Merge branch 'for-davem' of git://git./linux/kernel/git/linville/wireless-next-2.6

Revert "tc35815: fix iomap leak"

This reverts commit b31fb86815153be3bc94e8ffb9dbf6e9d7694b2d.

pcim_*() managed drivers do not need explicit resource
releasing like this.

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6 into for-davem

Conflicts:
drivers/net/wireless/wl12xx/wl1271_cmd.h

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

drivers/net: Add Micrel KS8841/42 support to ks8842 driver

Body of the explanation:
   -support 16bit and 32bit bus width.
   -add device reset for ks8842/8841 Micrel device.
   -set 100Mbps as a default for Micrel device.
   -set MAC address in both MAC/Switch layer with different sequence for Micrel
    device, as mentioned in data sheet.
   -use private data to set options both 16/32bit bus width and Micrel device/
    Timberdale(FPGA).
   -update Kconfig in order to put more information about ks8842 device.

Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hso: remove driver version

This patch removes the driver version from the driver. This version
hasn't changed since the driver's inclusion in the kernel and is a
source of confusion for some customers.

Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/irda: Remove unnecessary casts of private_data

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/core: Remove unnecessary casts of private_data

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/caif: Remove unnecessary casts of private_data

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/isdn: Remove unnecessary casts of private_data

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm: remove IRQF_DISABLED in combination with IRQF_SHARED

Signed-off-by: Chas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>

fec: use interrupt for MDIO completion indication

With the move to phylib (commit e6b043d) I was seeing sporadic "MDIO write
timeout" messages. Measure of the actual time spent showed latency times of
more than 1600us.

This patch uses the MII event indication of the FEC hardware to detect
completion of MDIO transactions.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: autoconvert trivial BKL users to private mutex

All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.

None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.

Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.

file=$1
name=$2
if grep -q lock_kernel ${file} ; then
    if grep -q 'include.*linux.mutex.h' ${file} ; then
            sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
    else
            sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
    fi
    sed -i ${file} \
        -e "/^#include.*linux.mutex.h/,$ {
                1,/^\(static\|int\|long\)/ {
                     /^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);

} }"  \
    -e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
    -e '/[      ]*cycle_kernel_lock();/d'
else
    sed -i -e '/include.*\<smp_lock.h\>/d' ${file}  \
                -e '/cycle_kernel_lock()/d'
fi

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn: autoconvert trivial BKL users to private mutex

All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.

None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.

Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.

file=$1
name=$2
if grep -q lock_kernel ${file} ; then
    if grep -q 'include.*linux.mutex.h' ${file} ; then
            sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
    else
            sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
    fi
    sed -i ${file} \
        -e "/^#include.*linux.mutex.h/,$ {
                1,/^\(static\|int\|long\)/ {
                     /^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);

} }"  \
    -e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
    -e '/[      ]*cycle_kernel_lock();/d'
else
    sed -i -e '/include.*\<smp_lock.h\>/d' ${file}  \
                -e '/cycle_kernel_lock()/d'
fi

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sock_free() optimizations

Avoid two extra instructions in sock_free(), to reload
skb->truesize and skb->sk

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inet, inet6: make tcp_sendmsg() and tcp_sendpage() through inet_sendmsg() and inet_sendpage()

a new boolean flag no_autobind is added to structure proto to avoid the autobind
calls when the protocol is TCP. Then sock_rps_record_flow() is called int the
TCP's sendmsg() and sendpage() pathes.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
 include/net/inet_common.h |    4 ++++
 include/net/sock.h        |    1 +
 include/net/tcp.h         |    8 ++++----
 net/ipv4/af_inet.c        |   15 +++++++++------
 net/ipv4/tcp.c            |   11 +++++------
 net/ipv4/tcp_ipv4.c       |    3 +++
 net/ipv6/af_inet6.c       |    8 ++++----
 net/ipv6/tcp_ipv6.c       |    3 +++
 8 files changed, 33 insertions(+), 20 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>

net: cleanups

remove useless blanks.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
 include/net/inet_common.h |   55 ++++-------
 include/net/tcp.h         |  222 +++++++++++++++++-----------------------------
 include/net/udp.h         |   38 +++----
 3 files changed, 123 insertions(+), 192 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>

xtsonic: free irq if sonic_open() fails

xtsonic_open() doesn't check sonic_open() return code. If it is error
we must free requested IRQ.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

macsonic: free irqs if sonic_open() fails

macsonic_open() doesn't check sonic_open() return code. If it is error
we must free requested IRQs.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

jazzsonic: free irq if sonic_open() fails

jazzsonic_open() doesn't check sonic_open() return code. If it is error
we must free requested IRQ.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn: fix strlen() usage

There was a missing "else" statement so the original code overflowed if
->master->name was too long.  Also the ->slave and ->master buffers can
hold names with 9 characters and a NULL so I cleaned it up to allow
another character.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9p: strlen() doesn't count the terminator

This is an off by one bug because strlen() doesn't count the NULL
terminator.  We strcpy() addr into a fixed length array of size
UNIX_PATH_MAX later on.

The addr variable is the name of the device being mounted.

CC: stable@kernel.org
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tc35815: fix iomap leak

If tc35815_init_one() fails we must unmap mapped regions.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ll_temac: Fix missing validate_addr hook

Fix missing validate_addr hook

Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4vf: fix TX Queue restart

Fix up TX Queue Host Flow Control to cause an Egress Queue Status Update to
be generated when we run out of TX Queue Descriptors.  This will, in turn,
allow us to restart a stopped TX Queue.

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

depca: fix leaks in depca_module_init()

Since some of xxx_register_driver() can return error we must unregister
already registered drivers.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

p54: update MAINTAINERS

Michael has been out of the scene for a while now,
but despite Michael's absence, p54 is still maintained.

Cc: Michael Wu <aluminum.tape@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: merge noisefloor load implementations

AR5008+ and AR9003 currently use two separate implementations of the
ath9k_hw_loadnf function. There are three main differences:

 - PHY registers for AR9003 are different
 - AR9003 always uses 3 chains, earlier versions are more selective
 - The AR9003 variant contains a fix for NF load timeouts

This patch merges the two implementations into one, storing the
register array in the ath_hw struct. The fix for NF load timeouts is
not just relevant for AR9003, but also important for earlier hardware,
so it's better to just keep one common implementation.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: validate the TID in the tx status information

Occasionally the hardware can send out tx status information with the wrong
TID. In that case, the BA status cannot be trusted and the aggregate
must be retransmitted.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: report the TID in the tx status on AR5008-AR9002

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: prevent a fast channel change after a rx DMA stuck issue

If the receive path gets stuck, a full hardware reset is necessary to
recover from it. If this happens during a scan, the whole scan might fail,
as each channel change bypasses the full reset sequence.
Fix this by resetting the fast channel change flag if stopping the
receive path fails.

This will reduce the number of error messages that look like this:
ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x40000020

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix an off-by-one error in the PDADC boundaries calculation

PDADC values were only generated for values surrounding the target
index, however not for the target index itself, leading to a minor
error in the generated curve.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix a sign error in the IQ calibration code

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix antenna diversity on AR9285

On AR9285, the antenna switch configuration register uses more than just
16 bits. Because of an arbitrary mask applied to the EEPROM value that
stores this configuration, diversity was broken in some cases, leading
to a significant degradation in signal strength.
Fix this by changing the callback to return a 32 bit value and remove
the arbitrary mask.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Move driver callback functions into the ops structure

All callback functions are gathered in rt2x00dev->ops except
for the callback functions which are used in rt2800lib to
acces rt2800pci/usb.

Move the priv pointer from rt2x00dev to rt2x00dev->ops and
rename it to drv to make it obvious that it is the driver callback
structure.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Move common firmware loading into rt2800lib

Large parts of the firmware initialization are shared
between rt2800pci and rt2800usb. Move this code into
rt2800lib.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add missing TSF sync mode for AP operation

Currently rt2x00 uses the TSF_SYNC_BEACON mode for all beaconing
interface types. However, TSF_SYNC_BEACON is meant for IBSS networks and
thus implements TSF merging in the hardware. Rename TSF_SYNC_BEACON to
TSF_SYNC_ADHOC to better express its purpose and introduce the missing
TSF sync mode TSF_SYNC_AP_NONE which should be used for beaconing modes
that don't need TSF merging.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Don't initialize beacon interval to 0 on rt2800 devices

Activating the TBTT interrupt when a beacon interval of 0 is configured
results in an interrupt storm causing the machine to hang. Hence,
initialize the beacon interval to a reasonable default of 100TUs.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Remove set_tim callback from PCI drivers

Using the set_tim callback without managing the DTIM count and the
broad- and multicast buffering in hw, fw or the driver results in wrong
DTIM count values being sent out in beacons. Since all PCI drivers
fetch new beacons periodically and hence get an updated TIM we can just
remove the set_tim callback from these.

The rt2x00 USB drivers don't update the beacon periodically and thus
rely on the set_tim callback to get a correct TIM for beacon
transmission. USB devices still suffer from the DTIM count being wrong
under some circumstances but removing the set_tim callback from these
would cause more harm then good.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Use separate mac80211_ops for rt2800pci and rt2800usb

Use separate mac80211_ops for rt2800pci and rt2800usb in preparation
for further fixes. This shouldn't introduce functional changes.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Use pretbtt irq for fetching beacons on rt2800pci

Updating the beacon on pre tbtt instead of beacondone allows much lower
latency in regard to TIM updates. Hence, use the pre tbtt interrupt for
updating the beacon in rt2800pci (older devices don't provide a pre tbtt
interrupt).

Also, add a new driver flag to indicate if a driver has pre tbtt support
or not and implement the according behavior in rt2x00lib.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Implement broad- and multicast buffering

Although mac80211 buffers broad- and mutlicast frames for us in AP mode
we still have to send them out after a DTIM beacon. Implement this
behavior by sending out the buffered frames when the beacondone
interrupt is processed.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Allow beacon update without scheduling a work

Since all rt2x00 PCI drivers use threaded interrupts now we don't need
to schedule a work just to update the beacon. The only place where the
beacon still gets updated in atomic context is from the set_tim
callback. Hence, move the work scheduling there.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Convert rt2x00 to use threaded interrupts

Use threaded interrupts for all rt2x00 PCI devices.

This has several generic advantages:
- Reduce the time we spend in hard irq context
- Use non-atmic mac80211 functions for rx/tx

Furthermore implementing broad- and multicast buffering will be
much easier in process context while maintaining low latency and
updating the beacon just before transmission (pre tbtt interrupt)
can also be done in process context.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Make rt2800_write_beacon only export to GPL

rt2800_write_beacon is the only function which uses
EXPORT_SYMBOL instead of EXPORT_SYMBOL_GPL. All symbols
in rt2x00 should however use the GPL restricted export.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Implement watchdog monitoring

Implement watchdog monitoring for USB devices (PCI support can
be added later). This will determine if URBs being uploaded to
the hardware are actually returning. Both rt2500usb and rt2800usb
have shown that URBs being uploaded can remain hanging without
being released by the hardware.
By using this watchdog, a queue can be reset when this occurs.
For rt2800usb it has been tested that the connection is preserved
even though this interruption.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix vgc_level_reg handling

Currently vgc_level_reg and vgc_level are equal to eachother,
while the purpose of vgc_level_reg is the value last written
to the register and is remembered through link tuning resets.
The vgc_level is the currently active level, which is
reset during link tuning resets.

The usage of these variables depends on the drivers, some drivers
need both, while others need only one of the two.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Disable link tuning while scanning

While scanning the link tuner must be disabled. Otherwise
it will interfere with receiving all beacons for each channel
due to changing sensitivity levels.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Rename CONFIG_DISABLE_LINK_TUNING

Rename CONFIG_DISABLE_LINK_TUNING to DRIVER_SUPPORT_LINK_TUNING
Link tuning support is not only based on EEPROM decisions, but
also if the device actually supports it.

Currently only rt2500usb doesn't support link tuning because
of hardware problems. But rt2800usb is also suspected of having
problems with link tuning.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Convert AGC value from descriptor to RSSI (dBm)

The RSSI values in the RXWI descriptor aren't true RSSI
values. Instead they are more like the AGC values similar
to rt61pci. And as such, it needs the same conversion
before it can be passed to rt2x00lib/mac80211.

This requires the struct queue_entry to be passed to
rt2800_process_rxwi rather then the skb structure which
is contained in the queue_entry. This is required to
obtain the lna_gain information from the rt2x00_dev structure.

This fixes connection problems when using wpa_supplicant
which would try to connect to the worst AP's rather then the
best ones.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Limit txpower by eeprom values

Limit the txpower per rate by the approriate values in the eeprom.
This avoids too high txpower values resulting in bad tx performance.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

hostap: fixup strlen() math

In hostap_add_interface() we do:
sprintf(dev->name, "%s%s", prefix, name);

dev->name has IFNAMSIZ (16) characters.
prefix is local->dev->name.
name is "wds%d"

strlen() returns the number of characters in the string not counting the
NULL so if we have a string with 11 characters we get "12345678901wds%d"
which is 16 characters and a NULL so we're past the end of the array.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

adm8211: fix memory leak

We must free priv->eeprom allocated in adm8211_read_eeprom().

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

prism54: call BUG_ON() earlier

This test is off by one because strlen() doesn't include the NULL
terminator.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271: use __packed annotation

This patch changes __attribute__ ((packed)) annotations to __packed in wl1271
code that was introduced in a recent patch in wireless-testing.

Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: Added support for host sleep feature

Existing "ethtool -s ethX wol X" command configures hostsleep
parameters, but those are activated only during suspend/resume,
there is no way to configure host sleep without actual suspend.

This patch adds debugfs command to enable/disable host sleep based on
already configured host sleep parameters using wol command.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: ignore spurious deauth

Ever since mac80211/drivers are no longer
fully in charge of keeping track of the
auth status, trying to make them do so will
fail. Instead of warning and reporting the
deauthentication to userspace, cfg80211 must
simply ignore it so that spurious
deauthentications, e.g. before starting
authentication, aren't seen by userspace as
actual deauthentications.

Cc: stable@kernel.org
Reported-by: Paul Stewart <pstew@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

MAINTAINERS: mark adm8211 as an orphan

Signed-off-by: John W. Linville <linville@tuxdriver.com>

net/core: EXPORT_SYMBOL cleanups

CodingStyle cleanups

EXPORT_SYMBOL should immediately follow the symbol declaration.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/ipv4: EXPORT_SYMBOL cleanups

CodingStyle cleanups

EXPORT_SYMBOL should immediately follow the symbol declaration.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ac3200: fix error path

Do not call free_irq() if request_irq() failed.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

at1700: fix double free_irq

free_irq() is called both in net_close() and cleanup_card().  Since it
is requested in at1700_probe1(), leave free_irq() only in cleanup_card()
for balance.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: exclude registers with read side effects from register dumps

A few registers have side effects on reads, eg FIFO pointers that
auto advance or mailboxes which change ownership when read.  They are
unsafe to read so exclude them from ethtool register dumps.

Bump ethtool_regs.version to indicate the changed register set.

Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: implement the ETHTOOL_GRXFH command

Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: add user manipulation of the RSS table

Implement the get_rxnfc, get_rxfh_indir, and set_rxfh_indir ethtool
methods for user manipulation of the RSS table.  Besides the methods
themselves the rest of the changes here store, initialize, and write
the table contents.

Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: avoid duplicating some resource freeing code

Currently there are two copies of some resource freeing code, turn it into
a function and call it.

Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: move the choice of interrupt type before net_device registration

We need to settle on the kind of interrupts we'll be using, a choice that
also impacts the number of queues, before registering and making visible
the net_devices.  Move the relevant code up a bit.

Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Update version to 3.112

This patch updates the tg3 version to 3.112.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Fix some checkpatch errors

This patch fixes the following checkpatch errors:

ERROR: do not use assignment in if condition
+ if ((mss = skb_shinfo(skb)->gso_size) != 0) {

ERROR: do not use assignment in if condition
+ if ((mss = skb_shinfo(skb)->gso_size) != 0) {

ERROR: space prohibited after that '!' (ctx:BxW)
+ if (! netif_carrier_ok(tp->dev) &&
      ^

ERROR: space required after that ',' (ctx:VxV)
+#define GET_REG32_LOOP(base,len) \
                            ^

ERROR: "(foo*)" should be "(foo *)"
+ memcpy(data, ((char*)&val) + b_offset, b_count);

ERROR: do not use assignment in if condition
+ if ((err = tg3_do_mem_test(tp, mem_tbl[i].offset,

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Revert PCIe tx glitch fix

This patch reverts commit 52cdf8526fe24f11d300b75458ddee017f3f4c88,
entitled "tg3: Prevent a PCIe tx glitch".  The problem does not have
any visible side-effects and happens too early for the driver to do
anything about it.  The proper place for this code is within the
device's bootcode.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Report driver version to firmware

This patch changes the code so that the driver version can be reported
to the firmware in addition to the current use.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Relax 5717 serdes restriction

tg3 is coded to refuse to attach to 5717 serdes devices.  Now that the
hardware is better supported, we can relax this restriction.  This patch
also fixes a recently introduced bug which will cause serdes parallel
detection not to work with 5780 class devices.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Fix IPv6 TSO code in tg3_start_xmit_dma_bug()

The tg3_start_xmit_dma_bug() function was missing code to process IPv6
TSO packets.  This patch adds the missing support.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Fix single MSI-X vector coalescing

The interrupt coalescing setup code used the TG3_FLG2_USING_MSIX flag to
determine whether or not to configure the rx coalescing parameters.
This is incorrect for the single MSI-X vector case.  This patch changes
the code to look at the TG3_FLG3_ENABLE_RSS instead.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Revert RSS indir tbl setup change

This patch reverts commit 2601d8a0049c8b5d29cd5adb844a305a804e505f.  A
spectacular set of coincidences made it look as though the table was
setup incorrectly.  The original version was correct.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

82596: free resources on error

IRQ 56 was not freed anywhere (neither in i596_open() on error nor in
i596_close()), rx_bufs were not freed if init_i596_mem() fails,
netif_stop_queue() was not called.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

82596: do not panic on out of memory

If dev_alloc_skb() failed then free already allocated skbs.
remove_rx_bufs() can be called multiple times, so set rbd->skb to NULL
to avoid double free. remove_rx_bufs() was moved upwards to be seen by
init_rx_bufs().

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Patch to determine if function is VF while running in guest OS.

When driver is loaded in guest OS, the pci variables is_virtfn and is_physfn are
both set to 0. This change uses registers in controller to determine the same.

Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

macvtap: Use dev_t for macvtap_major.

Reported-by: "Robert P. J. Day" <rpjday@crashcourse.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: Disable admin tools interface for VF driver mode

Non privileged (VF) driver will not be able to carry out any of the FW update,
etc. operations. Disable the tools interface by not creating the sysfs nodes.

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: Check FW capability for TSO

Driver checks TSO capability from FW before enabling it.

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Document that dev_get_stats() returns the given pointer

Document that dev_get_stats() returns the same stats pointer it was
given.  Remove const qualification from the returned pointer since the
caller may do what it likes with that structure.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Get rid of rtnl_link_stats64 / net_device_stats union

In commit be1f3c2c027cc5ad735df6a45a542ed1db7ec48b "net: Enable 64-bit
net device statistics on 32-bit architectures" I redefined struct
net_device_stats so that it could be used in a union with struct
rtnl_link_stats64, avoiding the need for explicit copying or
conversion between the two.  However, this is unsafe because there is
no locking required and no lock consistently held around calls to
dev_get_stats() and use of the statistics structure it returns.

In commit 28172739f0a276eb8d6ca917b3974c2edb036da3 "net: fix 64 bit
counters on 32 bit arches" Eric Dumazet dealt with that problem by
requiring callers of dev_get_stats() to provide storage for the
result.  This means that the net_device::stats64 field and the padding
in struct net_device_stats are now redundant, so remove them.

Update the comment on net_device_ops::ndo_get_stats64 to reflect its
new usage.

Change dev_txq_stats_fold() to use struct rtnl_link_stats64, since
that is what all its callers are really using and it is no longer
going to be compatible with struct net_device_stats.

Eric Dumazet suggested the separate function for the structure
conversion.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

iwlagn: fix the bit mask of a FH register in stop Tx DMA flow

When we stop the Tx DMA channels, we poll bits 16:31 in
FH_TSSR_RX_STATUS_REG. From 4965 and up, only the bits 16:26 are legal.
Bits 27:31 are not used and are always unset.
Polling them will lead to fail on timeout but since the timeout is quite
small, the stall was not felt.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: more generic description for iwlagn devices

Intel Wireless WiFi Next Gen AGN support two major categories:
 1. Intel Wireless WiFi 4965 AGN device
 2. Intel Wireless-N/Advanced-N/Ultimate-N family

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: correct descriptions of advanced ucode errors

ucode errors were redefined in new ucode images and all new errors
were showing as advanced sysasserts which was misleading. new errors
are not sequential so additional lookup table added.  errors do not
overlap so both are used to support older and newer ucode images.

Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: enable 6050 series Gen2 devices

To enable 6050 series Gen 2 devices:
1) new PCI_IDs are added;
2) new EEPROM version and calibration version numbers defined;
3) new hardware REV number defined;

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

usb/atm/ueagle-atm.c: call atm_dev_signal_change() when signal changes.

Propagate signal changes to upper atm layer.

Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

usb/atm/speedtch.c: call atm_dev_signal_change() when signal changes.

Propagate signal changes to upper atm layer.

Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

usb/atm/cxacru.c: call atm_dev_signal_change() when signal changes.

Propagate signal changes to upper atm layer.

Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm/suni.c: call atm_dev_signal_change() when signal changes.

Propagate changes to upper atm layer.

Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm/solos-pci: call atm_dev_signal_change() when signal changes.

Propagate changes to upper atm layer, so userspace netmontor knows when DSL
showtime reached.

Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm/idt77105.c: call atm_dev_signal_change() when signal changes.

Propagate changes to upper atm layer.

Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm/adummy: add syfs DEVICE_ATTR to change signal

Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm/br2684: register notifier event for carrier signal changes.

When a signal change event occurs call netif_carrier_on/off.

Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm: propagate signal changes via notifier

Add notifier chain for changes in atm_dev.

Clients like br2684 will call register_atmdevice_notifier() to be notified of
changes. Drivers will call atm_dev_signal_change() to notify clients like
br2684 of the change.

On DSL and ATM devices it's usefull to have a know if you have a carrier
signal. netdevice LOWER_UP changes can be propagated to userspace via netlink
monitor.

Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4vf: Implement "Unhandled Interrupts" statistic

Implement "Unhandled Interrupts" statistic so we can detect when the
hardware tells us that it things we have work to do but we don't find
anything ...

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fec_mpc52xx: fix error path

Error path in mpc52xx_fec_probe() is broken.
We must free everything that we've allocated.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ll_temac: fix memory leak

If of_iomap() or irq_of_parse_and_map() fail then np must be freed.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ax88796: free irq on error

If ax_ei_open() failed we must free previously requested irq.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>