Emil Tantilov [Wed, 31 Jan 2018 00:51:22 +0000 (16:51 -0800)]
ixgbevf: add support for using order 1 pages to receive large frames
Based on commit
8649aaef4044
("igb: Add support for using order 1 pages to receive large frames")
Add support for using 3K buffers in order 1 page. We are reserving 1K for
now to have space available for future tail room and head room when we
enable build_skb support.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Wed, 31 Jan 2018 00:51:17 +0000 (16:51 -0800)]
ixgbevf: add ethtool private flag for legacy Rx
Introduce legacy-rx private flag that will allow switching between the
old and new (build_skb based) Rx code paths. The implementation is the
same as in commit
e08912985b29
("igb: Add support for ethtool private flag to allow use of legacy Rx")
This provides a means of validating the legacy Rx path in the event that
we are forced to fall back. At some point in the future when we are
convinced we don't need it anymore we might be able to drop the legacy-rx
flag.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Wed, 31 Jan 2018 00:51:12 +0000 (16:51 -0800)]
ixgbevf: use page_address offset from page
Based on commit
3456fd53421e
("igb: Use page_address offset from page instead of masking virtual address")
Update the handling of page addresses so that we always refer to them using
a void pointer, and try to use the consistent name of va indicating we are
working with a virtual address.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 29 Jan 2018 23:57:48 +0000 (15:57 -0800)]
ixgbe: prevent ptp_rx_hang from running when in FILTER_ALL mode
On hardware which supports timestamping all packets, the timestamps are
recorded in the packet buffer, and the driver no longer uses or reads
the registers. This makes the logic for checking and clearing Rx
timestamp hangs meaningless.
If we run the ixgbe_ptp_rx_hang() function in this case, then the driver
will continuously spam the log output with "Clearing Rx timestamp hang".
These messages are spurious, and confusing to end users.
The original code in commit
a9763f3cb54c ("ixgbe: Update PTP to support
X550EM_x devices", 2015-12-03) did have a flag PTP_RX_TIMESTAMP_IN_REGISTER
which was intended to be used to avoid the Rx timestamp hang check,
however it did not actually check the flag before calling the function.
Do so now in order to stop the checks and prevent the spurious log
messages.
Fixes: a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x devices", 2015-12-03)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tonghao Zhang [Sun, 28 Jan 2018 11:53:37 +0000 (03:53 -0800)]
ixgbe: Avoid to write the RETA table when unnecessary
If indir == 0 in the ixgbe_set_rxfh(), it is unnecessary
to write the HW. Because redirection table is not changed.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Colin Ian King [Tue, 16 Jan 2018 12:48:09 +0000 (12:48 +0000)]
ixgbe: remove redundant initialization of 'pool'
Variable pool is being assigned zero and then in the following for-loop
is it being set to zero again. Remove the redundant first assignment.
Cleans up clang warning:
drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c:61:2: warning: Value stored
to 'pool' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Sat, 24 Feb 2018 05:04:20 +0000 (00:04 -0500)]
Merge git://git./linux/kernel/git/davem/net
Linus Torvalds [Fri, 23 Feb 2018 23:14:17 +0000 (15:14 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix TTL offset calculation in mac80211 mesh code, from Peter Oh.
2) Fix races with procfs in ipt_CLUSTERIP, from Cong Wang.
3) Memory leak fix in lpm_trie BPF map code, from Yonghong Song.
4) Need to use GFP_ATOMIC in BPF cpumap allocations, from Jason Wang.
5) Fix potential deadlocks in netfilter getsockopt() code paths, from
Paolo Abeni.
6) Netfilter stackpointer size checks really are needed to validate
user input, from Florian Westphal.
7) Missing timer init in x_tables, from Paolo Abeni.
8) Don't use WQ_MEM_RECLAIM in mac80211 hwsim, from Johannes Berg.
9) When an ibmvnic device is brought down then back up again, it can be
sent queue entries from a previous session, handle this properly
instead of crashing. From Thomas Falcon.
10) Fix TCP checksum on LRO buffers in mlx5e, from Gal Pressman.
11) When we are dumping filters in cls_api, the output SKB is empty, and
the filter we are dumping is too large for the space in the SKB, we
should return -EMSGSIZE like other netlink dump operations do.
Otherwise userland has no signal that is needs to increase the size
of its read buffer. From Roman Kapl.
12) Several XDP fixes for virtio_net, from Jesper Dangaard Brouer.
13) Module refcount leak in netlink when a dump start fails, from Jason
Donenfeld.
14) Handle sub-optimal GSO sizes better in TCP BBR congestion control,
from Eric Dumazet.
15) Releasing bpf per-cpu arraymaps can take a long time, add a
condtional scheduling point. From Eric Dumazet.
16) Implement retpolines for tail calls in x64 and arm64 bpf JITs. From
Daniel Borkmann.
17) Fix page leak in gianfar driver, from Andy Spencer.
18) Missed clearing of estimator scratch buffer, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net_sched: gen_estimator: fix broken estimators based on percpu stats
gianfar: simplify FCS handling and fix memory leak
ipv6 sit: work around bogus gcc-8 -Wrestrict warning
macvlan: fix use-after-free in macvlan_common_newlink()
bpf, arm64: fix out of bounds access in tail call
bpf, x64: implement retpoline for tail call
rxrpc: Fix send in rxrpc_send_data_packet()
net: aquantia: Fix error handling in aq_pci_probe()
bpf: fix rcu lockdep warning for lpm_trie map_free callback
bpf: add schedule points in percpu arrays management
regulatory: add NUL to request alpha2
ibmvnic: Fix early release of login buffer
net/smc9194: Remove bogus CONFIG_MAC reference
net: ipv4: Set addr_type in hash_keys for forwarded case
tcp_bbr: better deal with suboptimal GSO
smsc75xx: fix smsc75xx_set_features()
netlink: put module reference if dump start fails
selftests/bpf/test_maps: exit child process without error in ENOMEM case
selftests/bpf: update gitignore with test_libbpf_open
selftests/bpf: tcpbpf_kern: use in6_* macros from glibc
..
Linus Torvalds [Fri, 23 Feb 2018 23:04:24 +0000 (15:04 -0800)]
Merge branch 'fixes-v4.16-rc3' of git://git./linux/kernel/git/jmorris/linux-security
Pull security subsystem fixes from James Morris:
- keys fixes via David Howells:
"A collection of fixes for Linux keyrings, mostly thanks to Eric
Biggers:
- Fix some PKCS#7 verification issues.
- Fix handling of unsupported crypto in X.509.
- Fix too-large allocation in big_key"
- Seccomp updates via Kees Cook:
"These are fixes for the get_metadata interface that landed during
-rc1. While the new selftest is strictly not a bug fix, I think
it's in the same spirit of avoiding bugs"
- an IMA build fix from Randy Dunlap
* 'fixes-v4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
integrity/security: fix digsig.c build error with header file
KEYS: Use individual pages in big_key for crypto buffers
X.509: fix NULL dereference when restricting key with unsupported_sig
X.509: fix BUG_ON() when hash algorithm is unsupported
PKCS#7: fix direct verification of SignerInfo signature
PKCS#7: fix certificate blacklisting
PKCS#7: fix certificate chain verification
seccomp: add a selftest for get_metadata
ptrace, seccomp: tweak get_metadata behavior slightly
seccomp, ptrace: switch get_metadata types to arch independent
Linus Torvalds [Fri, 23 Feb 2018 23:01:01 +0000 (15:01 -0800)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"arm64 and perf fixes:
- build error when accessing MPIDR_HWID_BITMASK from .S
- fix CTR_EL0 field definitions
- remove/disable some kernel messages on user faults (unhandled
signals, unimplemented syscalls)
- fix kernel page fault in unwind_frame() with function graph tracing
- fix perf sleeping while atomic errors when booting with ACPI"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: fix unwind_frame() for filtered out fn for function graph tracing
arm64: Enforce BBM for huge IO/VMAP mappings
arm64: perf: correct PMUVer probing
arm_pmu: acpi: request IRQs up-front
arm_pmu: note IRQs and PMUs per-cpu
arm_pmu: explicitly enable/disable SPIs at hotplug
arm_pmu: acpi: check for mismatched PPIs
arm_pmu: add armpmu_alloc_atomic()
arm_pmu: fold platform helpers into platform code
arm_pmu: kill arm_pmu_platdata
ARM: ux500: remove PMU IRQ bouncer
arm64: __show_regs: Only resolve kernel symbols when running at EL1
arm64: Remove unimplemented syscall log message
arm64: Disable unhandled signal log messages by default
arm64: cpufeature: Fix CTR_EL0 field definitions
arm64: uaccess: Formalise types for access_ok()
arm64: Fix compilation error while accessing MPIDR_HWID_BITMASK from .S files
Linus Torvalds [Fri, 23 Feb 2018 22:59:29 +0000 (14:59 -0800)]
Merge tag 'mips_fixes_4.16_3' of git://git./linux/kernel/git/jhogan/mips
Pull MIPS fix from James Hogan:
"A single MIPS fix for mismatching struct compat_flock, resulting in
bus errors starting Firefox on Debian 8 since 4.13"
* tag 'mips_fixes_4.16_3' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
MIPS: Drop spurious __unused in struct compat_flock
Linus Torvalds [Fri, 23 Feb 2018 22:57:20 +0000 (14:57 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/pmladek/printk
Pull printk fixlet from Petr Mladek:
"People expect to see the real pointer value for %px.
Let's substitute '(null)' only for the other %p? format modifiers that
need to deference the pointer"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
vsprintf: avoid misleading "(null)" for %px
Linus Torvalds [Fri, 23 Feb 2018 22:41:14 +0000 (14:41 -0800)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Two bugfixes, one v4.16 regression fix, and two documentation fixes"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Consider SCL GPIO optional
i2c: busses: i2c-sirf: Fix spelling: "formular" -> "formula".
i2c: bcm2835: Set up the rising/falling edge delays
i2c: i801: Add missing documentation entries for Braswell and Kaby Lake
i2c: designware: must wait for enable
Linus Torvalds [Fri, 23 Feb 2018 22:09:43 +0000 (14:09 -0800)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"These are mostly fixes for problems with merge window code.
In addition we have one doc update (alua) and two dead code removals
(aiclib and octogon) a spurious assignment removal (csiostor) and a
performance improvement for storvsc involving better interrupt
spreading and increasing the command per lun handling"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla4xxx: skip error recovery in case of register disconnect.
scsi: aacraid: fix shutdown crash when init fails
scsi: qedi: Cleanup local str variable
scsi: qedi: Fix truncation of CHAP name and secret
scsi: qla2xxx: Fix incorrect handle for abort IOCB
scsi: qla2xxx: Fix double free bug after firmware timeout
scsi: storvsc: Increase cmd_per_lun for higher speed devices
scsi: qla2xxx: Fix a locking imbalance in qlt_24xx_handle_els()
scsi: scsi_dh: Document alua_rtpg_queue() arguments
scsi: Remove Makefile entry for oktagon files
scsi: aic7xxx: remove aiclib.c
scsi: qla2xxx: Avoid triggering undefined behavior in qla2x00_mbx_completion()
scsi: mptfusion: Add bounds check in mptctl_hp_targetinfo()
scsi: sym53c8xx_2: iterator underflow in sym_getsync()
scsi: bnx2fc: Fix check in SCSI completion handler for timed out request
scsi: csiostor: remove redundant assignment to pointer 'ln'
scsi: ufs: Enable quirk to ignore sending WRITE_SAME command
scsi: ibmvfc: fix misdefined reserved field in ibmvfc_fcp_rsp_info
scsi: qla2xxx: Fix memory corruption during hba reset test
scsi: mpt3sas: fix an out of bound write
Donald Sharp [Fri, 23 Feb 2018 19:01:52 +0000 (14:01 -0500)]
net: fib_rules: Add new attribute to set protocol
For ages iproute2 has used `struct rtmsg` as the ancillary header for
FIB rules and in the process set the protocol value to RTPROT_BOOT.
Until
ca56209a66 ("net: Allow a rule to track originating protocol")
the kernel rules code ignored the protocol value sent from userspace
and always returned 0 in notifications. To avoid incompatibility with
existing iproute2, send the protocol as a new attribute.
Fixes: cac56209a66 ("net: Allow a rule to track originating protocol")
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 23 Feb 2018 18:31:31 +0000 (10:31 -0800)]
Merge tag 'drm-fixes-for-v4.16-rc3' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of fixes for rc3:
Exynos:
- fixes for using monotonic timestamps
- register definitions
- removal of unused file
ipu-v3L
- minor changes
- make some register arrays const+static
- fix some leaks
meson:
- fix for vsync
atomic:
- fix for memory leak
EDID parser:
- add quirks for some more non-desktop devices
- 6-bit panel fix.
drm_mm:
- fix a bug in the core drm mm hole handling
cirrus:
- fix lut loading regression
Lastly there is a deadlock fix around runtime suspend for secondary
GPUs.
There was a deadlock between one thread trying to wait for a workqueue
job to finish in the runtime suspend path, and the workqueue job it
was waiting for in turn waiting for a runtime_get_sync to return.
The fixes avoids it by not doing the runtime sync in the workqueue as
then we always wait for all those tasks to complete before we runtime
suspend"
* tag 'drm-fixes-for-v4.16-rc3' of git://people.freedesktop.org/~airlied/linux: (25 commits)
drm/tve200: fix kernel-doc documentation comment include
drm/edid: quirk Sony PlayStation VR headset as non-desktop
drm/edid: quirk Windows Mixed Reality headsets as non-desktop
drm/edid: quirk Oculus Rift headsets as non-desktop
drm/meson: fix vsync buffer update
drm: Handle unexpected holes in color-eviction
drm: exynos: Use proper macro definition for HDMI_I2S_PIN_SEL_1
drm/exynos: remove exynos_drm_rotator.h
drm/exynos: g2d: Delete an error message for a failed memory allocation in two functions
drm/exynos: fix comparison to bitshift when dealing with a mask
drm/exynos: g2d: use monotonic timestamps
drm/edid: Add 6 bpc quirk for CPT panel in Asus UX303LA
gpu: ipu-csi: add 10/12-bit grayscale support to mbus_code_to_bus_cfg
gpu: ipu-cpmem: add 16-bit grayscale support to ipu_cpmem_set_image
gpu: ipu-v3: prg: fix device node leak in ipu_prg_lookup_by_phandle
gpu: ipu-v3: pre: fix device node leak in ipu_pre_lookup_by_phandle
drm/amdgpu: Fix deadlock on runtime suspend
drm/radeon: Fix deadlock on runtime suspend
drm/nouveau: Fix deadlock on runtime suspend
drm: Allow determining if current task is output poll worker
...
Willem de Bruijn [Fri, 23 Feb 2018 16:56:20 +0000 (11:56 -0500)]
selftests/net: ignore background traffic in psock_fanout
The packet fanout test generates UDP traffic and reads this with
a pair of packet sockets, testing the various fanout algorithms.
Avoid non-determinism from reading unrelated background traffic.
Fanout decisions are made before unrelated packets can be dropped with
a filter, so that is an insufficient strategy [*]. Run the packet
socket tests in a network namespace, similar to msg_zerocopy.
It it still good practice to install a filter on a packet socket
before accepting traffic. Because this is example code, demonstrate
that pattern. Open the socket initially bound to no protocol, install
a filter, and only then bind to ETH_P_IP.
Another source of non-determinism is hash collisions in FANOUT_HASH.
The hash function used to select a socket in the fanout group includes
the pseudorandom number hashrnd, which is not visible from userspace.
To work around this, the test tries to find a pair of UDP source ports
that do not collide. It gives up too soon (5 times, every 32 runs) and
output is confusing. Increase tries to 20 and revise the error msg.
[*] another approach would be to add a third socket to the fanout
group and direct all unexpected traffic here. This is possible
only when reimplementing methods like RR or HASH alongside this
extra catch-all bucket, using the BPF fanout method.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 23 Feb 2018 12:22:52 +0000 (12:22 +0000)]
atm: idt77252: remove redundant bit-wise or'ing of zero
Zero is being bit-wise or'd in a calculation twice; these are redundant
and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 23 Feb 2018 03:45:27 +0000 (19:45 -0800)]
net_sched: gen_estimator: fix broken estimators based on percpu stats
pfifo_fast got percpu stats lately, uncovering a bug I introduced last
year in linux-4.10.
I missed the fact that we have to clear our temporary storage
before calling __gnet_stats_copy_basic() in the case of percpu stats.
Without this fix, rate estimators (tc qd replace dev xxx root est 1sec
4sec pfifo_fast) are utterly broken.
Fixes: 1c0d32fde5bd ("net_sched: gen_estimator: complete rewrite of rate estimators")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 23 Feb 2018 17:34:18 +0000 (12:34 -0500)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Alexei Starovoitov says:
====================
pull-request: bpf 2018-02-22
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) two urgent fixes for bpf_tail_call logic for x64 and arm64 JITs, from Daniel.
2) cond_resched points in percpu array alloc/free paths, from Eric.
3) lockdep and other minor fixes, from Yonghong, Arnd, Anders, Li.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Thu, 22 Feb 2018 21:40:27 +0000 (13:40 -0800)]
rds: rds_msg_zcopy should return error of null rm->data.op_mmp_znotifier
if either or both of MSG_ZEROCOPY and SOCK_ZEROCOPY have not been
specified, the rm->data.op_mmp_znotifier allocation will be skipped.
In this case, it is invalid ot pass down a cmsghdr with
RDS_CMSG_ZCOPY_COOKIE, so return EINVAL from rds_msg_zcopy for this
case.
Reported-by: syzbot+f893ae7bb2f6456dfbc3@syzkaller.appspotmail.com
Fixes: 0cebaccef3ac ("rds: zerocopy Tx support.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Thu, 22 Feb 2018 20:37:48 +0000 (21:37 +0100)]
r8169: simplify and improve check for dash
r8168_check_dash() returns false anyway for all chip versions not
supporting dash. So we can simplify the check conditions.
In addition change the check functions to return bool instead of int,
because they actually return a bool value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Thu, 22 Feb 2018 20:22:40 +0000 (21:22 +0100)]
r8169: disable WOL per default
Currently, if BIOS enables WOL in the chip, settings are inconsistent
because the device isn't marked as wakeup-enabled (if not done
explicitly via userspace tools). This causes issues with suspend/
resume because mdio_bus_phy_may_suspend() checks whether device is
wakeup-enabled. In detail MDIO bus access in phy_suspend() can fail
because the MDIO bus is disabled.
In the history of the driver we find two competing approaches:
8f9d5138035d "r8169: remember WOL preferences on driver load" prefers
to preserve what the BIOS may have set, whilst
bde135a672bf
"r8169: only enable PCI wakeups when WOL is active" disabled PCI
wakeup per default to work around a bug on one platform.
Seems like nobody complained after the latter patch about non-working
WOL, what makes me think that nobody uses WOL w/o configuring it
explicitly.
My opinion:
Vast majority of users doesn't use WOL even if the BIOS enables it in
the chip. And having WOL being active keeps the PHY(s) from powering
down if being idle.
If somebody needs WOL, he can enable it during boot, e.g. by
configuring systemd.link/WakeOnLan.
Therefore, to make WOL consistent again, disable it per default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Spencer [Thu, 22 Feb 2018 19:05:33 +0000 (11:05 -0800)]
gianfar: simplify FCS handling and fix memory leak
Previously, buffer descriptors containing only the frame check sequence
(FCS) were skipped and not added to the skb. However, the page reference
count was still incremented, leading to a memory leak.
Fixing this inside gfar_add_rx_frag() is difficult due to reserved
memory handling and page reuse. Instead, move the FCS handling to
gfar_process_frame() and trim off the FCS before passing the skb up the
networking stack.
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: Jim Gruen <jgruen@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 22 Feb 2018 15:55:34 +0000 (16:55 +0100)]
ipv6 sit: work around bogus gcc-8 -Wrestrict warning
gcc-8 has a new warning that detects overlapping input and output arguments
in memcpy(). It triggers for sit_init_net() calling ipip6_tunnel_clone_6rd(),
which is actually correct:
net/ipv6/sit.c: In function 'sit_init_net':
net/ipv6/sit.c:192:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
The problem here is that the logic detecting the memcpy() arguments finds them
to be the same, but the conditional that tests for the input and output of
ipip6_tunnel_clone_6rd() to be identical is not a compile-time constant.
We know that netdev_priv(t->dev) is the same as t for a tunnel device,
and comparing "dev" directly here lets the compiler figure out as well
that 'dev == sitn->fb_tunnel_dev' when called from sit_init_net(), so
it no longer warns.
This code is old, so Cc stable to make sure that we don't get the warning
for older kernels built with new gcc.
Cc: Martin Sebor <msebor@gmail.com>
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83456
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kodanev [Thu, 22 Feb 2018 15:20:30 +0000 (18:20 +0300)]
macvlan: fix use-after-free in macvlan_common_newlink()
The following use-after-free was reported by KASan when running
LTP macvtap01 test on 4.16-rc2:
[10642.528443] BUG: KASAN: use-after-free in
macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10642.626607] Read of size 8 at addr
ffff880ba49f2100 by task ip/18450
...
[10642.963873] Call Trace:
[10642.994352] dump_stack+0x5c/0x7c
[10643.035325] print_address_description+0x75/0x290
[10643.092938] kasan_report+0x28d/0x390
[10643.137971] ? macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10643.207963] macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10643.275978] macvtap_newlink+0x171/0x260 [macvtap]
[10643.334532] rtnl_newlink+0xd4f/0x1300
...
[10646.256176] Allocated by task 18450:
[10646.299964] kasan_kmalloc+0xa6/0xd0
[10646.343746] kmem_cache_alloc_trace+0xf1/0x210
[10646.397826] macvlan_common_newlink+0x6de/0x14a0 [macvlan]
[10646.464386] macvtap_newlink+0x171/0x260 [macvtap]
[10646.522728] rtnl_newlink+0xd4f/0x1300
...
[10647.022028] Freed by task 18450:
[10647.061549] __kasan_slab_free+0x138/0x180
[10647.111468] kfree+0x9e/0x1c0
[10647.147869] macvlan_port_destroy+0x3db/0x650 [macvlan]
[10647.211411] rollback_registered_many+0x5b9/0xb10
[10647.268715] rollback_registered+0xd9/0x190
[10647.319675] register_netdevice+0x8eb/0xc70
[10647.370635] macvlan_common_newlink+0xe58/0x14a0 [macvlan]
[10647.437195] macvtap_newlink+0x171/0x260 [macvtap]
Commit
d02fd6e7d293 ("macvlan: Fix one possible double free") handles
the case when register_netdevice() invokes ndo_uninit() on error and
as a result free the port. But 'macvlan_port_get_rtnl(dev))' check
(returns dev->rx_handler_data), which was added by this commit in order
to prevent double free, is not quite correct:
* for macvlan it always returns NULL because 'lowerdev' is the one that
was used to register rx handler (port) in macvlan_port_create() as
well as to unregister it in macvlan_port_destroy().
* for macvtap it always returns a valid pointer because macvtap registers
its own rx handler before macvlan_common_newlink().
Fixes: d02fd6e7d293 ("macvlan: Fix one possible double free")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pratyush Anand [Mon, 5 Feb 2018 13:28:01 +0000 (14:28 +0100)]
arm64: fix unwind_frame() for filtered out fn for function graph tracing
do_task_stat() calls get_wchan(), which further does unwind_frame().
unwind_frame() restores frame->pc to original value in case function
graph tracer has modified a return address (LR) in a stack frame to hook
a function return. However, if function graph tracer has hit a filtered
function, then we can't unwind it as ftrace_push_return_trace() has
biased the index(frame->graph) with a 'huge negative'
offset(-FTRACE_NOTRACE_DEPTH).
Moreover, arm64 stack walker defines index(frame->graph) as unsigned
int, which can not compare a -ve number.
Similar problem we can have with calling of walk_stackframe() from
save_stack_trace_tsk() or dump_backtrace().
This patch fixes unwind_frame() to test the index for -ve value and
restore index accordingly before we can restore frame->pc.
Reproducer:
cd /sys/kernel/debug/tracing/
echo schedule > set_graph_notrace
echo 1 > options/display-graph
echo wakeup > current_tracer
ps -ef | grep -i agent
Above commands result in:
Unable to handle kernel paging request at virtual address
ffff801bd3d1e000
pgd =
ffff8003cbe97c00
[
ffff801bd3d1e000] *pgd=
0000000000000000, *pud=
0000000000000000
Internal error: Oops:
96000006 [#1] SMP
[...]
CPU: 5 PID: 11696 Comm: ps Not tainted 4.11.0+ #33
[...]
task:
ffff8003c21ba000 task.stack:
ffff8003cc6c0000
PC is at unwind_frame+0x12c/0x180
LR is at get_wchan+0xd4/0x134
pc : [<
ffff00000808892c>] lr : [<
ffff0000080860b8>] pstate:
60000145
sp :
ffff8003cc6c3ab0
x29:
ffff8003cc6c3ab0 x28:
0000000000000001
x27:
0000000000000026 x26:
0000000000000026
x25:
00000000000012d8 x24:
0000000000000000
x23:
ffff8003c1c04000 x22:
ffff000008c83000
x21:
ffff8003c1c00000 x20:
000000000000000f
x19:
ffff8003c1bc0000 x18:
0000fffffc593690
x17:
0000000000000000 x16:
0000000000000001
x15:
0000b855670e2b60 x14:
0003e97f22cf1d0f
x13:
0000000000000001 x12:
0000000000000000
x11:
00000000e8f4883e x10:
0000000154f47ec8
x9 :
0000000070f367c0 x8 :
0000000000000000
x7 :
00008003f7290000 x6 :
0000000000000018
x5 :
0000000000000000 x4 :
ffff8003c1c03cb0
x3 :
ffff8003c1c03ca0 x2 :
00000017ffe80000
x1 :
ffff8003cc6c3af8 x0 :
ffff8003d3e9e000
Process ps (pid: 11696, stack limit = 0xffff8003cc6c0000)
Stack: (0xffff8003cc6c3ab0 to 0xffff8003cc6c4000)
[...]
[<
ffff00000808892c>] unwind_frame+0x12c/0x180
[<
ffff000008305008>] do_task_stat+0x864/0x870
[<
ffff000008305c44>] proc_tgid_stat+0x3c/0x48
[<
ffff0000082fde0c>] proc_single_show+0x5c/0xb8
[<
ffff0000082b27e0>] seq_read+0x160/0x414
[<
ffff000008289e6c>] __vfs_read+0x58/0x164
[<
ffff00000828b164>] vfs_read+0x88/0x144
[<
ffff00000828c2e8>] SyS_read+0x60/0xc0
[<
ffff0000080834a0>] __sys_trace_return+0x0/0x4
Fixes: 20380bb390a4 (arm64: ftrace: fix a stack tracer's output under function graph tracer)
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
[catalin.marinas@arm.com: replace WARN_ON with WARN_ON_ONCE]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Randy Dunlap [Tue, 13 Feb 2018 01:26:20 +0000 (17:26 -0800)]
integrity/security: fix digsig.c build error with header file
security/integrity/digsig.c has build errors on some $ARCH due to a
missing header file, so add it.
security/integrity/digsig.c:146:2: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: linux-integrity@vger.kernel.org
Link: http://kisskb.ellerman.id.au/kisskb/head/13396/
Signed-off-by: James Morris <james.morris@microsoft.com>
James Morris [Fri, 23 Feb 2018 03:55:46 +0000 (19:55 -0800)]
Merge tag 'keys-fixes-
20180222-2' of https://git./linux/kernel/git/dhowells/linux-fs into fixes-v4.16-rc3
Keyrings fixes.
Dave Airlie [Fri, 23 Feb 2018 01:11:57 +0000 (11:11 +1000)]
Merge tag 'imx-drm-next-2018-02-22' of git://git.pengutronix.de/git/pza/linux into drm-fixes
drm/imx: ipu-v3 fixups and grayscale support
- Make const interrupt register arrays static, reduces object size.
- Fix device_node leaks in PRE/PRG phandle lookup functions.
- Add 8-bit and 16-bit grayscale buffer support to ipu_cpmem_set_image,
- add 10-bit and 12-bit grayscale media bus support to ipu-csi,
to be used by the imx-media driver.
* tag 'imx-drm-next-2018-02-22' of git://git.pengutronix.de/git/pza/linux:
gpu: ipu-csi: add 10/12-bit grayscale support to mbus_code_to_bus_cfg
gpu: ipu-cpmem: add 16-bit grayscale support to ipu_cpmem_set_image
gpu: ipu-v3: prg: fix device node leak in ipu_prg_lookup_by_phandle
gpu: ipu-v3: pre: fix device node leak in ipu_pre_lookup_by_phandle
gpu: ipu-cpmem: add 8-bit grayscale support to ipu_cpmem_set_image
gpu: ipu-v3: make const arrays int_reg static, shrinks object size
Kees Cook [Fri, 23 Feb 2018 00:59:26 +0000 (16:59 -0800)]
MIPS: boot: Define __ASSEMBLY__ for its.S build
The MIPS %.its.S compiler command did not define __ASSEMBLY__, which meant
when compiler_types.h was added to kconfig.h, unexpected things appeared
(e.g. struct declarations) which should not have been present. As done in
the general %.S compiler command, __ASSEMBLY__ is now included here too.
The failure was:
Error: arch/mips/boot/vmlinux.gz.its:201.1-2 syntax error
FATAL ERROR: Unable to parse input tree
/usr/bin/mkimage: Can't read arch/mips/boot/vmlinux.gz.itb.tmp: Invalid argument
/usr/bin/mkimage Can't add hashes to FIT blob
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 28128c61e08e ("kconfig.h: Include compiler types to avoid missed struct attributes")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 23 Feb 2018 01:04:06 +0000 (17:04 -0800)]
Merge branch 'siginfo-linus' of git://git./linux/kernel/git/ebiederm/user-namespace
Pull siginfo fix from Eric Biederman:
"This fixes a build error that only shows up on blackfin"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
fs/signalfd: fix build error for BUS_MCEERR_AR
Linus Torvalds [Fri, 23 Feb 2018 00:38:10 +0000 (16:38 -0800)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"Fix an oops in the s5p-sss driver when used with ecb(aes)"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: s5p-sss - Fix kernel Oops in AES-ECB mode
Daniel Borkmann [Fri, 23 Feb 2018 00:03:43 +0000 (01:03 +0100)]
bpf, arm64: fix out of bounds access in tail call
I recently noticed a crash on arm64 when feeding a bogus index
into BPF tail call helper. The crash would not occur when the
interpreter is used, but only in case of JIT. Output looks as
follows:
[ 347.007486] Unable to handle kernel paging request at virtual address
fffb850e96492510
[...]
[ 347.043065] [
fffb850e96492510] address between user and kernel address ranges
[ 347.050205] Internal error: Oops:
96000004 [#1] SMP
[...]
[ 347.190829] x13:
0000000000000000 x12:
0000000000000000
[ 347.196128] x11:
fffc047ebe782800 x10:
ffff808fd7d0fd10
[ 347.201427] x9 :
0000000000000000 x8 :
0000000000000000
[ 347.206726] x7 :
0000000000000000 x6 :
001c991738000000
[ 347.212025] x5 :
0000000000000018 x4 :
000000000000ba5a
[ 347.217325] x3 :
00000000000329c4 x2 :
ffff808fd7cf0500
[ 347.222625] x1 :
ffff808fd7d0fc00 x0 :
ffff808fd7cf0500
[ 347.227926] Process test_verifier (pid: 4548, stack limit = 0x000000007467fa61)
[ 347.235221] Call trace:
[ 347.237656] 0xffff000002f3a4fc
[ 347.240784] bpf_test_run+0x78/0xf8
[ 347.244260] bpf_prog_test_run_skb+0x148/0x230
[ 347.248694] SyS_bpf+0x77c/0x1110
[ 347.251999] el0_svc_naked+0x30/0x34
[ 347.255564] Code:
9100075a d280220a 8b0a002a d37df04b (
f86b694b)
[...]
In this case the index used in BPF r3 is the same as in r1
at the time of the call, meaning we fed a pointer as index;
here, it had the value 0xffff808fd7cf0500 which sits in x2.
While I found tail calls to be working in general (also for
hitting the error cases), I noticed the following in the code
emission:
# bpftool p d j i 988
[...]
38: ldr w10, [x1,x10]
3c: cmp w2, w10
40: b.ge 0x000000000000007c <-- signed cmp
44: mov x10, #0x20 // #32
48: cmp x26, x10
4c: b.gt 0x000000000000007c
50: add x26, x26, #0x1
54: mov x10, #0x110 // #272
58: add x10, x1, x10
5c: lsl x11, x2, #3
60: ldr x11, [x10,x11] <-- faulting insn (
f86b694b)
64: cbz x11, 0x000000000000007c
[...]
Meaning, the tests passed because commit
ddb55992b04d ("arm64:
bpf: implement bpf_tail_call() helper") was using signed compares
instead of unsigned which as a result had the test wrongly passing.
Change this but also the tail call count test both into unsigned
and cap the index as u32. Latter we did as well in
90caccdd8cc0
("bpf: fix bpf_tail_call() x64 JIT") and is needed in addition here,
too. Tested on HiSilicon Hi1616.
Result after patch:
# bpftool p d j i 268
[...]
38: ldr w10, [x1,x10]
3c: add w2, w2, #0x0
40: cmp w2, w10
44: b.cs 0x0000000000000080
48: mov x10, #0x20 // #32
4c: cmp x26, x10
50: b.hi 0x0000000000000080
54: add x26, x26, #0x1
58: mov x10, #0x110 // #272
5c: add x10, x1, x10
60: lsl x11, x2, #3
64: ldr x11, [x10,x11]
68: cbz x11, 0x0000000000000080
[...]
Fixes: ddb55992b04d ("arm64: bpf: implement bpf_tail_call() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann [Thu, 22 Feb 2018 14:12:53 +0000 (15:12 +0100)]
bpf, x64: implement retpoline for tail call
Implement a retpoline [0] for the BPF tail call JIT'ing that converts
the indirect jump via jmp %rax that is used to make the long jump into
another JITed BPF image. Since this is subject to speculative execution,
we need to control the transient instruction sequence here as well
when CONFIG_RETPOLINE is set, and direct it into a pause + lfence loop.
The latter aligns also with what gcc / clang emits (e.g. [1]).
JIT dump after patch:
# bpftool p d x i 1
0: (18) r2 = map[id:1]
2: (b7) r3 = 0
3: (85) call bpf_tail_call#12
4: (b7) r0 = 2
5: (95) exit
With CONFIG_RETPOLINE:
# bpftool p d j i 1
[...]
33: cmp %edx,0x24(%rsi)
36: jbe 0x0000000000000072 |*
38: mov 0x24(%rbp),%eax
3e: cmp $0x20,%eax
41: ja 0x0000000000000072 |
43: add $0x1,%eax
46: mov %eax,0x24(%rbp)
4c: mov 0x90(%rsi,%rdx,8),%rax
54: test %rax,%rax
57: je 0x0000000000000072 |
59: mov 0x28(%rax),%rax
5d: add $0x25,%rax
61: callq 0x000000000000006d |+
66: pause |
68: lfence |
6b: jmp 0x0000000000000066 |
6d: mov %rax,(%rsp) |
71: retq |
72: mov $0x2,%eax
[...]
* relative fall-through jumps in error case
+ retpoline for indirect jump
Without CONFIG_RETPOLINE:
# bpftool p d j i 1
[...]
33: cmp %edx,0x24(%rsi)
36: jbe 0x0000000000000063 |*
38: mov 0x24(%rbp),%eax
3e: cmp $0x20,%eax
41: ja 0x0000000000000063 |
43: add $0x1,%eax
46: mov %eax,0x24(%rbp)
4c: mov 0x90(%rsi,%rdx,8),%rax
54: test %rax,%rax
57: je 0x0000000000000063 |
59: mov 0x28(%rax),%rax
5d: add $0x25,%rax
61: jmpq *%rax |-
63: mov $0x2,%eax
[...]
* relative fall-through jumps in error case
- plain indirect jump as before
[0] https://support.google.com/faqs/answer/
7625886
[1] https://github.com/gcc-mirror/gcc/commit/
a31e654fa107be968b802786d747e962c2fcdb2b
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Randy Dunlap [Mon, 12 Feb 2018 21:18:38 +0000 (13:18 -0800)]
fs/signalfd: fix build error for BUS_MCEERR_AR
Fix build error in fs/signalfd.c by using same method that is used in
kernel/signal.c: separate blocks for different signal si_code values.
./fs/signalfd.c: error: 'BUS_MCEERR_AR' undeclared (first use in this function)
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
David Howells [Thu, 22 Feb 2018 14:38:14 +0000 (14:38 +0000)]
rxrpc: Fix send in rxrpc_send_data_packet()
All the kernel_sendmsg() calls in rxrpc_send_data_packet() need to send
both parts of the iov[] buffer, but one of them does not. Fix it so that
it does.
Without this, short IPv6 rxrpc DATA packets may be seen that have the rxrpc
header included, but no payload.
Fixes: 5a924b8951f8 ("rxrpc: Don't store the rxrpc header in the Tx queue sk_buffs")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 22 Feb 2018 11:44:40 +0000 (12:44 +0100)]
dsa: ptp: mark dummy helpers as 'inline'
Declaring a static function in a header leads to a warning every
time that header gets included without the function being used:
In file included from drivers/net/dsa/mv88e6xxx/chip.c:42:
drivers/net/dsa/mv88e6xxx/ptp.h:92:13: error: 'mv88e6xxx_hwtstamp_work' defined but not used [-Werror=unused-function]
static long mv88e6xxx_hwtstamp_work(struct ptp_clock_info *ptp)
In file included from drivers/net/dsa/mv88e6xxx/chip.c:38:
drivers/net/dsa/mv88e6xxx/global2.h:355:12: error: 'mv88e6xxx_g2_wait' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_wait(struct mv88e6xxx_chip *chip, int reg, u16 mask)
^~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.h:350:12: error: 'mv88e6xxx_g2_update' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_update(struct mv88e6xxx_chip *chip, int reg, u16 update)
^~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.h:345:12: error: 'mv88e6xxx_g2_write' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_write(struct mv88e6xxx_chip *chip, int reg, u16 val)
^~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.h:340:12: error: 'mv88e6xxx_g2_read' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_read(struct mv88e6xxx_chip *chip, int reg, u16 *val)
This marks all such functions in dsa inline to make sure we don't warn
about them.
Fixes: c6fe0ad2c349 ("net: dsa: mv88e6xxx: add rx/tx timestamping support")
Fixes: 0d632c3d6fe3 ("net: dsa: mv88e6xxx: add accessors for PTP/TAI registers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 22 Feb 2018 09:11:55 +0000 (12:11 +0300)]
net: aquantia: Fix error handling in aq_pci_probe()
We should check "self->aq_hw" for allocation failure, and also we should
free it on the error paths.
Fixes: 23ee07ad3c2f ("net: aquantia: Cleanup pci functions module")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song [Thu, 22 Feb 2018 18:10:35 +0000 (10:10 -0800)]
bpf: fix rcu lockdep warning for lpm_trie map_free callback
Commit
9a3efb6b661f ("bpf: fix memory leak in lpm_trie map_free callback function")
fixed a memory leak and removed unnecessary locks in map_free callback function.
Unfortrunately, it introduced a lockdep warning. When lockdep checking is turned on,
running tools/testing/selftests/bpf/test_lpm_map will have:
[ 98.294321] =============================
[ 98.294807] WARNING: suspicious RCU usage
[ 98.295359] 4.16.0-rc2+ #193 Not tainted
[ 98.295907] -----------------------------
[ 98.296486] /home/yhs/work/bpf/kernel/bpf/lpm_trie.c:572 suspicious rcu_dereference_check() usage!
[ 98.297657]
[ 98.297657] other info that might help us debug this:
[ 98.297657]
[ 98.298663]
[ 98.298663] rcu_scheduler_active = 2, debug_locks = 1
[ 98.299536] 2 locks held by kworker/2:1/54:
[ 98.300152] #0: ((wq_completion)"events"){+.+.}, at: [<
00000000196bc1f0>] process_one_work+0x157/0x5c0
[ 98.301381] #1: ((work_completion)(&map->work)){+.+.}, at: [<
00000000196bc1f0>] process_one_work+0x157/0x5c0
Since actual trie tree removal happens only after no other
accesses to the tree are possible, replacing
rcu_dereference_protected(*slot, lockdep_is_held(&trie->lock))
with
rcu_dereference_protected(*slot, 1)
fixed the issue.
Fixes: 9a3efb6b661f ("bpf: fix memory leak in lpm_trie map_free callback function")
Reported-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Eric Dumazet [Thu, 22 Feb 2018 16:33:24 +0000 (08:33 -0800)]
bpf: add schedule points in percpu arrays management
syszbot managed to trigger RCU detected stalls in
bpf_array_free_percpu()
It takes time to allocate a huge percpu map, but even more time to free
it.
Since we run in process context, use cond_resched() to yield cpu if
needed.
Fixes: a10423b87a7e ("bpf: introduce BPF_MAP_TYPE_PERCPU_ARRAY map")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
David S. Miller [Thu, 22 Feb 2018 20:22:51 +0000 (15:22 -0500)]
Merge branch 'nfp-build-and-FW-initramfs-updates'
Jakub Kicinski says:
====================
nfp: build and FW initramfs updates
This set brings empty makefiles to allow building single object files
(useful for build-testing), Kbuild does not cater to this use case
too well. There are two ethernet drivers right now which suffer
from this (nfp, aquantia), both are fixed.
Dirk adds an uncommon FW image name to the list of firmware files
module may request.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dirk van der Merwe [Thu, 22 Feb 2018 03:50:07 +0000 (19:50 -0800)]
nfp: advertise firmware for mixed 10G/25G mode
The AMDA0099-0001 platform can support the 1x10G + 1x25G mixed mode
operation. Recently, firmware has been added for this configuration
mode.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 22 Feb 2018 03:50:06 +0000 (19:50 -0800)]
aquantia: add Makefiles to all directories
To be able to build separate objects we need to provide
Kbuild with a Makefile in each directory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 22 Feb 2018 03:50:05 +0000 (19:50 -0800)]
nfp: add Makefiles to all directories
To be able to build separate objects we need to provide
Kbuild with a Makefile in each directory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Feb 2018 20:18:28 +0000 (15:18 -0500)]
Merge tag 'mac80211-next-for-davem-2018-02-22' of git://git./linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Various updates across wireless.
One thing to note: I've included a new ethertype
that wireless uses (ETH_P_PREAUTH) in if_ether.h.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Feb 2018 20:17:01 +0000 (15:17 -0500)]
Merge tag 'mac80211-for-davem-2018-02-22' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes across the tree, the shortlog basically says it all:
cfg80211: fix cfg80211_beacon_dup
-> old bug in this code
cfg80211: clear wep keys after disconnection
-> certain ways of disconnecting left the keys
mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
-> alignment issues with using 14 bytes
mac80211: Do not disconnect on invalid operating class
-> if the AP has a bogus operating class, let it be
mac80211: Fix sending ADDBA response for an ongoing session
-> don't send the same frame twice
cfg80211: use only 1Mbps for basic rates in mesh
-> interop issue with old versions of our code
mac80211_hwsim: don't use WQ_MEM_RECLAIM
-> it causes splats because it flushes work on a non-reclaim WQ
regulatory: add NUL to request alpha2
-> nla_put_string() issue from Kees
mac80211: mesh: fix wrong mesh TTL offset calculation
-> protocol issue
mac80211: fix a possible leak of station stats
-> error path might leak memory
mac80211: fix calling sleeping function in atomic context
-> percpu allocations need to be made with gfp flags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilan Peer [Mon, 19 Feb 2018 12:48:41 +0000 (14:48 +0200)]
mac80211: Call mgd_prep_tx before transmitting deauthentication
In multi channel scenarios, when disassociating from the AP before a
beacon was heard from the AP, it is not guaranteed that the virtual
interface is granted air time for the transmission of the
deauthentication frame. This in turn can lead to various issues as
the AP might never get the deauthentication frame.
To mitigate such possible issues, add a HW flag indicating that the
driver requires mac80211 to call the mgd_prep_tx() driver callback
to make sure that the virtual interface is granted immediate airtime
to be able to transmit the frame, in case that no beacon was heard
from the AP.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sara Sharon [Mon, 19 Feb 2018 12:48:40 +0000 (14:48 +0200)]
mac80211: add get TID helper
Extracting the TID from the QOS header is common enough
to justify helper.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 19 Feb 2018 12:48:39 +0000 (14:48 +0200)]
mac80211: support reporting A-MPDU EOF bit value/known
Support getting the EOF bit value reported from hardware
and writing it out to radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Denis Kenzior [Thu, 1 Feb 2018 01:04:15 +0000 (19:04 -0600)]
uapi: Add 802.11 Preauthentication to if_ether
This adds 0x88c7 protocol type to if_ether.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Linus Torvalds [Thu, 22 Feb 2018 20:13:01 +0000 (12:13 -0800)]
Merge tag 'usb-4.16-rc3' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 4.16-rc3
Nothing major, but a number of different fixes all over the place in
the USB stack for reported issues. Mostly gadget driver fixes,
although the typical set of xhci bugfixes are there, along with some
new quirks additions as well.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (39 commits)
Revert "usb: musb: host: don't start next rx urb if current one failed"
usb: musb: fix enumeration after resume
usb: cdc_acm: prevent race at write to acm while system resumes
Add delay-init quirk for Corsair K70 RGB keyboards
usb: ohci: Proper handling of ed_rm_list to handle race condition between usb_kill_urb() and finish_unlinks()
usb: host: ehci: always enable interrupt for qtd completion at test mode
usb: ldusb: add PIDs for new CASSY devices supported by this driver
usb: renesas_usbhs: missed the "running" flag in usb_dmac with rx path
usb: host: ehci: use correct device pointer for dma ops
usbip: keep usbip_device sockfd state in sync with tcp_socket
ohci-hcd: Fix race condition caused by ohci_urb_enqueue() and io_watchdog_func()
USB: serial: option: Add support for Quectel EP06
xhci: fix xhci debugfs errors in xhci_stop
xhci: xhci debugfs device nodes weren't removed after device plugged out
xhci: Fix xhci debugfs devices node disappearance after hibernation
xhci: Fix NULL pointer in xhci debugfs
xhci: Don't print a warning when setting link state for disabled ports
xhci: workaround for AMD Promontory disabled ports wakeup
usb: dwc3: core: Fix ULPI PHYs and prevent phy_get/ulpi_init during suspend/resume
USB: gadget: udc: Add missing platform_device_put() on error in bdc_pci_probe()
...
Linus Torvalds [Thu, 22 Feb 2018 20:05:43 +0000 (12:05 -0800)]
Merge tag 'staging-4.16-rc2' of git://git./linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are a small number of staging and iio driver fixes for 4.16-rc2.
The IIO fixes are all for reported things, and the android driver
fixes also resolve some reported problems. The remaining fsl-mc
Kconfig change resolves a build testing error that Arnd reported.
All of these have been in linux-next with no reported issues"
* tag 'staging-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: buffer: check if a buffer has been set up when poll is called
iio: adis_lib: Initialize trigger before requesting interrupt
staging: android: ion: Zero CMA allocated memory
staging: android: ashmem: Fix a race condition in pin ioctls
staging: fsl-mc: fix build testing on x86
iio: srf08: fix link error "devm_iio_triggered_buffer_setup" undefined
staging: iio: ad5933: switch buffer mode to software
iio: adc: stm32: fix stm32h7_adc_enable error handling
staging: iio: adc: ad7192: fix external frequency setting
iio: adc: aspeed: Fix error handling path
Linus Torvalds [Thu, 22 Feb 2018 20:04:05 +0000 (12:04 -0800)]
Merge tag 'char-misc-4.16-rc3' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a handful of char/misc driver fixes for 4.16-rc3.
There are some binder driver fixes to resolve reported issues in
stress testing the recent binder changes, some extcon driver fixes,
and a few mei driver fixes and new device ids.
All of these, with the exception of the mei driver id additions, have
been in linux-next for a while. I forgot to push out the mei driver id
additions to kernel.org until today, but all build tests pass with
them enabled"
* tag 'char-misc-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: me: add cannon point device ids for 4th device
mei: me: add cannon point device ids
mei: set device client to the disconnected state upon suspend.
ANDROID: binder: synchronize_rcu() when using POLLFREE.
binder: replace "%p" with "%pK"
ANDROID: binder: remove WARN() for redundant txn error
binder: check for binder_thread allocation failure in binder_poll()
extcon: int3496: process id-pin first so that we start with the right status
Revert "extcon: axp288: Redo charger type detection a couple of seconds after probe()"
extcon: axp288: Constify the axp288_pwr_up_down_info array
Nathan Fontenot [Thu, 22 Feb 2018 03:33:56 +0000 (21:33 -0600)]
ibmvnic: Split counters for scrq/pools/napi
The approach of one counter to rule them all when tracking the number
of active sub-crqs, pools, and napi has problems handling some failover
scenarios. This is due to the split in initializing the sub crqs,
pools and napi in different places and the placement of updating
the active counts.
This patch simplifies this by having a counter for tx and rx
sub-crqs, pools, and napi.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Thu, 22 Feb 2018 19:55:28 +0000 (20:55 +0100)]
regulatory: add NUL to request alpha2
Similar to the ancient commit
a5fe8e7695dc ("regulatory: add NUL
to alpha2"), add another byte to alpha2 in the request struct so
that when we use nla_put_string(), we don't overrun anything.
Fixes: 73d54c9e74c4 ("cfg80211: add regulatory netlink multicast group")
Reported-by: Kees Cook <keescook@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Linus Torvalds [Thu, 22 Feb 2018 19:57:39 +0000 (11:57 -0800)]
Merge tag 'for-linus' of git://git./linux/kernel/git/rdma/rdma
Pull rdma fixes from Doug Ledford:
"Nothing in this is overly interesting, it's mostly your garden variety
fixes.
There was some work in this merge cycle around the new ioctl kABI, so
there are fixes in here related to that (probably with more to come).
We've also recently added new netlink support with a goal of moving
the primary means of configuring the entire subsystem to netlink
(eventually, this is a long term project), so there are fixes for
that.
Then a few bnxt_re driver fixes, and a few minor WARN_ON removals, and
that covers this pull request. There are already a few more fixes on
the list as of this morning, so there will certainly be more to come
in this rc cycle ;-)
Summary:
- Lots of fixes for the new IOCTL interface and general uverbs flow.
Found through testing and syzkaller
- Bugfixes for the new resource track netlink reporting
- Remove some unneeded WARN_ONs that were triggering for some users
in IPoIB
- Various fixes for the bnxt_re driver"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (27 commits)
RDMA/uverbs: Fix kernel panic while using XRC_TGT QP type
RDMA/bnxt_re: Avoid system hang during device un-reg
RDMA/bnxt_re: Fix system crash during load/unload
RDMA/bnxt_re: Synchronize destroy_qp with poll_cq
RDMA/bnxt_re: Unpin SQ and RQ memory if QP create fails
RDMA/bnxt_re: Disable atomic capability on bnxt_re adapters
RDMA/restrack: don't use uaccess_kernel()
RDMA/verbs: Check existence of function prior to accessing it
RDMA/vmw_pvrdma: Fix usage of user response structures in ABI file
RDMA/uverbs: Sanitize user entered port numbers prior to access it
RDMA/uverbs: Fix circular locking dependency
RDMA/uverbs: Fix bad unlock balance in ib_uverbs_close_xrcd
RDMA/restrack: Increment CQ restrack object before committing
RDMA/uverbs: Protect from command mask overflow
IB/uverbs: Fix unbalanced unlock on error path for rdma_explicit_destroy
IB/uverbs: Improve lockdep_check
RDMA/uverbs: Protect from races between lookup and destroy of uobjects
IB/uverbs: Hold the uobj write lock after allocate
IB/uverbs: Fix possible oops with duplicate ioctl attributes
IB/uverbs: Add ioctl support for 32bit processes
...
Linus Torvalds [Thu, 22 Feb 2018 19:53:17 +0000 (11:53 -0800)]
Merge tag 'riscv-for-linus-4.16-rc3-riscv_cleanups' of git://git./linux/kernel/git/palmer/riscv-linux
Pull RISC-V cleanups from Palmer Dabbelt:
"This contains a handful of small cleanups.
The only functional change is that IRQs are now enabled during
exception handling, which was found when some warnings triggered with
`CONFIG_DEBUG_ATOMIC_SLEEP=y`.
The remaining fixes should have no functional change: `sbi_save()` has
been renamed to `parse_dtb()` reflect what it actually does, and a
handful of unused Kconfig entries have been removed"
* tag 'riscv-for-linus-4.16-rc3-riscv_cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
Rename sbi_save to parse_dtb to improve code readability
RISC-V: Enable IRQ during exception handling
riscv: Remove ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE select
riscv: kconfig: Remove RISCV_IRQ_INTC select
riscv: Remove ARCH_WANT_OPTIONAL_GPIOLIB select
Andrew Lunn [Thu, 22 Feb 2018 00:51:49 +0000 (01:51 +0100)]
net: dsa: mv88e6xxx: scratch registers and external MDIO pins
MV88E6352 and later switches support GPIO control through the "Scratch
& Misc" global2 register. Two of the pins controlled this way on the
mv88e6390 family are the external MDIO pins. They can either by used
as part of the MII interface for port 0, GPIOs, or MDIO. Add a
function to configure them for MDIO, if possible, and call it when
registering the external MDIO bus.
Suggested-by: Russell King <rmk@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Thu, 22 Feb 2018 00:21:10 +0000 (18:21 -0600)]
ibmvnic: Fix TX descriptor tracking
With the recent change, transmissions that only needed
one descriptor were being missed. The result is that such
packets were tracked as outstanding transmissions but never
removed when its completion notification was received.
Fixes: ffc385b95adb ("ibmvnic: Keep track of supplementary TX descriptors")
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Thu, 22 Feb 2018 00:18:30 +0000 (18:18 -0600)]
ibmvnic: Fix early release of login buffer
The login buffer is released before the driver can perform
sanity checks between resources the driver requested and what
firmware will provide. Don't release the login buffer until
the sanity check is performed.
Fixes: 34f0f4e3f488 ("ibmvnic: Fix login buffer memory leaks")
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Wed, 21 Feb 2018 22:24:59 +0000 (09:24 +1100)]
net/smc9194: Remove bogus CONFIG_MAC reference
AFAIK the only version of smc9194.c with Mac support is the one in the
linux-mac68k CVS repo, which never made it to the mainline.
Despite that, from v2.3.45, arch/m68k/config.in listed CONFIG_SMC9194
under CONFIG_MAC. This mistake got carried over into Kconfig in v2.5.55.
(See pre-git era "[PATCH] add m68k dependencies to net driver config".)
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Feb 2018 19:38:38 +0000 (14:38 -0500)]
Merge tag 'mlx5-updates-2018-02-21' of git://git./linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-02-21
This series includes shared code updates for mlx5 core driver for both
netdev and rdma subsystems.
By Saeed,
First six patches of the series are meant to address a performance issue
and should provide a performance boost for multi core IRQ interrupt hungry
workloads. The issue is fixed in the first patch, all other patches are
meant to refactor the code in light of this fix.
The problem it comes to fix, is a shared spinlock accessed across all HCA
IRQs which protects the CQ database. To solve this we simply move the CQ
database and its spinlock to be per EQ (IRQ), thus per core.
By Yonatan,
Fragmented completion queue (CQ) for RDMA,
core driver implementation to create fragmented CQ buffers rather than
one large contiguous memory buffer, the implementation scheme already
exist and used by the netdev CQs, the patch shares that code with the
rdma CQ creation flow and makes use of the new API in mlx5_ib driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 21 Feb 2018 19:00:54 +0000 (11:00 -0800)]
net: ipv4: Set addr_type in hash_keys for forwarded case
The result of the skb flow dissect is copied from keys to hash_keys to
ensure only the intended data is hashed. The original L4 hash patch
overlooked setting the addr_type for this case; add it.
Fixes: bf4e0a3db97eb ("net: ipv4: add support for ECMP hash policy choice")
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 21 Feb 2018 14:43:03 +0000 (06:43 -0800)]
tcp_bbr: better deal with suboptimal GSO
BBR uses tcp_tso_autosize() in an attempt to probe what would be the
burst sizes and to adjust cwnd in bbr_target_cwnd() with following
gold formula :
/* Allow enough full-sized skbs in flight to utilize end systems. */
cwnd += 3 * bbr->tso_segs_goal;
But GSO can be lacking or be constrained to very small
units (ip link set dev ... gso_max_segs 2)
What we really want is to have enough packets in flight so that both
GSO and GRO are efficient.
So in the case GSO is off or downgraded, we still want to have the same
number of packets in flight as if GSO/TSO was fully operational, so
that GRO can hopefully be working efficiently.
To fix this issue, we make tcp_tso_autosize() unaware of
sk->sk_gso_max_segs
Only tcp_tso_segs() has to enforce the gso_max_segs limit.
Tested:
ethtool -K eth0 tso off gso off
tc qd replace dev eth0 root pfifo_fast
Before patch:
for f in {1..5}; do ./super_netperf 1 -H lpaa24 -- -K bbr; done
691 (ss -temoi shows cwnd is stuck around 6 )
667
651
631
517
After patch :
# for f in {1..5}; do ./super_netperf 1 -H lpaa24 -- -K bbr; done
1733 (ss -temoi shows cwnd is around 386 )
1778
1746
1781
1718
Fixes: 0f8782ea1497 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 21 Feb 2018 05:42:26 +0000 (21:42 -0800)]
smsc75xx: fix smsc75xx_set_features()
If an attempt is made to disable RX checksums, USB adapter is changed
but netdev->features is not, because smsc75xx_set_features() returns a
non zero value.
This throws errors from netdev_rx_csum_fault() :
<devname>: hw csum failure
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason A. Donenfeld [Wed, 21 Feb 2018 03:41:59 +0000 (04:41 +0100)]
netlink: put module reference if dump start fails
Before, if cb->start() failed, the module reference would never be put,
because cb->cb_running is intentionally false at this point. Users are
generally annoyed by this because they can no longer unload modules that
leak references. Also, it may be possible to tediously wrap a reference
counter back to zero, especially since module.c still uses atomic_inc
instead of refcount_inc.
This patch expands the error path to simply call module_put if
cb->start() fails.
Fixes: 41c87425a1ac ("netlink: do not set cb_running if dump's start() errs")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
James Morris [Thu, 22 Feb 2018 18:50:24 +0000 (10:50 -0800)]
Merge tag 'seccomp-v4.16-rc3' of https://git./linux/kernel/git/kees/linux into fixes-v4.16-rc3
- Fix seccomp GET_METADATA to deal with field sizes correctly (Tycho Andersen)
- Add selftest to make sure GET_METADATA doesn't regress (Tycho Andersen)
Linus Torvalds [Thu, 22 Feb 2018 18:45:46 +0000 (10:45 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"16 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: don't defer struct page initialization for Xen pv guests
lib/Kconfig.debug: enable RUNTIME_TESTING_MENU
vmalloc: fix __GFP_HIGHMEM usage for vmalloc_32 on 32b systems
selftests/memfd: add run_fuse_test.sh to TEST_FILES
bug.h: work around GCC PR82365 in BUG()
mm/swap.c: make functions and their kernel-doc agree (again)
mm/zpool.c: zpool_evictable: fix mismatch in parameter name and kernel-doc
ida: do zeroing in ida_pre_get()
mm, swap, frontswap: fix THP swap if frontswap enabled
certs/blacklist_nohashes.c: fix const confusion in certs blacklist
kernel/relay.c: limit kmalloc size to KMALLOC_MAX_SIZE
mm, mlock, vmscan: no more skipping pagevecs
mm: memcontrol: fix NR_WRITEBACK leak in memcg and system stats
Kbuild: always define endianess in kconfig.h
include/linux/sched/mm.h: re-inline mmdrop()
tools: fix cross-compile var clobbering
Luck, Tony [Thu, 22 Feb 2018 17:15:06 +0000 (09:15 -0800)]
efivarfs: Limit the rate for non-root to read files
Each read from a file in efivarfs results in two calls to EFI
(one to get the file size, another to get the actual data).
On X86 these EFI calls result in broadcast system management
interrupts (SMI) which affect performance of the whole system.
A malicious user can loop performing reads from efivarfs bringing
the system to its knees.
Linus suggested per-user rate limit to solve this.
So we add a ratelimit structure to "user_struct" and initialize
it for the root user for no limit. When allocating user_struct for
other users we set the limit to 100 per second. This could be used
for other places that want to limit the rate of some detrimental
user action.
In efivarfs if the limit is exceeded when reading, we take an
interruptible nap for 50ms and check the rate limit again.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kees Cook [Thu, 22 Feb 2018 17:41:40 +0000 (09:41 -0800)]
kconfig.h: Include compiler types to avoid missed struct attributes
The header files for some structures could get included in such a way
that struct attributes (specifically __randomize_layout from path.h) would
be parsed as variable names instead of attributes. This could lead to
some instances of a structure being unrandomized, causing nasty GPFs, etc.
This patch makes sure the compiler_types.h header is included in
kconfig.h so that we've always got types and struct attributes defined,
since kconfig.h is included from the compiler command line.
Reported-by: Patrick McLean <chutzpah@gentoo.org>
Root-caused-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Fixes: 3859a271a003 ("randstruct: Mark various structs for randomization")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H.J. Lu [Wed, 7 Feb 2018 22:20:09 +0000 (14:20 -0800)]
x86: Treat R_X86_64_PLT32 as R_X86_64_PC32
On i386, there are 2 types of PLTs, PIC and non-PIC. PIE and shared
objects must use PIC PLT. To use PIC PLT, you need to load
_GLOBAL_OFFSET_TABLE_ into EBX first. There is no need for that on
x86-64 since x86-64 uses PC-relative PLT.
On x86-64, for 32-bit PC-relative branches, we can generate PLT32
relocation, instead of PC32 relocation, which can also be used as
a marker for 32-bit PC-relative branches. Linker can always reduce
PLT32 relocation to PC32 if function is defined locally. Local
functions should use PC32 relocation. As far as Linux kernel is
concerned, R_X86_64_PLT32 can be treated the same as R_X86_64_PC32
since Linux kernel doesn't use PLT.
R_X86_64_PLT32 for 32-bit PC-relative branches has been enabled in
binutils master branch which will become binutils 2.31.
[ hjl is working on having better documentation on this all, but a few
more notes from him:
"PLT32 relocation is used as marker for PC-relative branches. Because
of EBX, it looks odd to generate PLT32 relocation on i386 when EBX
doesn't have GOT.
As for symbol resolution, PLT32 and PC32 relocations are almost
interchangeable. But when linker sees PLT32 relocation against a
protected symbol, it can resolved locally at link-time since it is
used on a branch instruction. Linker can't do that for PC32
relocation"
but for the kernel use, the two are basically the same, and this
commit gets things building and working with the current binutils
master - Linus ]
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Thu, 22 Feb 2018 14:38:34 +0000 (14:38 +0000)]
KEYS: Use individual pages in big_key for crypto buffers
kmalloc() can't always allocate large enough buffers for big_key to use for
crypto (1MB + some metadata) so we cannot use that to allocate the buffer.
Further, vmalloc'd pages can't be passed to sg_init_one() and the aead
crypto accessors cannot be called progressively and must be passed all the
data in one go (which means we can't pass the data in one block at a time).
Fix this by allocating the buffer pages individually and passing them
through a multientry scatterlist to the crypto layer. This has the bonus
advantage that we don't have to allocate a contiguous series of pages.
We then vmap() the page list and pass that through to the VFS read/write
routines.
This can trigger a warning:
WARNING: CPU: 0 PID: 60912 at mm/page_alloc.c:3883 __alloc_pages_nodemask+0xb7c/0x15f8
([<
00000000002acbb6>] __alloc_pages_nodemask+0x1ee/0x15f8)
[<
00000000002dd356>] kmalloc_order+0x46/0x90
[<
00000000002dd3e0>] kmalloc_order_trace+0x40/0x1f8
[<
0000000000326a10>] __kmalloc+0x430/0x4c0
[<
00000000004343e4>] big_key_preparse+0x7c/0x210
[<
000000000042c040>] key_create_or_update+0x128/0x420
[<
000000000042e52c>] SyS_add_key+0x124/0x220
[<
00000000007bba2c>] system_call+0xc4/0x2b0
from the keyctl/padd/useradd test of the keyutils testsuite on s390x.
Note that it might be better to shovel data through in page-sized lumps
instead as there's no particular need to use a monolithic buffer unless the
kernel itself wants to access the data.
Fixes: 13100a72f40f ("Security: Keys: Big keys stored encrypted")
Reported-by: Paul Bunyan <pbunyan@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Kirill Marinushkin <k.marinushkin@gmail.com>
Eric Biggers [Thu, 22 Feb 2018 14:38:34 +0000 (14:38 +0000)]
X.509: fix NULL dereference when restricting key with unsupported_sig
The asymmetric key type allows an X.509 certificate to be added even if
its signature's hash algorithm is not available in the crypto API. In
that case 'payload.data[asym_auth]' will be NULL. But the key
restriction code failed to check for this case before trying to use the
signature, resulting in a NULL pointer dereference in
key_or_keyring_common() or in restrict_link_by_signature().
Fix this by returning -ENOPKG when the signature is unsupported.
Reproducer when all the CONFIG_CRYPTO_SHA512* options are disabled and
keyctl has support for the 'restrict_keyring' command:
keyctl new_session
keyctl restrict_keyring @s asymmetric builtin_trusted
openssl req -new -sha512 -x509 -batch -nodes -outform der \
| keyctl padd asymmetric desc @s
Fixes: a511e1af8b12 ("KEYS: Move the point of trust determination to __key_link()")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Eric Biggers [Thu, 22 Feb 2018 14:38:33 +0000 (14:38 +0000)]
X.509: fix BUG_ON() when hash algorithm is unsupported
The X.509 parser mishandles the case where the certificate's signature's
hash algorithm is not available in the crypto API. In this case,
x509_get_sig_params() doesn't allocate the cert->sig->digest buffer;
this part seems to be intentional. However,
public_key_verify_signature() is still called via
x509_check_for_self_signed(), which triggers the 'BUG_ON(!sig->digest)'.
Fix this by making public_key_verify_signature() return -ENOPKG if the
hash buffer has not been allocated.
Reproducer when all the CONFIG_CRYPTO_SHA512* options are disabled:
openssl req -new -sha512 -x509 -batch -nodes -outform der \
| keyctl padd asymmetric desc @s
Fixes: 6c2dc5ae4ab7 ("X.509: Extract signature digest and make self-signed cert checks earlier")
Reported-by: Paolo Valente <paolo.valente@linaro.org>
Cc: Paolo Valente <paolo.valente@linaro.org>
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Eric Biggers [Thu, 22 Feb 2018 14:38:33 +0000 (14:38 +0000)]
PKCS#7: fix direct verification of SignerInfo signature
If none of the certificates in a SignerInfo's certificate chain match a
trusted key, nor is the last certificate signed by a trusted key, then
pkcs7_validate_trust_one() tries to check whether the SignerInfo's
signature was made directly by a trusted key. But, it actually fails to
set the 'sig' variable correctly, so it actually verifies the last
signature seen. That will only be the SignerInfo's signature if the
certificate chain is empty; otherwise it will actually be the last
certificate's signature.
This is not by itself a security problem, since verifying any of the
certificates in the chain should be sufficient to verify the SignerInfo.
Still, it's not working as intended so it should be fixed.
Fix it by setting 'sig' correctly for the direct verification case.
Fixes: 757932e6da6d ("PKCS#7: Handle PKCS#7 messages that contain no X.509 certs")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Eric Biggers [Thu, 22 Feb 2018 14:38:33 +0000 (14:38 +0000)]
PKCS#7: fix certificate blacklisting
If there is a blacklisted certificate in a SignerInfo's certificate
chain, then pkcs7_verify_sig_chain() sets sinfo->blacklisted and returns
0. But, pkcs7_verify() fails to handle this case appropriately, as it
actually continues on to the line 'actual_ret = 0;', indicating that the
SignerInfo has passed verification. Consequently, PKCS#7 signature
verification ignores the certificate blacklist.
Fix this by not considering blacklisted SignerInfos to have passed
verification.
Also fix the function comment with regards to when 0 is returned.
Fixes: 03bb79315ddc ("PKCS#7: Handle blacklisted certificates")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Eric Biggers [Thu, 22 Feb 2018 14:38:33 +0000 (14:38 +0000)]
PKCS#7: fix certificate chain verification
When pkcs7_verify_sig_chain() is building the certificate chain for a
SignerInfo using the certificates in the PKCS#7 message, it is passing
the wrong arguments to public_key_verify_signature(). Consequently,
when the next certificate is supposed to be used to verify the previous
certificate, the next certificate is actually used to verify itself.
An attacker can use this bug to create a bogus certificate chain that
has no cryptographic relationship between the beginning and end.
Fortunately I couldn't quite find a way to use this to bypass the
overall signature verification, though it comes very close. Here's the
reasoning: due to the bug, every certificate in the chain beyond the
first actually has to be self-signed (where "self-signed" here refers to
the actual key and signature; an attacker might still manipulate the
certificate fields such that the self_signed flag doesn't actually get
set, and thus the chain doesn't end immediately). But to pass trust
validation (pkcs7_validate_trust()), either the SignerInfo or one of the
certificates has to actually be signed by a trusted key. Since only
self-signed certificates can be added to the chain, the only way for an
attacker to introduce a trusted signature is to include a self-signed
trusted certificate.
But, when pkcs7_validate_trust_one() reaches that certificate, instead
of trying to verify the signature on that certificate, it will actually
look up the corresponding trusted key, which will succeed, and then try
to verify the *previous* certificate, which will fail. Thus, disaster
is narrowly averted (as far as I could tell).
Fixes: 6c2dc5ae4ab7 ("X.509: Extract signature digest and make self-signed cert checks earlier")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Li Zhijian [Thu, 22 Feb 2018 02:34:02 +0000 (10:34 +0800)]
selftests/bpf/test_maps: exit child process without error in ENOMEM case
test_maps contains a series of stress tests, and previously it will break the
rest tests when it failed to alloc memory.
-----------------------
Failed to create hashmap key=8 value=262144 'Cannot allocate memory'
Failed to create hashmap key=16 value=262144 'Cannot allocate memory'
Failed to create hashmap key=8 value=262144 'Cannot allocate memory'
Failed to create hashmap key=8 value=262144 'Cannot allocate memory'
test_maps: test_maps.c:955: run_parallel: Assertion `status == 0' failed.
Aborted
not ok 1..3 selftests: test_maps [FAIL]
-----------------------
after this patch, the rest tests will be continue when it occurs an ENOMEM failure
CC: Alexei Starovoitov <alexei.starovoitov@gmail.com>
CC: Philip Li <philip.li@intel.com>
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Li Zhijian <zhijianx.li@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Will Deacon [Wed, 21 Feb 2018 12:59:27 +0000 (12:59 +0000)]
arm64: Enforce BBM for huge IO/VMAP mappings
ioremap_page_range doesn't honour break-before-make and attempts to put
down huge mappings (using p*d_set_huge) over the top of pre-existing
table entries. This leads to us leaking page table memory and also gives
rise to TLB conflicts and spurious aborts, which have been seen in
practice on Cortex-A75.
Until this has been resolved, refuse to put block mappings when the
existing entry is found to be present.
Fixes: 324420bf91f60 ("arm64: add support for ioremap() block mappings")
Reported-by: Hanjun Guo <hanjun.guo@linaro.org>
Reported-by: Lei Li <lious.lilei@hisilicon.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Andy Shevchenko [Sat, 17 Feb 2018 20:58:43 +0000 (22:58 +0200)]
i2c: designware: Consider SCL GPIO optional
GPIO library can return -ENOSYS for the failed request.
Instead of failing ->probe() in this case override error code to 0.
Fixes: ca382f5b38f3 ("i2c: designware: add i2c gpio recovery option")
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Patryk Kocielnik [Fri, 26 Jan 2018 20:19:26 +0000 (21:19 +0100)]
i2c: busses: i2c-sirf: Fix spelling: "formular" -> "formula".
Fix spelling.
Signed-off-by: Patryk Kocielnik <patryk.kocielnik@gmail.com>
[wsa: fixed "Initialization", too]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Eric Anholt [Thu, 8 Feb 2018 13:54:05 +0000 (14:54 +0100)]
i2c: bcm2835: Set up the rising/falling edge delays
We were leaving them in the power on state (or the state the firmware
had set up for some client, if we were taking over from them). The
boot state was 30 core clocks, when we actually want to sample some
time after (to make sure that the new input bit has actually arrived).
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Tycho Andersen [Wed, 21 Feb 2018 02:47:47 +0000 (19:47 -0700)]
seccomp: add a selftest for get_metadata
Let's test that we get the flags correctly, and that we preserve the filter
index across the ptrace(PTRACE_SECCOMP_GET_METADATA) correctly.
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
CC: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Tycho Andersen [Wed, 21 Feb 2018 02:47:46 +0000 (19:47 -0700)]
ptrace, seccomp: tweak get_metadata behavior slightly
Previously if users passed a small size for the input structure size, they
would get get odd behavior. It doesn't make sense to pass a structure
smaller than at least filter_off size, so let's just give -EINVAL in this
case.
This changes userspace visible behavior, but was only introduced in commit
26500475ac1b ("ptrace, seccomp: add support for retrieving seccomp
metadata") in 4.16-rc2, so should be safe to change if merged before then.
Reported-by: Eugene Syromiatnikov <esyr@redhat.com>
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
CC: Kees Cook <keescook@chromium.org>
CC: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Tycho Andersen [Wed, 21 Feb 2018 02:47:45 +0000 (19:47 -0700)]
seccomp, ptrace: switch get_metadata types to arch independent
Commit
26500475ac1b ("ptrace, seccomp: add support for retrieving seccomp
metadata") introduced `struct seccomp_metadata`, which contained unsigned
longs that should be arch independent. The type of the flags member was
chosen to match the corresponding argument to seccomp(), and so we need
something at least as big as unsigned long. My understanding is that __u64
should fit the bill, so let's switch both types to that.
While this is userspace facing, it was only introduced in 4.16-rc2, and so
should be safe assuming it goes in before then.
Reported-by: "Dmitry V. Levin" <ldv@altlinux.org>
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
CC: Kees Cook <keescook@chromium.org>
CC: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: "Dmitry V. Levin" <ldv@altlinux.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Anders Roxell [Wed, 21 Feb 2018 21:30:01 +0000 (22:30 +0100)]
selftests/bpf: update gitignore with test_libbpf_open
bpf builds a test program for loading BPF ELF files. Add the executable
to the .gitignore list.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Daniel Díaz <daniel.diaz@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Anders Roxell [Wed, 21 Feb 2018 16:51:16 +0000 (17:51 +0100)]
selftests/bpf: tcpbpf_kern: use in6_* macros from glibc
Both glibc and the kernel have in6_* macros definitions. Build fails
because it picks up wrong in6_* macro from the kernel header and not the
header from glibc.
Fixes build error below:
clang -I. -I./include/uapi -I../../../include/uapi
-Wno-compare-distinct-pointer-types \
-O2 -target bpf -emit-llvm -c test_tcpbpf_kern.c -o - | \
llc -march=bpf -mcpu=generic -filetype=obj
-o .../tools/testing/selftests/bpf/test_tcpbpf_kern.o
In file included from test_tcpbpf_kern.c:12:
.../netinet/in.h:101:5: error: expected identifier
IPPROTO_HOPOPTS = 0, /* IPv6 Hop-by-Hop options. */
^
.../linux/in6.h:131:26: note: expanded from macro 'IPPROTO_HOPOPTS'
^
In file included from test_tcpbpf_kern.c:12:
/usr/include/netinet/in.h:103:5: error: expected identifier
IPPROTO_ROUTING = 43, /* IPv6 routing header. */
^
.../linux/in6.h:132:26: note: expanded from macro 'IPPROTO_ROUTING'
^
In file included from test_tcpbpf_kern.c:12:
.../netinet/in.h:105:5: error: expected identifier
IPPROTO_FRAGMENT = 44, /* IPv6 fragmentation header. */
^
Since both glibc and the kernel have in6_* macros definitions, use the
one from glibc. Kernel headers will check for previous libc definitions
by including include/linux/libc-compat.h.
Reported-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Arnd Bergmann [Tue, 20 Feb 2018 22:07:33 +0000 (23:07 +0100)]
bpf: clean up unused-variable warning
The only user of this variable is inside of an #ifdef, causing
a warning without CONFIG_INET:
net/core/filter.c: In function '____bpf_sock_ops_cb_flags_set':
net/core/filter.c:3382:6: error: unused variable 'val' [-Werror=unused-variable]
int val = argval & BPF_SOCK_OPS_ALL_CB_FLAGS;
This replaces the #ifdef with a nicer IS_ENABLED() check that
makes the code more readable and avoids the warning.
Fixes: b13d88072172 ("bpf: Adds field bpf_sock_ops_cb_flags to tcp_sock")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Juergen Gross [Wed, 21 Feb 2018 22:46:09 +0000 (14:46 -0800)]
mm: don't defer struct page initialization for Xen pv guests
Commit
f7f99100d8d9 ("mm: stop zeroing memory during allocation in
vmemmap") broke Xen pv domains in some configurations, as the "Pinned"
information in struct page of early page tables could get lost.
This will lead to the kernel trying to write directly into the page
tables instead of asking the hypervisor to do so. The result is a crash
like the following:
BUG: unable to handle kernel paging request at
ffff8801ead19008
IP: xen_set_pud+0x4e/0xd0
PGD
1c0a067 P4D
1c0a067 PUD
23a0067 PMD
1e9de0067 PTE
80100001ead19065
Oops: 0003 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.14.0-default+ #271
Hardware name: Dell Inc. Latitude E6440/0159N7, BIOS A07 06/26/2014
task:
ffffffff81c10480 task.stack:
ffffffff81c00000
RIP: e030:xen_set_pud+0x4e/0xd0
Call Trace:
__pmd_alloc+0x128/0x140
ioremap_page_range+0x3f4/0x410
__ioremap_caller+0x1c3/0x2e0
acpi_os_map_iomem+0x175/0x1b0
acpi_tb_acquire_table+0x39/0x66
acpi_tb_validate_table+0x44/0x7c
acpi_tb_verify_temp_table+0x45/0x304
acpi_reallocate_root_table+0x12d/0x141
acpi_early_init+0x4d/0x10a
start_kernel+0x3eb/0x4a1
xen_start_kernel+0x528/0x532
Code: 48 01 e8 48 0f 42 15 a2 fd be 00 48 01 d0 48 ba 00 00 00 00 00 ea ff ff 48 c1 e8 0c 48 c1 e0 06 48 01 d0 48 8b 00 f6 c4 02 75 5d <4c> 89 65 00 5b 5d 41 5c c3 65 8b 05 52 9f fe 7e 89 c0 48 0f a3
RIP: xen_set_pud+0x4e/0xd0 RSP:
ffffffff81c03cd8
CR2:
ffff8801ead19008
---[ end trace
38eca2e56f1b642e ]---
Avoid this problem by not deferring struct page initialization when
running as Xen pv guest.
Pavel said:
: This is unique for Xen, so this particular issue won't effect other
: configurations. I am going to investigate if there is a way to
: re-enable deferred page initialization on xen guests.
[akpm@linux-foundation.org: explicitly include xen.h]
Link: http://lkml.kernel.org/r/20180216154101.22865-1-jgross@suse.com
Fixes: f7f99100d8d95d ("mm: stop zeroing memory during allocation in vmemmap")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Cc: Steven Sistare <steven.sistare@oracle.com>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Bob Picco <bob.picco@oracle.com>
Cc: <stable@vger.kernel.org> [4.15.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anders Roxell [Wed, 21 Feb 2018 22:46:05 +0000 (14:46 -0800)]
lib/Kconfig.debug: enable RUNTIME_TESTING_MENU
Commit
d3deafaa8b5c ("lib/: make RUNTIME_TESTS a menuconfig to ease
disabling it all") causes a regression when using runtime tests due to
it defaults RUNTIME_TESTING_MENU to not set.
Link: http://lkml.kernel.org/r/20180214133015.10090-1-anders.roxell@linaro.org
Fixes: d3deafaa8b5c ("lib/: make RUNTIME_TESTS a menuconfig to easedisabling it all")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Cc: Vincent Legoll <vincent.legoll@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Byungchul Park <byungchul.park@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Wed, 21 Feb 2018 22:46:01 +0000 (14:46 -0800)]
vmalloc: fix __GFP_HIGHMEM usage for vmalloc_32 on 32b systems
Kai Heng Feng has noticed that BUG_ON(PageHighMem(pg)) triggers in
drivers/media/common/saa7146/saa7146_core.c since
19809c2da28a ("mm,
vmalloc: use __GFP_HIGHMEM implicitly").
saa7146_vmalloc_build_pgtable uses vmalloc_32 and it is reasonable to
expect that the resulting page is not in highmem. The above commit
aimed to add __GFP_HIGHMEM only for those requests which do not specify
any zone modifier gfp flag. vmalloc_32 relies on GFP_VMALLOC32 which
should do the right thing. Except it has been missed that GFP_VMALLOC32
is an alias for GFP_KERNEL on 32b architectures. Thanks to Matthew to
notice this.
Fix the problem by unconditionally setting GFP_DMA32 in GFP_VMALLOC32
for !64b arches (as a bailout). This should do the right thing and use
ZONE_NORMAL which should be always below 4G on 32b systems.
Debugged by Matthew Wilcox.
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/20180212095019.GX21609@dhcp22.suse.cz
Fixes: 19809c2da28a ("mm, vmalloc: use __GFP_HIGHMEM implicitly”)
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Kai Heng Feng <kai.heng.feng@canonical.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anders Roxell [Wed, 21 Feb 2018 22:45:58 +0000 (14:45 -0800)]
selftests/memfd: add run_fuse_test.sh to TEST_FILES
While testing memfd tests, there is a missing script, as reported by
kselftest:
./run_tests.sh: line 7: ./run_fuse_test.sh: No such file or directory
Link: http://lkml.kernel.org/r/1517955779-11386-1-git-send-email-daniel.diaz@linaro.org
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Wed, 21 Feb 2018 22:45:54 +0000 (14:45 -0800)]
bug.h: work around GCC PR82365 in BUG()
Looking at functions with large stack frames across all architectures
led me discovering that BUG() suffers from the same problem as
fortify_panic(), which I've added a workaround for already.
In short, variables that go out of scope by calling a noreturn function
or __builtin_unreachable() keep using stack space in functions
afterwards.
A workaround that was identified is to insert an empty assembler
statement just before calling the function that doesn't return. I'm
adding a macro "barrier_before_unreachable()" to document this, and
insert calls to that in all instances of BUG() that currently suffer
from this problem.
The files that saw the largest change from this had these frame sizes
before, and much less with my patch:
fs/ext4/inode.c:82:1: warning: the frame size of 1672 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/namei.c:434:1: warning: the frame size of 904 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/super.c:2279:1: warning: the frame size of 1160 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/xattr.c:146:1: warning: the frame size of 1168 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/f2fs/inode.c:152:1: warning: the frame size of 1424 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_core.c:1195:1: warning: the frame size of 1068 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_core.c:395:1: warning: the frame size of 1084 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_ftp.c:298:1: warning: the frame size of 928 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_ftp.c:418:1: warning: the frame size of 908 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_lblcr.c:718:1: warning: the frame size of 960 bytes is larger than 800 bytes [-Wframe-larger-than=]
drivers/net/xen-netback/netback.c:1500:1: warning: the frame size of 1088 bytes is larger than 800 bytes [-Wframe-larger-than=]
In case of ARC and CRIS, it turns out that the BUG() implementation
actually does return (or at least the compiler thinks it does),
resulting in lots of warnings about uninitialized variable use and
leaving noreturn functions, such as:
block/cfq-iosched.c: In function 'cfq_async_queue_prio':
block/cfq-iosched.c:3804:1: error: control reaches end of non-void function [-Werror=return-type]
include/linux/dmaengine.h: In function 'dma_maxpq':
include/linux/dmaengine.h:1123:1: error: control reaches end of non-void function [-Werror=return-type]
This makes them call __builtin_trap() instead, which should normally
dump the stack and kill the current process, like some of the other
architectures already do.
I tried adding barrier_before_unreachable() to panic() and
fortify_panic() as well, but that had very little effect, so I'm not
submitting that patch.
Vineet said:
: For ARC, it is double win.
:
: 1. Fixes 3 -Wreturn-type warnings
:
: | ../net/core/ethtool.c:311:1: warning: control reaches end of non-void function
: [-Wreturn-type]
: | ../kernel/sched/core.c:3246:1: warning: control reaches end of non-void function
: [-Wreturn-type]
: | ../include/linux/sunrpc/svc_xprt.h:180:1: warning: control reaches end of
: non-void function [-Wreturn-type]
:
: 2. bloat-o-meter reports code size improvements as gcc elides the
: generated code for stack return.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82365
Link: http://lkml.kernel.org/r/20171219114112.939391-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc]
Tested-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc]
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christopher Li <sparse@chrisli.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Rapoport [Wed, 21 Feb 2018 22:45:50 +0000 (14:45 -0800)]
mm/swap.c: make functions and their kernel-doc agree (again)
There was a conflict between the commit
e02a9f048ef7 ("mm/swap.c: make
functions and their kernel-doc agree") and the commit
f144c390f905 ("mm:
docs: fix parameter names mismatch") that both tried to fix mismatch
betweeen pagevec_lookup_entries() parameter names and their description.
Since nr_entries is a better name for the parameter, fix the description
again.
Link: http://lkml.kernel.org/r/1518116946-20947-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Rapoport [Wed, 21 Feb 2018 22:45:46 +0000 (14:45 -0800)]
mm/zpool.c: zpool_evictable: fix mismatch in parameter name and kernel-doc
[akpm@linux-foundation.org: add colon, per Randy]
Link: http://lkml.kernel.org/r/1518116984-21141-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rasmus Villemoes [Wed, 21 Feb 2018 22:45:43 +0000 (14:45 -0800)]
ida: do zeroing in ida_pre_get()
As far as I can tell, the only place the per-cpu ida_bitmap is populated
is in ida_pre_get. The pre-allocated element is stolen in two places in
ida_get_new_above, in both cases immediately followed by a memset(0).
Since ida_get_new_above is called with locks held, do the zeroing in
ida_pre_get, or rather let kmalloc() do it. Also, apparently gcc
generates ~44 bytes of code to do a memset(, 0, 128):
$ scripts/bloat-o-meter vmlinux.{0,1}
add/remove: 0/0 grow/shrink: 2/1 up/down: 5/-88 (-83)
Function old new delta
ida_pre_get 115 119 +4
vermagic 27 28 +1
ida_get_new_above 715 627 -88
Link: http://lkml.kernel.org/r/20180108225634.15340-1-linux@rasmusvillemoes.dk
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Eric Biggers <ebiggers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Huang Ying [Wed, 21 Feb 2018 22:45:39 +0000 (14:45 -0800)]
mm, swap, frontswap: fix THP swap if frontswap enabled
It was reported by Sergey Senozhatsky that if THP (Transparent Huge
Page) and frontswap (via zswap) are both enabled, when memory goes low
so that swap is triggered, segfault and memory corruption will occur in
random user space applications as follow,
kernel: urxvt[338]: segfault at 20 ip
00007fc08889ae0d sp
00007ffc73a7fc40 error 6 in libc-2.26.so[
7fc08881a000+1ae000]
#0 0x00007fc08889ae0d _int_malloc (libc.so.6)
#1 0x00007fc08889c2f3 malloc (libc.so.6)
#2 0x0000560e6004bff7 _Z14rxvt_wcstoutf8PKwi (urxvt)
#3 0x0000560e6005e75c n/a (urxvt)
#4 0x0000560e6007d9f1 _ZN16rxvt_perl_interp6invokeEP9rxvt_term9hook_typez (urxvt)
#5 0x0000560e6003d988 _ZN9rxvt_term9cmd_parseEv (urxvt)
#6 0x0000560e60042804 _ZN9rxvt_term6pty_cbERN2ev2ioEi (urxvt)
#7 0x0000560e6005c10f _Z17ev_invoke_pendingv (urxvt)
#8 0x0000560e6005cb55 ev_run (urxvt)
#9 0x0000560e6003b9b9 main (urxvt)
#10 0x00007fc08883af4a __libc_start_main (libc.so.6)
#11 0x0000560e6003f9da _start (urxvt)
After bisection, it was found the first bad commit is
bd4c82c22c36 ("mm,
THP, swap: delay splitting THP after swapped out").
The root cause is as follows:
When the pages are written to swap device during swapping out in
swap_writepage(), zswap (fontswap) is tried to compress the pages to
improve performance. But zswap (frontswap) will treat THP as a normal
page, so only the head page is saved. After swapping in, tail pages
will not be restored to their original contents, causing memory
corruption in the applications.
This is fixed by refusing to save page in the frontswap store functions
if the page is a THP. So that the THP will be swapped out to swap
device.
Another choice is to split THP if frontswap is enabled. But it is found
that the frontswap enabling isn't flexible. For example, if
CONFIG_ZSWAP=y (cannot be module), frontswap will be enabled even if
zswap itself isn't enabled.
Frontswap has multiple backends, to make it easy for one backend to
enable THP support, the THP checking is put in backend frontswap store
functions instead of the general interfaces.
Link: http://lkml.kernel.org/r/20180209084947.22749-1-ying.huang@intel.com
Fixes: bd4c82c22c367e068 ("mm, THP, swap: delay splitting THP after swapped out")
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Suggested-by: Minchan Kim <minchan@kernel.org> [put THP checking in backend]
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Shaohua Li <shli@kernel.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: <stable@vger.kernel.org> [4.14]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andi Kleen [Wed, 21 Feb 2018 22:45:35 +0000 (14:45 -0800)]
certs/blacklist_nohashes.c: fix const confusion in certs blacklist
const must be marked __initconst, not __initdata.
Link: http://lkml.kernel.org/r/20171222001335.1987-1-andi@firstfloor.org
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Wed, 21 Feb 2018 22:45:32 +0000 (14:45 -0800)]
kernel/relay.c: limit kmalloc size to KMALLOC_MAX_SIZE
chan->n_subbufs is set by the user and relay_create_buf() does a kmalloc()
of chan->n_subbufs * sizeof(size_t *).
kmalloc_slab() will generate a warning when this fails if
chan->subbufs * sizeof(size_t *) > KMALLOC_MAX_SIZE.
Limit chan->n_subbufs to the maximum allowed kmalloc() size.
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1802061216100.122576@chino.kir.corp.google.com
Fixes: f6302f1bcd75 ("relay: prevent integer overflow in relay_open()")
Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>