Stijn Tintel [Tue, 28 Jun 2022 21:00:51 +0000 (00:00 +0300)]
kernel: add missing symbol to 5.10 config
Kernel 5.10.124 introduced a new symbol 'LIB_MEMNEQ'. Add it to the
generic 5.10 config.
Fixes: 9e5d743422ed ("kernel: bump 5.10 to 5.10.124")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Luiz Angelo Daros de Luca [Thu, 23 Jun 2022 20:50:03 +0000 (17:50 -0300)]
realtek: add DGS-1210-28 factory image
DGS-1210 switches support dual image, with each image composed of a
kernel and a rootfs partition. For image1, kernel and rootfs are in
sequence. The current OpenWrt image (written using a serial console),
uses those partitions together as the firmware partition, ignoring the
partition division. The current OEM u-boot fails to validate image1 but
it will only trigger firmware recovery if both image1 and image2 fail,
and it does not switch the boot image in case one of them fails the
check.
The OEM factory image is composed of concatenated blocks of data, each
one prefixed with a 0x40-byte cameo header. A normal OEM firmware will
have two of these blocks (kernel, rootfs). The OEM firmware only checks
the header before writing unconditionally the data (except the header)
to the correspoding partition.
The OpenWrt factory image mimics the OEM image by cutting the
kernel+rootfs firmware at the exact size of the OEM kernel partition
and packing it as "the kernel partition" and the rest of the kernel and
the rootfs as "the rootfs partition". It will only work if written to
image1 because image2 has a sysinfo partition between kernel2 and
rootfs2, cutting the kernel code in the middle.
Steps to install:
1) switch to image2 (containing an OEM image), using web or these CLI
commands:
- config firmware image_id 2 boot_up
- reboot
2) flash the factory_image1.bin to image1. OEM web (v6.30.016)
is crashing for any upload (ssh keys, firmware), even applying OEM
firmwares. These CLI commands can upload a new firmware to the other
image location (not used to boot):
- download firmware_fromTFTP <tftpserver> factory_image1.bin
- config firmware image_id 1 boot_up
- reboot
To debrick the device, you'll need serial access. If you want to
recover to an OpenWrt, you can replay the serial installation
instructions. For returning to the original firmware, press ESC during
the boot to trigger the emergency firmware recovery procedure. After
that, use D-Link Network Assistant v2.0.2.4 to flash a new firmware.
The device documentation does describe that holding RESET for 12s
trigger the firmware recovery. However, the latest shipped U-Boot
"2011.12.(2.1.5.67086)-Candidate1" from "Aug 24 2021 - 17:33:09" cannot
trigger that from a cold boot. In fact, any U-Boot procedure that relies
on the RESET button, like reset settings, will only work if started from
a running original firmware. That, in practice, cancels the benefit of
having two images and a firmware recovery procedure (if you are not
consider dual-booting OpenWrt).
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Luiz Angelo Daros de Luca [Fri, 24 Jun 2022 19:05:16 +0000 (16:05 -0300)]
scripts: add cameo image header generator
The cameo header is a 0x40-byte header used by D-Link DGS 1210 switches
and Apresia ApresiaLightGS series. cameo-imghdr.py is a clean-room
reimplementation of imghdr present in the DGS-1210-28-GPL package.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
[fix board_version argument's help text]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Stijn Tintel [Tue, 28 Jun 2022 19:14:29 +0000 (22:14 +0300)]
hostapd: disable mbo by default
Enabling mbo by default on 802.11ax devices breaks for encryption types
that do not enable 802.11w by default. Disable mbo by default to fix
this. Enabling mbo by default on 802.11ax devices was not explained in
the commit message anyway.
Fixes: 6eee9836565c ("hostapd: introduce mbo option")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Sven Hauer [Mon, 27 Jun 2022 20:25:12 +0000 (22:25 +0200)]
ath79: support for TP-Link EAP225 v4
This model is almost identical to the EAP225 v3.
Major difference is the RTL8211FS PHY Chipset.
Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (RTL8211FS): 1× 1GbE, 802.3at PoE
Flashing instructions:
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
Do NOT bridge R230.
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via LuCI web interface
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
Signed-off-by: Sven Hauer <sven.hauer+github@uniku.de>
Stijn Tintel [Mon, 27 Jun 2022 14:06:34 +0000 (17:06 +0300)]
hostapd: introduce min_tx_power option
Introduce a new option min_tx_power to configure the minimum permitted
max TX power (in dBm) for ACS and DFS channel selection.
Imagine the following regulatory rules:
* 5180 MHz [36] (21.0 dBm)
* 5200 MHz [40] (21.0 dBm)
* 5220 MHz [44] (21.0 dBm)
* 5240 MHz [48] (21.0 dBm)
* 5260 MHz [52] (20.0 dBm) (radar detection)
* 5280 MHz [56] (20.0 dBm) (radar detection)
* 5300 MHz [60] (20.0 dBm) (radar detection)
* 5320 MHz [64] (20.0 dBm) (radar detection)
* 5500 MHz [100] (21.0 dBm) (radar detection)
* 5520 MHz [104] (21.0 dBm) (radar detection)
* 5540 MHz [108] (21.0 dBm) (radar detection)
* 5560 MHz [112] (21.0 dBm) (radar detection)
* 5580 MHz [116] (21.0 dBm) (radar detection)
* 5600 MHz [120] (21.0 dBm) (radar detection)
* 5620 MHz [124] (21.0 dBm) (radar detection)
* 5640 MHz [128] (21.0 dBm) (radar detection)
* 5660 MHz [132] (21.0 dBm) (radar detection)
* 5680 MHz [136] (21.0 dBm) (radar detection)
* 5700 MHz [140] (21.0 dBm) (radar detection)
* 5720 MHz [144] (13.0 dBm) (radar detection)
* 5745 MHz [149] (13.0 dBm)
* 5765 MHz [153] (13.0 dBm)
* 5785 MHz [157] (13.0 dBm)
* 5805 MHz [161] (13.0 dBm)
* 5825 MHz [165] (13.0 dBm)
* 5845 MHz [169] (13.0 dBm)
* 5865 MHz [173] (13.0 dBm)
When ACS or DFS end up selecting channel 144 or higher, some clients
might no longer be able to communicate with the AP due to the TX power
being limited to 13 dBm. Setting min_tx_power to 20 will result in
hostapd not considering these channels during ACS or after a DFS event.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Stijn Tintel [Mon, 6 Jun 2022 13:36:27 +0000 (16:36 +0300)]
hostapd: introduce background_radar option
Introduce a new option background_radar to toggle hostapd's background
radar feature. Enabling this allows DFS CAC to run on dedicated radio RF
chains while the radio(s) are otherwise running normal AP activities on
other channels.
As OpenWrt configures hostapd to use a channel list even when a single
channel is configured, using this feature requires a list of channels in
/etc/config/wireless. Alternatively, channel can be set to auto.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Stijn Tintel [Fri, 3 Jun 2022 08:22:50 +0000 (11:22 +0300)]
hostapd: support MBO in bss_transition_request
Support the use of MBO in the bss_transition_request ubus method.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Stijn Tintel [Mon, 6 Jun 2022 13:54:00 +0000 (16:54 +0300)]
hostapd: introduce mbo option
Introduce a new option mbo to toggle Multi Band Operation aka Agile
Multiband for a BSS.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Stijn Tintel [Mon, 20 Jun 2022 16:25:22 +0000 (19:25 +0300)]
hostapd: enable MBO if 802.11ax is enabled
Multi Band Operation is required for 802.11ax certification, so let's
enable it if 802.11ax support is enabled.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Stijn Tintel [Mon, 20 Jun 2022 16:23:18 +0000 (19:23 +0300)]
hostapd: add config symbol to enable MBO
Multi Band Operation aka Agile Multiband introduces new Transition
and Transition Rejection Reason Codes that should improve client
steering. Add a config symbol to enable it, and enable it by default for
the full variants.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Sander Vanheule [Mon, 27 Jun 2022 18:36:32 +0000 (20:36 +0200)]
kernel: backport RTL8211F clkout-disable patch
In Linux v5.14 an extra feature was introduced for the RTL8211F phy,
allowing to disable a clock output from the phy. Part of that patch is to
always (soft) reset the phy upon initialisation.
This phy reset is required to have a working ethernet on the TP-Link
EAP225-Outdoor v3 and EAP225 v4 after a reboot. Otherwise the ethernet
port will only function properly on cold boots.
Tested-by: Andre Klärner <kandre@ak-online.be> # EAP225-Outdoor v3
Tested-by: Sven Hauer <sven.hauer+github@uniku.de> # EAP225 v4
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Sander Vanheule [Mon, 27 Jun 2022 19:24:24 +0000 (21:24 +0200)]
firmware-utils: bump to git HEAD
The support-list partition for the EAP225-V3 board ID became larger than
the allocated size, resulting in factory image generation for the
EAP225-Outdoor v3 and EAP225 v3 to fail. The make directive
Build/tplink-safeloader ignores this failure however, resulting in a
seemingly successful build with empty factory images.
Included changes:
e609c5d75186 tplink-safeloader: drop unqualified EAP225-V3 IDs
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tiago Gaspar [Thu, 23 Jun 2022 13:15:06 +0000 (14:15 +0100)]
ath10k: enable encapsulation offload by default
Enable ath10k offload by default. This improves wireless performance
without requiring user configuration.
This adds ath10k_core to the AUTOLOAD section so that the frame_mode
paramter can be added to /etc/modules.d and passed to the driver.
The frame_mode 2 enables ethernet mode on the firmware/driver.
This parameter is set by passing a different value to the frame_mode
value on kmod insmod.
Link to the original patchset:
https://patchwork.kernel.org/project/linux-wireless/cover/
20220516032519.29831-1-ryazanov.s.a@gmail.com/
Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
Martin Blumenstingl [Sat, 25 Jun 2022 19:19:22 +0000 (21:19 +0200)]
lantiq: dts: td-w8980: Remove duplicate PCI properties
lantiq,bus-clock, interrupt-map-mask and interrupt-map are already
defined with these exact values in vr9.dtsi. Drop them from
vr9_tplink_tdw8980.dts to just have one place where these are
maintained.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Rui Salvaterra [Wed, 22 Jun 2022 13:12:26 +0000 (14:12 +0100)]
kernel: bump 5.15 to 5.15.49
Deleted (upstreamed):
generic/backport-5.15/702-v5.19-34-net-ethernet-mtk_eth_soc-fix-misuse-of-mem-alloc-int.patch [1]
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.49&id=
fcba12a4308143f1f1dcb0face8b3ffb51edcc5c
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Rui Salvaterra [Thu, 16 Jun 2022 16:06:51 +0000 (17:06 +0100)]
kernel: bump 5.15 to 5.15.48
No patches needed rebasing.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Rui Salvaterra [Mon, 20 Jun 2022 09:50:45 +0000 (10:50 +0100)]
kernel: bump 5.15 to 5.15.47
Deleted (upstreamed):
generic/backport-5.15/702-v5.19-32-net-ethernet-mtk_eth_soc-out-of-bounds-read-in-mtk_h.patch [01]
[01] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.47&id=
b24ca1cf846273361d5bd73a35de95a486a54b6d
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[Removed 702-v5.19-32-net-ethernet-mtk_eth_soc-out-of-bounds-read-in-mtk_h.patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rui Salvaterra [Thu, 9 Jun 2022 13:19:03 +0000 (14:19 +0100)]
kernel: bump 5.15 to 5.15.46
Deleted (upstreamed):
generic/backport-5.15/400-mtdblock-warn-if-opened-on-NAND.patch [01]
generic/backport-5.15/420-v5.19-01-mtd-spinand-gigadevice-fix-Quad-IO-for-GD5F1GQ5UExxG.patch [02]
bcm27xx/patches-5.15/950-0029-Revert-mailbox-avoid-timer-start-from-callback.patch [03]
bcm27xx/patches-5.15/950-0417-bcm2711_thermal-Don-t-clamp-temperature-at-zero.patch [04]
bcm27xx/patches-5.15/950-0740-drm-vc4-hvs-Fix-frame-count-register-readout.patch [05]
bcm27xx/patches-5.15/950-0755-drm-vc4-hvs-Reset-muxes-at-probe-time.patch [06]
bcm27xx/patches-5.15/950-0759-drm-vc4-txp-Don-t-set-TXP_VSTART_AT_EOF.patch [07]
bcm27xx/patches-5.15/950-0760-drm-vc4-txp-Force-alpha-to-be-0xff-if-it-s-disabled.patch [08]
bcm53xx/patches-5.15/031-v5.17-0005-ARM-dts-BCM5301X-update-CRU-block-description.patch [09]
mediatek/patches-5.15/102-mt7629-enable-arch-timer.patch [10]
Manually rebased:
bcm27xx/patches-5.15/950-0741-drm-vc4-hvs-Use-pointer-to-HVS-in-HVS_READ-and-HVS_W.patch
[01] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=
f41c9418c5898c01634675150696da290fb86796
[02] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=
d5b66645305c6f3a1b2cf75cee4157b07f293309
[03] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=
119f99209d8531359bcb935f252ec435f9d21b13
[04] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=
c4e1280abead1552e1764684079a43e222ccd163
[05] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=
08465a1889cb48ec64431e9db745b5be15399251
[06] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=
0e26a6da02e63b75b629573d13966c36aa6264f0
[07] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=
01c9020b2e7c85e394879f34851805179ac3d1d8
[08] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=
d47f85cc0171a5d3c5bd8cbb8a98983ca3357cbd
[09] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=
5151f24ac937ff7eb1f078257c66e3c0f0296010
[10] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=
ffea838686b82fbb2801cdfad6ba5309d15c032d
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Rui Salvaterra [Fri, 10 Jun 2022 08:07:31 +0000 (09:07 +0100)]
kernel: 5.15: x86-64: enable CONFIG_SLS
Starting with GCC 12, we have the possibility of mitigating straight-line
speculation vulnerabilities in x86-64 targets. Make it so.
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
John Audia [Sat, 25 Jun 2022 17:28:25 +0000 (13:28 -0400)]
kernel: bump 5.10 to 5.10.125
All patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Wed, 22 Jun 2022 15:58:33 +0000 (11:58 -0400)]
kernel: bump 5.10 to 5.10.124
All patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Thu, 16 Jun 2022 18:47:54 +0000 (14:47 -0400)]
kernel: bump 5.10 to 5.10.123
No patches required a rebase, just updated checksum.
Build system: x86_64
Build-tested: ipq806x/R7800
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Tue, 14 Jun 2022 19:31:10 +0000 (15:31 -0400)]
kernel: bump 5.10 to 5.10.122
All patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Sat, 11 Jun 2022 12:50:59 +0000 (08:50 -0400)]
kernel: bump 5.10 to 5.10.121
Manually rebased:
oxnas/patches-5.10/100-oxnas-clk-plla-pllb.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Signed-off-by: John Audia <therealgraysky@proton.me>
Rui Salvaterra [Mon, 23 May 2022 09:59:30 +0000 (10:59 +0100)]
valgrind: bump to 3.19.0
Patches automatically rebased.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Josef Schlehofer [Wed, 15 Jun 2022 14:31:12 +0000 (16:31 +0200)]
opkg: update to 2022-02-24
Changes:
9c44557 opkg_remove: avoid remove pkg repeatly with option --force-removal-of-dependent-packages
2edcfad libopkg: set 'const' attribute for argv
This should fix the CI error in the packages repository, which happens with perl.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Konstantin Demin [Mon, 20 Jun 2022 07:37:15 +0000 (10:37 +0300)]
dropbear: cherry-pick upstream commit
544f28a0
Resolves #10081
Reported-By: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Rosen Penev [Tue, 21 Jun 2022 04:09:08 +0000 (21:09 -0700)]
tools/meson: update to 0.61.5
Mostly backports by a Red Hat employee as 0.62 and newer demands Python
3.7+. Same reason 0.61 is kept here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Nick Hainke [Sat, 25 Jun 2022 14:24:18 +0000 (16:24 +0200)]
arptables: update to 0.0.5 and cleanup
Update to 0.0.5:
efae894 arptables 0.0.5 release
1f3c6bc libarptc: Simplify alloc_handle by using calloc()
4e5e23a Eliminate compiler warning about size passed to strncmp()
bf11d72 Add .gitignore
28b22d5 arptables: legacy renaming
988d6a4 arptables: cleanup sysvinit script
f4ab8f6 src: Remove support for libc5
047f37b src: Use stdint types
4bb2f83 arptables: Add MARK target
dbbe9f7 arptables: Add revision field for arptables userspace
935acea src: fix compilation warning
5700dbf src: cache in tree and use x_tables.h
4b7d6b0 arptables: remove dead dynamic hooks code
c299484 arptables: fix potential buffer overflow (author: dcb)
9fcaf70 arptables: add missing long option --set-counters and update documentation
36daba3 arptables: install man pages
f79b957 Add man pages for arptables-{save,restore}
c492c16 add GPL text
8f58693 fix potential buffer overflows reported by static analysis
ee4ec13 make static analysis tool happy (false positive)
b064d44 build an libarptc.a archive
Cleanup Makefile:
- Switch to release versions
- Use ftp(http) mirror
- Add PKG_LICENSE_FILES
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sat, 25 Jun 2022 14:41:18 +0000 (16:41 +0200)]
ethtool: update to 5.18
9eabf30 Release version 5.18.
2b3ddcb ethtool: fec: Change the prompt string to adapt to current situations
d660dde pretty: add missing message descriptions for rings
aaeb16a pretty: support u8 enumerated types
6b320b8 rings: add support to set/get cqe size
41fddc0 update UAPI header copies
42e6c28 help: fix alignment of rx-buf-len parameter
e1d0a19 ethtool.8: Fix typo in man page
37f0586 Release version 5.17.
8c2984c strset: do not put a pointer to a local variable to nlctx
8fd02a2 ioctl: add the memory free operation after send_ioctl call fails
b9f25ea ethtool: Add support for OSFP transceiver modules
6e79542 features: add --json support
5ed5ce5 Merge branch 'next' into master
b90abbb man: document recently added parameters
51a9312 tunables: add support to get/set tx copybreak buf size
a081c2a rings: add support to set/get rx buf len
d699bab Merge branch 'master' into next
52db6b9 Merge branch 'review/module-extstate' into next
6407b52 monitor: add option for --show-module/--set-module
1f35786 ethtool: Add transceiver module extended state
2d4c5b7 ethtool: Add ability to control transceiver modules' power mode
005908b Update UAPI header copies
Signed-off-by: Nick Hainke <vincent@systemli.org>
Eneas U de Queiroz [Tue, 21 Jun 2022 18:21:44 +0000 (15:21 -0300)]
wolfssl: disable AES-NI by default for x86_64
WolfSSL is crashing with an illegal opcode in some x86_64 CPUs that have
AES instructions but lack other extensions that are used by WolfSSL
when AES-NI is enabled.
Disable the option by default for now until the issue is properly fixed.
People can enable them in a custom build if they are sure it will work
for them.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Sander Vanheule [Sun, 26 Jun 2022 14:56:01 +0000 (16:56 +0200)]
firmware-utils: bump to git HEAD
Fixes the safeloader model identifiers for EAP225-Outdoor v1/v3 devices.
1e3d47292b2e tplink-safeloader: fix EAP225-Outdoor model IDs
9563fe8e78cb tplink-safeloader: add regionless EAP225-V3 IDs
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Felix Fietkau [Sun, 26 Jun 2022 09:47:12 +0000 (11:47 +0200)]
mac80211: increase airtime scheduler quantum
improves performance by requiring fewer iterations over tx queues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Markus Stockhausen [Sun, 26 Jun 2022 08:28:26 +0000 (10:28 +0200)]
realtek: cleanup LAG logging
Setting up DSA bond silently fails if mode is not 802.3ad. Add log message
to fix it. As we are already here harmonize all logging messages in the
add/delete functions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Felix Fietkau [Sat, 18 Jun 2022 08:52:09 +0000 (10:52 +0200)]
mac80211: add airtime fairness improvements
This reverts the airtime scheduler back from the virtual-time based scheduler
to the deficit round robin scheduler implementation.
This reduces burstiness and improves fairness by improving interaction with AQL.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Alexandru Gagniuc [Mon, 16 May 2022 02:54:47 +0000 (21:54 -0500)]
realtek: EnGenius EWS2910P: add support for SFP ports
The SFP cages 9F and 10F share the same SCL line. Currently, there
isn't a good way to model this. Thus, only one SFP port can be fully
supported.
Cage 10F is fully supported with an I2C bus and sfp handle. Linux
automatically handles enabling or disabling the TX laser.
Cage 9F is only parially supported, without the sfp handle. The SDA
line is hogged as an input, so that it remains high. SCL transitions
sould not affect modules connected to this cage. The default value of
the tx-disable line is high (active). It is exported as a gpio, but
the laser is off by default. To enable the laser:
echo 0 > /sys/class/gpio/sff-p9-tx-disable/value
Thus, both modules can be used for networking, but only 10F will be
able to detect and identify a plugged in SFP module.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Alexandru Gagniuc [Sat, 14 May 2022 06:34:04 +0000 (01:34 -0500)]
realtek: add support for EnGenius EWS2910P
Add support for the Engenius EWS2910P PoE switch. This is an RTL8380
based switch with two SFP slots, and PoE 802.3af one every RJ-45 port.
The specs say 802.3af, but the vendor firmware configures the PSE for
a budget of 31W, indicating 802.3at support.
Specifications:
---------------
* SoC: Realtek RTL8380M
* Flash: 32 MiB SPI flash Macronix MX25L25635E
* RAM: 256 MiB (As reported by bootloader)
* Ethernet: 16x 10/100/1000 Mbps with PoE
2x SFP slots
* Buttons: 1 "Reset" button on front panel
1 "LED mode: button on front panel
1 "On/Off" Toggle switch on the back
* Power: 48V-54V DC barrel jack
* UART: 1 serial header (JP1) with populated 2.54mm pitch header
Labeled GRTV for ground, rx, tx, and 3.3V respectively
* PoE: 1 STM ST32F100 microcontroller
2 BCM59111 PSE chips
Works:
------
- (8) RJ-45 ethernet ports
- Switch functions
- LEDs and buttons
Not yet enabled:
----------------
- SFP ports (will be enabled in a subsequent change)
- Power-over-Ethernet (requires realtek-poe package)
Install via web interface:
-------------------------
The factory firmware will accept and flash the initramfs image. It is
recommended to flash to "Partition 0". Flashing to "Partition 1" is
not supported at this point.
The factory web GUI will show the following warning:
" Warning: The firmware version is v0.00.00-c0.0.00
The firmware image you are uploading is older than the current
firmware of the switch. The device will reset back to default
settings. Are you sure you want to proceed?"
This is expected when flashing OpenWrt. After the initramfs image
boots, flash the -sysupgrade using either the commandline or LuCI.
Install via serial console/tftp:
--------------------------------
The u-boot firmware will not stop the boot, regardless of which key is
pressed. To access the u-boot console, ground out the CLK (pin 16) of
the ROM (U22) when u-boot is reading the linux image. If timed
correctly, the image CRC will fail, and u-boot will drop to a shell:
> rtk network on
> setenv ipaddr <address of tftp server>
> tftp $(freemem) <name-of-initramfs-image.bin>
> bootm
Then flash the -sysupgrade using either the commandline or luci.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[gpio-led node names, OpenWrt and LuCI capitalization in commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Semih Baskan [Tue, 21 Jun 2022 05:43:50 +0000 (08:43 +0300)]
ramips: add support for Asus RT-N12+ B1 and RT-N300 B1
Asus RT-N12+ B1 and Asus RT-N300 B1 are the same device
with a different name.
The OEM firmwares have the same MD5 with Asus RT-N11P B1.
Same instructions for Asus RT-N11P B1 see:
commit
c3dc52e39ac8 ("ramips: add support for Asus RT-N10P V3 / RT-N11P B1 / RT-N12 VP B1")
Signed-off-by: Semih Baskan <strstgs@gmail.com>
(Added id from the PR review to commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Chuncheng Chen [Tue, 14 Jun 2022 06:11:52 +0000 (14:11 +0800)]
ramips: add support for ASUS RT-AX53U
Specifications:
- Device: ASUS RT-AX53U
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 3 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- Ports: USB 3.0
- LEDs: 1x POWER (blue, configurable)
3x LAN (blue, configurable)
1x WAN (blue, configurable)
1x USB (blue, not configurable)
1x 2.4G (blue, not configurable)
1x 5G (blue, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
(replaced led label, added key-* prefix to buttons, added note about
BBT)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Chen Minqiang [Sat, 30 Apr 2022 15:28:29 +0000 (23:28 +0800)]
kexec-tools: add kdump scripts util
This add back kdump scripts to save crashlog or vmcore to disk
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Christian Lamparter [Fri, 24 Jun 2022 18:55:15 +0000 (20:55 +0200)]
apm821xx: WNDAP660: fix ethernet port ordering
Tim Small reported:
| Viewing the 'Network' -> 'Switch' config page in LuCI:
|
| The LuCI LAN 1 port corresponds to the port physically
| labelled 2 at the rear of the device.
| [...]
|
| When a patch cord is attached to the port labelled 1 [...],
| the LED labelled 2 illuminates. [...]
=> Ports, LuCI and LEDs are reversed/don't match.
Reported-by: Tim Small
Fixes: #10111
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Fri, 24 Jun 2022 17:30:50 +0000 (19:30 +0200)]
x86: fix damaged config 5.10 refresh
Restore CONFIG_I8K + CONFIG_INTEL_INT0002_VGPIO that got
removed when I refreshed the config. Each x86 target gets
its own CONFIG_CRYPTO_BLAKE2S + LIB settings as only the
x86_64 can use the accelerated x86 version.
Also remove two extra spaces that sneaked into geode's config.
Fixes: 539e60539a2f ("generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Clemens Hopfer [Sat, 28 May 2022 19:34:48 +0000 (21:34 +0200)]
octeon: add support for Ubiquiti UniFi Security Gateway
Ubiquiti UniFi Security Gateway (USG) is largely identical to
the EdgeRouter Lite (ERLite-3) apart from a different board ID
and two dome leds.
Device data (from WikiDev):
CPU: Cavium Octeon Plus CN5020 @500MHz 2-cores
Ethernet: 3x Atheros AR8035-A GbE PHY's
Flash: On-board 4MB Flash
Storage: Internal 3.8GB USB Flash (Kingston ID) drive
w/ 1.5GB free for use occupies single internal USB port.
Serial: 1x RJ45 port on front panel. 115200, 8N1
Buttons: 1x Reset
Flash instructions are identical to EdgeRouter Lite.
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Felix Fietkau [Fri, 24 Jun 2022 19:15:12 +0000 (21:15 +0200)]
mt76: update to the latest version
1696f9eb8b40 mt76: mt7915: do not copy ieee80211_ops pointer in mt7915_mmio_probe
a4db5869d660 mt76: mt7915: update mpdu density in 6g capability
500c18014d95 mt76: mt7915: add sta_rec with EXTRA_INFO_NEW for the first time only
3ef66fc7c714 mt76: do not check the ccmp pn for ONLY_MONITOR frame
dd682eead016 mt76: mt7915: update the maximum size of beacon offload
4fb991f2c997 mt76: mt7615: add sta_rec with EXTRA_INFO_NEW for the first time only
ba39ed3b44f1 mt76: mt76x02: improve reliability of the beacon hang check
fd8211cf7c59 mt76: mt7921: sync with updated patch
f2edd340ddb4 mt76: allow receiving frames with invalid CCMP PN via monitor interfaces
b6e865e2cc70 mt76: mt7615: fix throughput regression on DFS channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sebastian Schaper [Wed, 22 Jun 2022 21:38:26 +0000 (23:38 +0200)]
ath79: fix rootfs padding for D-Link DAP-2xxx
It was observed that `rootfs_data` was sometimes not correctly erased
after performing sysupgrade, resulting in previous settings to prevail.
Add call to `wrgg-pad-rootfs` in sysupgrade image recipe to ensure any
previous jffs2 will be wiped, consistent with DAP-2610 from the ipq40xx
target, which introduced the double-flashing procedure for these devices.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Tomasz Maciej Nowak [Mon, 20 Jun 2022 12:50:23 +0000 (14:50 +0200)]
mac80211: brcmfmac: allow setting MAC from NVMEM cells
The MAC can be stored in OTP memory or in flash memory, currently the
driver could read it only from OTP. Backport the patch allowing setting
the MAC address from flash. Some modules have the OTP programmed but
the ODM/OEM decided to overwrite it with value stored in flash.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tomasz Maciej Nowak [Mon, 20 Jun 2022 12:49:45 +0000 (14:49 +0200)]
generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e89 ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca93670693b ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tomasz Maciej Nowak [Mon, 20 Jun 2022 12:48:19 +0000 (14:48 +0200)]
kernel: clean-up after kernel 5.4 removal
These narrowments are no longer useful, since there's no lower version
than 5.10 supported in tree.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Nick Hainke [Tue, 7 Jun 2022 19:32:11 +0000 (21:32 +0200)]
nftables: update to 1.0.4
Needs libnftnl 1.2.2.
3eb0da9f build: Bump version to 1.0.4
a964d1b5 tests: shell: remove leftover modules on cleanup
818f7dde evaluate: reset ctx->set after set interval evaluation
3835de19 tests: shell: sets_with_ifnames release netns on exit
59bd944f optimize: segfault when releasing unsupported statement
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Tue, 7 Jun 2022 19:27:12 +0000 (21:27 +0200)]
libnftnl: update to 1.2.2
build: libnftnl 1.2.2 release
accee9a set_elem: missing export symbol
e2514c0 exthdr: tcp option reset support
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Wed, 1 Jun 2022 05:53:35 +0000 (07:53 +0200)]
nftables: clean up Makefile
Add PKG_LICENSE_FILES. Use SPDX.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Wed, 1 Jun 2022 05:43:13 +0000 (07:43 +0200)]
nftables: update to 1.0.3
Remove backport:
- 001-examples-compile-with-make-check.patch
87fdf683 build: Bump version to 1.0.3
c4ec825b nft: simplify chain lookup in do_list_chain
4f6724f1 intervals: fix compilation --with-mini-gmp
4c20fe95 json: update json output ordering to place rules after chains
57741350 netlink_delinearize: release last register on exit
d6fdb0d8 sets_with_ifnames: add test case for concatenated range
88b2345a segtree: add pretty-print support for wildcard strings in concatenated sets
806ab081 netlink: swap byteorder for host-endian concat data
c224aa6b intervals: deletion should adjust range not yet in the kernel
ea1f1c9f optimize: memleak in statement matrix
0a6dbfce optimize: merge nat rules with same selectors into map
743b0e81 optimize: do not clone unsupported statement
c8b35039 optimize: incorrect logic in verdict comparison
fc4da141 src: fix always-true assertions
d1289bff intervals: set on EXPR_F_KERNEL flag for new elements in set cache
721b9dec tests: add concat test case with integer base type subkey
22b750aa src: allow use of base integer types as set keys in concatenations
3ed9fada intervals: build list of elements to be added from cache
e45b4939 intervals: fix deletion of multiple ranges with automerge
3b7b22ae intervals: add elements with EXPR_F_KERNEL to purge list only
ea31855d netlink: remove unused argument from helper function
48204bd7 intervals: Simplify element sanity checks
ab1b21be intervals: unset EXPR_F_KERNEL for adjusted elements
e0beff27 src: restore interval sets work with string datatypes
3e8d934e intervals: support to partial deletion with automerge
7a6e1604 evaluate: allow for zero length ranges
3da9643f intervals: add support to automerge with kernel elements
7b061e63 mnl: update mnl_nft_setelem_del() to allow for more reuse
fdb8e0ff src: remove rbtree datastructure
81e36530 src: replace interval segment tree overlap and automerge
f1cc44ed src: add EXPR_F_KERNEL to identify expression in the kernel
ad43b84e segtree: add support for get element with sets that contain ifnames
06db2308 segtree: use correct byte order for 'element get'
4c6681a7 tests: add testcases for interface names in sets
5e393ea1 segtree: add string "range" reversal support
2fb4d7ea src: make interval sets work with string datatypes
403936c1 evaluate: string prefix expression must retain original length
ada50f84 segtree: split prefix and range creation to a helper function
ae7d32fc evaluate: keep prefix expression length
d2b23984 evaluate: make byteorder conversion on string base type a no-op
c36ecfc2 tests: py: Add meta time tests without 'meta' keyword
6fa4ff56 tests: py: Don't colorize output if stderr is redirected
f561a0cc tests: monitor: Hide temporary file names from error output
75fea8a5 tests: py: extend meta time coverage
4460b839 meta: fix compiler warning in date_type_parse()
02100978 meta: time: use uint64_t instead of time_t
4e0026dc include: add missing `#include`
ab74fb5b examples: add .gitignore file
bcad4761 tests: py: add inet/vmap tests
214494aa optimize: Restore optimization for raw payload expressions
82762ab6 src: allow to use integer type header fields via typeof set declaration
64bb3f43 src: allow to use typeof of raw expressions in set declaration
ff0f30e3 expression: typeof verdict needs verdict datatype
60f5c107 src: copy field_count for anonymous object maps as well
4cf97abf rule: Avoid segfault with anonymous chains
4e718641 evaluate: init cmd pointer for new on-stack context
1ea71c23 optimize: do not assume log prefix
3f36cc6c optimize: do not merge unsupported statement expressions
19960c8d optimize: incorrect assert() for unexpected expression type
3de1dbd2 optimize: more robust statement merge with vmap
99eb4696 optimize: fix vmap with anonymous sets
e8f0fa21 scanner: Fix for ipportmap nat statements
59d184be scanner: dup, fwd, tproxy: Move to own scopes
069a0450 scanner: meta: Move to own scope
2165324d scanner: at: Move to own scope
a67fce7f scanner: nat: Move to own scope
578467c1 scanner: policy: move to own scope
a1669709 scanner: flags: move to own scope
020372d9 scanner: reject: Move to own scope
543bf3c2 scanner: import, export: Move to own scopes
88105810 scanner: reset: move to own Scope
8a7e430a scanner: monitor: Move to own Scope
e5547017 scanner: rt: Extend scope over rt0, rt2 and srh
04c95f14 scanner: type: Move to own scope
62a95698 scanner: dst, frag, hbh, mh: Move to own scopes
a060d912 scanner: ah, esp: Move to own scopes
4e215fdf scanner: osf: Move to own scope
5166b298 scanner: dccp, th: Move to own scopes
3e04a6e2 scanner: udp{,lite}: Move to own scope
bbdcfbfa scanner: comp: Move to own scope.
232f2c32 scanner: synproxy: Move to own scope
26b53653 scanner: tcp: Move to own scope
f5722119 scanner: igmp: Move to own scope
a7d8cca9 scanner: icmp{,v6}: Move to own scope
5d837d27 src: add tcp option reset support
1d507ce7 build: explicitly pass --version-script to linker
e98a9b83 libnftables.map: export new nft_ctx_{get,set}_optimize API
9eb98b3b tests: add test case for flowtable with owner flag
18a08fb7 examples: compile with `make check' and add AM_CPPFLAGS
Signed-off-by: Nick Hainke <vincent@systemli.org>
Tomasz Maciej Nowak [Tue, 7 Jun 2022 13:58:32 +0000 (15:58 +0200)]
ath79: bsap18x0: specify FIS directory location in dts
The redboot-fis parser has option to specify the location of FIS
directory, use that, instead of patching the parser to scan for it, and
specifying location in kernel config.
Tested-by: Brian Gonyer <bgonyer@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tomasz Maciej Nowak [Tue, 7 Jun 2022 13:58:31 +0000 (15:58 +0200)]
treewide: use upstream compatible for RedBoot FIS parser
No reason to keep that around, since upstream one does the same.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tomasz Maciej Nowak [Tue, 7 Jun 2022 13:58:30 +0000 (15:58 +0200)]
ath79: bsap18x0: pad rootfs image
This image is supposed to be written with help of bootloader to the
flash, but as it stands, it's not aligned to block size and RedBoot will
happily create non-aligned partition size in FIS directory. This could
lead to kernel to mark the partition as read-only, therefore pad the
image to block erase size boundary.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tomasz Maciej Nowak [Tue, 7 Jun 2022 13:58:29 +0000 (15:58 +0200)]
ath79: ja76pf2: use nvmem cells to specify MAC addresses
The bootloader on this board hid the partition containig MAC addresses
and prevented adding this space to FIS directory, therefore those had to
be stored in RedBoot configuration as aliases to be able to assigne them
to proper interfaces. Now that fixed partition size are used instead of
redboot-fis parser, the partition containig MAC addresses could be
specified, and with marking it as nvmem cell, we can assign them without
userspace involvement.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tomasz Maciej Nowak [Tue, 7 Jun 2022 13:58:28 +0000 (15:58 +0200)]
ath79: move image check for devices with RedBoot
Don't comence the switch to RAMFS when the image format is wrong. This
led to rebooting the device, which could lead to false impression that
upgrade succeded.
Being here, factor out the code responsible for upgrading RedBoot
devices to separate file.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tomasz Maciej Nowak [Tue, 7 Jun 2022 13:58:27 +0000 (15:58 +0200)]
ath79: switch some RedBoot based devices to OKLI loader
After the kernel has switched version to 5.10, JA76PF2 and
RouterStations lost the capability to sysupgrade the OpenWrt version.
The cause is the lack of porting the patches responsible for partial
flash erase block writing and these boards FIS directory and RedBoot
config partitions share the same erase block. Because of that the FIS
directory can't be updated to accommodate kernel/rootfs partition size
changes. This could be remedied by bootloader update, but it is very
intrusive and could potentially lead to non-trivial recovery procedure,
if something went wrong. The less difficult option is to use OpenWrt
kernel loader, which will let us use static partition sizes and employ
mtd splitter to dynamically adjust kernel and rootfs partition sizes.
On sysupgrade from ath79 19.07 or 21.02 image, which still let to modify
FIS directory, the loader will be written to kernel partition, while the
kernel+rootfs to rootfs partition.
The caveats are:
* image format changes, no possible upgrade from ar71xx target images
* downgrade to any older OpenWrt version will require TFTP recovery or
usage of bootloader command line interface
To downgrade to 19.07 or 21.02, or to upgrade if one is already on
OpenWrt with kernel 5.10, for RouterStations use TFTP recovery
procedure. For JA76PF2 use instructions from this commit message:
commit
0cc87b3bacee ("ath79: image: disable sysupgrade images for routerstations and ja76pf2"),
replacing kernel image with loader (loader.bin suffix) and rootfs
image with firmware (firmware.bin suffix).
Fixes: b10d6044599d ("kernel: add linux 5.10 support")
Fixes: 15aa53d7ee65 ("ath79: switch to Kernel 5.10")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(mkubntimage was moved to generic-ubnt.mk)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tomasz Maciej Nowak [Tue, 7 Jun 2022 13:58:26 +0000 (15:58 +0200)]
ath79: jj76pf2: enable TCN75 sensor
This SBC has Microchip TCN75 sensor, wich measures ambient temperature.
Specify it in dts to allow readout by applications using kernel hwmon
API.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Mark Mentovai [Thu, 9 Jun 2022 15:00:58 +0000 (11:00 -0400)]
include/prereq-build.mk: macOS cross build improvements
This updates prereq-build.mk to find a suitable realpath utility, and
adds another place to look for a suitable getopt utility.
realpath has been used most notably by scripts/ipkg-build since
commit
bb95be9265a9 ("scripts,ipkg-build: use realpath for pkg_dir")
and there are assorted other uses of it during a build.
It is ordinarily provided by GNU coreutils. This adds a SetupHostCommand
to locate it either under its own name or under grealpath, the name that
it will be available as under MacPorts or Homebrew, which use
--program-prefix=g.
Similarly, update the SetupHostCommand for getopt to be able to locate a
util-linux getopt at the default path used by MacPorts, in the same
fashion that
commit
cc16f5d73e77 ("build: try to find getopt in macOS homebrew's standard location")'
did for Homebrew. As there is no standard alternative --program-prefix
for util-linux utilities in the way that GNU packages often use a "g"
prefix, this path-based approach is required in case a non-util-linux
getopt (such as one provided by an OS) shadows the util-linux getopt
in the PATH.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Alexey Smirnov [Mon, 4 Apr 2022 08:59:25 +0000 (11:59 +0300)]
omap: enable 5.15 as testing kernel
Compiled for and run-tested on BBB
Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
Alexey Smirnov [Mon, 4 Apr 2022 08:58:48 +0000 (11:58 +0300)]
omap: update config for 5.15
This was done by executing make kernel_oldconfig
Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
Alexey Smirnov [Mon, 4 Apr 2022 08:06:27 +0000 (11:06 +0300)]
omap: copy config from 5.10 to 5.15
copy config from 5.10 to 5.15
Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
Stefan Kalscheuer [Thu, 19 May 2022 19:10:34 +0000 (21:10 +0200)]
kernel: add kmod-leds-turris-omnia
Add support for LEDs of the CZ.NIC Turris Omnia using the upstream
driver.
There is no generic way to control the LEDs in UCI manner, however
the kernel module is the first step to actually use the RGB LEDs in
custom logic.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
(removed DMARC notice, added driver to Turris Omnia, moved module
recipe to target/linux/mvebu/modules.mk)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Bjørn Mork [Fri, 29 Apr 2022 14:38:27 +0000 (16:38 +0200)]
ramips: force ZyXEL NR7101 to boot from "Kernel" partition
Make sure BootingFlag points to the system partition we install to.
The BootingFlag variable selects which system partition the system
boots from (0 => "Kernel", 1 => "Kernel2"). OpenWrt does not yet have
device specific support for this dual image scheme, and can therefore
only boot from "Kernel".
This has not been an issue until now, since all known OEM firmware
versions have ignored "Kernel2" - leaving the BootingFlag fixed at 0.
But the newest OEM firmware has a new upgrade procedure, installing
to the "inactive" system partition and setting BootingFlag accordingly.
This workaround is needed until the dual image scheme is fully
supported.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Arınç ÜNAL [Thu, 17 Mar 2022 13:10:08 +0000 (16:10 +0300)]
ramips: mt7621-dts: fix claiming rgmii2 pin group for EdgeRouter X SFP
For a TX->TX connected external phy to transmit/receive data, the rgmii2
pin group needs to be claimed with gpio function, at least for EdgeRouter X
SFP. We already claim the pin group under the pinctrl node with gpio
function on the gpio node on mt7621_ubnt_edgerouter-x.dtsi.
However, we should claim a pin group under its consumer node. It's the
ethernet node in this case, which we already claim the rgmii2 pin group
under it on mt7621.dtsi. Therefore, set the function as gpio on the rgmii2
node for EdgeRouter X SFP and get rid of claiming the rgmii2 pin group
under the pinctrl node. With this change, we also get to remove a
definition from mt7621_ubnt_edgerouter-x.dtsi which is specific to
EdgeRouter X SFP.
This change is tested on an EdgeRouter X SFP.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Rafał Miłecki [Fri, 24 Jun 2022 07:09:02 +0000 (09:09 +0200)]
bcm53xx: copy patch disabling GRO to kernel 5.15
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Fri, 10 Jun 2022 08:51:23 +0000 (10:51 +0200)]
bcm53xx: enable & setup packet steering
Packet steering can improve NAT masquarade performance on Northstar by
40-50%. It makes reaching 940-942 Mb/s possible on BCM4708 (and
obviously BCM47094 too). Add scripts setting up the most optimal
Northstar setup.
Below are testing results for running iperf TCP traffic from LAN to WAN.
They were used to pick up golden values.
┌──────────┬──────────┬────────────────────┬────────────────────┐
│ eth0 │ br-lan │ flow_offloading=0 │ flow_offloading=1 │
│ │ ├─────────┬──────────┼─────────┬──────────┤
│ rps_cpus │ rps_cpus │ BCM4708 │ BCM47094 │ BCM4708 │ BCM47094 │
├──────────┼──────────┼─────────┼──────────┼─────────┼──────────┤
│ 0 │ 0 │ 387 │ 671 │ 707 │ 941 │
│ 0 │ 1 │ 343 │ 576 │ 705 │ 941 │
│ 0 │ 2 │ ✓ 574 │ ✓ 941 │ 704 │ 940 │
│ 1 │ 0 │ 320 │ 549 │ 561 │ 941 │
│ 1 │ 1 │ 327 │ 551 │ 553 │ 941 │
│ 1 │ 2 │ 523 │ ✓ 940 │ 559 │ 940 │
│ 2 │ 0 │ 383 │ 652 │ ✓ 940 │ 941 │
│ 2 │ 1 │ 448 │ 754 │ ✓ 942 │ 941 │
│ 2 │ 2 │ 404 │ 655 │ ✓ 941 │ 941 │
└──────────┴──────────┴─────────┴──────────┴─────────┴──────────┘
Above tests were performed with all eth0 interrupts handled by CPU0.
Setting "echo 2 > /proc/irq/38/smp_affinity" was tested on BCM4708 but
it didn't increased speeds (just required different steering):
┌──────────┬──────────┬───────────┐
│ eth0 │ br-lan │ flow_offl │
│ rx-0 │ rx-0 │ oading=0 │
│ rps_cpus │ rps_cpus │ BCM4708 │
├──────────┼──────────┼───────────┤
│ 0 │ 0 │ 384 │
│ 0 │ 1 │ ✓ 574 │
│ 0 │ 2 │ 348 │
│ 1 │ 0 │ 383 │
│ 1 │ 1 │ 412 │
│ 1 │ 2 │ 448 │
│ 2 │ 0 │ 321 │
│ 2 │ 1 │ 520 │
│ 2 │ 2 │ 327 │
└──────────┴──────────┴───────────┘
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Mon, 20 Jun 2022 08:21:20 +0000 (10:21 +0200)]
bcm53xx: disable GRO by default at kernel level
This improves NAT masquarade network performance.
An alternative to kernel change would be runtime setup but that requires
ethtool and identifying relevant network interface and all related
switch ports interfaces.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Bjørn Mork [Sun, 19 Jun 2022 13:59:27 +0000 (15:59 +0200)]
realtek: fix gcc-12 build with -Werror=array-compare
Removing this gcc-12 error:
arch/mips/rtl838x/setup.c:64:30: error: comparison between two arrays [-Werror=array-compare]
64 | else if (__dtb_start != __dtb_end)
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Andreas Böhler [Sun, 19 Jun 2022 17:53:12 +0000 (19:53 +0200)]
realtek: make "u-boot-env" partition writable for Netgear 3xx series
The Netgear GS3xx devices do not properly initialise the port LEDs during
startup unless the boot command in U-Boot is changed. Making the U-Boot
env partition writable allows this modification to be done from within
OpenWrt by calling "fw_setenv bootcmd rtk network on\; boota".
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Stijn Segers [Sun, 19 Jun 2022 17:55:28 +0000 (19:55 +0200)]
realtek: make Netgear GS1xx u-boot env partition writable
Make the u-boot environment partition for the NETGEAR
GS108T v3 and GS110TPP writable (they share a DTS), so
the values can be manipulated from userspace.
See https://forum.openwrt.org/t/57875/1567 for a real
world example.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Paul Maruhn [Tue, 22 Mar 2022 20:06:42 +0000 (21:06 +0100)]
ath79: support for TP-Link EAP225-Outdoor v3
This model is almost identical to the EAP225-Outdoor v1.
Major difference is the RTL8211FS PHY Chipset.
Device specifications:
* SoC: QCA9563 @ 775MHz
* Memory: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 2x2
* Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO
* Ethernet (RTL8211FS): 1× 1GbE, PoE
Flashing instructions:
* ssh into target device with recent (>= v1.6.0) firmware
* run `cliclientd stopcs` on target device
* upload factory image via web interface
Debricking:
To recover the device, you need access to the serial port. This requires
fine soldering to test points, or the use of probe pins.
* Open the case and solder wires to the test points: RXD, TXD and TPGND4
* Use a 3.3V UART, 115200 baud, 8n1
* Interrupt bootloader by holding ctrl+B during boot
* upload initramfs via built-in tftp client and perform sysupgrade
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From stock ifconfig:
ath0 Link encap:Ethernet HWaddr D8:...:2E
ath10 Link encap:Ethernet HWaddr D8:...:2F
br0 Link encap:Ethernet HWaddr D8:...:2E
eth0 Link encap:Ethernet HWaddr D8:...:2E
Signed-off-by: Paul Maruhn <paulmaruhn@posteo.de>
Co-developed-by: Philipp Rothmann <philipprothmann@posteo.de>
Signed-off-by: Philipp Rothmann <philipprothmann@posteo.de>
[Add pre-calibraton nvme-cells]
Tested-by: Tido Klaassen <tido_ff@4gh.eu>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Philipp Rothmann [Tue, 21 Jun 2022 19:39:39 +0000 (21:39 +0200)]
ath79: generic: add support for Realtek PHY
Some models of the TP-Link EAP225 series use a Realtek PHY,
therefore the driver is added.
Signed-off-by: Philipp Rothmann <philipprothmann@posteo.de>
Felix Fietkau [Tue, 21 Jun 2022 18:55:24 +0000 (20:55 +0200)]
mt76: update to the latest version
4554ee652caf mt76: mt7921: fix warning Using plain integer as NULL pointer
a3f1d6ccf3ca mt76: mt7921: add missing bh-disable around rx napi schedule
9aeca2a5ce47 mt76: mt7921: get rid of mt7921_mcu_exit
fee8a5911c76 mt76: connac: move shared fw structures in connac module
db4d784ae7ba mt76: mt7921: move fw toggle in mt7921_load_firmware
16ab6bf49556 mt76: connac: move mt76_connac2_load_ram in connac module
29fd748801c6 mt76: connac: move mt76_connac2_load_patch in connac module
051c68d18214 mt76: mt7663: rely on mt76_connac2_fw_trailer
d6ae3505ac6c mt76: enable the VHT extended NSS BW feature
488a5ccc9762 mt76: mt7921: rely on mt76_dev in mt7921_mac_write_txwi signature
934029bb93e2 mt76: mt7915: rely on mt76_dev in mt7915_mac_write_txwi signature
ecefae4c7d72 mt76: connac: move mac connac2 defs in mt76_connac2_mac.h
b5eecc841df8 mt76: connac: move connac2_mac_write_txwi in mt76_connac module
012e619a07b9 mt76: connac: move mt76_connac2_mac_add_txs_skb in connac module
1b492be795ea mt76: mt7921: not support beacon offload disable command
f1f46d3b4b19 mt76: mt7921: fix command timeout in AP stop period
cae61112ef1d mt76: connac: move HE radiotap parsing in connac module
487674062643 mt76: connac: move mt76_connac2_reverse_frag0_hdr_trans in mt76-connac module
649bdc4983c4 mt76: connac: move mt76_connac2_mac_fill_rx_rate in connac module
cb75aaa39252 mt76: mt7921s: remove unnecessary goto in mt7921s_mcu_drv_pmctrl
e0eaf66eaebb mt76: mt7615: do not update pm stats in case of error
f8d125b4ea30 mt76: mt7921: do not update pm states in case of error
6329a834907e mt76: mt7921s: fix possible sdio deadlock in command fail
8a04f1b04662 mt76: mt7921: fix aggregation subframes setting to HE max
e52283439094 mt76: mt7915: disable UL MU-MIMO for mt7915
fd3958970e3d mt76: mt7921: enlarge maximum VHT MPDU length to 11454
18df38fe77f7 mt76: mt7915: get rid of unnecessary new line in mt7915_mac_write_txwi
149e95f5d7a6 mt76: connac: move mt76_connac_fw_txp in common module
899d192e8a79 mt76: move mt7615_txp_ptr in mt76_connac module
7184f0a6f6a5 mt76: connac: move mt76_connac_tx_free in shared code
c42d45278fa5 mt76: connac: move mt76_connac_tx_complete_skb in shared code
0993f4ef96f8 mt76: connac: move mt76_connac_write_hw_txp in shared code
467960fab791 mt76: connac: move mt7615_txp_skb_unmap in common code
2e758064b085 mt76: mt7915: rely on mt76_connac_tx_free
2065a7901671 mt76: move mcu_txd/mcu_rxd structures in shared code
576c1b7c472b mt76: move mt76_connac2_mcu_fill_message in mt76_connac module
7275f7758090 mt76: mt7915: fix incorrect testmode ipg on band 1 caused by wmm_idx
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Kevin Darbyshire-Bryant [Tue, 21 Jun 2022 13:15:40 +0000 (14:15 +0100)]
kernel: filter -no-plt from KCFLAGS
Compiler option -no-plt will break kernel builds on some architectures
eg. (x86) Filter this option from the recently introduced handling of
KCFLAGS vs EXTRA_OPTIMISATION
Fixes: 1d42af720c6b ("kernel: use KCFLAGS for passing EXTRA_OPTIMIZATION flags")
Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Stijn Tintel [Mon, 9 May 2022 11:55:42 +0000 (14:55 +0300)]
hostapd: document ubus methods
Document the ubus methods we added to hostapd so that people don't have
to read code to figure out which methods are available and what they do.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Florian Fainelli [Tue, 14 Dec 2021 20:27:43 +0000 (12:27 -0800)]
bcm47xx: Fix Netgear WNR3500L v2 image format
CFE on these devices expects to find the kernel compressed with LZMA but
with no dictionnary and no loader, adjust the image generation
accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Wed, 22 Dec 2021 20:45:52 +0000 (12:45 -0800)]
bcm47xx: Updated devices database for Netgear WNR3500L V2
Update the device databases to contain an entry for the Netgear WNR3500L
v2 router, the same buttons and LEDs mapping as v1 is used.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Thu, 23 Dec 2021 03:25:14 +0000 (19:25 -0800)]
bcm47xx: Add support for brcmnand controller on BCMA bus
Back port the patches being submitted upstream in order to make the NAND
controller work on BCM47187/5358. This is a prerequisite for supporting
devices like the Netgear WNR3500L V2.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Wed, 22 Dec 2021 22:26:02 +0000 (14:26 -0800)]
broadcom-wl: Fix compilation with kernel 5.10
This adds a few fixes for compiling against Linux 5.10:
1. segment_eq() has been removed with upstream commit
428e2976a5bf7e7f5554286d7a5a33b8147b106a ("uaccess: remove
segment_eq") and can use uaccess_kernel() instead
2. ioremap_nocache() is removed and is now an alias for ioremap() with
upstream commit
4bdc0d676a643140bdf17dbf7eafedee3d496a3c ("remove
ioremap_nocache and devm_ioremap_nocache")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Rafał Miłecki [Wed, 15 Jun 2022 10:36:37 +0000 (12:36 +0200)]
kernel: drop patch adding hardcoded kernel compilation flags
1. KCFLAGS should be used for custom flags
2. Optimization flags are arch / SoC specific
3. -fno-reorder-blocks may *worsen* network performace on some SoCs
4. Usage of flags was *reversed* since 5.4 and noone reported that
If we really need custom flags then CONFIG_KERNEL_CFLAGS should get
default value adjusted properly (per target).
Ref:
4e0c54bc5bc8 ("kernel: add support for kernel 5.4")
Link: http://lists.openwrt.org/pipermail/openwrt-devel/2022-June/038853.html
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20190409093046.13401-1-zajec5@gmail.com/
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Rafał Miłecki [Wed, 15 Jun 2022 10:36:36 +0000 (12:36 +0200)]
kernel: support setting extra CFLAGS for kernel compilation
They may be used e.g. to optimize kernel size or performance.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Martin Blumenstingl [Mon, 20 Jun 2022 17:25:47 +0000 (19:25 +0200)]
lantiq: dts: fix reset controller reference on Danube and AR9
ar9.dtsi and danube.dtsi only have one reset controller and they are
naming it "reset". This is equivalent to "reset0" in vr9.dtsi. Fix the
references to the reset controller in the recently added PCI controller
reset line.
Fixes: 087f2cba26faf0 ("lantiq: dts: Add the reset line for the PCI controller")
Reported-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Piotr Dymacz [Mon, 23 May 2022 15:50:19 +0000 (17:50 +0200)]
ramips: fix booting on ZyXEL NBG-419N v2
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of other devices from 'ramips' target.
Fixes: #9842
Fixes: #8964
Reported-by: Juergen Hench <jurgen.hench@gmail.com>
Tested-by: Juergen Hench <jurgen.hench@gmail.com>
Signed-off-by: Demetris Ierokipides <ierokipides.dem@gmail.com>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Rafał Miłecki [Wed, 15 Jun 2022 08:41:37 +0000 (10:41 +0200)]
kernel: use KCFLAGS for passing EXTRA_OPTIMIZATION flags
This uses kernel's generic variable and doesn't require patching it with
a custom Makefile change. It's expected *not* to change any behaviour.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Sun, 19 Jun 2022 20:03:28 +0000 (22:03 +0200)]
kernel: backport mtd parser for Sercomm partitions
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Alin Nastac [Wed, 8 Jun 2022 09:58:00 +0000 (11:58 +0200)]
464xlat: delete SNATed conntracks on interface teardown
Existing conntracks will continue to be SNATed to 192.0.0.1 even after
464xlat interface gets teared down. To prevent this, matching
conntracks must be killed.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Logan Blyth [Wed, 8 Jun 2022 01:46:22 +0000 (21:46 -0400)]
mvebu: add SolidRun ClearFog GT 8K
ClearFog GT 8K is device sold by SolidRun. It is marketed as a
development board, not a consumer product. The device tree file for this board
is upstream in kernel.org.
Signed-off-by: Logan Blyth <mrbojangles3@gmail.com>
Christian Lamparter [Fri, 17 Jun 2022 14:10:16 +0000 (16:10 +0200)]
apm821xx: align gpio-keys node names with dt-schema
As per the series:
<https://www.spinics.net/lists/devicetree/msg508906.html>
"Enforce specific naming pattern for children (keys) to narrow the
pattern thus do not match other properties. This will require all
children to be properly prefixed or suffixed (button, event, switch
or key)."
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Mark Mentovai [Mon, 6 Jun 2022 04:59:14 +0000 (00:59 -0400)]
failsafe: run on all consoles listed in /proc/cmdline
On x86, when both CONFIG_GRUB_CONSOLE and CONFIG_GRUB_SERIAL are set (as
they are by default), the kernel command line will have two console=
entries, such as
console=tty0 console=ttyS0,115200n8
Failsafe was only running a shell on the first defined console, the VGA
console. This is a problem for devices like apu2, where there is only a
serial console and it appears on ttyS0.
Moreover, the console prompt to enter failsafe during boot was delivered
to, and its input read from, the last console= on the kernel command
line. So while the failsafe shell was on the first defined console, only
the last defined console could be used to enter failsafe during boot.
In contrast, the x86 bootloader (GRUB) operates on both the serial
console and the VGA console by virtue of "terminal_{input,output}
console serial". GRUB also provided an alternate means to enter failsafe
from either console. The presence of two console= kernel command line
parameters causes kernel messages to be delivered to both. Under normal
operation (not failsafe), procd runs login in accordance with inittab,
which on x86 specifies ttyS0, hvc0, and tty1, allowing login through any
of serial, hypervisor, or VGA console. Thus, serial access was
consistently available on x86 devices with serial consoles under normal
operation, except for shell access in failsafe mode (without editing the
kernel command line).
By presenting the failsafe prompt, reading failsafe prompt input, and
running failsafe shells on all consoles listed in /proc/cmdline,
failsafe mode will work correctly on devices with a serial console (like
apu2), and the same image without any need for reconfiguration can be
shared by devices with the more traditional (for x86) VGA console. This
improvement should benefit any system with multiple console= arguments,
including x86 and bcm27xx (Raspberry Pi).
Signed-off-by: Mark Mentovai <mark at moxienet.com>
Leo Soares [Thu, 16 Jun 2022 22:25:39 +0000 (23:25 +0100)]
libusb: fix missing link
adds `libusb-1.0.so` link on the target root again.
Fixes: 43539a6aabbe ("libusb: make InstallDev explicit")
Signed-off-by: Leo Soares <leo@hyper.ag>
(added fixed tag, reworded commit)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Martin Blumenstingl [Thu, 16 Jun 2022 19:43:48 +0000 (21:43 +0200)]
lantiq: dts: Add the reset line for the PCI controller
The PCI controller has it's reset line wired up to bit 13 of RCU.
Describe this in our .dtsi files.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Zhijun You [Thu, 16 Jun 2022 07:07:07 +0000 (15:07 +0800)]
ath10k: backport encapsulation offload support
This backports encap offload support from upstream.
On some ath10k devices there can be about 10% improvement on tx throughput.
Users can turn it on by setting frame_mode=2.
Signed-off-by: Zhijun You <hujy652@gmail.com>
Chris Blake [Sun, 12 Jun 2022 19:47:43 +0000 (14:47 -0500)]
ath79: add support for Netgear PGZNG1
This adds support for the Netgear PGZNG1, also known as the ADT Pulse
Gateway.
Hardware:
CPU: Atheros AR9344
Memory: 256MB
Storage: 256MB NAND Hynix H27U2G8F2CTR-BC
USB: 1x USB 2.0
Ethernet: 2x 100Mb/s
WiFi: Atheros AR9340 2.4GHz 2T2R
Leds: 8 LEDs
Button: 1x Reset Button
UART:
Header marked JPE1. Pinout is VCC, TX, RX, GND. The marked pin, closest
to the JPE1 marking, is VCC. Note VCC isn't required to be connected
for UART to work.
Enable Stock Firmware Shell Access:
1. Interrupt u-boot and run the following commands
setenv console_mode 1
saveenv
reset
This will enable a UART shell in the firmware. You can then login using
the root password of `icontrol`. If that doesn't work, the device is
running a firmware based on OpenWRT where you can drop into failsafe to
mount the FS and then modify /etc/passwd.
Installation Instructions:
1. Interupt u-boot and run the following commands
setenv active_image 0
setenv stock_bootcmd nboot 0x81000000 0 \${kernel_offset}
setenv openwrt_bootcmd nboot 0x82000000 0 \${kernel_offset}
setenv bootcmd run openwrt_bootcmd
saveenv
2. boot initramfs image via TFTP u-boot
tftpboot 0x82000000 openwrt-ath79-nand-netgear_pgzng1-initramfs-kernel.bin; bootm 0x82000000
3. Once booted, use LuCI sysupgrade to
flash openwrt-ath79-nand-netgear_pgzng1-squashfs-sysupgrade.bin
MAC Table:
WAN (eth0): xx:xa - caldata 0x0
LAN (eth1): xx:xb - caldata 0x6
WLAN (phy0): xx:xc - burned into ath9k caldata
Not Working:
Z-Wave
RS422
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
(added more hw-info, fixed file permissions)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Chris Blake [Tue, 15 Feb 2022 00:55:32 +0000 (18:55 -0600)]
kernel: add kmod-leds-pca955x
This patch adds support for the mainline kernel module for the PCA955x
LED driver. Note this requires i2c and GPIO support. Also worth calling
out this driver also enables GPIO support, depending on device tree
configuration.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Chris Blake [Tue, 15 Feb 2022 00:54:02 +0000 (18:54 -0600)]
kernel: add upstream patches for pca955x led driver
These patches are to support the pca955x led with OpenWRT correctly via
device tree on linux 5.10. Without these, the new LED function/color/reg
features can not be used.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Josef Schlehofer [Mon, 6 Jun 2022 19:55:13 +0000 (21:55 +0200)]
uboot-rockchip: drop CONFIG_IDENT_STRING
This row is no longer necessary as it was replaced by LOCALVERSION in
uboot.mk, which explicitly sets OpenWrt version to all U-boot packages accross
OpenWrt. [1]
[1] https://github.com/openwrt/openwrt/commit/
d6aa9d9e071d9f23ed26f5142991bc66aefe20f5
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Josef Schlehofer [Mon, 6 Jun 2022 20:08:42 +0000 (22:08 +0200)]
tools/libressl: update to version 3.4.3
Release notes:
https://ftp.openbsd.org/pub/OpenBSD/LibreSSL/libressl-3.4.3-relnotes.txt
```
It includes the following security fix:
* A malicious certificate can cause an infinite loop.
Reported by and fix from Tavis Ormandy and David Benjamin, Google.
```
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
projects / openwrt / openwrt.git / log