From 58936d8d944e27b75c99b1c59cfeea3f253b03cb Mon Sep 17 00:00:00 2001 From: Jiri Slaby Date: Tue, 8 May 2007 00:36:13 -0700 Subject: [PATCH] Char: cyclades, create cy_pci_probe Move probing code to separate function for easy pci probing conversion. Signed-off-by: Jiri Slaby Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/char/cyclades.c | 623 ++++++++++++++++++++-------------------- 1 file changed, 318 insertions(+), 305 deletions(-) diff --git a/drivers/char/cyclades.c b/drivers/char/cyclades.c index a49232746438..e5de0409b37c 100644 --- a/drivers/char/cyclades.c +++ b/drivers/char/cyclades.c @@ -4698,7 +4698,8 @@ static int __init cy_detect_isa(void) #endif /* CONFIG_ISA */ } /* cy_detect_isa */ -static void plx_init(void __iomem * addr, __u32 initctl) +#ifdef CONFIG_PCI +static void __devinit plx_init(void __iomem * addr, __u32 initctl) { /* Reset PLX */ cy_writel(addr + initctl, readl(addr + initctl) | 0x40000000); @@ -4800,355 +4801,367 @@ static int __devinit cy_init_Ze(unsigned long cy_pci_phys0, return 0; } -/* - * --------------------------------------------------------------------- - * cy_detect_pci() - Test PCI bus presence and Cyclom-Ye/PCI. - * sets global variables and return the number of PCI boards found. - * --------------------------------------------------------------------- - */ -static int __init cy_detect_pci(void) +static int __devinit cy_pci_probe(struct pci_dev *pdev, + const struct pci_device_id *ent) { -#ifdef CONFIG_PCI - - struct pci_dev *pdev = NULL; unsigned char cyy_rev_id; - unsigned char cy_pci_irq = 0; - __u32 cy_pci_phys0, cy_pci_phys2; + unsigned char cy_pci_irq; + __u32 cy_pci_phys0, cy_pci_phys2, mailbox; void __iomem *cy_pci_addr0, *cy_pci_addr2; - unsigned short i, j, cy_pci_nchan, plx_ver; - unsigned short device_id, dev_index = 0; - __u32 mailbox; + unsigned int device_id; + unsigned short j, cy_pci_nchan, plx_ver; int retval; - for (i = 0; i < NR_CARDS; i++) { - /* look for a Cyclades card by vendor and device id */ - while ((device_id = cy_pci_dev_id[dev_index].device) != 0) { - if ((pdev = pci_get_device(PCI_VENDOR_ID_CYCLADES, - device_id, pdev)) == NULL) { - dev_index++; /* try next device id */ - } else { - break; /* found a board */ - } - } + retval = pci_enable_device(pdev); + if (retval) { + dev_err(&pdev->dev, "cannot enable device\n"); + return retval; + } - if (device_id == 0) - break; + /* read PCI configuration area */ + cy_pci_irq = pdev->irq; + cy_pci_phys0 = pci_resource_start(pdev, 0); + cy_pci_phys2 = pci_resource_start(pdev, 2); + pci_read_config_byte(pdev, PCI_REVISION_ID, &cyy_rev_id); - if (pci_enable_device(pdev)) - continue; + device_id = pdev->device & ~PCI_DEVICE_ID_MASK; - /* read PCI configuration area */ - cy_pci_irq = pdev->irq; - cy_pci_phys0 = pci_resource_start(pdev, 0); - cy_pci_phys2 = pci_resource_start(pdev, 2); - pci_read_config_byte(pdev, PCI_REVISION_ID, &cyy_rev_id); + if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo || + device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) { +#ifdef CY_PCI_DEBUG + printk("Cyclom-Y/PCI (bus=0x0%x, pci_id=0x%x, ", + pdev->bus->number, pdev->devfn); + printk("rev_id=%d) IRQ%d\n", + cyy_rev_id, (int)cy_pci_irq); + printk("Cyclom-Y/PCI:found winaddr=0x%lx " + "ctladdr=0x%lx\n", + (ulong)cy_pci_phys2, (ulong)cy_pci_phys0); +#endif - device_id &= ~PCI_DEVICE_ID_MASK; + if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) { + printk(" Warning: PCI I/O bit incorrectly " + "set. Ignoring it...\n"); + pdev->resource[2].flags &= ~IORESOURCE_IO; + } - if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo || - device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) { -#ifdef CY_PCI_DEBUG + /* Although we don't use this I/O region, we should + request it from the kernel anyway, to avoid problems + with other drivers accessing it. */ + retval = pci_request_regions(pdev, "Cyclom-Y"); + if (retval) { + printk(KERN_ERR "cyclades: failed to reserve " + "PCI resources\n"); + return retval; + } +#if defined(__alpha__) + if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo) { /* below 1M? */ printk("Cyclom-Y/PCI (bus=0x0%x, pci_id=0x%x, ", pdev->bus->number, pdev->devfn); printk("rev_id=%d) IRQ%d\n", cyy_rev_id, (int)cy_pci_irq); printk("Cyclom-Y/PCI:found winaddr=0x%lx " "ctladdr=0x%lx\n", - (ulong)cy_pci_phys2, (ulong)cy_pci_phys0); -#endif - - if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) { - printk(" Warning: PCI I/O bit incorrectly " - "set. Ignoring it...\n"); - pdev->resource[2].flags &= ~IORESOURCE_IO; - } - - /* Although we don't use this I/O region, we should - request it from the kernel anyway, to avoid problems - with other drivers accessing it. */ - if (pci_request_regions(pdev, "Cyclom-Y") != 0) { - printk(KERN_ERR "cyclades: failed to reserve " - "PCI resources\n"); - continue; - } -#if defined(__alpha__) - if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo) { /* below 1M? */ - printk("Cyclom-Y/PCI (bus=0x0%x, pci_id=0x%x, ", - pdev->bus->number, pdev->devfn); - printk("rev_id=%d) IRQ%d\n", - cyy_rev_id, (int)cy_pci_irq); - printk("Cyclom-Y/PCI:found winaddr=0x%lx " - "ctladdr=0x%lx\n", - (ulong)cy_pci_phys2, - (ulong)cy_pci_phys0); - printk("Cyclom-Y/PCI not supported for low " - "addresses in Alpha systems.\n"); - i--; - continue; - } + (ulong)cy_pci_phys2, + (ulong)cy_pci_phys0); + printk("Cyclom-Y/PCI not supported for low " + "addresses in Alpha systems.\n"); + return -EIO; + } #endif - cy_pci_addr0 = pci_iomap(pdev, 0, CyPCI_Yctl); - cy_pci_addr2 = pci_iomap(pdev, 2, CyPCI_Ywin); + cy_pci_addr0 = pci_iomap(pdev, 0, CyPCI_Yctl); + cy_pci_addr2 = pci_iomap(pdev, 2, CyPCI_Ywin); #ifdef CY_PCI_DEBUG - printk("Cyclom-Y/PCI: relocate winaddr=0x%lx " - "ctladdr=0x%lx\n", - (u_long)cy_pci_addr2, (u_long)cy_pci_addr0); + printk("Cyclom-Y/PCI: relocate winaddr=0x%lx " + "ctladdr=0x%lx\n", + (u_long)cy_pci_addr2, (u_long)cy_pci_addr0); #endif - cy_pci_nchan = (unsigned short)(CyPORTS_PER_CHIP * - cyy_init_card(cy_pci_addr2, 1)); - if (cy_pci_nchan == 0) { - printk("Cyclom-Y PCI host card with "); - printk("no Serial-Modules at 0x%lx.\n", - (ulong) cy_pci_phys2); - i--; - continue; - } - if ((cy_next_channel + cy_pci_nchan) > NR_PORTS) { - printk("Cyclom-Y/PCI found at 0x%lx ", - (ulong) cy_pci_phys2); - printk("but no channels are available.\n"); - printk("Change NR_PORTS in cyclades.c and " - "recompile kernel.\n"); - return i; - } - /* fill the next cy_card structure available */ - for (j = 0; j < NR_CARDS; j++) { - if (cy_card[j].base_addr == 0) - break; - } - if (j == NR_CARDS) { /* no more cy_cards available */ - printk("Cyclom-Y/PCI found at 0x%lx ", - (ulong) cy_pci_phys2); - printk("but no more cards can be used.\n"); - printk("Change NR_CARDS in cyclades.c and " - "recompile kernel.\n"); - return i; - } - - /* allocate IRQ */ - if (request_irq(cy_pci_irq, cyy_interrupt, - IRQF_SHARED, "Cyclom-Y", &cy_card[j])) { - printk("Cyclom-Y/PCI found at 0x%lx ", - (ulong) cy_pci_phys2); - printk("but could not allocate IRQ%d.\n", - cy_pci_irq); - return i; - } - - /* set cy_card */ - cy_card[j].base_phys = (ulong) cy_pci_phys2; - cy_card[j].ctl_phys = (ulong) cy_pci_phys0; - cy_card[j].base_addr = cy_pci_addr2; - cy_card[j].ctl_addr = cy_pci_addr0; - cy_card[j].irq = (int)cy_pci_irq; - cy_card[j].bus_index = 1; - cy_card[j].first_line = cy_next_channel; - cy_card[j].num_chips = cy_pci_nchan / 4; - cy_card[j].pdev = pdev; - pci_set_drvdata(pdev, &cy_card[j]); - - /* enable interrupts in the PCI interface */ - plx_ver = readb(cy_pci_addr2 + CyPLX_VER) & 0x0f; - switch (plx_ver) { - case PLX_9050: - - cy_writeb(cy_pci_addr0 + 0x4c, 0x43); + cy_pci_nchan = (unsigned short)(CyPORTS_PER_CHIP * + cyy_init_card(cy_pci_addr2, 1)); + if (cy_pci_nchan == 0) { + printk("Cyclom-Y PCI host card with "); + printk("no Serial-Modules at 0x%lx.\n", + (ulong) cy_pci_phys2); + return -EIO; + } + if ((cy_next_channel + cy_pci_nchan) > NR_PORTS) { + printk("Cyclom-Y/PCI found at 0x%lx ", + (ulong) cy_pci_phys2); + printk("but no channels are available.\n"); + printk("Change NR_PORTS in cyclades.c and " + "recompile kernel.\n"); + return -EIO; + } + /* fill the next cy_card structure available */ + for (j = 0; j < NR_CARDS; j++) { + if (cy_card[j].base_addr == 0) break; + } + if (j == NR_CARDS) { /* no more cy_cards available */ + printk("Cyclom-Y/PCI found at 0x%lx ", + (ulong) cy_pci_phys2); + printk("but no more cards can be used.\n"); + printk("Change NR_CARDS in cyclades.c and " + "recompile kernel.\n"); + return -EIO; + } - case PLX_9060: - case PLX_9080: - default: /* Old boards, use PLX_9060 */ - - plx_init(cy_pci_addr0, 0x6c); - /* For some yet unknown reason, once the PLX9060 reloads - the EEPROM, the IRQ is lost and, thus, we have to - re-write it to the PCI config. registers. - This will remain here until we find a permanent - fix. */ - pci_write_config_byte(pdev, PCI_INTERRUPT_LINE, - cy_pci_irq); - - cy_writew(cy_pci_addr0 + 0x68, - readw(cy_pci_addr0 + 0x68) | 0x0900); - break; - } + /* allocate IRQ */ + retval = request_irq(cy_pci_irq, cyy_interrupt, + IRQF_SHARED, "Cyclom-Y", &cy_card[j]); + if (retval) { + printk("Cyclom-Y/PCI found at 0x%lx ", + (ulong) cy_pci_phys2); + printk("but could not allocate IRQ%d.\n", + cy_pci_irq); + return retval; + } - /* print message */ - printk("Cyclom-Y/PCI #%d: 0x%lx-0x%lx, IRQ%d, ", - j + 1, (ulong)cy_pci_phys2, - (ulong) (cy_pci_phys2 + CyPCI_Ywin - 1), - (int)cy_pci_irq); - printk("%d channels starting from port %d.\n", - cy_pci_nchan, cy_next_channel); + /* set cy_card */ + cy_card[j].base_phys = (ulong) cy_pci_phys2; + cy_card[j].ctl_phys = (ulong) cy_pci_phys0; + cy_card[j].base_addr = cy_pci_addr2; + cy_card[j].ctl_addr = cy_pci_addr0; + cy_card[j].irq = (int)cy_pci_irq; + cy_card[j].bus_index = 1; + cy_card[j].first_line = cy_next_channel; + cy_card[j].num_chips = cy_pci_nchan / 4; + cy_card[j].pdev = pdev; + pci_set_drvdata(pdev, &cy_card[j]); - cy_next_channel += cy_pci_nchan; - } else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Lo) { - /* print message */ - printk("Cyclades-Z/PCI (bus=0x0%x, pci_id=0x%x, ", - pdev->bus->number, pdev->devfn); - printk("rev_id=%d) IRQ%d\n", - cyy_rev_id, (int)cy_pci_irq); - printk("Cyclades-Z/PCI: found winaddr=0x%lx " - "ctladdr=0x%lx\n", - (ulong)cy_pci_phys2, (ulong)cy_pci_phys0); - printk("Cyclades-Z/PCI not supported for low " - "addresses\n"); + /* enable interrupts in the PCI interface */ + plx_ver = readb(cy_pci_addr2 + CyPLX_VER) & 0x0f; + switch (plx_ver) { + case PLX_9050: + + cy_writeb(cy_pci_addr0 + 0x4c, 0x43); break; - } else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Hi) { -#ifdef CY_PCI_DEBUG - printk("Cyclades-Z/PCI (bus=0x0%x, pci_id=0x%x, ", - pdev->bus->number, pdev->devfn); - printk("rev_id=%d) IRQ%d\n", - cyy_rev_id, (int)cy_pci_irq); - printk("Cyclades-Z/PCI: found winaddr=0x%lx " - "ctladdr=0x%lx\n", - (ulong) cy_pci_phys2, (ulong) cy_pci_phys0); -#endif - cy_pci_addr0 = pci_iomap(pdev, 0, CyPCI_Zctl); - /* Disable interrupts on the PLX before resetting it */ - cy_writew(cy_pci_addr0 + 0x68, - readw(cy_pci_addr0 + 0x68) & ~0x0900); + case PLX_9060: + case PLX_9080: + default: /* Old boards, use PLX_9060 */ plx_init(cy_pci_addr0, 0x6c); - /* For some yet unknown reason, once the PLX9060 reloads - the EEPROM, the IRQ is lost and, thus, we have to - re-write it to the PCI config. registers. - This will remain here until we find a permanent - fix. */ + /* For some yet unknown reason, once the PLX9060 reloads + the EEPROM, the IRQ is lost and, thus, we have to + re-write it to the PCI config. registers. + This will remain here until we find a permanent + fix. */ pci_write_config_byte(pdev, PCI_INTERRUPT_LINE, - cy_pci_irq); + cy_pci_irq); - mailbox = (__u32)readl(&((struct RUNTIME_9060 __iomem *) - cy_pci_addr0)->mail_box_0); + cy_writew(cy_pci_addr0 + 0x68, + readw(cy_pci_addr0 + 0x68) | 0x0900); + break; + } - if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) { - printk(" Warning: PCI I/O bit incorrectly " - "set. Ignoring it...\n"); - pdev->resource[2].flags &= ~IORESOURCE_IO; - } + /* print message */ + printk("Cyclom-Y/PCI #%d: 0x%lx-0x%lx, IRQ%d, ", + j + 1, (ulong)cy_pci_phys2, + (ulong) (cy_pci_phys2 + CyPCI_Ywin - 1), + (int)cy_pci_irq); + printk("%d channels starting from port %d.\n", + cy_pci_nchan, cy_next_channel); - /* Although we don't use this I/O region, we should - request it from the kernel anyway, to avoid problems - with other drivers accessing it. */ - if (pci_request_regions(pdev, "Cyclades-Z") != 0) { - printk(KERN_ERR "cyclades: failed to reserve " - "PCI resources\n"); - continue; - } + cy_next_channel += cy_pci_nchan; + } else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Lo) { + /* print message */ + printk("Cyclades-Z/PCI (bus=0x0%x, pci_id=0x%x, ", + pdev->bus->number, pdev->devfn); + printk("rev_id=%d) IRQ%d\n", + cyy_rev_id, (int)cy_pci_irq); + printk("Cyclades-Z/PCI: found winaddr=0x%lx " + "ctladdr=0x%lx\n", + (ulong)cy_pci_phys2, (ulong)cy_pci_phys0); + printk("Cyclades-Z/PCI not supported for low " + "addresses\n"); + return -EIO; + } else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Hi) { +#ifdef CY_PCI_DEBUG + printk("Cyclades-Z/PCI (bus=0x0%x, pci_id=0x%x, ", + pdev->bus->number, pdev->devfn); + printk("rev_id=%d) IRQ%d\n", + cyy_rev_id, (int)cy_pci_irq); + printk("Cyclades-Z/PCI: found winaddr=0x%lx " + "ctladdr=0x%lx\n", + (ulong) cy_pci_phys2, (ulong) cy_pci_phys0); +#endif + cy_pci_addr0 = pci_iomap(pdev, 0, CyPCI_Zctl); + + /* Disable interrupts on the PLX before resetting it */ + cy_writew(cy_pci_addr0 + 0x68, + readw(cy_pci_addr0 + 0x68) & ~0x0900); + + plx_init(cy_pci_addr0, 0x6c); + /* For some yet unknown reason, once the PLX9060 reloads + the EEPROM, the IRQ is lost and, thus, we have to + re-write it to the PCI config. registers. + This will remain here until we find a permanent + fix. */ + pci_write_config_byte(pdev, PCI_INTERRUPT_LINE, + cy_pci_irq); - if (mailbox == ZE_V1) { - retval = cy_init_Ze(cy_pci_phys0, cy_pci_phys2, - cy_pci_addr0, cy_pci_irq, pdev); - if (retval < 0) - i--; - continue; - } else { - cy_pci_addr2 = pci_iomap(pdev, 2, CyPCI_Zwin); - } + mailbox = (__u32)readl(&((struct RUNTIME_9060 __iomem *) + cy_pci_addr0)->mail_box_0); + + if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) { + printk(" Warning: PCI I/O bit incorrectly " + "set. Ignoring it...\n"); + pdev->resource[2].flags &= ~IORESOURCE_IO; + } + + /* Although we don't use this I/O region, we should + request it from the kernel anyway, to avoid problems + with other drivers accessing it. */ + retval = pci_request_regions(pdev, "Cyclades-Z"); + if (retval) { + printk(KERN_ERR "cyclades: failed to reserve " + "PCI resources\n"); + return retval; + } + + if (mailbox == ZE_V1) { + retval = cy_init_Ze(cy_pci_phys0, cy_pci_phys2, + cy_pci_addr0, cy_pci_irq, pdev); + return retval; + } else { + cy_pci_addr2 = pci_iomap(pdev, 2, CyPCI_Zwin); + } #ifdef CY_PCI_DEBUG - printk("Cyclades-Z/PCI: relocate winaddr=0x%lx " - "ctladdr=0x%lx\n", - (ulong) cy_pci_addr2, (ulong) cy_pci_addr0); - if (mailbox == ZO_V1) { - cy_writel(&((struct RUNTIME_9060 *) - (cy_pci_addr0))->loc_addr_base, - WIN_CREG); - printk("Cyclades-8Zo/PCI: FPGA id %lx, ver " - "%lx\n", (ulong) (0xff & - readl(&((struct CUSTOM_REG *) - (cy_pci_addr2))->fpga_id)), - (ulong)(0xff & - readl(&((struct CUSTOM_REG *) - (cy_pci_addr2))-> - fpga_version))); - cy_writel(&((struct RUNTIME_9060 *) - (cy_pci_addr0))->loc_addr_base, - WIN_RAM); - } else { - printk("Cyclades-Z/PCI: New Cyclades-Z board. " - "FPGA not loaded\n"); - } + printk("Cyclades-Z/PCI: relocate winaddr=0x%lx " + "ctladdr=0x%lx\n", + (ulong) cy_pci_addr2, (ulong) cy_pci_addr0); + if (mailbox == ZO_V1) { + cy_writel(&((struct RUNTIME_9060 *) + (cy_pci_addr0))->loc_addr_base, + WIN_CREG); + printk("Cyclades-8Zo/PCI: FPGA id %lx, ver " + "%lx\n", (ulong) (0xff & + readl(&((struct CUSTOM_REG *) + (cy_pci_addr2))->fpga_id)), + (ulong)(0xff & + readl(&((struct CUSTOM_REG *) + (cy_pci_addr2))-> + fpga_version))); + cy_writel(&((struct RUNTIME_9060 *) + (cy_pci_addr0))->loc_addr_base, + WIN_RAM); + } else { + printk("Cyclades-Z/PCI: New Cyclades-Z board. " + "FPGA not loaded\n"); + } #endif - /* The following clears the firmware id word. This - ensures that the driver will not attempt to talk to - the board until it has been properly initialized. - */ - if ((mailbox == ZO_V1) || (mailbox == ZO_V2)) - cy_writel(cy_pci_addr2 + ID_ADDRESS, 0L); - - /* This must be a Cyclades-8Zo/PCI. The extendable - version will have a different device_id and will - be allocated its maximum number of ports. */ - cy_pci_nchan = 8; - - if ((cy_next_channel + cy_pci_nchan) > NR_PORTS) { - printk("Cyclades-8Zo/PCI found at 0x%lx but" - "no channels are available.\nChange " - "NR_PORTS in cyclades.c and recompile " - "kernel.\n", (ulong)cy_pci_phys2); - return i; - } + /* The following clears the firmware id word. This + ensures that the driver will not attempt to talk to + the board until it has been properly initialized. + */ + if ((mailbox == ZO_V1) || (mailbox == ZO_V2)) + cy_writel(cy_pci_addr2 + ID_ADDRESS, 0L); + + /* This must be a Cyclades-8Zo/PCI. The extendable + version will have a different device_id and will + be allocated its maximum number of ports. */ + cy_pci_nchan = 8; + + if ((cy_next_channel + cy_pci_nchan) > NR_PORTS) { + printk("Cyclades-8Zo/PCI found at 0x%lx but" + "no channels are available.\nChange " + "NR_PORTS in cyclades.c and recompile " + "kernel.\n", (ulong)cy_pci_phys2); + return -EIO; + } - /* fill the next cy_card structure available */ - for (j = 0; j < NR_CARDS; j++) { - if (cy_card[j].base_addr == 0) - break; - } - if (j == NR_CARDS) { /* no more cy_cards available */ - printk("Cyclades-8Zo/PCI found at 0x%lx but" - "no more cards can be used.\nChange " - "NR_CARDS in cyclades.c and recompile " - "kernel.\n", (ulong)cy_pci_phys2); - return i; - } + /* fill the next cy_card structure available */ + for (j = 0; j < NR_CARDS; j++) { + if (cy_card[j].base_addr == 0) + break; + } + if (j == NR_CARDS) { /* no more cy_cards available */ + printk("Cyclades-8Zo/PCI found at 0x%lx but" + "no more cards can be used.\nChange " + "NR_CARDS in cyclades.c and recompile " + "kernel.\n", (ulong)cy_pci_phys2); + return -EIO; + } #ifdef CONFIG_CYZ_INTR - /* allocate IRQ only if board has an IRQ */ - if ((cy_pci_irq != 0) && (cy_pci_irq != 255)) { - if (request_irq(cy_pci_irq, cyz_interrupt, - IRQF_SHARED, "Cyclades-Z", - &cy_card[j])) { - printk("Cyclom-8Zo/PCI found at 0x%lx " - "but could not allocate " - "IRQ%d.\n", (ulong)cy_pci_phys2, - cy_pci_irq); - return i; - } + /* allocate IRQ only if board has an IRQ */ + if ((cy_pci_irq != 0) && (cy_pci_irq != 255)) { + retval = request_irq(cy_pci_irq, cyz_interrupt, + IRQF_SHARED, "Cyclades-Z", + &cy_card[j]); + if (retval) { + printk("Cyclom-8Zo/PCI found at 0x%lx " + "but could not allocate " + "IRQ%d.\n", (ulong)cy_pci_phys2, + cy_pci_irq); + return retval; } + } #endif /* CONFIG_CYZ_INTR */ - /* set cy_card */ - cy_card[j].base_phys = cy_pci_phys2; - cy_card[j].ctl_phys = cy_pci_phys0; - cy_card[j].base_addr = cy_pci_addr2; - cy_card[j].ctl_addr = cy_pci_addr0; - cy_card[j].irq = (int)cy_pci_irq; - cy_card[j].bus_index = 1; - cy_card[j].first_line = cy_next_channel; - cy_card[j].num_chips = -1; - cy_card[j].pdev = pdev; - pci_set_drvdata(pdev, &cy_card[j]); - - /* print message */ + /* set cy_card */ + cy_card[j].base_phys = cy_pci_phys2; + cy_card[j].ctl_phys = cy_pci_phys0; + cy_card[j].base_addr = cy_pci_addr2; + cy_card[j].ctl_addr = cy_pci_addr0; + cy_card[j].irq = (int)cy_pci_irq; + cy_card[j].bus_index = 1; + cy_card[j].first_line = cy_next_channel; + cy_card[j].num_chips = -1; + cy_card[j].pdev = pdev; + pci_set_drvdata(pdev, &cy_card[j]); + + /* print message */ #ifdef CONFIG_CYZ_INTR - /* don't report IRQ if board is no IRQ */ - if ((cy_pci_irq != 0) && (cy_pci_irq != 255)) - printk("Cyclades-8Zo/PCI #%d: 0x%lx-0x%lx, " - "IRQ%d, ", j + 1, (ulong)cy_pci_phys2, - (ulong) (cy_pci_phys2 + CyPCI_Zwin - 1), - (int)cy_pci_irq); - else + /* don't report IRQ if board is no IRQ */ + if ((cy_pci_irq != 0) && (cy_pci_irq != 255)) + printk("Cyclades-8Zo/PCI #%d: 0x%lx-0x%lx, " + "IRQ%d, ", j + 1, (ulong)cy_pci_phys2, + (ulong) (cy_pci_phys2 + CyPCI_Zwin - 1), + (int)cy_pci_irq); + else #endif /* CONFIG_CYZ_INTR */ - printk("Cyclades-8Zo/PCI #%d: 0x%lx-0x%lx, ", - j + 1, (ulong)cy_pci_phys2, - (ulong)(cy_pci_phys2 + CyPCI_Zwin - 1)); + printk("Cyclades-8Zo/PCI #%d: 0x%lx-0x%lx, ", + j + 1, (ulong)cy_pci_phys2, + (ulong)(cy_pci_phys2 + CyPCI_Zwin - 1)); + + printk("%d channels starting from port %d.\n", + cy_pci_nchan, cy_next_channel); + cy_next_channel += cy_pci_nchan; + } + + return 0; +} +#endif + +/* + * --------------------------------------------------------------------- + * cy_detect_pci() - Test PCI bus presence and Cyclom-Ye/PCI. + * sets global variables and return the number of PCI boards found. + * --------------------------------------------------------------------- + */ +static int __init cy_detect_pci(void) +{ +#ifdef CONFIG_PCI + struct pci_dev *pdev = NULL; + unsigned int i, device_id, dev_index = 0; - printk("%d channels starting from port %d.\n", - cy_pci_nchan, cy_next_channel); - cy_next_channel += cy_pci_nchan; + for (i = 0; i < NR_CARDS; i++) { + /* look for a Cyclades card by vendor and device id */ + while ((device_id = cy_pci_dev_id[dev_index].device) != 0) { + if ((pdev = pci_get_device(PCI_VENDOR_ID_CYCLADES, + device_id, pdev)) == NULL) { + dev_index++; /* try next device id */ + } else { + break; /* found a board */ + } } + + if (device_id == 0) + break; + + i -= !!cy_pci_probe(pdev, &cy_pci_dev_id[dev_index]); } return i; -- 2.30.2