Lyude Paul [Tue, 26 Jun 2018 01:09:07 +0000 (21:09 -0400)]
drm/amdgpu: Dynamically probe for ATIF handle (v2)
The other day I was testing one of the HP laptops at my office with an
i915/amdgpu hybrid setup and noticed that hotplugging was non-functional
on almost all of the display outputs. I eventually discovered that all
of the external outputs were connected to the amdgpu device instead of
i915, and that the hotplugs weren't being detected so long as the GPU
was in runtime suspend. After some talking with folks at AMD, I learned
that amdgpu is actually supposed to support hotplug detection in runtime
suspend so long as the OEM has implemented it properly in the firmware.
On this HP ZBook 15 G4 (the machine in question), amdgpu wasn't managing
to find the ATIF handle at all despite the fact that I could see acpi
events being sent in response to any hotplugging. After going through
dumps of the firmware, I discovered that this machine did in fact
support ATIF, but that it's ATIF method lived in an entirely different
namespace than this device's handle (the device handle was
\_SB_.PCI0.PEG0.PEGP, but ATIF lives in ATPX's handle at
\_SB_.PCI0.GFX0).
So, fix this by probing ATPX's ACPI parent's namespace if we can't find
ATIF elsewhere, along with storing a pointer to the proper handle to use
for ATIF and using that instead of the device's handle.
This fixes HPD detection while in runtime suspend for this ZBook!
v2: Update the comment to reflect how the namespaces are arranged
based on the system configuration. (Alex)
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Lyude Paul [Tue, 26 Jun 2018 01:09:06 +0000 (21:09 -0400)]
drm/amdgpu: Add amdgpu_atpx_get_dhandle()
Since it seems that some vendors are storing the ATIF ACPI methods under
the same handle that ATPX lives under instead of the device's own
handle, we're going to need to be able to retrieve this handle later so
we can probe for ATIF there.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Lyude Paul [Tue, 26 Jun 2018 01:09:04 +0000 (21:09 -0400)]
drm/amdgpu: Make struct amdgpu_atif private to amdgpu_acpi.c
Currently, there is nothing in amdgpu that actually uses these structs
other than amdgpu_acpi.c. Additionally, since we're about to start
saving the correct ACPI handle to use for calling ATIF in this struct
this saves us from having to handle making sure that the acpi_handle
(and by proxy, the type definition for acpi_handle and all of the other
acpi headers) doesn't need to be included within the amdgpu_drv struct
itself. This follows the example set by amdgpu_atpx_handler.c.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Evan Quan [Mon, 11 Jun 2018 07:20:39 +0000 (15:20 +0800)]
drm/amd/powerplay: smc_dpm_info structure change
A new member Vr2_I2C_address is added.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Evan Quan [Mon, 28 May 2018 00:59:16 +0000 (08:59 +0800)]
drm/amd/powerplay: correct vega12 bootup values settings
The vbios firmware structure changed between v3_1 and v3_2. So,
the code to setup bootup values needs different paths based
on header version.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Evan Quan [Mon, 11 Jun 2018 08:46:40 +0000 (16:46 +0800)]
drm/amd/powerplay: correct vega12 thermal support as true
Thermal support is enabled on vega12.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Shirish S [Tue, 26 Jun 2018 04:02:39 +0000 (09:32 +0530)]
drm/amd/display: release spinlock before committing updates to stream
Currently, amdgpu_do_flip() spinlocks crtc->dev->event_lock and
releases it only after committing updates to the stream.
dc_commit_updates_for_stream() should be moved out of
spinlock for the below reasons:
1. event_lock is supposed to protect access to acrct->pflip_status _only_
2. dc_commit_updates_for_stream() has potential sleep's
and also its not appropriate to be in an atomic state
for such long sequences of code.
Signed-off-by: Shirish S <shirish.s@amd.com>
Suggested-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
James Zhu [Tue, 19 Jun 2018 17:44:04 +0000 (13:44 -0400)]
drm/amdgpu:Support new VCN FW version naming convention
Support new VCN FW version naming convention:
[31, 28] for VEP interface major version if applicable
[27, 24] for decode interface major version
[23, 20] for encode interface major version
[19, 12] for encode interface minor version
[11, 0] for firmware revision
Bit 20-23, it is encode major and non-zero for new naming convention.
This field is part of version minor and DRM_DISABLED_FLAG in old naming
convention. Since the latest version minor is 0x5B and DRM_DISABLED_FLAG
is zero in old naming convention, this field is always zero so far.
These four bits are used to tell which naming convention is present.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Fang, Peter <Peter.Fang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leo Liu [Mon, 25 Jun 2018 18:56:06 +0000 (14:56 -0400)]
drm/amdgpu: fix UBSAN: Undefined behaviour for amdgpu_fence.c
Here is the UBSAN dump:
[ 3.866656] index 2 is out of range for type 'amdgpu_uvd_inst [2]'
[ 3.866693] Workqueue: events work_for_cpu_fn
[ 3.866702] Call Trace:
[ 3.866710] dump_stack+0x85/0xc5
[ 3.866719] ubsan_epilogue+0x9/0x40
[ 3.866727] __ubsan_handle_out_of_bounds+0x89/0x90
[ 3.866737] ? rcu_read_lock_sched_held+0x58/0x60
[ 3.866746] ? __kmalloc+0x26c/0x2d0
[ 3.866846] amdgpu_fence_driver_start_ring+0x259/0x280 [amdgpu]
[ 3.866896] amdgpu_ring_init+0x12c/0x710 [amdgpu]
[ 3.866906] ? sprintf+0x42/0x50
[ 3.866956] amdgpu_gfx_kiq_init_ring+0x1bc/0x3a0 [amdgpu]
[ 3.867009] gfx_v8_0_sw_init+0x1ad3/0x2360 [amdgpu]
[ 3.867062] ? smu7_init+0xec/0x160 [amdgpu]
[ 3.867109] amdgpu_device_init+0x112c/0x1dc0 [amdgpu]
'ring->me' might be set as 2 with 'amdgpu_gfx_kiq_init_ring', that would
cause out of range for 'amdgpu_uvd_inst[2]'.
v2: simplified with ring type
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Michel Dänzer [Thu, 21 Jun 2018 09:27:46 +0000 (11:27 +0200)]
drm/amdgpu: GPU vs CPU page size fixes in amdgpu_vm_bo_split_mapping
start / last / max_entries are numbers of GPU pages, pfn / count are
numbers of CPU pages. Convert between them accordingly.
Fixes badness on systems with > 4K page size.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/106258
Reported-by: Matt Corallo <freedesktop@bluematt.me>
Tested-by: foxbat@ruin.net
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lyude Paul [Thu, 21 Jun 2018 20:48:26 +0000 (16:48 -0400)]
drm/amdgpu: Count disabled CRTCs in commit tail earlier
This fixes a regression I accidentally reduced that was picked up by
kasan, where we were checking the CRTC atomic states after DRM's helpers
had already freed them. Example:
==================================================================
BUG: KASAN: use-after-free in amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu]
Read of size 1 at addr
ffff8803a697b071 by task kworker/u16:0/7
CPU: 7 PID: 7 Comm: kworker/u16:0 Tainted: G O 4.18.0-rc1Lyude-Upstream+ #1
Hardware name: HP HP ZBook 15 G4/8275, BIOS P70 Ver. 01.21 05/02/2018
Workqueue: events_unbound commit_work [drm_kms_helper]
Call Trace:
dump_stack+0xc1/0x169
? dump_stack_print_info.cold.1+0x42/0x42
? kmsg_dump_rewind_nolock+0xd9/0xd9
? printk+0x9f/0xc5
? amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu]
print_address_description+0x6c/0x23c
? amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu]
kasan_report.cold.6+0x241/0x2fd
amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu]
? commit_planes_to_stream.constprop.45+0x13b0/0x13b0 [amdgpu]
? cpu_load_update_active+0x290/0x290
? finish_task_switch+0x2bd/0x840
? __switch_to_asm+0x34/0x70
? read_word_at_a_time+0xe/0x20
? strscpy+0x14b/0x460
? drm_atomic_helper_wait_for_dependencies+0x47d/0x7e0 [drm_kms_helper]
commit_tail+0x96/0xe0 [drm_kms_helper]
process_one_work+0x88a/0x1360
? create_worker+0x540/0x540
? __sched_text_start+0x8/0x8
? move_queued_task+0x760/0x760
? call_rcu_sched+0x20/0x20
? vsnprintf+0xcda/0x1350
? wait_woken+0x1c0/0x1c0
? mutex_unlock+0x1d/0x40
? init_timer_key+0x190/0x230
? schedule+0xea/0x390
? __schedule+0x1ea0/0x1ea0
? need_to_create_worker+0xe4/0x210
? init_worker_pool+0x700/0x700
? try_to_del_timer_sync+0xbf/0x110
? del_timer+0x120/0x120
? __mutex_lock_slowpath+0x10/0x10
worker_thread+0x196/0x11f0
? flush_rcu_work+0x50/0x50
? __switch_to_asm+0x34/0x70
? __switch_to_asm+0x34/0x70
? __switch_to_asm+0x40/0x70
? __switch_to_asm+0x34/0x70
? __switch_to_asm+0x40/0x70
? __switch_to_asm+0x34/0x70
? __switch_to_asm+0x40/0x70
? __schedule+0x7d6/0x1ea0
? migrate_swap_stop+0x850/0x880
? __sched_text_start+0x8/0x8
? save_stack+0x8c/0xb0
? kasan_kmalloc+0xbf/0xe0
? kmem_cache_alloc_trace+0xe4/0x190
? kthread+0x98/0x390
? ret_from_fork+0x35/0x40
? ret_from_fork+0x35/0x40
? deactivate_slab.isra.67+0x3c4/0x5c0
? kthread+0x98/0x390
? kthread+0x98/0x390
? set_track+0x76/0x120
? schedule+0xea/0x390
? __schedule+0x1ea0/0x1ea0
? wait_woken+0x1c0/0x1c0
? kasan_unpoison_shadow+0x30/0x40
? parse_args.cold.15+0x17a/0x17a
? flush_rcu_work+0x50/0x50
kthread+0x2d4/0x390
? kthread_create_worker_on_cpu+0xc0/0xc0
ret_from_fork+0x35/0x40
Allocated by task 1124:
kasan_kmalloc+0xbf/0xe0
kmem_cache_alloc_trace+0xe4/0x190
dm_crtc_duplicate_state+0x78/0x130 [amdgpu]
drm_atomic_get_crtc_state+0x147/0x410 [drm]
page_flip_common+0x57/0x230 [drm_kms_helper]
drm_atomic_helper_page_flip+0xa6/0x110 [drm_kms_helper]
drm_mode_page_flip_ioctl+0xc4b/0x10a0 [drm]
drm_ioctl_kernel+0x1d4/0x260 [drm]
drm_ioctl+0x433/0x920 [drm]
amdgpu_drm_ioctl+0x11d/0x290 [amdgpu]
do_vfs_ioctl+0x1a1/0x13d0
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x6f/0xb0
do_syscall_64+0x147/0x440
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Freed by task 1124:
__kasan_slab_free+0x12e/0x180
kfree+0x92/0x1a0
drm_atomic_state_default_clear+0x315/0xc40 [drm]
__drm_atomic_state_free+0x35/0xd0 [drm]
drm_atomic_helper_update_plane+0xac/0x350 [drm_kms_helper]
__setplane_internal+0x2d6/0x840 [drm]
drm_mode_cursor_universal+0x41e/0xbe0 [drm]
drm_mode_cursor_common+0x49f/0x880 [drm]
drm_mode_cursor_ioctl+0xd8/0x130 [drm]
drm_ioctl_kernel+0x1d4/0x260 [drm]
drm_ioctl+0x433/0x920 [drm]
amdgpu_drm_ioctl+0x11d/0x290 [amdgpu]
do_vfs_ioctl+0x1a1/0x13d0
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x6f/0xb0
do_syscall_64+0x147/0x440
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The buggy address belongs to the object at
ffff8803a697b068
which belongs to the cache kmalloc-1024 of size 1024
The buggy address is located 9 bytes inside of
1024-byte region [
ffff8803a697b068,
ffff8803a697b468)
The buggy address belongs to the page:
page:
ffffea000e9a5e00 count:1 mapcount:0 mapping:
ffff88041e00efc0 index:0x0 compound_mapcount: 0
flags: 0x8000000000008100(slab|head)
raw:
8000000000008100 ffffea000ecbc208 ffff88041e000c70 ffff88041e00efc0
raw:
0000000000000000 0000000000170017 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8803a697af00: fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8803a697af80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>
ffff8803a697b000: fc fc fc fc fc fc fc fc fc fc fc fc fc fb fb fb
^
ffff8803a697b080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8803a697b100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
So, we fix this by counting the number of CRTCs this atomic commit disabled
early on in the function before their atomic states have been freed, then use
that count later to do the appropriate number of RPM puts at the end of the
function.
Acked-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Fixes: 97028037a38ae ("drm/amdgpu: Grab/put runtime PM references in atomic_commit_tail()")
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Michel Dänzer <michel@daenzer.net>
Reported-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dave Airlie [Thu, 21 Jun 2018 23:58:57 +0000 (09:58 +1000)]
Merge tag 'drm-misc-fixes-2018-06-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for v4.18-rc2:
- A reversion of a commit in drm/sun4i to fix a run-time fault.
- Various fixes to the sii8620 bridge.
- Small bugfix to correctly check stride in atmel-hlcdc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/787d4bef-a579-4046-d0fc-f8c2c5b80c25@linux.intel.com
Dave Airlie [Thu, 21 Jun 2018 23:56:17 +0000 (09:56 +1000)]
Merge tag 'drm-intel-fixes-2018-06-21' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v4.18-rc2:
- Mostly cc: stable display fixes, including a DBLSCAN regression fix
- GEM fixes for this merge window
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87d0wkuypy.fsf@intel.com
Maciej Purski [Tue, 23 Jan 2018 11:17:19 +0000 (12:17 +0100)]
drm/bridge/sii8620: fix display of packed pixel modes in MHL2
Currently packed pixel modes in MHL2 can't be displayed. The device
automatically recognizes output format, so setting format other than
RGB causes failure. Fix it by writing proper values to registers.
Tested on MHL1 and MHL2 using various vendors' dongles both in
DVI and HDMI mode.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1516706239-9104-1-git-send-email-m.purski@samsung.com
Dave Airlie [Thu, 21 Jun 2018 00:13:05 +0000 (10:13 +1000)]
Merge branch 'drm-fixes-4.18' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Bunch of amdgpu fixes mostly all going to stable.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180620190021.2775-1-alexander.deucher@amd.com
Dave Airlie [Wed, 20 Jun 2018 06:58:46 +0000 (16:58 +1000)]
Merge tag 'drm-misc-fixes-2018-06-12' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Only a small qxl fix that was queued for v4.17.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/08dcbd63-ed18-6232-7bbd-547a3d63b90f@linux.intel.com
Dave Airlie [Wed, 20 Jun 2018 06:57:41 +0000 (16:57 +1000)]
Merge tag 'drm-misc-next-fixes-2018-06-15' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Single fix for v4.18:
- Fix possible race conditions while unplugging DRM device.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1fd8b7d1-e60a-0105-dfb5-d36f99ea0239@linux.intel.com
Dave Airlie [Wed, 20 Jun 2018 06:57:03 +0000 (16:57 +1000)]
Merge branch 'linux-4.18' of git://github.com/skeggsb/linux into drm-fixes
Single nouveau regression fix.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CACAvsv5VDDKaYKJShyVAGK0MJAHMZOJ02FKQ_aW5DnBCNVgRUw@mail.gmail.com
Michel Dänzer [Thu, 14 Jun 2018 11:02:07 +0000 (13:02 +0200)]
drm/amdgpu: Make amdgpu_vram_mgr_bo_invisible_size always accurate
Even BOs with AMDGPU_GEM_CREATE_NO_CPU_ACCESS may end up at least
partially in CPU visible VRAM, in particular when all VRAM is visible.
v2:
* Don't take VRAM mgr spinlock, not needed (Christian König)
* Make loop logic simpler and clearer.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Michel Dänzer [Tue, 12 Jun 2018 10:07:33 +0000 (12:07 +0200)]
drm/amdgpu: Refactor amdgpu_vram_mgr_bo_invisible_size helper
Preparation for the following fix, no functional change intended.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Michel Dänzer [Fri, 15 Jun 2018 09:06:56 +0000 (11:06 +0200)]
drm/amdgpu: Update pin_size values before unpinning BO
At least in theory, ttm_bo_validate may move the BO, in which case the
pin_size accounting would be inconsistent with when the BO was pinned.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
James Zhu [Mon, 18 Jun 2018 17:46:16 +0000 (13:46 -0400)]
drm/amdgpu:All UVD instances share one idle_work handle
All UVD instanses have only one dpm control, so it is better
to share one idle_work handle.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Harry Wentland [Tue, 8 May 2018 15:33:42 +0000 (11:33 -0400)]
drm/amdgpu: Don't default to DC support for Kaveri and older
We've had a number of users report failures to detect and light up
display with DC with LVDS and VGA. These connector types are not
currently supported with DC. I'd like to add support but unfortunately
don't have a system with LVDS or VGA available.
In order not to cause regressions we should probably fallback to the
non-DC driver for ASICs that support VGA and LVDS.
These ASICs are:
* Bonaire
* Kabini
* Kaveri
* Mullins
ASIC support can always be force enabled with amdgpu.dc=1
v2: Keep Hawaii on DC
v3: Added Mullins to the list
Cc: stable@vger.kernel.org
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Michel Dänzer [Fri, 8 Jun 2018 10:58:15 +0000 (12:58 +0200)]
drm/amdgpu: Use kvmalloc_array for allocating VRAM manager nodes array
It can be quite big, and there's no need for it to be physically
contiguous. This is less likely to fail under memory pressure (has
actually happened while running piglit).
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rajan Vaja [Mon, 18 Jun 2018 07:31:02 +0000 (13:01 +0530)]
drm/amd/pp: Fix uninitialized variable
Initialize variable to 0 before performing logical OR operation.
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Rajan Vaja <rajan.vaja@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kenneth Graunke [Fri, 15 Jun 2018 19:06:05 +0000 (20:06 +0100)]
drm/i915: Enable provoking vertex fix on Gen9 systems.
The SF and clipper units mishandle the provoking vertex in some cases,
which can cause misrendering with shaders that use flat shaded inputs.
There are chicken bits in 3D_CHICKEN3 (for SF) and FF_SLICE_CHICKEN
(for the clipper) that work around the issue. These registers are
unfortunately not part of the logical context (even the power context),
and so we must reload them every time we start executing in a context.
Bugzilla: https://bugs.freedesktop.org/103047
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615190605.16238-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
(cherry picked from commit
b77422f80337d363eed60c8c48db9cb6e33085c9)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Mika Kuoppala [Fri, 15 Jun 2018 10:44:29 +0000 (13:44 +0300)]
drm/i915: Fix context ban and hang accounting for client
If client is smart or lucky enough to create a new context
after each hang, our context banning mechanism will never
catch up, and as a result of that it will be saved from
client banning. This can result in a never ending streak of
gpu hangs caused by bad or malicious client, preventing
access from other legit gpu clients.
Fix this by always incrementing per client ban score if
it hangs in short successions regardless of context ban
scoring. The exception are non bannable contexts. They remain
detached from client ban scoring mechanism.
v2: xchg timestamp, tidyup (Chris)
v3: comment, bannable & banned together (Chris)
Fixes: b083a0870c79 ("drm/i915: Add per client max context ban limit")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615104429.31477-1-mika.kuoppala@linux.intel.com
(cherry picked from commit
14921f3cef85b0167a9145e5f29b9dfc3b2a84dc)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Wed, 13 Jun 2018 16:05:53 +0000 (19:05 +0300)]
drm/i915: Turn off g4x DP port in .post_disable()
While Bspec doesn't list a specific sequence for turning off the DP port
on g4x we are getting an underrun if the port is disabled in the
.disable() hook. Looks like the pipe stops when the port stops, and by
that time the plane disable may not have completed yet. Also the plane(s)
seem to end up in some wonky state when this happens as they also signal
another underrun immediately after we turn them back on during the next
enable sequence.
We could add a vblank wait in .disable() to avoid wedging the planes,
but I assume we're still tripping up the pipe in some way. So it seems
better to me to just follow the ILK+ sequence and turn off the DP port
in .post_disable() instead. This sequence doesn't seem to suffer from
this problem. Could be it was always the intended sequence for DP and
the gen4 bspec was just never updated to include it.
Originally we used the bad sequence even on ilk+, but I changed that
in commit
08aff3fe26ae ("drm/i915: Move DP port disable to post_disable
for pch platforms") as it was causing issues on those platforms as well.
I left out g4x then only because I didn't have the hardware to test it.
Now that I do it's fairly clear that the ilk+ sequence is also the
right choice for g4x.
v2: Fix whitespace fail (Jani)
Mention the ilk+ commit (Jani)
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit
51a9f6dfc00d35f927ecfaf6f0ae8ebaba39b3fe)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Wed, 13 Jun 2018 16:05:52 +0000 (19:05 +0300)]
drm/i915: Disallow interlaced modes on g4x DP outputs
Looks like interlaced DP output doesn't work on g4x either. Not all
that surprising considering we already established that interlaced
DP output is busted on VLV/CHV.
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-1-ville.syrjala@linux.intel.com
(cherry picked from commit
929168c5f3df5d9ea0ef426c33e971157d045eab)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Mon, 11 Jun 2018 20:02:55 +0000 (23:02 +0300)]
drm/i915: Fix PIPESTAT irq ack on i965/g4x
On i965/g4x IIR is edge triggered. So in order for IIR to notice that
there is still a pending interrupt we have to force and edge in ISR.
For the ISR/IIR pipe event bits we can do that by temporarily
clearing all the PIPESTAT enable bits when we ack the status bits.
This will force the ISR pipe event bit low, and it can then go back
high when we restore the PIPESTAT enable bits.
This avoids the following race:
1. stat = read(PIPESTAT)
2. an enabled PIPESTAT status bit goes high
3. write(PIPESTAT, enable|stat);
4. write(IIR, PIPE_EVENT)
The end result is IIR==0 and ISR!=0. This can lead to nasty
vblank wait/flip_done timeouts if another interrupt source
doesn't trick us into looking at the PIPESTAT status bits despite
the IIR PIPE_EVENT bit being low.
Before i965 IIR was level triggered so this problem can't actually
happen there. And curiously VLV/CHV went back to the level triggered
scheme as well. But for simplicity we'll use the same i965/g4x
compatible code for all platforms.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106033
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105225
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106030
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611200258.27121-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit
132c27c97cb958f637dc05adc35a61b47779bcd8)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Thu, 24 May 2018 12:54:03 +0000 (15:54 +0300)]
drm/i915: Allow DBLSCAN user modes with eDP/LVDS/DSI
When encountering a connector with the scaling mode property both
intel and modesetting ddxs sometimes add tons of DBLSCAN modes
to the output's mode list. The idea presumably being that since the
output will be going through the panel fitter anyway we can pretend
to use any kind of mode.
Sadly that means we can't reject user modes with the DBLSCAN flag
until we know whether we're going to be using the panel's native
mode or the user mode directly. Doing otherwise means X clients using
xf86vidmode/xrandr will get a protocol error (and often self
terminate as a result) when the kernel refuses to use the requested
mode with the DBLSCAN flag.
To undo the regression we'll move the DBLSCAN checks into the
connector->mode_valid() and encoder->compute_config() hooks.
Cc: stable@vger.kernel.org
Cc: Vito Caputo <vcaputo@pengaru.com>
Reported-by: Vito Caputo <vcaputo@pengaru.com>
Fixes: e995ca0b8139 ("drm/i915: Provide a device level .mode_valid() hook")
References: https://lkml.org/lkml/2018/5/21/715
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180524125403.23445-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106804
Tested-by: Arkadiusz Miskiewicz <arekm@maven.pl>
(cherry picked from commit
e4dd27aadd205417a2e9ea9902b698a0252ec3a0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Chris Wilson [Mon, 11 Jun 2018 15:33:32 +0000 (16:33 +0100)]
drm/i915/execlists: Avoid putting the error pointer
On allocation error, do not jump to the unwind handler that tries to
free the error pointer.
Reported-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: a89d1f921c15 ("drm/i915: Split i915_gem_timeline into individual timelines")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611153332.14824-1-chris@chris-wilson.co.uk
(cherry picked from commit
467d35789e5a4f47428b65ef711b30fdabbb0fd4)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Chris Wilson [Sun, 10 Jun 2018 19:43:09 +0000 (20:43 +0100)]
drm/i915: Apply batch location restrictions before pinning
We special case the position of the batch within the GTT to prevent
negative self-relocation deltas from underflowing. However, that
restriction is being applied after a trial pin of the batch in its
current position. Thus we are not rejecting an invalid location if the
batch has been used before, leading to an assertion if we happen to need
to rearrange the entire payload. In the worst case, this may cause a GPU
hang on gen7 or perhaps missing state.
References: https://bugs.freedesktop.org/show_bug.cgi?id=105720
Fixes: 2889caa92321 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Martin Peres <martin.peres@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180610194325.13467-2-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit
746c8f143afad7aaa66c484485fc39888d437a3f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ben Skeggs [Mon, 18 Jun 2018 08:06:13 +0000 (18:06 +1000)]
drm/nouveau/kms/nv50-: cursors always use core channel vram ctxdma
Ctxdmas for cursors from all heads are setup in the core channel, and due
to us tracking allocated handles per-window, we were failing with -EEXIST
on multiple-head setups trying to allocate duplicate handles.
The cursor code is hardcoded to use the core channel vram ctxdma already,
so just skip ctxdma allocation for cursor fbs to fix the issue.
Fixes: 5bca1621c07 ("drm/nouveau/kms/nv50-: move fb ctxdma tracking into windows")
Reported-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Paul Kocialkowski [Wed, 13 Jun 2018 08:16:47 +0000 (10:16 +0200)]
Revert "drm/sun4i: Handle DRM_BUS_FLAG_PIXDATA_*EDGE"
This reverts commit
2c17a4368aad2b88b68e4390c819e226cf320f70.
The offending commit triggers a run-time fault when accessing the panel
element of the sun4i_tcon structure when no such panel is attached.
It was apparently assumed in said commit that a panel is always used with
the TCON. Although it is often the case, this is not always true.
For instance a bridge might be used instead of a panel.
This issue was discovered using an A13-OLinuXino, that uses the TCON
in RGB mode for a simple DAC-based VGA bridge.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613081647.31183-1-paul.kocialkowski@bootlin.com
Stefan Agner [Sun, 17 Jun 2018 08:48:22 +0000 (10:48 +0200)]
drm/atmel-hlcdc: check stride values in the first plane
The statement always evaluates to true since the struct fields
are arrays. This has shown up as a warning when compiling with
clang:
warning: address of array 'desc->layout.xstride' will always
evaluate to 'true' [-Wpointer-bool-conversion]
Check for values in the first plane instead.
Fixes: 1a396789f65a ("drm: add Atmel HLCDC Display Controller support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180617084826.31885-1-stefan@agner.ch
Linus Torvalds [Sat, 16 Jun 2018 23:04:49 +0000 (08:04 +0900)]
Linux 4.18-rc1
Linus Torvalds [Sat, 16 Jun 2018 20:37:55 +0000 (05:37 +0900)]
Merge tag 'for-linus-
20180616' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes that should go into -rc1. This contains:
- bsg_open vs bsg_unregister race fix (Anatoliy)
- NVMe pull request from Christoph, with fixes for regressions in
this window, FC connect/reconnect path code unification, and a
trace point addition.
- timeout fix (Christoph)
- remove a few unused functions (Christoph)
- blk-mq tag_set reinit fix (Roman)"
* tag 'for-linus-
20180616' of git://git.kernel.dk/linux-block:
bsg: fix race of bsg_open and bsg_unregister
block: remov blk_queue_invalidate_tags
nvme-fabrics: fix and refine state checks in __nvmf_check_ready
nvme-fabrics: handle the admin-only case properly in nvmf_check_ready
nvme-fabrics: refactor queue ready check
blk-mq: remove blk_mq_tagset_iter
nvme: remove nvme_reinit_tagset
nvme-fc: fix nulling of queue data on reconnect
nvme-fc: remove reinit_request routine
blk-mq: don't time out requests again that are in the timeout handler
nvme-fc: change controllers first connect to use reconnect path
nvme: don't rely on the changed namespace list log
nvmet: free smart-log buffer after use
nvme-rdma: fix error flow during mapping request data
nvme: add bio remapping tracepoint
nvme: fix NULL pointer dereference in nvme_init_subsystem
blk-mq: reinit q->tag_set_list entry only after grace period
Linus Torvalds [Sat, 16 Jun 2018 20:25:18 +0000 (05:25 +0900)]
Merge tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental
Pull documentation fixes from Mauro Carvalho Chehab:
"This solves a series of broken links for files under Documentation,
and improves a script meant to detect such broken links (see
scripts/documentation-file-ref-check).
The changes on this series are:
- can.rst: fix a footnote reference;
- crypto_engine.rst: Fix two parsing warnings;
- Fix a lot of broken references to Documentation/*;
- improve the scripts/documentation-file-ref-check script, in order
to help detecting/fixing broken references, preventing
false-positives.
After this patch series, only 33 broken references to doc files are
detected by scripts/documentation-file-ref-check"
* tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental: (26 commits)
fix a series of Documentation/ broken file name references
Documentation: rstFlatTable.py: fix a broken reference
ABI: sysfs-devices-system-cpu: remove a broken reference
devicetree: fix a series of wrong file references
devicetree: fix name of pinctrl-bindings.txt
devicetree: fix some bindings file names
MAINTAINERS: fix location of DT npcm files
MAINTAINERS: fix location of some display DT bindings
kernel-parameters.txt: fix pointers to sound parameters
bindings: nvmem/zii: Fix location of nvmem.txt
docs: Fix more broken references
scripts/documentation-file-ref-check: check tools/*/Documentation
scripts/documentation-file-ref-check: get rid of false-positives
scripts/documentation-file-ref-check: hint: dash or underline
scripts/documentation-file-ref-check: add a fix logic for DT
scripts/documentation-file-ref-check: accept more wildcards at filenames
scripts/documentation-file-ref-check: fix help message
media: max2175: fix location of driver's companion documentation
media: v4l: fix broken video4linux docs locations
media: dvb: point to the location of the old README.dvb-usb file
...
Linus Torvalds [Sat, 16 Jun 2018 20:06:18 +0000 (05:06 +0900)]
Merge tag 'fsnotify_for_v4.18-rc1' of git://git./linux/kernel/git/jack/linux-fs
Pull fsnotify updates from Jan Kara:
"fsnotify cleanups unifying handling of different watch types.
This is the shortened fsnotify series from Amir with the last five
patches pulled out. Amir has modified those patches to not change
struct inode but obviously it's too late for those to go into this
merge window"
* tag 'fsnotify_for_v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fsnotify: add fsnotify_add_inode_mark() wrappers
fanotify: generalize fanotify_should_send_event()
fsnotify: generalize send_to_group()
fsnotify: generalize iteration of marks by object type
fsnotify: introduce marks iteration helpers
fsnotify: remove redundant arguments to handle_event()
fsnotify: use type id to identify connector object type
Linus Torvalds [Sat, 16 Jun 2018 20:00:24 +0000 (05:00 +0900)]
Merge tag 'fbdev-v4.18' of git://github.com/bzolnier/linux
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"There is nothing really major here, few small fixes, some cleanups and
dead drivers removal:
- mark omapfb drivers as orphans in MAINTAINERS file (Tomi Valkeinen)
- add missing module license tags to omap/omapfb driver (Arnd
Bergmann)
- add missing GPIOLIB dependendy to omap2/omapfb driver (Arnd
Bergmann)
- convert savagefb, aty128fb & radeonfb drivers to use msleep & co.
(Jia-Ju Bai)
- allow COMPILE_TEST build for viafb driver (media part was reviewed
by media subsystem Maintainer)
- remove unused MERAM support from sh_mobile_lcdcfb and shmob-drm
drivers (drm parts were acked by shmob-drm driver Maintainer)
- remove unused auo_k190xfb drivers
- misc cleanups (Souptick Joarder, Wolfram Sang, Markus Elfring, Andy
Shevchenko, Colin Ian King)"
* tag 'fbdev-v4.18' of git://github.com/bzolnier/linux: (26 commits)
fb_omap2: add gpiolib dependency
video/omap: add module license tags
MAINTAINERS: make omapfb orphan
video: fbdev: pxafb: match_string() conversion fixup
video: fbdev: nvidia: fix spelling mistake: "scaleing" -> "scaling"
video: fbdev: fix spelling mistake: "frambuffer" -> "framebuffer"
video: fbdev: pxafb: Convert to use match_string() helper
video: fbdev: via: allow COMPILE_TEST build
video: fbdev: remove unused sh_mobile_meram driver
drm: shmobile: remove unused MERAM support
video: fbdev: sh_mobile_lcdcfb: remove unused MERAM support
video: fbdev: remove unused auo_k190xfb drivers
video: omap: Improve a size determination in omapfb_do_probe()
video: sm501fb: Improve a size determination in sm501fb_probe()
video: fbdev-MMP: Improve a size determination in path_init()
video: fbdev-MMP: Delete an error message for a failed memory allocation in two functions
video: auo_k190x: Delete an error message for a failed memory allocation in auok190x_common_probe()
video: sh_mobile_lcdcfb: Delete an error message for a failed memory allocation in two functions
video: sh_mobile_meram: Delete an error message for a failed memory allocation in sh_mobile_meram_probe()
video: fbdev: sh_mobile_meram: Drop SUPERH platform dependency
...
Linus Torvalds [Sat, 16 Jun 2018 07:32:04 +0000 (16:32 +0900)]
Merge branch 'afs-proc' of git://git./linux/kernel/git/viro/vfs
Pull AFS updates from Al Viro:
"Assorted AFS stuff - ended up in vfs.git since most of that consists
of David's AFS-related followups to Christoph's procfs series"
* 'afs-proc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
afs: Optimise callback breaking by not repeating volume lookup
afs: Display manually added cells in dynamic root mount
afs: Enable IPv6 DNS lookups
afs: Show all of a server's addresses in /proc/fs/afs/servers
afs: Handle CONFIG_PROC_FS=n
proc: Make inline name size calculation automatic
afs: Implement network namespacing
afs: Mark afs_net::ws_cell as __rcu and set using rcu functions
afs: Fix a Sparse warning in xdr_decode_AFSFetchStatus()
proc: Add a way to make network proc files writable
afs: Rearrange fs/afs/proc.c to remove remaining predeclarations.
afs: Rearrange fs/afs/proc.c to move the show routines up
afs: Rearrange fs/afs/proc.c by moving fops and open functions down
afs: Move /proc management functions to the end of the file
Linus Torvalds [Sat, 16 Jun 2018 07:21:50 +0000 (16:21 +0900)]
Merge branch 'work.compat' of git://git./linux/kernel/git/viro/vfs
Pull compat updates from Al Viro:
"Some biarch patches - getting rid of assorted (mis)uses of
compat_alloc_user_space().
Not much in that area this cycle..."
* 'work.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
orangefs: simplify compat ioctl handling
signalfd: lift sigmask copyin and size checks to callers of do_signalfd4()
vmsplice(): lift importing iovec into vmsplice(2) and compat counterpart
Linus Torvalds [Sat, 16 Jun 2018 07:11:40 +0000 (16:11 +0900)]
Merge branch 'work.aio' of git://git./linux/kernel/git/viro/vfs
Pull aio fixes from Al Viro:
"Assorted AIO followups and fixes"
* 'work.aio' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
eventpoll: switch to ->poll_mask
aio: only return events requested in poll_mask() for IOCB_CMD_POLL
eventfd: only return events requested in poll_mask()
aio: mark __aio_sigset::sigmask const
Linus Torvalds [Fri, 15 Jun 2018 22:39:34 +0000 (07:39 +0900)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Various netfilter fixlets from Pablo and the netfilter team.
2) Fix regression in IPVS caused by lack of PMTU exceptions on local
routes in ipv6, from Julian Anastasov.
3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.
4) Don't crash on poll in TLS, from Daniel Borkmann.
5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
including Avahi mDNS. From Bart Van Assche.
6) Missing of_node_put in qcom/emac driver, from Yue Haibing.
7) We lack checking of the TCP checking in one special case during SYN
receive, from Frank van der Linden.
8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.
9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.
10) Must grab HW caps before doing quirk checks in stmmac driver, from
Jose Abreu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: stmmac: Run HWIF Quirks after getting HW caps
neighbour: skip NTF_EXT_LEARNED entries during forced gc
net: cxgb3: add error handling for sysfs_create_group
tls: fix waitall behavior in tls_sw_recvmsg
tls: fix use-after-free in tls_push_record
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
mlxsw: spectrum_router: Align with new route replace logic
mlxsw: spectrum_router: Allow appending to dev-only routes
ipv6: Only emit append events for appended routes
stmmac: added support for 802.1ad vlan stripping
cfg80211: fix rcu in cfg80211_unregister_wdev
mac80211: Move up init of TXQs
mac80211_hwsim: fix module init error paths
cfg80211: initialize sinfo in cfg80211_get_station
nl80211: fix some kernel doc tag mistakes
hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
rds: avoid unenecessary cong_update in loop transport
l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
...
Linus Torvalds [Fri, 15 Jun 2018 22:36:39 +0000 (07:36 +0900)]
Merge tag 'modules-for-v4.18' of git://git./linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Minor code cleanup and also allow sig_enforce param to be shown in
sysfs with CONFIG_MODULE_SIG_FORCE"
* tag 'modules-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Allow to always show the status of modsign
module: Do not access sig_enforce directly
Linus Torvalds [Fri, 15 Jun 2018 21:50:51 +0000 (06:50 +0900)]
Merge branch 'for-linus-4.18-rc1' of git://git./linux/kernel/git/rw/uml
Pull uml updates from Richard Weinberger:
"Minor updates for UML:
- fixes for our new vector network driver by Anton
- initcall cleanup by Alexander
- We have a new mailinglist, sourceforge.net sucks"
* 'for-linus-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Fix raw interface options
um: Fix initialization of vector queues
um: remove uml initcalls
um: Update mailing list address
Linus Torvalds [Fri, 15 Jun 2018 21:42:43 +0000 (06:42 +0900)]
Merge tag 'riscv-for-linus-4.18-merge_window' of git://git./linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains some small RISC-V updates I'd like to target for 4.18.
They are all fairly small this time. Here's a short summary, there's
more info in the commits/merges:
- a fix to __clear_user to respect the passed arguments.
- enough support for the perf subsystem to work with RISC-V's ISA
defined performance counters.
- support for sparse and cleanups suggested by it.
- support for R_RISCV_32 (a relocation, not the 32-bit ISA).
- some MAINTAINERS cleanups.
- the addition of CONFIG_HVC_RISCV_SBI to our defconfig, as it's
always present.
I've given these a simple build+boot test"
* tag 'riscv-for-linus-4.18-merge_window' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
RISC-V: Add CONFIG_HVC_RISCV_SBI=y to defconfig
RISC-V: Handle R_RISCV_32 in modules
riscv/ftrace: Export _mcount when DYNAMIC_FTRACE isn't set
riscv: add riscv-specific predefines to CHECKFLAGS
riscv: split the declaration of __copy_user
riscv: no __user for probe_kernel_address()
riscv: use NULL instead of a plain 0
perf: riscv: Add Document for Future Porting Guide
perf: riscv: preliminary RISC-V support
MAINTAINERS: Update Albert's email, he's back at Berkeley
MAINTAINERS: Add myself as a maintainer for SiFive's drivers
riscv: Fix the bug in memory access fixup code
Linus Torvalds [Fri, 15 Jun 2018 21:37:04 +0000 (06:37 +0900)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull more kvm updates from Paolo Bonzini:
"Mostly the PPC part of the release, but also switching to Arnd's fix
for the hyperv config issue and a typo fix.
Main PPC changes:
- reimplement the MMIO instruction emulation
- transactional memory support for PR KVM
- improve radix page table handling"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (63 commits)
KVM: x86: VMX: redo fix for link error without CONFIG_HYPERV
KVM: x86: fix typo at kvm_arch_hardware_setup comment
KVM: PPC: Book3S PR: Fix failure status setting in tabort. emulation
KVM: PPC: Book3S PR: Enable use on POWER9 bare-metal hosts in HPT mode
KVM: PPC: Book3S PR: Don't let PAPR guest set MSR hypervisor bit
KVM: PPC: Book3S PR: Fix failure status setting in treclaim. emulation
KVM: PPC: Book3S PR: Fix MSR setting when delivering interrupts
KVM: PPC: Book3S PR: Handle additional interrupt types
KVM: PPC: Book3S PR: Enable kvmppc_get/set_one_reg_pr() for HTM registers
KVM: PPC: Book3S: Remove load/put vcpu for KVM_GET_REGS/KVM_SET_REGS
KVM: PPC: Remove load/put vcpu for KVM_GET/SET_ONE_REG ioctl
KVM: PPC: Move vcpu_load/vcpu_put down to each ioctl case in kvm_arch_vcpu_ioctl
KVM: PPC: Book3S PR: Enable HTM for PR KVM for KVM_CHECK_EXTENSION ioctl
KVM: PPC: Book3S PR: Support TAR handling for PR KVM HTM
KVM: PPC: Book3S PR: Add guard code to prevent returning to guest with PR=0 and Transactional state
KVM: PPC: Book3S PR: Add emulation for tabort. in privileged state
KVM: PPC: Book3S PR: Add emulation for trechkpt.
KVM: PPC: Book3S PR: Add emulation for treclaim.
KVM: PPC: Book3S PR: Restore NV regs after emulating mfspr from TM SPRs
KVM: PPC: Book3S PR: Always fail transactions in guest privileged state
...
Linus Torvalds [Fri, 15 Jun 2018 21:35:02 +0000 (06:35 +0900)]
Merge tag 'for_linus' of git://git./linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"virtio, vhost: features, fixes
- PCI virtual function support for virtio
- DMA barriers for virtio strong barriers
- bugfixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio: update the comments for transport features
virtio_pci: support enabling VFs
vhost: fix info leak due to uninitialized memory
virtio_ring: switch to dma_XX barriers for rpmsg
Mauro Carvalho Chehab [Thu, 14 Jun 2018 15:34:32 +0000 (12:34 -0300)]
fix a series of Documentation/ broken file name references
As files move around, their previous links break. Fix the
references for them.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 15:33:06 +0000 (12:33 -0300)]
Documentation: rstFlatTable.py: fix a broken reference
The old HOWTO was removed a long time ago. The flat table
version is not metioned elsewhere, so just get rid of the
text.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 15:32:05 +0000 (12:32 -0300)]
ABI: sysfs-devices-system-cpu: remove a broken reference
This file doesn't exist anymore:
Documentation/cpu-freq/user-guide.txt
As the ABI already points to Documentation/cpu-freq, just
remove the broken link and the associated text.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 15:30:30 +0000 (12:30 -0300)]
devicetree: fix a series of wrong file references
As files got renamed, their references broke.
Manually fix a series of broken refs at the DT bindings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 15:24:41 +0000 (12:24 -0300)]
devicetree: fix name of pinctrl-bindings.txt
Rename:
pinctrl-binding.txt -> pinctrl-bindings.txt
In order to match the current name of this file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 12:39:01 +0000 (09:39 -0300)]
devicetree: fix some bindings file names
There were some file movements that changed the location for
some DT bindings. Fix them with:
scripts/documentation-file-ref-check --fix
After manually checking if the new file makes sense.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 11:59:37 +0000 (08:59 -0300)]
MAINTAINERS: fix location of DT npcm files
The specified locations are not right. Fix the wildcard logic
to point to the correct directories.
Without that, get-maintainer won't get things right:
$ ./scripts/get_maintainer.pl --no-git-fallback --no-r --no-n --no-l -f Documentation/devicetree/bindings/arm/cpu-enable-method/nuvoton,npcm750-smp
robh+dt@kernel.org (maintainer:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS)
mark.rutland@arm.com (maintainer:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS)
After the patch, it will properly point to NPCM arch maintainers:
$ ./scripts/get_maintainer.pl --no-git-fallback --no-r --no-n --no-l -f Documentation/devicetree/bindings/arm/cpu-enable-method/nuvoton,npcm750-smp
avifishman70@gmail.com (supporter:ARM/NUVOTON NPCM ARCHITECTURE)
tmaimon77@gmail.com (supporter:ARM/NUVOTON NPCM ARCHITECTURE)
robh+dt@kernel.org (maintainer:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS)
mark.rutland@arm.com (maintainer:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS)
Cc: Avi Fishman <avifishman70@gmail.com>
Cc: Tomer Maimon <tmaimon77@gmail.com>
Cc: Patrick Venture <venture@google.com>
Cc: Nancy Yuen <yuenn@google.com>
Cc: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 11:01:00 +0000 (08:01 -0300)]
MAINTAINERS: fix location of some display DT bindings
Those files got a manufacturer's name prepended and were moved around.
Adjust their references accordingly.
Also, due those movements, Documentation/devicetree/bindings/video
doesn't exist anymore.
Cc: David Airlie <airlied@linux.ie>
Cc: David Lechner <david@lechnology.com>
Cc: Peter Senna Tschudin <peter.senna@collabora.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@nxp.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 10:43:07 +0000 (07:43 -0300)]
kernel-parameters.txt: fix pointers to sound parameters
The alsa parameters file was renamed to alsa-configuration.rst.
With regards to OSS, it got retired as a hole by at changeset
727dede0ba8a ("sound: Retire OSS"). So, it doesn't make sense
to keep mentioning it at kernel-parameters.txt.
Fixes: 727dede0ba8a ("sound: Retire OSS")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 10:18:45 +0000 (07:18 -0300)]
bindings: nvmem/zii: Fix location of nvmem.txt
The location pointed there is missing "bindings/" on its path.
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Tue, 8 May 2018 18:14:57 +0000 (15:14 -0300)]
docs: Fix more broken references
As we move stuff around, some doc references are broken. Fix some of
them via this script:
./scripts/documentation-file-ref-check --fix
Manually checked that produced results are valid.
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 14:06:08 +0000 (11:06 -0300)]
scripts/documentation-file-ref-check: check tools/*/Documentation
Some files, like tools/memory-model/README has references to
a Documentation file that is locale to it. Handle references
that are relative to them too.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 13:47:29 +0000 (10:47 -0300)]
scripts/documentation-file-ref-check: get rid of false-positives
Now that the number of broken refs are smaller, improve the logic
that gets rid of false-positives.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 13:14:54 +0000 (10:14 -0300)]
scripts/documentation-file-ref-check: hint: dash or underline
Sometimes, people use dash instead of underline or vice-versa.
Try to autocorrect it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 12:36:35 +0000 (09:36 -0300)]
scripts/documentation-file-ref-check: add a fix logic for DT
There are several links broken due to DT file movements. Add
a hint logic to seek for those changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 10:48:22 +0000 (07:48 -0300)]
scripts/documentation-file-ref-check: accept more wildcards at filenames
at MAINTAINERS, some filename paths use '?' and things like [7,9].
So, accept more wildcards, in order to avoid false-positives.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 10:11:02 +0000 (07:11 -0300)]
scripts/documentation-file-ref-check: fix help message
The name of the --fix option was renamed, but it was not
changed at the quick help message.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Thu, 14 Jun 2018 10:34:51 +0000 (07:34 -0300)]
media: max2175: fix location of driver's companion documentation
There's a missing ".rst" at the doc's file name.
Acked-by: Ramesh Shanmugasundaram <Ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Tue, 8 May 2018 22:41:44 +0000 (19:41 -0300)]
media: v4l: fix broken video4linux docs locations
There are several places pointing to old documentation files:
Documentation/video4linux/API.html
Documentation/video4linux/bttv/
Documentation/video4linux/cx2341x/fw-encoder-api.txt
Documentation/video4linux/m5602.txt
Documentation/video4linux/v4l2-framework.txt
Documentation/video4linux/videobuf
Documentation/video4linux/Zoran
Make them point to the new location where available, removing
otherwise.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Tue, 8 May 2018 21:29:30 +0000 (18:29 -0300)]
media: dvb: point to the location of the old README.dvb-usb file
This file got renamed, but the references still point to the
old place.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Tue, 8 May 2018 21:10:05 +0000 (18:10 -0300)]
media: dvb: fix location of get_dvb_firmware script
This script was moved out of Documentation/dvb, but the
links weren't updated.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Tue, 8 May 2018 18:14:57 +0000 (15:14 -0300)]
docs: Fix some broken references
As we move stuff around, some doc references are broken. Fix some of
them via this script:
./scripts/documentation-file-ref-check --fix
Manually checked if the produced result is valid, removing a few
false-positives.
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Tue, 8 May 2018 21:54:36 +0000 (18:54 -0300)]
docs: fix broken references with multiple hints
The script:
./scripts/documentation-file-ref-check --fix
Gives multiple hints for broken references on some files.
Manually use the one that applies for some files.
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Jose Abreu [Fri, 15 Jun 2018 15:17:27 +0000 (16:17 +0100)]
net: stmmac: Run HWIF Quirks after getting HW caps
Currently we were running HWIF quirks before getting HW capabilities.
This is not right because some HWIF callbacks depend on HW caps.
Lets save the quirks callback and use it in a later stage.
This fixes Altera socfpga.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: 5f0456b43140 ("net: stmmac: Implement logic to automatically select HW Interface")
Reported-by: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu [Wed, 13 Jun 2018 04:26:10 +0000 (21:26 -0700)]
neighbour: skip NTF_EXT_LEARNED entries during forced gc
Commit
9ce33e46531d ("neighbour: support for NTF_EXT_LEARNED flag")
added support for NTF_EXT_LEARNED for neighbour entries.
NTF_EXT_LEARNED entries are neigh entries managed by control
plane (eg: Ethernet VPN implementation in FRR routing suite).
Periodic gc already excludes these entries. This patch extends
it to forced gc which the earlier patch missed.
Fixes: 9ce33e46531d ("neighbour: support for NTF_EXT_LEARNED flag")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhouyang Jia [Fri, 15 Jun 2018 03:06:17 +0000 (11:06 +0800)]
net: cxgb3: add error handling for sysfs_create_group
When sysfs_create_group fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling sysfs_create_group.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Jun 2018 16:14:31 +0000 (09:14 -0700)]
Merge branch 'tls-fixes'
Daniel Borkmann says:
====================
Two tls fixes
First one is syzkaller trigered uaf and second one noticed
while writing test code with tls ulp. For details please see
individual patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 15 Jun 2018 01:07:46 +0000 (03:07 +0200)]
tls: fix waitall behavior in tls_sw_recvmsg
Current behavior in tls_sw_recvmsg() is to wait for incoming tls
messages and copy up to exactly len bytes of data that the user
provided. This is problematic in the sense that i) if no packet
is currently queued in strparser we keep waiting until one has been
processed and pushed into tls receive layer for tls_wait_data() to
wake up and push the decrypted bits to user space. Given after
tls decryption, we're back at streaming data, use sock_rcvlowat()
hint from tcp socket instead. Retain current behavior with MSG_WAITALL
flag and otherwise use the hint target for breaking the loop and
returning to application. This is done if currently no ctx->recv_pkt
is ready, otherwise continue to process it from our strparser
backlog.
Fixes: c46234ebb4d1 ("tls: RX path for ktls")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 15 Jun 2018 01:07:45 +0000 (03:07 +0200)]
tls: fix use-after-free in tls_push_record
syzkaller managed to trigger a use-after-free in tls like the
following:
BUG: KASAN: use-after-free in tls_push_record.constprop.15+0x6a2/0x810 [tls]
Write of size 1 at addr
ffff88037aa08000 by task a.out/2317
CPU: 3 PID: 2317 Comm: a.out Not tainted 4.17.0+ #144
Hardware name: LENOVO 20FBCTO1WW/20FBCTO1WW, BIOS N1FET47W (1.21 ) 11/28/2016
Call Trace:
dump_stack+0x71/0xab
print_address_description+0x6a/0x280
kasan_report+0x258/0x380
? tls_push_record.constprop.15+0x6a2/0x810 [tls]
tls_push_record.constprop.15+0x6a2/0x810 [tls]
tls_sw_push_pending_record+0x2e/0x40 [tls]
tls_sk_proto_close+0x3fe/0x710 [tls]
? tcp_check_oom+0x4c0/0x4c0
? tls_write_space+0x260/0x260 [tls]
? kmem_cache_free+0x88/0x1f0
inet_release+0xd6/0x1b0
__sock_release+0xc0/0x240
sock_close+0x11/0x20
__fput+0x22d/0x660
task_work_run+0x114/0x1a0
do_exit+0x71a/0x2780
? mm_update_next_owner+0x650/0x650
? handle_mm_fault+0x2f5/0x5f0
? __do_page_fault+0x44f/0xa50
? mm_fault_error+0x2d0/0x2d0
do_group_exit+0xde/0x300
__x64_sys_exit_group+0x3a/0x50
do_syscall_64+0x9a/0x300
? page_fault+0x8/0x30
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This happened through fault injection where aead_req allocation in
tls_do_encryption() eventually failed and we returned -ENOMEM from
the function. Turns out that the use-after-free is triggered from
tls_sw_sendmsg() in the second tls_push_record(). The error then
triggers a jump to waiting for memory in sk_stream_wait_memory()
resp. returning immediately in case of MSG_DONTWAIT. What follows is
the trim_both_sgl(sk, orig_size), which drops elements from the sg
list added via tls_sw_sendmsg(). Now the use-after-free gets triggered
when the socket is being closed, where tls_sk_proto_close() callback
is invoked. The tls_complete_pending_work() will figure that there's
a pending closed tls record to be flushed and thus calls into the
tls_push_pending_closed_record() from there. ctx->push_pending_record()
is called from the latter, which is the tls_sw_push_pending_record()
from sw path. This again calls into tls_push_record(). And here the
tls_fill_prepend() will panic since the buffer address has been freed
earlier via trim_both_sgl(). One way to fix it is to move the aead
request allocation out of tls_do_encryption() early into tls_push_record().
This means we don't prep the tls header and advance state to the
TLS_PENDING_CLOSED_RECORD before allocation which could potentially
fail happened. That fixes the issue on my side.
Fixes: 3c4d7559159b ("tls: kernel TLS support")
Reported-by: syzbot+5c74af81c547738e1684@syzkaller.appspotmail.com
Reported-by: syzbot+709f2810a6a05f11d4d3@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Jun 2018 16:12:37 +0000 (09:12 -0700)]
Merge branch 'l2tp-l2tp_ppp-must-ignore-non-PPP-sessions'
Guillaume Nault says:
====================
l2tp: l2tp_ppp must ignore non-PPP sessions
The original L2TP code was written for version 2 of the protocol, which
could only carry PPP sessions. Then L2TPv3 generalised the protocol so that
it could transport different kinds of pseudo-wires. But parts of the
l2tp_ppp module still break in presence of non-PPP sessions.
Assuming L2TPv2 tunnels can only transport PPP sessions is right, but
l2tp_netlink failed to ensure that (fixed in patch 1).
When retrieving a session from an arbitrary tunnel, l2tp_ppp needs to
filter out non-PPP sessions (last occurrence fixed in patch 2).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 15 Jun 2018 13:39:19 +0000 (15:39 +0200)]
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
pppol2tp_tunnel_ioctl() can act on an L2TPv3 tunnel, in which case
'session' may be an Ethernet pseudo-wire.
However, pppol2tp_session_ioctl() expects a PPP pseudo-wire, as it
assumes l2tp_session_priv() points to a pppol2tp_session structure. For
an Ethernet pseudo-wire l2tp_session_priv() points to an l2tp_eth_sess
structure instead, making pppol2tp_session_ioctl() access invalid
memory.
Fixes: d9e31d17ceba ("l2tp: Add L2TP ethernet pseudowire support")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 15 Jun 2018 13:39:17 +0000 (15:39 +0200)]
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
The /proc/net/pppol2tp handlers (pppol2tp_seq_*()) iterate over all
L2TPv2 tunnels, and rightfully expect that only PPP sessions can be
found there. However, l2tp_netlink accepts creating Ethernet sessions
regardless of the underlying tunnel version.
This confuses pppol2tp_seq_session_show(), which expects that
l2tp_session_priv() returns a pppol2tp_session structure. When the
session is an Ethernet pseudo-wire, a struct l2tp_eth_sess is returned
instead. This leads to invalid memory access when
pppol2tp_session_get_sock() later tries to dereference ps->sk.
Fixes: d9e31d17ceba ("l2tp: Add L2TP ethernet pseudowire support")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Jun 2018 16:11:17 +0000 (09:11 -0700)]
Merge branch 'mlxsw-IPv6-and-reference-counting-fixes'
Ido Schimmel says:
====================
mlxsw: IPv6 and reference counting fixes
The first three patches fix a mismatch between the new IPv6 behavior
introduced in commit
f34436a43092 ("net/ipv6: Simplify route replace and
appending into multipath route") and mlxsw. The patches allow the driver
to support multipathing in IPv6 overlays with GRE tunnel devices. A
selftest will be submitted when net-next opens.
The last patch fixes a reference count problem of the port_vlan struct.
I plan to simplify the code in net-next, so that reference counting is
not necessary anymore.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Fri, 15 Jun 2018 13:23:38 +0000 (16:23 +0300)]
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
Switchdev notifications for addition of SWITCHDEV_OBJ_ID_PORT_VLAN are
distributed not only on clean addition, but also when flags on an
existing VLAN are changed. mlxsw_sp_bridge_port_vlan_add() calls
mlxsw_sp_port_vlan_get() to get at the port_vlan in question, which
implicitly references the object. This then leads to discrepancies in
reference counting when the VLAN is removed. spectrum.c warns about the
problem when the module is removed:
[13578.493090] WARNING: CPU: 0 PID: 2454 at drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2973 mlxsw_sp_port_remove+0xfd/0x110 [mlxsw_spectrum]
[...]
[13578.627106] Call Trace:
[13578.629617] mlxsw_sp_fini+0x2a/0xe0 [mlxsw_spectrum]
[13578.634748] mlxsw_core_bus_device_unregister+0x3e/0x130 [mlxsw_core]
[13578.641290] mlxsw_pci_remove+0x13/0x40 [mlxsw_pci]
[13578.646238] pci_device_remove+0x31/0xb0
[13578.650244] device_release_driver_internal+0x14f/0x220
[13578.655562] driver_detach+0x32/0x70
[13578.659183] bus_remove_driver+0x47/0xa0
[13578.663134] pci_unregister_driver+0x1e/0x80
[13578.667486] mlxsw_sp_module_exit+0xc/0x3fa [mlxsw_spectrum]
[13578.673207] __x64_sys_delete_module+0x13b/0x1e0
[13578.677888] ? exit_to_usermode_loop+0x78/0x80
[13578.682374] do_syscall_64+0x39/0xe0
[13578.685976] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix by putting the port_vlan when mlxsw_sp_port_vlan_bridge_join()
determines it's a flag-only change.
Fixes: b3529af6bb0d ("spectrum: Reference count VLAN entries")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 15 Jun 2018 13:23:37 +0000 (16:23 +0300)]
mlxsw: spectrum_router: Align with new route replace logic
Commit
f34436a43092 ("net/ipv6: Simplify route replace and appending
into multipath route") changed the IPv6 route replace logic so that the
first matching route (i.e., same metric) is replaced.
Have mlxsw replace the first matching route as well.
Fixes: f34436a43092 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 15 Jun 2018 13:23:36 +0000 (16:23 +0300)]
mlxsw: spectrum_router: Allow appending to dev-only routes
Commit
f34436a43092 ("net/ipv6: Simplify route replace and appending
into multipath route") changed the IPv6 route append logic so that
dev-only routes can be appended and not only gatewayed routes.
Align mlxsw with the new behaviour.
Fixes: f34436a43092 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 15 Jun 2018 13:23:35 +0000 (16:23 +0300)]
ipv6: Only emit append events for appended routes
Current code will emit an append event in the FIB notification chain for
any route added with NLM_F_APPEND set, even if the route was not
appended to any existing route.
This is inconsistent with IPv4 where such an event is only emitted when
the new route is appended after an existing one.
Align IPv6 behavior with IPv4, thereby allowing listeners to more easily
handle these events.
Fixes: f34436a43092 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Jun 2018 16:08:26 +0000 (09:08 -0700)]
Merge tag 'mac80211-for-davem-2018-06-15' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A handful of fixes:
* missing RCU grace period enforcement led to drivers freeing
data structures before; fix from Dedy Lansky.
* hwsim module init error paths were messed up; fixed it myself
after a report from Colin King (who had sent a partial patch)
* kernel-doc tag errors; fix from Luca Coelho
* initialize the on-stack sinfo data structure when getting
station information; fix from Sven Eckelmann
* TXQ state dumping is now done from init, and when TXQs aren't
initialized yet at that point, bad things happen, move the
initialization; fix from Toke Høiland-Jørgensen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Elad Nachman [Fri, 15 Jun 2018 06:57:39 +0000 (09:57 +0300)]
stmmac: added support for 802.1ad vlan stripping
stmmac reception handler calls stmmac_rx_vlan() to strip the vlan before
calling napi_gro_receive().
The function assumes VLAN tagged frames are always tagged with
802.1Q protocol, and assigns ETH_P_8021Q to the skb by hard-coding
the parameter on call to __vlan_hwaccel_put_tag() .
This causes packets not to be passed to the VLAN slave if it was created
with 802.1AD protocol
(ip link add link eth0 eth0.100 type vlan proto 802.1ad id 100).
This fix passes the protocol from the VLAN header into
__vlan_hwaccel_put_tag() instead of using the hard-coded value of
ETH_P_8021Q.
NETIF_F_HW_VLAN_STAG_RX check was added and the strip action is now
dependent on the correct combination of features and the detected vlan tag.
NETIF_F_HW_VLAN_STAG_RX feature was added to be in line with the driver
actual abilities.
Signed-off-by: Elad Nachman <eladn@gilat.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mauro Carvalho Chehab [Wed, 9 May 2018 02:44:08 +0000 (23:44 -0300)]
arch/*: Kconfig: fix documentation for NMI watchdog
Changeset
9919cba7ff71 ("watchdog: Update documentation") updated
the documentation, removing the old nmi_watchdog.txt and adding
a file with a new content.
Update Kconfig files accordingly.
Fixes: 9919cba7ff71 ("watchdog: Update documentation")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Sun, 6 May 2018 17:30:09 +0000 (14:30 -0300)]
docs: crypto_engine.rst: Fix two parse warnings
./Documentation/crypto/crypto_engine.rst:13: WARNING: Unexpected indentation.
./Documentation/crypto/crypto_engine.rst:15: WARNING: Block quote ends without a blank line; unexpected unindent.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Mauro Carvalho Chehab [Sun, 6 May 2018 15:00:11 +0000 (12:00 -0300)]
docs: can.rst: fix a footnote reference
As stated at:
http://www.sphinx-doc.org/en/master/usage/restructuredtext/basics.html#footnotes
A footnote should contain either a number, a reference or
an auto number, e. g.:
[1], [#f1] or [#].
While using [*] accidentaly works for html, it fails for other
document outputs. In particular, it causes an error with LaTeX
output, causing all books after networking to not be built.
So, replace it by a valid syntax.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
David Howells [Fri, 15 Jun 2018 14:24:50 +0000 (15:24 +0100)]
afs: Optimise callback breaking by not repeating volume lookup
At the moment, afs_break_callbacks calls afs_break_one_callback() for each
separate FID it was given, and the latter looks up the volume individually
for each one.
However, this is inefficient if two or more FIDs have the same vid as we
could reuse the volume. This is complicated by cell aliasing whereby we
may have multiple cells sharing a volume and can therefore have multiple
callback interests for any particular volume ID.
At the moment afs_break_one_callback() scans the entire list of volumes
we're getting from a server and breaks the appropriate callback in every
matching volume, regardless of cell. This scan is done for every FID.
Optimise callback breaking by the following means:
(1) Sort the FID list by vid so that all FIDs belonging to the same volume
are clumped together.
This is done through the use of an indirection table as we cannot do
an insertion sort on the afs_callback_break array as we decode FIDs
into it as we subsequently also have to decode callback info into it
that corresponds by array index only.
We also don't really want to bubblesort afterwards if we can avoid it.
(2) Sort the server->cb_interests array by vid so that all the matching
volumes are grouped together. This permits the scan to stop after
finding a record that has a higher vid.
(3) When breaking FIDs, we try to keep server->cb_break_lock as long as
possible, caching the start point in the array for that volume group
as long as possible.
It might make sense to add another layer in that list and have a
refcounted volume ID anchor that has the matching interests attached
to it rather than being in the list. This would allow the lock to be
dropped without losing the cursor.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 15 Jun 2018 14:19:22 +0000 (15:19 +0100)]
afs: Display manually added cells in dynamic root mount
Alter the dynroot mount so that cells created by manipulation of
/proc/fs/afs/cells and /proc/fs/afs/rootcell and by specification of a root
cell as a module parameter will cause directories for those cells to be
created in the dynamic root superblock for the network namespace[*].
To this end:
(1) Only one dynamic root superblock is now created per network namespace
and this is shared between all attempts to mount it. This makes it
easier to find the superblock to modify.
(2) When a dynamic root superblock is created, the list of cells is walked
and directories created for each cell already defined.
(3) When a new cell is added, if a dynamic root superblock exists, a
directory is created for it.
(4) When a cell is destroyed, the directory is removed.
(5) These directories are created by calling lookup_one_len() on the root
dir which automatically creates them if they don't exist.
[*] Inasmuch as network namespaces are currently supported here.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 15 Jun 2018 14:19:10 +0000 (15:19 +0100)]
afs: Enable IPv6 DNS lookups
Remove the restriction on DNS lookup upcalls that prevents ipv6 addresses
from being looked up.
Signed-off-by: David Howells <dhowells@redhat.com>
Anatoliy Glagolev [Wed, 13 Jun 2018 21:38:51 +0000 (15:38 -0600)]
bsg: fix race of bsg_open and bsg_unregister
The existing implementation allows races between bsg_unregister and
bsg_open paths. bsg_unregister and request_queue cleanup and deletion
may start and complete right after bsg_get_device (in bsg_open path)
retrieves bsg_class_device and releases the mutex. Then bsg_open path
touches freed memory of bsg_class_device and request_queue.
One possible fix is to hold the mutex all the way through bsg_get_device
instead of releasing it after bsg_class_device retrieval.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-Off-By: Anatoliy Glagolev <glagolig@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Christoph Hellwig [Fri, 15 Jun 2018 11:55:07 +0000 (13:55 +0200)]
block: remov blk_queue_invalidate_tags
This function is entirely unused, so remove it and the tag_queue_busy
member of struct request_queue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Fri, 15 Jun 2018 14:11:05 +0000 (08:11 -0600)]
Merge branch 'nvme-4.18' of git://git.infradead.org/nvme into for-linus
Pull NVMe fixes from Christoph:
"Fix various little regressions introduced in this merge window, plus
a rework of the fibre channel connect and reconnect path to share the
code instead of having separate sets of bugs. Last but not least a
trivial trace point addition from Hannes."
* 'nvme-4.18' of git://git.infradead.org/nvme:
nvme-fabrics: fix and refine state checks in __nvmf_check_ready
nvme-fabrics: handle the admin-only case properly in nvmf_check_ready
nvme-fabrics: refactor queue ready check
blk-mq: remove blk_mq_tagset_iter
nvme: remove nvme_reinit_tagset
nvme-fc: fix nulling of queue data on reconnect
nvme-fc: remove reinit_request routine
nvme-fc: change controllers first connect to use reconnect path
nvme: don't rely on the changed namespace list log
nvmet: free smart-log buffer after use
nvme-rdma: fix error flow during mapping request data
nvme: add bio remapping tracepoint
nvme: fix NULL pointer dereference in nvme_init_subsystem
Dedy Lansky [Fri, 15 Jun 2018 11:05:01 +0000 (13:05 +0200)]
cfg80211: fix rcu in cfg80211_unregister_wdev
Callers of cfg80211_unregister_wdev can free the wdev object
immediately after this function returns. This may crash the kernel
because this wdev object is still in use by other threads.
Add synchronize_rcu() after list_del_rcu to make sure wdev object can
be safely freed.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Toke Høiland-Jørgensen [Fri, 25 May 2018 12:29:21 +0000 (14:29 +0200)]
mac80211: Move up init of TXQs
On init, ieee80211_if_add() dumps the interface. Since that now includes a
dump of the TXQ state, we need to initialise that before the dump happens.
So move up the TXQ initialisation to to before the call to
ieee80211_if_add().
Fixes: 52539ca89f36 ("cfg80211: Expose TXQ stats and parameters to userspace")
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
projects / openwrt / staging / blogic.git / log