From abc7ed2c58860fc1363129efbe9e8c60f81a802c Mon Sep 17 00:00:00 2001
From: Weijie Gao <hackpascal@gmail.com>
Date: Sat, 29 Dec 2018 17:22:32 +0800
Subject: [PATCH] ath79: add support for D-Link DIR-859 A1

Hardware spec of DIR-859 A1:
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9880

USB is supported on the PCB but not connected.

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or the u-boot
   failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted. Otherwise the u-boot
   will enter failsafe mode as the checksum of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the firmware
   checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin, just
   upgrade the factory.bin through the u-boot failsafe interface and then goto
   step 2.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
[squash commits, use common seama recipes, sync factory image recipe
with ramips version]
Signed-off-by: Mathias Kresin <dev@kresin.me>
---
 .../ath79/base-files/etc/board.d/01_leds      |   3 +
 .../ath79/base-files/etc/board.d/02_network   |   5 +
 .../etc/hotplug.d/firmware/10-ath9k-eeprom    |   4 +
 .../etc/hotplug.d/firmware/11-ath10k-caldata  |   4 +
 target/linux/ath79/config-4.14                |   1 +
 .../ath79/dts/qca9563_dlink_dir-859-a1.dts    | 177 ++++++++++++++++++
 target/linux/ath79/image/generic.mk           |  29 +++
 7 files changed, 223 insertions(+)
 create mode 100644 target/linux/ath79/dts/qca9563_dlink_dir-859-a1.dts

diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds
index 04c8964c9e..cc718b4d96 100755
--- a/target/linux/ath79/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/base-files/etc/board.d/01_leds
@@ -28,6 +28,9 @@ buffalo,whr-g301n)
 	ucidef_set_led_switch "lan3" "LAN3" "$boardname:green:lan3" "switch0" "0x08"
 	ucidef_set_led_switch "lan4" "LAN4" "$boardname:green:lan4" "switch0" "0x10"
 	;;
+dlink,dir-859-a1)
+	ucidef_set_led_switch "internet" "WAN" "$boardname:green:internet" "switch0" "0x20"
+	;;
 etactica,eg200)
 	ucidef_set_led_netdev "lan" "LAN" "$boardname:red:eth0" "eth0"
 	ucidef_set_led_oneshot "modbus" "Modbus" "$boardname:red:modbus" "100" "33"
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index 004ab59573..1251048e08 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -158,6 +158,7 @@ ath79_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan" "6@eth0"
 		;;
+	dlink,dir-859-a1|\
 	tplink,tl-wr1043nd-v4)
 		ucidef_add_switch "switch0" \
 			"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
@@ -234,6 +235,10 @@ ath79_setup_macs()
 		lan_mac=$(mtd_get_mac_text "mac" 4)
 		wan_mac=$(mtd_get_mac_text "mac" 24)
 		;;
+	dlink,dir-859-a1)
+		lan_mac=$(mtd_get_mac_ascii devdata "lanmac")
+		wan_mac=$(mtd_get_mac_ascii devdata "wanmac")
+		;;
 	elecom,wrc-300ghbk2-i)
 		wan_mac=$(macaddr_add "$(mtd_get_mac_binary ART 4098)" -2)
 		;;
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index f6ff582150..2da9250ddf 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -105,6 +105,10 @@ case "$FIRMWARE" in
 		ath9k_eeprom_extract "art" 4096 1088
 		ath9k_patch_fw_mac_crc $(mtd_get_mac_text "mac" 4) 2
 		;;
+	dlink,dir-859-a1)
+		ath9k_eeprom_extract "art" 4096 1088
+		ath9k_patch_fw_mac $(mtd_get_mac_ascii devdata "wlan24mac") 2
+		;;
 	iodata,wn-ac1167dgr|\
 	iodata,wn-ac1600dgr2|\
 	iodata,wn-ag300dgr)
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 53f57be824..b9a987d418 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -92,6 +92,10 @@ case "$FIRMWARE" in
 		ath10kcal_extract "art" 20480 2116
 		ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 0) -1)
 		;;
+	dlink,dir-859-a1)
+		ath10kcal_extract "art" 20480 2116
+		ath10kcal_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
+		;;
 	glinet,gl-x750)
 		ath10kcal_extract "art" 20480 2116
 		ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
diff --git a/target/linux/ath79/config-4.14 b/target/linux/ath79/config-4.14
index 969136ddde..5a2c685d40 100644
--- a/target/linux/ath79/config-4.14
+++ b/target/linux/ath79/config-4.14
@@ -168,6 +168,7 @@ CONFIG_MTD_PHYSMAP=y
 CONFIG_MTD_SPI_NOR=y
 CONFIG_MTD_SPLIT_FIRMWARE=y
 CONFIG_MTD_SPLIT_LZMA_FW=y
+CONFIG_MTD_SPLIT_SEAMA_FW=y
 CONFIG_MTD_SPLIT_TPLINK_FW=y
 CONFIG_MTD_SPLIT_UIMAGE_FW=y
 CONFIG_MTD_TPLINK_PARTS=y
diff --git a/target/linux/ath79/dts/qca9563_dlink_dir-859-a1.dts b/target/linux/ath79/dts/qca9563_dlink_dir-859-a1.dts
new file mode 100644
index 0000000000..23b4cc5126
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_dlink_dir-859-a1.dts
@@ -0,0 +1,177 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca956x.dtsi"
+
+/ {
+	model = "D-Link DIR-859 A1";
+	compatible = "dlink,dir-859-a1", "qca,qca9563";
+
+	aliases {
+		led-boot = &power;
+		led-failsafe = &power;
+		led-running = &power;
+		led-upgrade = &power;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		wps {
+			label = "dir-859-a1:green:wps";
+			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+		};
+
+		power: power {
+			label = "dir-859-a1:green:power";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+		};
+
+		internet {
+			label = "dir-859-a1:green:internet";
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan {
+			label = "dir-859-a1:green:wlan";
+			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys-polled";
+		poll-interval = <20>;
+
+		wps {
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+
+		reset {
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+
+	gpio-export {
+		compatible = "gpio-export";
+		#size-cells = <0>;
+
+		gpio_switch_reset {
+			gpio-export,name = "dir-859-a1:reset:switch";
+			gpio-export,output = <1>;
+			gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&uart {
+	status = "okay";
+};
+
+&gpio {
+	status = "okay";
+};
+
+&pcie {
+	status = "okay";
+};
+
+&spi {
+	num-cs = <1>;
+
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <30000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "bootloader";
+				reg = <0x000000 0x40000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "bdcfg";
+				reg = <0x040000 0x10000>;
+				read-only;
+			};
+
+			partition@50000 {
+				label = "devdata";
+				reg = <0x050000 0x10000>;
+				read-only;
+			};
+
+			partition@60000 {
+				label = "devconf";
+				reg = <0x060000 0x10000>;
+				read-only;
+			};
+
+			partition@70000 {
+				compatible = "seama";
+				label = "firmware";
+				reg = <0x070000 0xf80000>;
+			};
+
+			art: partition@ff0000 {
+				label = "art";
+				reg = <0xff0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	phy-mask = <0>;
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		phy-mode = "sgmii";
+
+		qca,ar8327-initvals = <
+			0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+			0x10 0x81000080 /* POWER_ON_STRIP */
+			0x50 0xcc35cc35 /* LED_CTRL0 */
+			0x54 0xcb37cb37 /* LED_CTRL1 */
+			0x58 0x00000000 /* LED_CTRL2 */
+			0x5c 0x00f3cf00 /* LED_CTRL3 */
+			0x7c 0x0000007e /* PORT0_STATUS */
+			>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	pll-data = <0x03000101 0x00000101 0x00001919>;
+
+	phy-mode = "sgmii";
+	phy-handle = <&phy0>;
+};
+
+&wmac {
+	status = "okay";
+	qca,no-eeprom;
+};
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index b2f83ba58c..8dd5dab7ca 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -2,6 +2,7 @@ include ./common-buffalo.mk
 include ./common-netgear.mk
 
 DEVICE_VARS += ADDPATTERN_ID ADDPATTERN_VERSION
+DEVICE_VARS += SEAMA_SIGNATURE SEAMA_MTDBLOCK
 
 define Build/cybertan-trx
 	@echo -n '' > $@-empty.bin
@@ -53,6 +54,23 @@ define Build/nec-fw
   mv $@.new $@
 endef
 
+define Device/seama
+  KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
+  KERNEL_INITRAMFS := $$(KERNEL) | seama
+  IMAGES += factory.bin
+  SEAMA_MTDBLOCK := 1
+
+  # 64 bytes offset:
+  # - 28 bytes seama_header
+  # - 36 bytes of META data (4-bytes aligned)
+  IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
+  IMAGE/sysupgrade.bin := \
+	$$(IMAGE/default) | seama | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
+  IMAGE/factory.bin := \
+	$$(IMAGE/default) | pad-rootfs -x 64 | seama | seama-seal | check-size $$$$(IMAGE_SIZE)
+  SEAMA_SIGNATURE :=
+endef
+
 define Device/avm_fritz300e
   ATH_SOC := ar7242
   DEVICE_TITLE := AVM FRITZ!WLAN Repeater 300E
@@ -192,6 +210,17 @@ define Device/dlink_dir-835-a1
 endef
 TARGET_DEVICES += dlink_dir-835-a1
 
+define Device/dlink_dir-859-a1
+  $(Device/seama)
+  ATH_SOC := qca9563
+  DEVICE_TITLE := D-LINK DIR-859 A1
+  IMAGE_SIZE := 15872k
+  DEVICE_PACKAGES :=  kmod-usb-core kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
+  SEAMA_SIGNATURE := wrgac37_dlink.2013gui_dir859
+  SUPPORTED_DEVICES += dir-859-a1
+endef
+TARGET_DEVICES += dlink_dir-859-a1
+
 define Device/elecom_wrc-300ghbk2-i
   ATH_SOC := qca9563
   DEVICE_TITLE := ELECOM WRC-300GHBK2-I
-- 
2.30.2