From 5163bb5e545eaac30dc5b5a6d75686b26f70667c Mon Sep 17 00:00:00 2001 From: INAGAKI Hiroshi <musashino.open@gmail.com> Date: Mon, 20 Sep 2021 22:28:51 +0900 Subject: [PATCH] realtek: add support for APRESIA ApresiaLightGS120GT-SS MIME-Version: 1.0 Content-Type: text/plain; charset=utf8 Content-Transfer-Encoding: 8bit APRESIA ApresiaLightGS120GT-SS (APLGS120GTSS) is a 16 + 4 ports gigabit switch, based on RTL8382M. Specifications: - SoC : Realtek RTL8382M - RAM : DDR3 256 MiB (Nanya NT5CC256M8JQ-EK) - Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G) - Ethernet : 10/100/1000 Mbps x16 + 4 - port 1-8 : RTL8218B - port 9-16 : RTL8382M, TP (SoC, RTL8218B) - port 17-20 : RTL8214FC, TP/SFP (Combo) - LEDs/Keys : 3x/1x - UART : through-hole on PCB - J6: 3.3V, TX, RX, GND from tri-angle marking side - 115200n8 - Power : 100-120/200-240 VAC, 50/60 Hz Max. 16 W, Avg 14 W (100 VAC) - Plug : IEC 60320-C13 Flash instruction using factory image: 1. Boot ApresiaLightGS120GT-SS normally 2. Login to WebUI and open firmware page ("ãã¡ã¼ã ã¦ã§ã¢") 3. If the device is booted from image1, set active image for next booting ("èµ·åã¤ã¡ã¼ã¸é¸æ") to image2("ã¤ã¡ã¼ã¸2"), press apply ("é©ç¨") button and reboot the device to make booting from image2 4. On the WebUI, set active image to image1 5. Select the OpenWrt factory image and press update button ("æ´æ°") 6. Open reboot page ("åèµ·å") and press reboot button ("åèµ·åå®è¡") Notes: - "ApresiaLightGS120GT-SS" is a model name and "APLGS120GTSS" is a model number - this device has 3x GPIO-controlled LEDs on PCB, but 1x LED ("green:unused") has no hole on the case Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> --- .../dts-5.10/rtl8382_apresia_aplgs120gtss.dts | 270 ++++++++++++++++++ .../dts-5.15/rtl8382_apresia_aplgs120gtss.dts | 270 ++++++++++++++++++ target/linux/realtek/image/rtl838x.mk | 16 ++ 3 files changed, 556 insertions(+) create mode 100644 target/linux/realtek/dts-5.10/rtl8382_apresia_aplgs120gtss.dts create mode 100644 target/linux/realtek/dts-5.15/rtl8382_apresia_aplgs120gtss.dts diff --git a/target/linux/realtek/dts-5.10/rtl8382_apresia_aplgs120gtss.dts b/target/linux/realtek/dts-5.10/rtl8382_apresia_aplgs120gtss.dts new file mode 100644 index 0000000000..15120265c9 --- /dev/null +++ b/target/linux/realtek/dts-5.10/rtl8382_apresia_aplgs120gtss.dts @@ -0,0 +1,270 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "rtl838x.dtsi" + +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> + +/ { + compatible = "apresia,aplgs120gtss", "realtek,rtl8382-soc"; + model = "APRESIA ApresiaLightGS120GT-SS"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x10000000>; + }; + + leds { + compatible = "gpio-leds"; + + led_power: led-0 { + label = "green:pwr"; + gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_POWER; + }; + + led-1 { + label = "red:loop"; + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + color = <LED_COLOR_ID_RED>; + function = LED_FUNCTION_FAULT; + }; + + /* LED chip is soldered, but no hole on the case */ + led-2 { + label = "green:unused"; + gpios = <&gpio1 36 GPIO_ACTIVE_LOW>; + color = <LED_COLOR_ID_GREEN>; + }; + }; + + keys { + compatible = "gpio-keys-polled"; + poll-interval = <20>; + + reset { + label = "reset"; + gpios = <&gpio1 33 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + }; + + gpio-restart { + compatible = "gpio-restart"; + gpios = <&gpio1 34 GPIO_ACTIVE_LOW>; + open-source; + }; + + gpio1: rtl8231-gpio { + compatible = "realtek,rtl8231-gpio"; + #gpio-cells = <2>; + gpio-controller; + indirect-access-bus-id = <0>; + }; + + i2c0: i2c-gpio-0 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio1 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio1 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c1: i2c-gpio-1 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio1 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c2: i2c-gpio-2 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio1 11 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio1 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c3: i2c-gpio-3 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio1 22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + /* 4x TX-Disable lines are provided by RTL8214FC */ + sfp0: sfp-p17 { + compatible = "sff,sfp"; + i2c-bus = <&i2c1>; + los-gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&gpio1 8 GPIO_ACTIVE_LOW>; + }; + + sfp1: sfp-p18 { + compatible = "sff,sfp"; + i2c-bus = <&i2c0>; + los-gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; + }; + + sfp2: sfp-p19 { + compatible = "sff,sfp"; + i2c-bus = <&i2c3>; + los-gpio = <&gpio1 25 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&gpio1 24 GPIO_ACTIVE_LOW>; + }; + + sfp3: sfp-p20 { + compatible = "sff,sfp"; + i2c-bus = <&i2c2>; + los-gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&gpio1 13 GPIO_ACTIVE_LOW>; + }; +}; + +&gpio0 { + rtl8231_reset { + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "rtl8231-reset"; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + label = "u-boot-env"; + reg = <0x80000 0x40000>; + }; + + partition@c0000 { + label = "u-boot-env2"; + reg = <0xc0000 0x40000>; + }; + + partition@100000 { + compatible = "openwrt,uimage", "denx,uimage"; + label = "firmware"; + reg = <0x100000 0xe80000>; + openwrt,ih-magic = <0x12345000>; + }; + + partition@f80000 { + label = "firmware2"; + reg = <0xf80000 0xe80000>; + }; + + partition@1e00000 { + label = "jffs2"; + reg = <0x1e00000 0x200000>; + read-only; + }; + }; + }; +}; + +ðernet0 { + mdio-bus { + compatible = "realtek,rtl838x-mdio"; + regmap = <ðernet0>; + #address-cells = <1>; + #size-cells = <0>; + + EXTERNAL_PHY(0) + EXTERNAL_PHY(1) + EXTERNAL_PHY(2) + EXTERNAL_PHY(3) + EXTERNAL_PHY(4) + EXTERNAL_PHY(5) + EXTERNAL_PHY(6) + EXTERNAL_PHY(7) + + INTERNAL_PHY(8) + INTERNAL_PHY(9) + INTERNAL_PHY(10) + INTERNAL_PHY(11) + INTERNAL_PHY(12) + INTERNAL_PHY(13) + INTERNAL_PHY(14) + INTERNAL_PHY(15) + + EXTERNAL_SFP_PHY_FULL(24, 0) + EXTERNAL_SFP_PHY_FULL(25, 1) + EXTERNAL_SFP_PHY_FULL(26, 2) + EXTERNAL_SFP_PHY_FULL(27, 3) + }; +}; + +&switch0 { + ports { + #address-cells = <1>; + #size-cells = <0>; + + SWITCH_PORT(0, 1, qsgmii) + SWITCH_PORT(1, 2, qsgmii) + SWITCH_PORT(2, 3, qsgmii) + SWITCH_PORT(3, 4, qsgmii) + SWITCH_PORT(4, 5, qsgmii) + SWITCH_PORT(5, 6, qsgmii) + SWITCH_PORT(6, 7, qsgmii) + SWITCH_PORT(7, 8, qsgmii) + + SWITCH_PORT(8, 9, internal) + SWITCH_PORT(9, 10, internal) + SWITCH_PORT(10, 11, internal) + SWITCH_PORT(11, 12, internal) + SWITCH_PORT(12, 13, internal) + SWITCH_PORT(13, 14, internal) + SWITCH_PORT(14, 15, internal) + SWITCH_PORT(15, 16, internal) + + SWITCH_PORT(24, 17, qsgmii) + SWITCH_PORT(25, 18, qsgmii) + SWITCH_PORT(26, 19, qsgmii) + SWITCH_PORT(27, 20, qsgmii) + + port@28 { + ethernet = <ðernet0>; + reg = <28>; + phy-mode = "internal"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; +}; diff --git a/target/linux/realtek/dts-5.15/rtl8382_apresia_aplgs120gtss.dts b/target/linux/realtek/dts-5.15/rtl8382_apresia_aplgs120gtss.dts new file mode 100644 index 0000000000..15120265c9 --- /dev/null +++ b/target/linux/realtek/dts-5.15/rtl8382_apresia_aplgs120gtss.dts @@ -0,0 +1,270 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "rtl838x.dtsi" + +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> + +/ { + compatible = "apresia,aplgs120gtss", "realtek,rtl8382-soc"; + model = "APRESIA ApresiaLightGS120GT-SS"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x10000000>; + }; + + leds { + compatible = "gpio-leds"; + + led_power: led-0 { + label = "green:pwr"; + gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_POWER; + }; + + led-1 { + label = "red:loop"; + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + color = <LED_COLOR_ID_RED>; + function = LED_FUNCTION_FAULT; + }; + + /* LED chip is soldered, but no hole on the case */ + led-2 { + label = "green:unused"; + gpios = <&gpio1 36 GPIO_ACTIVE_LOW>; + color = <LED_COLOR_ID_GREEN>; + }; + }; + + keys { + compatible = "gpio-keys-polled"; + poll-interval = <20>; + + reset { + label = "reset"; + gpios = <&gpio1 33 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + }; + + gpio-restart { + compatible = "gpio-restart"; + gpios = <&gpio1 34 GPIO_ACTIVE_LOW>; + open-source; + }; + + gpio1: rtl8231-gpio { + compatible = "realtek,rtl8231-gpio"; + #gpio-cells = <2>; + gpio-controller; + indirect-access-bus-id = <0>; + }; + + i2c0: i2c-gpio-0 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio1 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio1 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c1: i2c-gpio-1 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio1 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c2: i2c-gpio-2 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio1 11 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio1 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c3: i2c-gpio-3 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio1 22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + /* 4x TX-Disable lines are provided by RTL8214FC */ + sfp0: sfp-p17 { + compatible = "sff,sfp"; + i2c-bus = <&i2c1>; + los-gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&gpio1 8 GPIO_ACTIVE_LOW>; + }; + + sfp1: sfp-p18 { + compatible = "sff,sfp"; + i2c-bus = <&i2c0>; + los-gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; + }; + + sfp2: sfp-p19 { + compatible = "sff,sfp"; + i2c-bus = <&i2c3>; + los-gpio = <&gpio1 25 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&gpio1 24 GPIO_ACTIVE_LOW>; + }; + + sfp3: sfp-p20 { + compatible = "sff,sfp"; + i2c-bus = <&i2c2>; + los-gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&gpio1 13 GPIO_ACTIVE_LOW>; + }; +}; + +&gpio0 { + rtl8231_reset { + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "rtl8231-reset"; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + label = "u-boot-env"; + reg = <0x80000 0x40000>; + }; + + partition@c0000 { + label = "u-boot-env2"; + reg = <0xc0000 0x40000>; + }; + + partition@100000 { + compatible = "openwrt,uimage", "denx,uimage"; + label = "firmware"; + reg = <0x100000 0xe80000>; + openwrt,ih-magic = <0x12345000>; + }; + + partition@f80000 { + label = "firmware2"; + reg = <0xf80000 0xe80000>; + }; + + partition@1e00000 { + label = "jffs2"; + reg = <0x1e00000 0x200000>; + read-only; + }; + }; + }; +}; + +ðernet0 { + mdio-bus { + compatible = "realtek,rtl838x-mdio"; + regmap = <ðernet0>; + #address-cells = <1>; + #size-cells = <0>; + + EXTERNAL_PHY(0) + EXTERNAL_PHY(1) + EXTERNAL_PHY(2) + EXTERNAL_PHY(3) + EXTERNAL_PHY(4) + EXTERNAL_PHY(5) + EXTERNAL_PHY(6) + EXTERNAL_PHY(7) + + INTERNAL_PHY(8) + INTERNAL_PHY(9) + INTERNAL_PHY(10) + INTERNAL_PHY(11) + INTERNAL_PHY(12) + INTERNAL_PHY(13) + INTERNAL_PHY(14) + INTERNAL_PHY(15) + + EXTERNAL_SFP_PHY_FULL(24, 0) + EXTERNAL_SFP_PHY_FULL(25, 1) + EXTERNAL_SFP_PHY_FULL(26, 2) + EXTERNAL_SFP_PHY_FULL(27, 3) + }; +}; + +&switch0 { + ports { + #address-cells = <1>; + #size-cells = <0>; + + SWITCH_PORT(0, 1, qsgmii) + SWITCH_PORT(1, 2, qsgmii) + SWITCH_PORT(2, 3, qsgmii) + SWITCH_PORT(3, 4, qsgmii) + SWITCH_PORT(4, 5, qsgmii) + SWITCH_PORT(5, 6, qsgmii) + SWITCH_PORT(6, 7, qsgmii) + SWITCH_PORT(7, 8, qsgmii) + + SWITCH_PORT(8, 9, internal) + SWITCH_PORT(9, 10, internal) + SWITCH_PORT(10, 11, internal) + SWITCH_PORT(11, 12, internal) + SWITCH_PORT(12, 13, internal) + SWITCH_PORT(13, 14, internal) + SWITCH_PORT(14, 15, internal) + SWITCH_PORT(15, 16, internal) + + SWITCH_PORT(24, 17, qsgmii) + SWITCH_PORT(25, 18, qsgmii) + SWITCH_PORT(26, 19, qsgmii) + SWITCH_PORT(27, 20, qsgmii) + + port@28 { + ethernet = <ðernet0>; + reg = <28>; + phy-mode = "internal"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; +}; diff --git a/target/linux/realtek/image/rtl838x.mk b/target/linux/realtek/image/rtl838x.mk index b2e0cc91be..192b88fe54 100644 --- a/target/linux/realtek/image/rtl838x.mk +++ b/target/linux/realtek/image/rtl838x.mk @@ -12,6 +12,22 @@ define Device/allnet_all-sg8208m endef TARGET_DEVICES += allnet_all-sg8208m +define Device/apresia_aplgs120gtss + $(Device/cameo-fw) + SOC := rtl8382 + IMAGE_SIZE := 14848k + DEVICE_VENDOR := APRESIA + DEVICE_MODEL := ApresiaLightGS120GT-SS + UIMAGE_MAGIC := 0x12345000 + CAMEO_KERNEL_PART_SIZE := 1572864 + CAMEO_KERNEL_PART := 3 + CAMEO_ROOTFS_PART := 4 + CAMEO_CUSTOMER_SIGNATURE := 2 + CAMEO_BOARD_MODEL := APLGS120GTSS + CAMEO_BOARD_VERSION := 4 +endef +TARGET_DEVICES += apresia_aplgs120gtss + define Device/d-link_dgs-1210-10mp-f $(Device/d-link_dgs-1210) SOC := rtl8380 -- 2.30.2