From 022e4e52a750066047b22031733df70e136ae299 Mon Sep 17 00:00:00 2001 From: Sunil Kamath Date: Wed, 30 Sep 2015 22:34:57 +0530 Subject: [PATCH] drm/i915/bxt: Modify BXT BLC according to VBT changes Latest VBT mentions which set of registers will be used for BLC, as controller number field. Making use of this field in BXT BLC implementation. Also, the registers are used in case control pin indicates display DDI. Adding a check for this. According to Bspec, BLC_PWM_*_2 uses the display utility pin for output. To use backlight 2, enable the utility pin with mode = PWM v2: Jani's review comments addressed - Add a prefix _ to BXT BLC registers definitions. - Add "bxt only" comment for u8 controller - Remove control_pin check for DDI controller - Check for valid controller values - Set pipe bits in UTIL_PIN_CTL - Enable/Disable UTIL_PIN_CTL in enable/disable_backlight() - If BLC 2 is used, read active_low_pwm from UTIL_PIN polarity Satheesh's review comment addressed - If UTIL PIN is already enabled, BIOS would have programmed it. No need to disable and enable again. v3: Jani's review comments - add UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK - Disable UTIL_PIN if controller 1 is used - Mask out UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK before enabling UTIL_PIN - check valid controller value in intel_bios.c - add backlight.util_pin_active_low - disable util pin before enabling v4: Change for BXT-PO branch: Stubbed unwanted definition which was existing before because of DC6 patch. UTIL_PIN_MODE_PWM (0x1b << 24) v2: Fixed Jani's review comment. v3: Split the backight PWM frequency programming into separate patch, in cases BIOS doesn't initializes it. v4: Starting afresh and not modifying existing state for backlight, as per Jani's recommendation. v5: Fixed Jani's review comment wrt util pin enable Signed-off-by: Vandana Kannan Signed-off-by: Sunil Kamath Signed-off-by: Uma Shankar Reviewed-by: Jani Nikula Signed-off-by: Daniel Vetter --- drivers/gpu/drm/i915/i915_reg.h | 28 ++++++++--- drivers/gpu/drm/i915/intel_drv.h | 2 + drivers/gpu/drm/i915/intel_panel.c | 81 ++++++++++++++++++++++++------ 3 files changed, 88 insertions(+), 23 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 8c24851b930c..8d7be66d96bc 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -3627,17 +3627,29 @@ enum skl_disp_power_wells { #define UTIL_PIN_CTL 0x48400 #define UTIL_PIN_ENABLE (1 << 31) +#define UTIL_PIN_PIPE(x) ((x) << 29) +#define UTIL_PIN_PIPE_MASK (3 << 29) +#define UTIL_PIN_MODE_PWM (1 << 24) +#define UTIL_PIN_MODE_MASK (0xf << 24) +#define UTIL_PIN_POLARITY (1 << 22) + /* BXT backlight register definition. */ -#define BXT_BLC_PWM_CTL1 0xC8250 +#define _BXT_BLC_PWM_CTL1 0xC8250 #define BXT_BLC_PWM_ENABLE (1 << 31) #define BXT_BLC_PWM_POLARITY (1 << 29) -#define BXT_BLC_PWM_FREQ1 0xC8254 -#define BXT_BLC_PWM_DUTY1 0xC8258 - -#define BXT_BLC_PWM_CTL2 0xC8350 -#define BXT_BLC_PWM_FREQ2 0xC8354 -#define BXT_BLC_PWM_DUTY2 0xC8358 - +#define _BXT_BLC_PWM_FREQ1 0xC8254 +#define _BXT_BLC_PWM_DUTY1 0xC8258 + +#define _BXT_BLC_PWM_CTL2 0xC8350 +#define _BXT_BLC_PWM_FREQ2 0xC8354 +#define _BXT_BLC_PWM_DUTY2 0xC8358 + +#define BXT_BLC_PWM_CTL(controller) _PIPE(controller, \ + _BXT_BLC_PWM_CTL1, _BXT_BLC_PWM_CTL2) +#define BXT_BLC_PWM_FREQ(controller) _PIPE(controller, \ + _BXT_BLC_PWM_FREQ1, _BXT_BLC_PWM_FREQ2) +#define BXT_BLC_PWM_DUTY(controller) _PIPE(controller, \ + _BXT_BLC_PWM_DUTY1, _BXT_BLC_PWM_DUTY2) #define PCH_GTC_CTL 0xe7000 #define PCH_GTC_ENABLE (1 << 31) diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h index dfd2d10d3d3c..563c4f1e3685 100644 --- a/drivers/gpu/drm/i915/intel_drv.h +++ b/drivers/gpu/drm/i915/intel_drv.h @@ -179,6 +179,8 @@ struct intel_panel { bool active_low_pwm; /* PWM chip */ + bool util_pin_active_low; /* bxt+ */ + u8 controller; /* bxt+ only */ struct pwm_device *pwm; struct backlight_device *device; diff --git a/drivers/gpu/drm/i915/intel_panel.c b/drivers/gpu/drm/i915/intel_panel.c index 4d28c7b904e7..f30c996e882c 100644 --- a/drivers/gpu/drm/i915/intel_panel.c +++ b/drivers/gpu/drm/i915/intel_panel.c @@ -536,9 +536,10 @@ static u32 vlv_get_backlight(struct intel_connector *connector) static u32 bxt_get_backlight(struct intel_connector *connector) { struct drm_device *dev = connector->base.dev; + struct intel_panel *panel = &connector->panel; struct drm_i915_private *dev_priv = dev->dev_private; - return I915_READ(BXT_BLC_PWM_DUTY1); + return I915_READ(BXT_BLC_PWM_DUTY(panel->backlight.controller)); } static u32 pwm_get_backlight(struct intel_connector *connector) @@ -634,8 +635,9 @@ static void bxt_set_backlight(struct intel_connector *connector, u32 level) { struct drm_device *dev = connector->base.dev; struct drm_i915_private *dev_priv = dev->dev_private; + struct intel_panel *panel = &connector->panel; - I915_WRITE(BXT_BLC_PWM_DUTY1, level); + I915_WRITE(BXT_BLC_PWM_DUTY(panel->backlight.controller), level); } static void pwm_set_backlight(struct intel_connector *connector, u32 level) @@ -786,12 +788,20 @@ static void bxt_disable_backlight(struct intel_connector *connector) { struct drm_device *dev = connector->base.dev; struct drm_i915_private *dev_priv = dev->dev_private; - u32 tmp; + struct intel_panel *panel = &connector->panel; + u32 tmp, val; intel_panel_actually_set_backlight(connector, 0); - tmp = I915_READ(BXT_BLC_PWM_CTL1); - I915_WRITE(BXT_BLC_PWM_CTL1, tmp & ~BXT_BLC_PWM_ENABLE); + tmp = I915_READ(BXT_BLC_PWM_CTL(panel->backlight.controller)); + I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller), + tmp & ~BXT_BLC_PWM_ENABLE); + + if (panel->backlight.controller == 1) { + val = I915_READ(UTIL_PIN_CTL); + val &= ~UTIL_PIN_ENABLE; + I915_WRITE(UTIL_PIN_CTL, val); + } } static void pwm_disable_backlight(struct intel_connector *connector) @@ -1023,16 +1033,38 @@ static void bxt_enable_backlight(struct intel_connector *connector) struct drm_device *dev = connector->base.dev; struct drm_i915_private *dev_priv = dev->dev_private; struct intel_panel *panel = &connector->panel; - u32 pwm_ctl; + enum pipe pipe = intel_get_pipe_from_connector(connector); + u32 pwm_ctl, val; + + /* To use 2nd set of backlight registers, utility pin has to be + * enabled with PWM mode. + * The field should only be changed when the utility pin is disabled + */ + if (panel->backlight.controller == 1) { + val = I915_READ(UTIL_PIN_CTL); + if (val & UTIL_PIN_ENABLE) { + DRM_DEBUG_KMS("util pin already enabled\n"); + val &= ~UTIL_PIN_ENABLE; + I915_WRITE(UTIL_PIN_CTL, val); + } - pwm_ctl = I915_READ(BXT_BLC_PWM_CTL1); + val = 0; + if (panel->backlight.util_pin_active_low) + val |= UTIL_PIN_POLARITY; + I915_WRITE(UTIL_PIN_CTL, val | UTIL_PIN_PIPE(pipe) | + UTIL_PIN_MODE_PWM | UTIL_PIN_ENABLE); + } + + pwm_ctl = I915_READ(BXT_BLC_PWM_CTL(panel->backlight.controller)); if (pwm_ctl & BXT_BLC_PWM_ENABLE) { DRM_DEBUG_KMS("backlight already enabled\n"); pwm_ctl &= ~BXT_BLC_PWM_ENABLE; - I915_WRITE(BXT_BLC_PWM_CTL1, pwm_ctl); + I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller), + pwm_ctl); } - I915_WRITE(BXT_BLC_PWM_FREQ1, panel->backlight.max); + I915_WRITE(BXT_BLC_PWM_FREQ(panel->backlight.controller), + panel->backlight.max); intel_panel_actually_set_backlight(connector, panel->backlight.level); @@ -1040,9 +1072,10 @@ static void bxt_enable_backlight(struct intel_connector *connector) if (panel->backlight.active_low_pwm) pwm_ctl |= BXT_BLC_PWM_POLARITY; - I915_WRITE(BXT_BLC_PWM_CTL1, pwm_ctl); - POSTING_READ(BXT_BLC_PWM_CTL1); - I915_WRITE(BXT_BLC_PWM_CTL1, pwm_ctl | BXT_BLC_PWM_ENABLE); + I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller), pwm_ctl); + POSTING_READ(BXT_BLC_PWM_CTL(panel->backlight.controller)); + I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller), + pwm_ctl | BXT_BLC_PWM_ENABLE); } static void pwm_enable_backlight(struct intel_connector *connector) @@ -1562,10 +1595,28 @@ bxt_setup_backlight(struct intel_connector *connector, enum pipe unused) struct intel_panel *panel = &connector->panel; u32 pwm_ctl, val; - pwm_ctl = I915_READ(BXT_BLC_PWM_CTL1); - panel->backlight.active_low_pwm = pwm_ctl & BXT_BLC_PWM_POLARITY; + /* + * For BXT hard coding the Backlight controller to 0. + * TODO : Read the controller value from VBT and generalize + */ + panel->backlight.controller = 0; - panel->backlight.max = I915_READ(BXT_BLC_PWM_FREQ1); + pwm_ctl = I915_READ(BXT_BLC_PWM_CTL(panel->backlight.controller)); + + /* Keeping the check if controller 1 is to be programmed. + * This will come into affect once the VBT parsing + * is fixed for controller selection, and controller 1 is used + * for a prticular display configuration. + */ + if (panel->backlight.controller == 1) { + val = I915_READ(UTIL_PIN_CTL); + panel->backlight.util_pin_active_low = + val & UTIL_PIN_POLARITY; + } + + panel->backlight.active_low_pwm = pwm_ctl & BXT_BLC_PWM_POLARITY; + panel->backlight.max = + I915_READ(BXT_BLC_PWM_FREQ(panel->backlight.controller)); if (!panel->backlight.max) panel->backlight.max = get_backlight_max_vbt(connector); -- 2.30.2