From fd787048a9a8530c7138d629d3dbeabdfaaec000 Mon Sep 17 00:00:00 2001 From: Stefan Wahren Date: Mon, 29 May 2017 13:57:21 +0200 Subject: [PATCH] dt-bindings: qca7000-spi: Rework binding In preparation for the QCA7000 UART binding rework the binding document. Signed-off-by: Stefan Wahren Signed-off-by: David S. Miller --- .../bindings/net/qca-qca7000-spi.txt | 49 +++++++++++-------- 1 file changed, 29 insertions(+), 20 deletions(-) diff --git a/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt b/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt index c74989c0d8ac..a37f65678399 100644 --- a/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt +++ b/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt @@ -1,29 +1,38 @@ -* Qualcomm QCA7000 (Ethernet over SPI protocol) +* Qualcomm QCA7000 -Note: The QCA7000 is useable as a SPI device. In this case it must be defined -as a child of a SPI master in the device tree. +The QCA7000 is a serial-to-powerline bridge with a host interface which could +be configured either as SPI or UART slave. This configuration is done by +the QCA7000 firmware. + +(a) Ethernet over SPI + +In order to use the QCA7000 as SPI device it must be defined as a child of a +SPI master in the device tree. Required properties: -- compatible : Should be "qca,qca7000" -- reg : Should specify the SPI chip select -- interrupts : The first cell should specify the index of the source interrupt - and the second cell should specify the trigger type as rising edge -- spi-cpha : Must be set -- spi-cpol: Must be set +- compatible : Should be "qca,qca7000" +- reg : Should specify the SPI chip select +- interrupts : The first cell should specify the index of the source + interrupt and the second cell should specify the trigger + type as rising edge +- spi-cpha : Must be set +- spi-cpol : Must be set Optional properties: -- interrupt-parent : Specify the pHandle of the source interrupt +- interrupt-parent : Specify the pHandle of the source interrupt - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at. - Numbers smaller than 1000000 or greater than 16000000 are invalid. Missing - the property will set the SPI frequency to 8000000 Hertz. -- local-mac-address: 6 bytes, MAC address -- qca,legacy-mode : Set the SPI data transfer of the QCA7000 to legacy mode. - In this mode the SPI master must toggle the chip select between each data - word. In burst mode these gaps aren't necessary, which is faster. - This setting depends on how the QCA7000 is setup via GPIO pin strapping. - If the property is missing the driver defaults to burst mode. - -Example: + Numbers smaller than 1000000 or greater than 16000000 + are invalid. Missing the property will set the SPI + frequency to 8000000 Hertz. +- local-mac-address : see ./ethernet.txt +- qca,legacy-mode : Set the SPI data transfer of the QCA7000 to legacy mode. + In this mode the SPI master must toggle the chip select + between each data word. In burst mode these gaps aren't + necessary, which is faster. This setting depends on how + the QCA7000 is setup via GPIO pin strapping. If the + property is missing the driver defaults to burst mode. + +SPI Example: /* Freescale i.MX28 SPI master*/ ssp2: spi@80014000 { -- 2.30.2