility

An old patch attempted to harmonize the way that
both Openwrt and Automake uses the $(V) variable.
However, it was reverted because of the side-effects.

This method is more simple and just
allows Automake to accept any string
as part of the verbosity toggle,
falling back to the default if null.

Ref: e6901bf90 ("tools/automake: Revert "Do not use $(V) - force AM_V=1"")
Ref: 43365ca66 ("Do not use $(V) - force AM_V=1")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
20 months agolantiq: xway: add support for AVM FRITZ!Box 7330
Aleksander Jan Bajkowski [Mon, 1 Nov 2021 21:52:21 +0000 (22:52 +0100)]
lantiq: xway: add support for AVM FRITZ!Box 7330

The AVM FRITZ!Box 7330 shares hardware with the AVM Fritzbox 7320
except for the second ethernet port, which only supports 100M.

Hardware:
- SoC: Lantiq ARX 188
- CPU: 2x MIPS 34Kc 393 MHz
- RAM: 64 MiB 196 MHz
- Flash: 16 MiB NAND
- Ethernet: Built-in Gigabit Ethernet switch, 1x 1GbE, 1x 100M
- Wifi: Atheros AR9227-BC2A b/g/n with 2 pcb/internal antennas
- USB: 2x USB 2.0
- DSL: Built-in ADSL2+ modem
- DECT: Dialog SC14441
- LEDs: 1 two-color, 4 one-color
- Buttons: 1x DECT, 1x WIFI
- Telephone connectors: 1 FXS port via TAE or RJ11 connector

Installation:
The installation process is described on the wiki.

Unsupported (same as AVM 7320):
- VoIP (DECT and FXS),
- Second Ethernet port.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
20 months agoath79: Add Aruba AP-175 support
Martin Kennedy [Sun, 18 Sep 2022 16:15:57 +0000 (12:15 -0400)]
ath79: Add Aruba AP-175 support

This board is very similar to the Aruba AP-105, but is
outdoor-first. It is very similar to the MSR2000 (though certain
MSR2000 models have a different PHY[^1]).

A U-Boot replacement is required to install OpenWrt on these
devices[^2].

Specifications
--------------
* Device: Aruba AP-175
* SoC: Atheros AR7161 680 MHz MIPS
* RAM: 128MB - 2x Mira P3S12D40ETP
* Flash: 16MB MXIC MX25L12845EMI-10G (SPI-NOR)
* WiFi: 2 x DNMA-H92 Atheros AR9220-AC1A 802.11abgn
* ETH: IC+ IP1001 Gigabit + PoE PHY
* LED: 2x int., plus 12 ext. on TCA6416 GPIO expander
* Console: CP210X linking USB-A Port to CPU console @ 115200
* RTC: DS1374C, with internal battery
* Temp: LM75 temperature sensor

Factory installation:

- Needs a u-boot replacement. The process is almost identical to that
  of the AP105, except that the case is easier to open, and that you
  need to compile u-boot from a slightly different branch:
  https://github.com/Hurricos/u-boot-ap105/tree/ap175

  The instructions for performing an in-circuit reflash with an
  SPI-Flasher like a CH314A can be found on the OpenWrt Wiki
  (https://openwrt.org/toh/aruba/ap-105); in addition a detailed guide
  may be found on YouTube[^3].

- Once u-boot has been replaced, a USB-A-to-A cable may be used to
  connect your PC to the CP210X inside the AP at 115200 baud; at this
  point, the normal u-boot serial flashing procedure will work (set up
  networking; tftpboot and boot an OpenWrt initramfs; sysupgrade to
  OpenWrt proper.)

- There is no built-in functionality to revert back to stock firmware,
  because the AP-175 has been declared by the vendor[^4] end-of-life
  as of 31 Jul 2020. If for some reason you wish to return to stock
  firmware, take a backup of the 16MiB flash before flashing u-boot.

[^1]: https://github.com/shalzz/aruba-ap-310/blob/master/platform/bootloader/apboot-11n/include/configs/msr2k.h#L186

[^2]: https://github.com/Hurricos/u-boot-ap105/tree/ap175

[^3]: https://www.youtube.com/watch?v=Vof__dPiprs

[^4]: https://www.arubanetworks.com/support-services/end-of-life/#product=access-points&version=0

Signed-off-by: Martin Kennedy <hurricos@gmail.com>
20 months agoramips: mt7621: enable unused PCIe port to fix potential boot failure
Shiji Yang [Tue, 21 Mar 2023 08:50:56 +0000 (16:50 +0800)]
ramips: mt7621: enable unused PCIe port to fix potential boot failure

One user reported that his SIMAX1800T couldn't boot like the others. After
debugging, I found that this was caused by the disabled PCIe port. I cannot
reproduce this issue on my SIMAX1800T. But when I disabled pcie2 on the
ASUS RT-AC57U, I got the same result.

It seems that disabling these unused PCIe ports on some mt7621 revisions
will cause PCIe to fail to initialize. So we'd better to re-enable them on
all related mt7621 devices.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
20 months agoramips: fix 5g mac for TOTOLINK X5000R
Chuanhong Guo [Sun, 26 Mar 2023 15:50:43 +0000 (23:50 +0800)]
ramips: fix 5g mac for TOTOLINK X5000R

There's no valid mac address for the second band in the eeprom.
The vendor fw uses 2.4G mac + 4 as the mac for 5G radio.
Do the same in our firmware.

Fixes: 23be410b3d ("ramips: add support for TOTOLINK X5000R")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
20 months agomac80211: fix receiving mesh packets in forwarding=0 networks
Felix Fietkau [Sun, 26 Mar 2023 15:19:03 +0000 (17:19 +0200)]
mac80211: fix receiving mesh packets in forwarding=0 networks

When forwarding is set to 0, frames are typically sent with ttl=1.
Move the ttl decrement check below the check for local receive in order to
fix packet drops.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
20 months agoath79: calibrate dlink dir-825 b1 with nvmem
Edward Chow [Sun, 20 Nov 2022 05:49:45 +0000 (13:49 +0800)]
ath79: calibrate dlink dir-825 b1 with nvmem

Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.

This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.

Currently, only ethernet devices uses the mac address of
"mac-address-ascii" cells, while PCI ath9k devices uses the mac address
within calibration data.

Signed-off-by: Edward Chow <equu@openmail.cc>
(restored switch configuration in 02_network, integrated caldata into
partition)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
20 months agolantiq: xrx200: convert FritzBox 7360v2's wifi to nvmem
Christian Lamparter [Mon, 13 Mar 2023 21:49:50 +0000 (22:49 +0100)]
lantiq: xrx200: convert FritzBox 7360v2's wifi to nvmem

this was thoroughly tested (warm and cold boots). on a
real 7360v2. This is because there have been documented
hick-ups with other lantiq devices that need the
owl-loader too.

It's likely that the 7360(sl) could be converted in the
same way as well. However the 7362sl uses a reversed
caldata format, so the "qca,no-eeprom" stays in place.

The patch also moves the urloader nvmem partition
definition into the partition section.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
20 months agoapm821xx: Migrate to libdeflate
Christian Lamparter [Mon, 2 Jan 2023 10:04:11 +0000 (11:04 +0100)]
apm821xx: Migrate to libdeflate

libdeflate's gzip compressor provides a better
compression ratio and uboot's decompressor has
no problem with the data streams.

Tested on MX60, WNDR4700, WNDAP660

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
20 months agoipq40xx: Fix Linksys upgrade, restore config step
Jeff Kletsky [Wed, 4 Jan 2023 07:17:03 +0000 (23:17 -0800)]
ipq40xx: Fix Linksys upgrade, restore config step

It appears that the refactor of the upgrade process for NAND devices
resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration
was not preserved over sysupgrade steps.

This was restored for some devices in
commit 84ff6c90dda1 ("base-files: bring back nand_do_upgrade_success").
This restored preservation of config for ipq40xx devices using the
linksys.sh script. Other devices and targets have not been examined.

Closes: #11677
Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code")
Tested-on: EA8300

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
(checkpatch nitpick)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
20 months agoutil-linux: add rev utility package
Oskari Rauta [Sun, 19 Mar 2023 17:39:25 +0000 (19:39 +0200)]
util-linux: add rev utility package

I found use for this in my scripts; I noticed that it is already
compiled with util-linux - there just isn't package for it -
let's package it then.

Description:
The rev utility copies the specified files to the standard output,
reversing the order of characters in everyline.

Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
20 months agokernel: bump 5.10 to 5.10.176
John Audia [Wed, 22 Mar 2023 16:07:50 +0000 (12:07 -0400)]
kernel: bump 5.10 to 5.10.176

All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
20 months agokernel: bump 5.15 to 5.15.104
John Audia [Wed, 22 Mar 2023 15:08:27 +0000 (11:08 -0400)]
kernel: bump 5.15 to 5.15.104

All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
20 months agokernel: bump 5.15 to 5.15.103
John Audia [Sat, 18 Mar 2023 16:46:48 +0000 (12:46 -0400)]
kernel: bump 5.15 to 5.15.103

Manually rebased:
        backport-5.15/704-15-v5.19-net-mtk_eth_soc-move-MAC_MCR-setting-to-mac_finish.patch

Removed upstreamed:
        backport-5.15/060-v6.0-01-tools-build-Add-feature-test-for-init_disassemble_in.patch[1]
        backport-5.15/060-v6.0-02-tools-include-add-dis-asm-compat.h-to-handle-version.patch[2]
        backport-5.15/060-v6.0-03-tools-perf-Fix-compilation-error-with-new-binutils.patch[3]
        backport-5.15/060-v6.0-04-tools-bpf_jit_disasm-Fix-compilation-error-with-new-.patch[4]
        backport-5.15/060-v6.0-05-tools-bpftool-Fix-compilation-error-with-new-binutil.patch[5]
        pending-5.15/733-02-net-ethernet-mtk_eth_soc-fix-RX-data-corruption-issu.patch[6]
        bcm47xx/patches-5.15/170-bgmac-fix-initial-chip-reset-to-support-BCM5358.patch[7]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=51b99dc38c1a053e2e732d7f9e2740e343ae7eae
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=451c9d7b16169645ed291ebb2ca9844caa088f2d
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=97f005c0bdbaf656a7808586d234965385a06c58
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=1c27fab243333821375e4d63128d60093fdbe149
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=4441a90091931fd81607567961dc122f24f735bb
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=2adc29350a5b4669544566f71f208d2abaec60ab
7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=04bfc5bcdfc0fdb73587487c71b04d63807ae15a

Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
20 months agokernel: fix mtk flow offload list corruption issue with l2 flows
Felix Fietkau [Sat, 25 Mar 2023 10:58:19 +0000 (11:58 +0100)]
kernel: fix mtk flow offload list corruption issue with l2 flows

The same node was accidentally used for two different lists, causing an
invalid pointer chain.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
20 months agokernel: refresh mxl-gpy LED patch
Álvaro Fernández Rojas [Sat, 25 Mar 2023 09:35:19 +0000 (10:35 +0100)]
kernel: refresh mxl-gpy LED patch

Make the patches apply cleanly again.

Fixes: 90691f450543 ("generic: mxl-gpy: allow configuring LED registers")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
20 months agokernel: backport dsa b53 patches
Álvaro Fernández Rojas [Sat, 25 Mar 2023 09:33:06 +0000 (10:33 +0100)]
kernel: backport dsa b53 patches

These patches have been merged upstream, so let's move them to backport.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
20 months agobmips: sercomm,h500-s: fix upgrade
Álvaro Fernández Rojas [Sat, 25 Mar 2023 09:23:32 +0000 (10:23 +0100)]
bmips: sercomm,h500-s: fix upgrade

Sercomm H500-s devices don't need the JFFS2 cleanmarkers as opposed to the
other bmips NAND devices.

Fixes: 6df12200d903 ("bmips: add support for Sercomm H-500s")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
21 months agofilogic: add support for ASUS TUF-AX4200 tufax4200
David Bauer [Thu, 26 Jan 2023 16:39:43 +0000 (17:39 +0100)]
filogic: add support for ASUS TUF-AX4200

Hardware
--------
SOC:   MediaTek MT7986
RAM:   512MB DDR3
FLASH: 256MB SPI-NAND (Winbond W25N02KV)
WIFI:  Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH:   MediaTek MT7531 Switch
       MaxLinear GPY211C 2.5 N-Base-T PHY
UART:  3V3 115200 8N1 (Pinout silkscreened / Do not ocnnect VCC)

Installation
------------

1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
   reachable at 192.168.1.66/24. Rename the image to tufax4200.bin.

2. Connect the TFTP server to the AX4200. Conect to the serial console,
   interrupt the autoboot process by pressing '4' when prompted.

3. Download & Boot the OpenWrt initramfs image.

   $ setenv ipaddr 192.168.1.1
   $ setenv serverip 192.168.1.66
   $ tftpboot 0x46000000 tufax4200.bin
   $ bootm 0x46000000

4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
   using scp and install using sysupgrade.

   $ sysupgrade -n <path-to-sysupgrade.bin>

Missing features
----------------

 - The LAN port LEDs are driven by the switch but OpenWrt does not
   correctly configure the output.

Signed-off-by: David Bauer <mail@david-bauer.net>
21 months agomediatek: enable bootargs-override for filogic subtarget
David Bauer [Mon, 13 Mar 2023 02:14:42 +0000 (03:14 +0100)]
mediatek: enable bootargs-override for filogic subtarget

The ASUS TUF-AX4200 bootloader adds invalid parameters for the rootfs.
Without overwriting the cmdline, the kernel crashes when trying to
attach the rootfs, as OpenWrt uses a different partition than the vendor
OS.

Signed-off-by: David Bauer <mail@david-bauer.net>
21 months agogeneric: mxl-gpy: allow configuring LED registers
David Bauer [Sat, 11 Mar 2023 00:38:19 +0000 (01:38 +0100)]
generic: mxl-gpy: allow configuring LED registers

Add a patch to allow modification of the PHY LED configuration. This is
required for boards, where the reset configuration of LED functions is
incompatibe with the usage of the device LEDs.

This is the case for the ASUS TUF-AX4200 Wireless router. It requires
modification of the LED configuration because as the WAN LED on the
front of the device is driven by the PHY. Without patching, it would
only illuminate in case the Link speed is 100 Mbit/s.

Signed-off-by: David Bauer <mail@david-bauer.net>
21 months agogeneric: backport Winbond W25N02KV SPI-NAND support
David Bauer [Fri, 10 Mar 2023 01:19:37 +0000 (02:19 +0100)]
generic: backport Winbond W25N02KV SPI-NAND support

This flash-chip is used on the Asus TUF-AX4200 and TUF-AX6000 routers.

As the filogic target only uses kernel 5.15, skip the 5.10 backport.

Signed-off-by: David Bauer <mail@david-bauer.net>
21 months agokernel: add support for threaded network backlog processing
Felix Fietkau [Sun, 19 Feb 2023 14:01:43 +0000 (15:01 +0100)]
kernel: add support for threaded network backlog processing

This can improve load balancing by pushing backlog (and RPS) processing
to separate threads, allowing the scheduler to distribute the load.
It can be enabled with: echo 1 > /proc/sys/net/core/backlog_threaded

Signed-off-by: Felix Fietkau <nbd@nbd.name>
21 months agoramips: add support for Mercusys MR70X
David Bauer [Thu, 23 Mar 2023 22:53:47 +0000 (23:53 +0100)]
ramips: add support for Mercusys MR70X

Hardware
========
- SoC: MediaTek MT7621AT (880MHz, Duel-Core)
- RAM: DDR3 128MB
- Flash: Winbond W25Q128JV (SPI-NOR 16MB)
- WiFi: MediaTek MT7915D (2.4GHz, 5GHz, DBDC)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x3, SoC)
- UART: >TX RX GND 3v3 (115200 8N1, J1)
        Do not connect 3v3. TX is marked with an arrow.

Installation
============
Flash factory image. This can be done using stock web ui.

Revert to stock firmware
========================
Flash stock firmware via OEM Web UI Recovery mode.

Web UI Recovery method
======================
1. Unplug the router
2. Plug in and hold reset button 5~10 secs
3. Set your computer IP address manually to 192.168.1.x / 255.255.255.0
4. Flash image with web browser to 192.168.1.1

Co-authored-by: Robert Senderek <robert.senderek@10g.pl>
Co-authored-by: Yoonji Park <koreapyj@dcmys.kr>
Signed-off-by: David Bauer <mail@david-bauer.net>
21 months agomac80211: fix invalid calls to drv_sta_pre_rcu_remove
Felix Fietkau [Fri, 24 Mar 2023 12:32:36 +0000 (13:32 +0100)]
mac80211: fix invalid calls to drv_sta_pre_rcu_remove

Potentially fixes some driver data structure corruption issues

Signed-off-by: Felix Fietkau <nbd@nbd.name>
21 months agobmips: sercomm,h500-s: add Quantenna network config
Álvaro Fernández Rojas [Fri, 24 Mar 2023 09:20:56 +0000 (10:20 +0100)]
bmips: sercomm,h500-s: add Quantenna network config

Sercomm H500-s has an external Quantenna QT3740BC SoC connected by RGMII.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
21 months agokernel: add more dsa b53 pending patches
Álvaro Fernández Rojas [Fri, 24 Mar 2023 09:05:23 +0000 (10:05 +0100)]
kernel: add more dsa b53 pending patches

These patches have now received a positive review upstream, so let's add them
to pending patches.

776-net-dsa-b53-mmap-add-phy-ops.patch:
  This is mostly bmips/bcm63xx-specific to get external switches working
  without hanging the device when accessing certain registers.

777-net-dsa-b53-mdio-add-support-for-BCM53134:
  This adds support for BCM53134 switch on DSA B53, so any target using DSA B53
  can benefit from it.

Also fix sercomm-h500-s external switch IMP port phy-mode.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
21 months agofirewall4: update to the latest version
Felix Fietkau [Fri, 24 Mar 2023 09:14:31 +0000 (10:14 +0100)]
firewall4: update to the latest version

39e8c70957c7 fw4: fix handling the ipset "comment" option
e6e82a55206c fw4: add further symbolic ICMP type declarations
ce9a37829a76 tests: add testcase for automatic includes
30ee17a9c65d fw4: fix syntax errors in ICMP type declarations
1ecfadd52291 fw4: remove accidentally committed .orig and .rej file
04a06bd70b98 fw4: enable flowtable counters

Signed-off-by: Felix Fietkau <nbd@nbd.name>
21 months agokernel: enable conntrack counter updates for iptables xt_FLOWOFFLOAD
Felix Fietkau [Thu, 23 Mar 2023 20:44:10 +0000 (21:44 +0100)]
kernel: enable conntrack counter updates for iptables xt_FLOWOFFLOAD

Ensures that packet/byte counters in /proc/net/nf_conntrack are updated

Signed-off-by: Felix Fietkau <nbd@nbd.name>
21 months agokernel: fix mediatek ppe flow accounting for mt7622 and older
Felix Fietkau [Thu, 23 Mar 2023 20:48:24 +0000 (21:48 +0100)]
kernel: fix mediatek ppe flow accounting for mt7622 and older

v1 hardware uses a different enable bit for hardware counters

Signed-off-by: Felix Fietkau <nbd@nbd.name>
21 months agokernel: report mediatek ppe flow stats incrementally
Felix Fietkau [Fri, 24 Mar 2023 09:09:09 +0000 (10:09 +0100)]
kernel: report mediatek ppe flow stats incrementally

Fixes wrong counter values in conntrack stats

Fixes: aa2777145f8d ("kernel: improve mtk ppe flow accounting")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
21 months agoodhcpd: bump to latest git HEAD
Christian Marangi [Fri, 24 Mar 2023 01:00:14 +0000 (02:00 +0100)]
odhcpd: bump to latest git HEAD

29c934d config: recheck have_link_local on interface reload if already init

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
21 months agompc85xx: Refresh patches
Hauke Mehrtens [Thu, 23 Mar 2023 23:42:04 +0000 (00:42 +0100)]
mpc85xx: Refresh patches

Make the patches apply cleanly again.

Fixes: ed82189339b8 ("mpc85xx: use bootwrapper for ws-ap3825i")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>