From 909d9faae2a447110aa061070145297fffe129cb Mon Sep 17 00:00:00 2001 From: Yuval Mintz Date: Wed, 22 Apr 2015 12:47:32 +0300 Subject: [PATCH] bnx2x: Prevent inner-reload while VFs exist On some feature changes, driver employes an inner-reload flow where it resets the function and re-configures it with the new required set of parameters. Such a flow proves fatal to any VF since those were not intended to be used while HW is being reset underneath, causing them [at best] to lose all connectivity. This changes driver behavior to fail all configuration changes [e.g., mtu change] requested of the driver in case VFs are active. Signed-off-by: Yuval Mintz Signed-off-by: Ariel Elior Signed-off-by: David S. Miller --- .../net/ethernet/broadcom/bnx2x/bnx2x_cmn.c | 43 +++++++++++++++---- .../ethernet/broadcom/bnx2x/bnx2x_ethtool.c | 17 ++++++++ 2 files changed, 51 insertions(+), 9 deletions(-) diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c index 2f63467bce46..6f7dc81581ff 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c @@ -4809,6 +4809,23 @@ netdev_features_t bnx2x_fix_features(struct net_device *dev, { struct bnx2x *bp = netdev_priv(dev); + if (pci_num_vf(bp->pdev)) { + netdev_features_t changed = dev->features ^ features; + + /* Revert the requested changes in features if they + * would require internal reload of PF in bnx2x_set_features(). + */ + if (!(features & NETIF_F_RXCSUM) && !bp->disable_tpa) { + features &= ~NETIF_F_RXCSUM; + features |= dev->features & NETIF_F_RXCSUM; + } + + if (changed & NETIF_F_LOOPBACK) { + features &= ~NETIF_F_LOOPBACK; + features |= dev->features & NETIF_F_LOOPBACK; + } + } + /* TPA requires Rx CSUM offloading */ if (!(features & NETIF_F_RXCSUM)) { features &= ~NETIF_F_LRO; @@ -4839,15 +4856,18 @@ int bnx2x_set_features(struct net_device *dev, netdev_features_t features) else flags &= ~GRO_ENABLE_FLAG; - if (features & NETIF_F_LOOPBACK) { - if (bp->link_params.loopback_mode != LOOPBACK_BMAC) { - bp->link_params.loopback_mode = LOOPBACK_BMAC; - bnx2x_reload = true; - } - } else { - if (bp->link_params.loopback_mode != LOOPBACK_NONE) { - bp->link_params.loopback_mode = LOOPBACK_NONE; - bnx2x_reload = true; + /* VFs or non SRIOV PFs should be able to change loopback feature */ + if (!pci_num_vf(bp->pdev)) { + if (features & NETIF_F_LOOPBACK) { + if (bp->link_params.loopback_mode != LOOPBACK_BMAC) { + bp->link_params.loopback_mode = LOOPBACK_BMAC; + bnx2x_reload = true; + } + } else { + if (bp->link_params.loopback_mode != LOOPBACK_NONE) { + bp->link_params.loopback_mode = LOOPBACK_NONE; + bnx2x_reload = true; + } } } @@ -4931,6 +4951,11 @@ int bnx2x_resume(struct pci_dev *pdev) } bp = netdev_priv(dev); + if (pci_num_vf(bp->pdev)) { + DP(BNX2X_MSG_IOV, "VFs are enabled, can not change MTU\n"); + return -EPERM; + } + if (bp->recovery_state != BNX2X_RECOVERY_DONE) { BNX2X_ERR("Handling parity error recovery. Try again later\n"); return -EAGAIN; diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c index e3d853cab7c9..48ed005ba73f 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c @@ -1843,6 +1843,12 @@ static int bnx2x_set_ringparam(struct net_device *dev, "set ring params command parameters: rx_pending = %d, tx_pending = %d\n", ering->rx_pending, ering->tx_pending); + if (pci_num_vf(bp->pdev)) { + DP(BNX2X_MSG_IOV, + "VFs are enabled, can not change ring parameters\n"); + return -EPERM; + } + if (bp->recovery_state != BNX2X_RECOVERY_DONE) { DP(BNX2X_MSG_ETHTOOL, "Handling parity error recovery. Try again later\n"); @@ -2899,6 +2905,12 @@ static void bnx2x_self_test(struct net_device *dev, u8 is_serdes, link_up; int rc, cnt = 0; + if (pci_num_vf(bp->pdev)) { + DP(BNX2X_MSG_IOV, + "VFs are enabled, can not perform self test\n"); + return; + } + if (bp->recovery_state != BNX2X_RECOVERY_DONE) { netdev_err(bp->dev, "Handling parity error recovery. Try again later\n"); @@ -3468,6 +3480,11 @@ static int bnx2x_set_channels(struct net_device *dev, channels->rx_count, channels->tx_count, channels->other_count, channels->combined_count); + if (pci_num_vf(bp->pdev)) { + DP(BNX2X_MSG_IOV, "VFs are enabled, can not set channels\n"); + return -EPERM; + } + /* We don't support separate rx / tx channels. * We don't allow setting 'other' channels. */ -- 2.30.2