From 5affb607720d734ca572b8a77c5c7d62d3042b6f Mon Sep 17 00:00:00 2001 From: Gregory Bean Date: Thu, 9 Sep 2010 16:38:02 -0700 Subject: [PATCH] gpio: sx150x: correct and refine reset-on-probe behavior Replace the arbitrary software-reset call from the device-probe method, because: - It is defective. To work correctly, it should be two byte writes, not a single word write. As it stands, it does nothing. - Some devices with sx150x expanders installed have their NRESET pins ganged on the same line, so resetting one causes the others to reset - not a nice thing to do arbitrarily! - The probe, usually taking place at boot, implies a recent hard-reset, so a software reset at this point is just a waste of energy anyway. Therefore, make it optional, defaulting to off, as this will match the common case of probing at powerup and also matches the current broken no-op behavior. Signed-off-by: Gregory Bean Reviewed-by: Jean Delvare Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/gpio/sx150x.c | 26 +++++++++++++++++++++----- include/linux/i2c/sx150x.h | 4 ++++ 2 files changed, 25 insertions(+), 5 deletions(-) diff --git a/drivers/gpio/sx150x.c b/drivers/gpio/sx150x.c index b42f42ca70c3..823559ab0e24 100644 --- a/drivers/gpio/sx150x.c +++ b/drivers/gpio/sx150x.c @@ -459,17 +459,33 @@ static int sx150x_init_io(struct sx150x_chip *chip, u8 base, u16 cfg) return err; } -static int sx150x_init_hw(struct sx150x_chip *chip, - struct sx150x_platform_data *pdata) +static int sx150x_reset(struct sx150x_chip *chip) { - int err = 0; + int err; - err = i2c_smbus_write_word_data(chip->client, + err = i2c_smbus_write_byte_data(chip->client, chip->dev_cfg->reg_reset, - 0x3412); + 0x12); if (err < 0) return err; + err = i2c_smbus_write_byte_data(chip->client, + chip->dev_cfg->reg_reset, + 0x34); + return err; +} + +static int sx150x_init_hw(struct sx150x_chip *chip, + struct sx150x_platform_data *pdata) +{ + int err = 0; + + if (pdata->reset_during_probe) { + err = sx150x_reset(chip); + if (err < 0) + return err; + } + err = sx150x_i2c_write(chip->client, chip->dev_cfg->reg_misc, 0x01); diff --git a/include/linux/i2c/sx150x.h b/include/linux/i2c/sx150x.h index ee3049cb9ba5..52baa79d69a7 100644 --- a/include/linux/i2c/sx150x.h +++ b/include/linux/i2c/sx150x.h @@ -63,6 +63,9 @@ * IRQ lines will appear. Similarly to gpio_base, the expander * will create a block of irqs beginning at this number. * This value is ignored if irq_summary is < 0. + * @reset_during_probe: If set to true, the driver will trigger a full + * reset of the chip at the beginning of the probe + * in order to place it in a known state. */ struct sx150x_platform_data { unsigned gpio_base; @@ -73,6 +76,7 @@ struct sx150x_platform_data { u16 io_polarity; int irq_summary; unsigned irq_base; + bool reset_during_probe; }; #endif /* __LINUX_I2C_SX150X_H */ -- 2.30.2